Synthesis of 3,5-Disubstituted Isoxazoles and Isoxazolines in Deep Eutectic Solvents

The synthesis of different 3,5-disubstituted isoxazoles and related isoxazolines using choline chloride:urea as deep eutectic solvent (DES) in a one-pot three step reaction has been accomplished successfully. The use of highly nucleophilic functionalized DES did not affect the process where highly electrophilic reagents or intermediates are involved. The presence of DES showed to be essential since the reaction in absence of this media did not proceed. The DES media could be reused up to five times without a detrimental effect on the yield of the reaction. To exemplify the synthetic potential of this methodology, the reaction was scaled up to the gram scale without any noticeable problem. Finally, different isoxazoles were easily transformed into β-aminoenones.

Copper Nanoparticles in Click Chemistry

Conspectus: The challenges of the 21st century demand scientific and technological achievements that must be developed under sustainable and environmentally benign practices. In this vein, click chemistry and green chemistry walk hand in hand on a pathway of rigorous principles that help to safeguard the health of our planet against negligent and uncontrolled production. Copper-catalyzed azide–alkyne cycloaddition (CuAAC), the paradigm of a click reaction, is one of the most reliable and widespread synthetic transformations in organic chemistry, with multidisciplinary applications. Nanocatalysis is a green chemistry tool that can increase the inherent effectiveness of CuAAC because of the enhanced catalytic activity of nanostructured metals and their plausible reutilization capability as heterogeneous catalysts. This Account describes our contribution to click chemistry using unsupported and supported copper nanoparticles (CuNPs) as catalysts prepared by chemical reduction. Cu(0)NPs (3.0 ± 1.5 nm) in tetrahydrofuran were found to catalyze the reaction of terminal alkynes and organic azides in the presence of triethylamine at rates comparable to those achieved under microwave heating (10–30 min in most cases). Unfortunately, the CuNPs underwent dissolution under the reaction conditions and consequently could not be recovered. Compelling experimental evidence on the in situ generation of highly reactive copper(I) chloride and the participation of copper(I) acetylides was provided. The supported CuNPs were found to be more robust and efficient catalyst than the unsupported counterpart in the following terms: (a) the multicomponent variant of CuAAC could be applied; (b) the metal loading could be substantially decreased; (c) reactions could be conducted in neat water; and (d) the catalyst could be recovered easily and reutilized. In particular, the catalyst composed of oxidized CuNPs (Cu2O/CuO, 6.0 ± 2.0 nm) supported on carbon (CuNPs/C) was shown to be highly versatile and very effective in the multicomponent and regioselective synthesis of 1,4-disubstituted 1,2,3-triazoles in water from organic halides as azido precursors; magnetically recoverable CuNPs (3.0 ± 0.8 nm) supported on MagSilica could be alternatively used for the same purpose under similar conditions. Incorporation of an aromatic substituent at the 1-position of the triazole could be accomplished using the same CuNPs/C catalytic system starting from aryldiazonium salts or anilines as azido precursors. CuNPs/C in water also catalyzed the regioselective double-click synthesis of β-hydroxy-1,2,3-triazoles from epoxides. Furthermore, alkenes could be also used as azido precursors through a one-pot CuNPs/C-catalyzed azidosulfenylation–CuAAC sequential protocol, providing β-methylsulfanyl-1,2,3-triazoles in a stereo- and regioselective manner. In all types of reaction studied, CuNPs/C exhibited better behavior than some commercial copper catalysts with regard to the metal loading, reaction time, yield, and recyclability. Therefore, the results of this study also highlight the utility of nanosized copper in click chemistry compared with bulk copper sources.

STUDIES OF FUNCTIONALIZED NANOPARTICLES FOR SMART SELF-ASSEMBLY AND AS CONTROLLED DRUG DELIVERY

This dissertation is related to the studies of functionalized nanoparticles for self-assembly and as controlled drug delivery system. The whole topic is composed of two parts. In the first part, the research was conducted to design and synthesize a new type of ionic peptide-functionalized copolymer conjugates for self-assembly into nanoparticle fibers and 3D scaffolds with the ability of multi-drug loading and governing the release rate of each drug for tissue engineering. The self-assembly study confirmed that such peptide-functionalized amphiphilic copolymers underwent different self-assembly behavior. The bigger nanoparticles were more easily assembled into nanoparticle fibers and 3D scaffolds with larger pore size, while the smaller nanoparticle underwent faster self-assembly to form more compact 3D scaffolds with smaller porosity but more stable structure. Controlled release studies confirmed the ability of governing simultaneous release of different model drugs with independent release rate from a same scaffold. Cytotoxicity tests showed that all synthesized peptides, copolymers and peptide-copolymer conjugates were biocompatible with SW-620 cell lines and NIH3T3 cell lines. This new type of self-assembled scaffolds combined the advantages of peptide nanofibers and versatile controlled release of polymeric nanoparticles to achieve simultaneous multi-drug loading and controlled release of each drug, uniform distribution and flexibility of hydrogel scaffolds. The investigations in second part were first to design and synthesize organic biocide-loaded nanoparticles for low-leaching wood preservation using a cost-effective one-pot method to synthesize amphiphilic chitosan-g-PMMA nanoparticles loading with ~25-28 wt.% of the fungicide tebuconazole with particle size of ~100 nm diameter by FESEM. FESEM analysis confirmed efficient penetration of nanoparticles throughout the treated wooden stake with dimension of 19 × 19 × 455 mm^3. Leaching studies showed that biocide introduced into sapwood via nanoparticles leached only ~9% compared with the amount leached from tebuconazole solution-treated control, while soil jar tests showed that the nanoparticle-treated wood blocks were effectively protected from biological decay tested against G. trabeum, a brown rot fungus. Copper oxide nanoparticles with and without polymer stabilizers were also investigated to use as inorganic wood preservatives to clarify the factor affecting copper leaching from treated wood. Copper oxide nanoparticles with uniform diameters of ~10 nm and ~50 nm were prepared, and the leachates from southern pine sapwood treated with these nanoparticles were analyzed. It was found by TEM and EDS analysis that significant numbers of nanoparticles leached from the treated wood. The 50 nm nanoparticles leached slightly less than a soluble copper salt control, but 10 nm nanoparticles leached substantially more than the control. The effect of polymer stabilizers on nanoparticle leaching was also investigated. Results showed that polymer stabilizers increased leaching. The trends showed that nanoparticle size was a major factor in copper leaching.

Développement d’outils moléculaires pour la tomographie d’émission par positrons

Résumé : L’imagerie TEP est une modalité puissante qui permet de suivre d’infimes concentrations de traceurs marqués pour la détection de cancers et d’autres pathologies. Il y a actuellement un intérêt croissant pour le développement de peptides comme outils diagnostiques et de traitement en oncologie. Cet intérêt se justifie entre autres par le fait que les peptides sont tolérants à la présence de chélateurs bifonctionnels ou de groupements prosthétiques pour le marquage avec divers radiométaux (64Cu, T1/2 = 12,7 h, 68Ga, T1/2 = 68 min, etc.) ou le 18F (T1/2 = 109,8 min) sans perte de leur activité biologique. L’objectif des travaux rapportés dans ce document était de développer des outils moléculaires innovateurs et efficaces qui facilitent le marquage de peptides pour l’imagerie TEP. Il s’agit spécifiquement d’un chélateur bifonctionnel et d’une méthode de conjugaison rapide et sélective de groupe prosthétique. Sur un volet, un chélateur bifonctionnel analogue de la lysine avec des ligands méthylhydroxamates a été synthétisé en solution par double bisalkylation. Les résultats préliminaires indiquent une faible chélation avec le Cu(II), mais sont à poursuivre avec les 68Ga et 89Zr. Pour le second volet de radiomarquage au 18F, les procédures synthétiques ont été optimisées en deux étapes, soient le marquage du groupe prothétique et sa conjugaison au peptide. Tout d’abord, des conditions de marquage par une réaction de SNAr en présence de 18F- ont été développées pour donner le groupe prosthétique 18F-thioester nécessaire à la conjugaison. Par la suite, sa conjugaison au peptide par la réaction de ligation chémosélective, ce qui implique trois étapes 1) une transthioestérification favorisée entre les groupements thioester et thiol des segments de peptides; 2) un réarrangement irréversible de l’intermédiaire thioester en N-(oxyalkyl)amide, suivi; 3) du clivage de l’auxiliaire. Par les présents travaux, il a été prouvé que la nouvelle méthodologie en un seul pot réactionnel accélère la réaction et permet le marquage au 18F de peptides non protégés, limitant ainsi les réactions secondaires et le nombre d’étapes après le marquage des peptides. La conjugaison du groupe prothétique à un composé et un peptide modèle se produit en 26-55 min comparativement aux 48 h des conditions originales rapportées. La méthode proposée permet également le marquage de peptides non protégés. Dans le futur, le chélateur bifonctionnel et le groupe prothétique seront conjugués à différents dérivés peptidiques ciblant des récepteurs impliqués dans le cancer et des tests de compétition, de saturation, de biodistribution et d’imagerie µTEP seront effectués.

A novel single pot synthesis of binuclear copper(II) complexes of macrocyclic and macroacyclic compartmental ligands: Structures and magnetic properties

Two binuclear copper(II) complexes one (complex 1) with a macrocyclic ligand (H(2)L1) and other (complex 2) with a macroacyclic (end-off type) compartmental ligand (HL2) have been synthesized from single pot template synthesis involving copper(II) nitrate, 1,2diaminoethane, 4-methyl-2,6-diformylphenol, and sodium azide. Structure analysis of complex I reveals that there are actually two half molecules present in the asymmetric unit and so two complexes (molecule-I and molecule-II) are present in unit cell, although they show slight differences. The two Cu(II) centers are in distorted square pyramidal coordination environment with two endogenous phenoxo bridges provided by the phenolate of H(2)L1 I having Cu-Cu separations of 2.9133(10) angstrom and 2.9103(10) in the two molecules. In complex 2 the coordination environments around two Cu(II) centers are asymmetric, Cu1 is in distorted square pyramidal environment whereas, the coordination environment around Cu2 is distorted octahedral. The two Cu(II) centers in complex 2 are connected by two different kinds of bridges, one is endogenous phenoxo bridge provided by the phenolate of the ligand HL2 and the other is exogenous azido bridge (mu-(1),(l) type) with Cu-Cu distance of 3.032(10) angstrom. Variable temperature magnetic studies show that two Cu(II) centers in both the complexes are strongly antiferromagnetically coupled with J = -625 +/- 5 cm(-1) and J = -188.6 +/- 1cm(-1) for complex 1 and 2, respectively. (C) 2006 Elsevier B.V. All rights reserved.

Assessing movements of three buoy line types using DSTmilli Loggers: Implications for entanglements of bottlenose dolphins in the crab pot fishery

A study was conducted in October 2006 in the Charleston, South Carolina area to test the movements of three different buoy line types to determine which produced a preferred profile that could reduce the risk of dolphin entanglement. Tests on diamond-braided nylon commonly used in the crab pot fishery were compared with stiffened line of Esterpro and calf types in both shallow and deep water environments using DSTmilli data loggers. Loggers were placed at intervals along the lines to record depth, and thus movements, over a 24 hour period. Three observers viewed video animations and charts created for each of the six trial days from the collected logger data and provided their opinions on the most desirable line type that fit set criteria. A quantitative analysis (ANCOVA) of the data was conducted taking into consideration daily tidal fluctuations and logger movements. Loggers tracking the tides had an r2 value approaching 1.00 and produced little movement other than with the tides. Conversely, r2 values approaching 0.00 were less affected by tidal movement and influenced by currents that cause more erratic movement. Results from this study showed that stiffened line, in particular the medium lay Esterpro type, produced the more desirable profiles that could reduce risk of dolphin entanglement. Combining the observer’s results with the ANCOVA results, Esterpro was chosen nearly 60% of the time as opposed to the nylon line which was only chosen 10% of the time. ANCOVA results showed that the stiffened lines performed better in both the shallow and deep water environments, while the nylon line only performed better during one trial in a deep water set, most probably due to the increased current velocities experienced that day. (58pp.)(PDF contains 68 pages)

Evaluation of a new fishing pot trap (Lege) in River Rima, north western Nigeria

Based on the findings and diagnostic survey, a new fishing trap, christened Lege trap was designed and fabricated, and the performance evaluated. The 8-valve Lege trap was assessed concurrently with Malian and Ndurutu traps by the fishermen in the study area. The experiment was conducted in a randomized complete block design with one factor each replicated three times. Data collected on fish diversity number, biomass and size were subjected to descriptive statistics and analysis of variance. The results showed that 22 fish species belonging to thirteen families were caught. The prototype (Lege) trap recorded higher species diversity index (0.90) than the Malian (0.50) and Ndurutu (0.50) traps. The Lege trap also accounted for the largest number (55%) and biomass (63%) of fish caught which was significantly (P<0.05) higher than those of the Malian and Nduutu traps were. The mean length (15.03~c5.70cm), weight (60.43~c48.61g) and girth (4.77~c1.65cm) of fishes caught in the Lege trap were also significantly (P0.05) higher than those caught in the other two traps. These results demonstrated better performance of the new trap than the two conventional traps, even though the sizes of some of the fish species caught in all the traps were below those allowed by the Sokoto State Fisheries Edict where the study was conducted. Therefore, since it is desirable to develop conservation-oriented trap at a least cost, it is necessary to research further on the number of valves and mesh size of the new trap

Influence of number of valves on catch composition of a fishing pot trap (Lege) in River Rima, north western Nigeria

Three types of prototype (Lege) traps with different numbers of entrance valves were evaluated in River Rima, north western Nigeria. The traps contained 4,6 and 8 valves, tagged 4-V, 6-V and 8-V respectively. The experiment was carried out in a randomized complete block design with one factor each replicated three times. Data collected on fish diversity, number biomass and sizes were subjected to descriptive statistics and analysis of variance. The results of the catch composition showed close diversity index of 0.86 for 6-V, 0.80 for 8-V and 0.60 for 4-V Lege traps. However, the number (41%) and biomass 48%) of fish caught in the 6-V Lege trap were significantly (P0.05) higher than those caught in the other traps. There was no definite trend in the sizes (length and girth) of fish caught in the traps. On the basis of species diversity, and the number and biomass of fish caught, the 6-V Lege showed preference for adoption than the other two traps. However, further studies are recommended on the appropriate mesh size net for the trap in line with the provisions of fisheries edicts

Influence of number of valves on catch composition of a fishing pot trap (Lege) in River Rima, north western Nigeria

Three types of prototype (Lege) traps with different numbers of entrance valves were evaluated in River Rima, north western Nigeria. The traps contained 4,6 and 8 valves, tagged 4-V, 6-V and 8-V respectively. The experiment was carried out in a randomized complete block design with one factor each replicated three times. Data collected on fish diversity, number, biomass and sizes were subjected to descriptive statistics and analysis of variance. The results of the catch composition showed close diversity index of 0.86 for 6-V, 0.80 for 8-V and 0.60 for 4-V Lege traps. However, the number (41%) and biomass (48%) of fish caught in the 6-V Lege trap were significantly (P<0.05) higher than those caught in the other traps. There was no definite trend in the sizes (length and girth) of fish caught in the traps. On the basis of species diversity, and the number and biomass of fish caught, the 6-V Lege showed preference for adoption than the other two traps. However, further studies are recommended on the appropriate mesh size net for the trap in line with the provisions of fisheries edicts

A study of the crab pot as a fishing gear

The crab pot as a fishing gear was introduced in Maryland waters, following some years of greatly expanded use in Virginia, during the 1939 season, and was widely used during 1940. The 1941 session of the Maryland Legislature, however, illegalized the crab pot. Since that time the device has been given up almost entirely by Maryland fishermen, its attempted use in a commercial way having persisted in diminishing numbers in only one region of the state.

Clay pot irrigation for tomato (Lycopersicon esculentum Mill) production in the north east semiarid region of Ethiopia

Water shortage is one of the major constraints for production of horticultural crops in arid and semiarid regions. A field experiment was conducted to determine irrigation water and fertilizer use efficiency, growth and yield of tomato under clay pot irrigation at the experimental site of Sekota Dryland Agricultural Research Center, Lalibela, Ethiopia in 2009/10. The experiment comprised of five treatments including furrow irrigated control and clay pot irrigation with different plant population and fertilization methods, which were arranged in Randomized Complete Block Design with three replications. The highest total and marketable fruit yields were obtained from clay pot irrigation combined with application of nitrogen fertilizer with irrigation water irrespective of difference in plant population. The clay pot irrigation had seasonal water use of up to 143.71 mm, which resulted in significantly higher water use efficiency (33.62 kg m^-3) as compared to the furrow irrigation, which had a seasonal water use of 485.50 mm, and a water use efficiency of 6.67 kg m^-3. Application of nitrogen fertilizer with irrigation water in clay pots improved fertilizer use efficiency of tomato by up to 52% than band application with furrow or clay pot irrigation. Thus, clay pot irrigation with 33,333 plants ha^-1 and nitrogen fertilizer application with irrigation water in clay pots was the best method for increasing the yield of tomato while economizing the use of water and nitrogen fertilizer in a semiarid environment.

"Racism in a Melting Pot...?" Trinidadian mid-life transnational migrants' views on race and colour-class on return to their homes of descent

This paper deals with second-generation, one-and-a-half generation and ‘‘prolonged sojourner” Trinidadian transnational migrants, who have decided to ‘return’ to the birthplace of their parents. Based on 40 in-depth interviews, the paper considers both the positive and critical things that these youthful transnational migrants report about returning to, and living in, this multi-ethnic plural society and the salience of racial and colour-class stratification as part of their return migration experiences. Our qualitative analysis is based on the narratives provided by these youthful returnees, as relayed ‘‘in their own words”, presenting critical reflections on racism, racial identities and experiences as transnational Trinidadians. It is clear that it is contexts such as contemporary working environments, family and community that act as the reference points for the adaptation ‘‘back home” of this strongly middle-class cohort. We accordingly encounter a diverse, sometimes contesting set of racial issues that emerge as salient concerns for these returnees. The consensus is that matters racial remain as formidable legacies in the hierarchical stratification of Trinidadian society for a sizeable number. Many of our respondents reported the positive aspects of racial affirmation on return. But for another sub-set, the fact that multi-ethnic and multi-cultural mixing are proudly embraced in Trinidad meant that it was felt that return experiences were not overly hindered, or blighted by obstacles of race and colour-class. For these returnees, Trinidad and Tobago is seen as representing a 21st century ‘‘Melting Pot”. But for others the continued existence of racial divisions within society – between ethnic groups and among those of different skin shades – was lamented. In the views of these respondents, too much racial power is still ascribed to ‘near-whiteness’. But for the most part, the returnees felt that where race played a part in their new lives, this generally served to advantage them. However, although the situation in Trinidad appears to have been moderated by assumptions that it remains a racial ‘Melting Pot’, the analysis strongly suggests that the colour-class system of stratification is still playing an essential role, along with racial stereotyping in society at large.

Estudo da corrosão de aços de elevado limite elástico e das suas uniões com metais duros ou cermet e com aço/WC-Co em 'NA''CL' 0,6 mol 'L POT. -1'

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo das propriedades ópticas e estruturais de espinélios do tipo 'ZNAL IND. 2 O IND. 4' contendo 'EU POT. 3+' ou 'TB POT. 3+'

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Harmonic superspace from the Ad'S IND. 5' × 'S POT. 5' pure spinor formalism

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)