Hydraulic conductivity in response to exchangeable sodium percentage and solution salt concentration

Hydraulic conductivity is determined in laboratory assays to estimate the flow of water in saturated soils. However, the results of this analysis, when using distilled or deionized water, may not correspond to field conditions in soils with high concentrations of soluble salts. This study therefore set out to determine the hydraulic conductivity in laboratory conditions using solutions of different electrical conductivities in six soils representative of the State of Pernambuco, with the exchangeable sodium percentage adjusted in the range of 5-30%. The results showed an increase in hydraulic conductivity with both decreasing exchangeable sodium percentage and increasing electrical conductivity in the solution. The response to the treatments was more pronounced in soils with higher proportion of more active clays. Determination of hydraulic conductivity in laboratory is routinely performed with deionized or distilled water. However, in salt affected soils, these determinations should be carried out using solutions of electrical conductivity different from 0 dS m-1, with values close to those determined in the saturation extracts.

Solvent effects on solution enthalpies of adamantyl derivatives

Solution enthalpies of 1-bromoadamantane, 1-adamantanol, and 2-adamantanone in a large set of protic and aprotic solvents are reported at 298.15 K. Solvent effects on the solution processes of these solutes are analyzed in terms of a modified TAKA equation, involving delta(cav) h (s) as the cavity term. The nature and magnitude of the major interactions which influence these processes are assessed and discussed in terms of the solutes' characteristics. New insights on the solution processes under scrutiny are presented.

Solution enthalpies of hydroxylic compounds

Solution enthalpies of adamantan-1-ol, 2-methyl- butan-2-ol, and 3-methylbutan-1-ol have been measured at 298.15 K, in a set of 16 protogenic and non-protogenic solvents. The identification and quantification of solvent effects on the solution processes under study were performed using quantitative-structure property relationships. The results are discussed in terms of solute-solvent-solvent interactions and also in terms of the influence of compound's size and position of its hydroxyl group.

Study of the one dimensional and transient bioheat transfer equation: Multi-layer solution development and applications

: In this work we derive an analytical solution given by Bessel series to the transient and one-dimensional (1D) bioheat transfer equation in a multi-layer region with spatially dependent heat sources. Each region represents an independent biological tissue characterized by temperature-invariant physiological parameters and a linearly temperature dependent metabolic heat generation. Moreover, 1D Cartesian, cylindrical or spherical coordinates are used to define the geometry and temperature boundary conditions of first, second and third kinds are assumed at the inner and outer surfaces. We present two examples of clinical applications for the developed solution. In the first one, we investigate two different heat source terms to simulate the heating in a tumor and its surrounding tissue, induced during a magnetic fluid hyperthermia technique used for cancer treatment. To obtain an accurate analytical solution, we determine the error associated with the truncated Bessel series that defines the transient solution. In the second application, we explore the potential of this model to study the effect of different environmental conditions in a multi-layered human head model (brain, bone and scalp). The convective heat transfer effect of a large blood vessel located inside the brain is also investigated. The results are further compared with a numerical solution obtained by the Finite Element Method and computed with COMSOL Multi-physics v4.1 (c). (c) 2013 Elsevier Ltd. All rights reserved.

A 5GHz/1.8V CMOS Active Balun Integrated with LNA

The development of high performance monolithic RF front-ends requires innovative RF circuit design to make the best of a good technology. A fully differential approach is usually preferred, due to its well-known properties. Although the differential approach must be preserved inside the chip, there are cases where the input signal is single-ended such as RF image filters and IF filters in a RF receiver. In these situations, a stage able to convert single-ended into differential signals (balun) is needed. The most cited topology, which is capable of providing high gain, consists on a differential stage with one of the two inputs grounded. Unfortunately, this solution has some drawbacks when implemented monolithically. This work presents the design and simulated results of an innovative high-performance monolithic single to differential converter, which overcomes the limitations of the circuits.The integration of the monolithic active balun circuit with an LNA on a 0.18μm CMOS process is also reported. The circuits presented here are aimed at 802.11a. Section 2 describes the balun circuit and section 3 presents its performance when it is connected to a conventional single-ended LNA. Section 4 shows the simulated performance results focused at phase/amplitude balance and noise figure. Finally, the last section draws conclusions and future work.

Competências associadas ao ensino das ciências no âmbito da educação Pré-Escolar e no ensino do 1º ciclo do Ensino Básico

Mestrado (PES II), Educação Pré-Escolar e Ensino do 1º Ciclo do Ensino Básico, 1 de Julho de 2014, Universidade dos Açores.

Acesso remoto via infra-estrutura de teste IEEE1149.1 a dispositivos lógicos programáveis

Actualmente verifica-se que a complexidade dos sistemas informáticos tem vindo a aumentar, fazendo parte das nossas ferramentas diárias de trabalho a utilização de sistemas informáticos e a utilização de serviços online. Neste âmbito, a internet obtém um papel de destaque junto das universidades, ao permitir que alunos e professores possam interagir mais facilmente. A internet e a educação baseada na Web vêm oferecer acesso remoto a qualquer informação independentemente da localização ou da hora. Como consequência, qualquer pessoa com uma ligação à internet, ao poder adquirir informações sobre um determinado tema junto dos maiores peritos, obtém vantagens significativas. Os laboratórios remotos são uma solução muito valorizada no que toca a interligar tecnologia e recursos humanos em ambientes que podem estar afastados no tempo ou no espaço. A criação deste tipo de laboratórios e a sua utilidade real só é possível porque as tecnologias de comunicação emergentes têm contribuído de uma forma muito relevante para melhorar a sua disponibilização à distância. A necessidade de criação de laboratórios remotos torna-se imprescindível para pesquisas relacionadas com engenharia que envolvam a utilização de recursos escassos ou de grandes dimensões. Apoiado neste conceito, desenvolveu-se um laboratório remoto para os alunos de engenharia que precisam de testar circuitos digitais numa carta de desenvolvimento de hardware configurável, permitindo a utilização deste recurso de uma forma mais eficiente. O trabalho consistiu na criação de um laboratório remoto de baixo custo, com base em linguagens de programação open source, sendo utilizado como unidade de processamento um router da ASUS com o firmware OpenWrt. Este firmware é uma distribuição Linux para sistemas embutidos. Este laboratório remoto permite o teste dos circuitos digitais numa carta de desenvolvimento de hardware configurável em tempo real, utilizando a interface JTAG. O laboratório desenvolvido tem a particularidade de ter como unidade de processamento um router. A utilização do router como servidor é uma solução muito pouco usual na implementação de laboratórios remotos. Este router, quando comparado com um computador normal, apresenta uma capacidade de processamento e memória muito inferior, embora os testes efectuados provassem que apresenta um desempenho muito adequado às expectativas.

UV-Vis spectroscopic study preferential solvation and intermolecular interactions in methanol/1-propanol/acetonitrile by means of solvatochromic probes

Solvatochromic UV-Vis shifts of four indicators (4-nitroaniline, 4-nitroanisole, 4-nitrophenol and N,N-dimethy-1-4-nitro aniline) have been measured at 298.15 K in the ternary mixture methano1/1-propanol/acetonitrile (MeOH/1-PrOH/MeCN) in a total of 22 mole fractions, along with 18 additional mole fractions for each of the corresponding binary mixtures, MeOH/1-PrOH, 1-PrOH/MeCN and MeOH/MeCN. These values, combined with our previous experimental results for 2,6-dipheny1-4-(2,4,6-triphenylpyridinium-1-yl)phenolate (Reichardt's betaine dye) in the same mixtures, permitted the computation of the Kamlet-Taft solvent parameters, alpha, beta, and pi*. The rationalization of the spectroscopic behavior of each probe within each mixture's whole mole fraction range was achieved through the use of the Bosch and Roses preferential solvation model. The applied model allowed the identification of synergistic behaviors in MeCN/alcohol mixtures and thus to infer the existence of solvent complexes in solution. Also, the addition of small amounts of MeCN to the binary mixtures was seen to cause a significant variation in pi*, whereas the addition of alcohol to MeCN mixtures always lead to a sudden change in a and The behavior of these parameters in the ternary mixture was shown to be mainly determined by the contributions of the underlying binary mixtures. (C) 2014 Elsevier B.V. All rights reserved.

A remote engineering solution for automating a roller hearth kiln

Remote engineering (also known as online engineering) may be defined as a combination of control engineering and telematics. In this area, specific activities require computacional skills in order to develop projects where electrical devives are monitored and / or controlled, in an intercative way, through a distributed network (e.g. Intranet or Internet). In our specific case, we will be dealing with an industrial plant. Within the last few years, there has been an increase in the number of activities related to remote engineering, which may be connected to the phenomenon of the large extension experienced by the Internet (e.g. bandwith, number of users, development tools, etc.). This increase opens new and future possibilities to the implementation of advance teleworking (or e-working) positions. In this paper we present the architecture for a remote application, accessible through the Internet, able to monitor and control a roller hearth kiln, used in a ceramics industry for firing materials. The proposed architecture is based on a micro web server, whose main function is to monitor and control the firing process, by reading the data from a series of temperature sensors and by controlling a series of electronic valves and servo motors. This solution is also intended to be a low-cost alternative to other potential solutions. The temperature readings are obtained through K-type thermopairs and the gas flow is controlled through electrovalves. As the firing process should not be stopped before its complete end, the system is equipped with a safety device for that specific purpose. For better understanding the system to be automated and its operation we decided to develop a scale model (100:1) and experiment on it the devised solution, based on a Micro Web Server.

Solution enthalpies of hydroxylic compounds

Solution enthalpies of adamantan-1-ol, 2-methyl- butan-2-ol, and 3-methylbutan-1-ol have been measured at 298.15 K, in a set of 16 protogenic and non-protogenic solvents. The identification and quantification of solvent effects on the solution processes under study were performed using quantitative-structure property relationships. The results are discussed in terms of solute-solvent-solvent interactions and also in terms of the influence of compound's size and position of its hydroxyl group.

Is the electric vehicle a solution for the wind power integration in the portuguese power system?

The integration of Plug-in electric vehicles in the transportation sector has a great potential to reduce oil dependency, the GHG emissions and to contribute for the integration of renewable sources into the electricity generation mix. Portugal has a high share of wind energy, and curtailment may occur, especially during the off-peak hours with high levels of hydro generation. In this context, the electric vehicles, seen as a distributed storage system, can help to reduce the potential wind curtailments and, therefore, increase the integration of wind power into the power system. In order to assess the energy and environmental benefits of this integration, a methodology based on a unit commitment and economic dispatch is adapted and implemented. From this methodology, the thermal generation costs, the CO2 emissions and the potential wind generation curtailment are computed. Simulation results show that a 10% penetration of electric vehicles in the Portuguese fleet would increase electrical load by 3% and reduce wind curtailment by only 26%. This results from the fact that the additional generation required to supply the electric vehicles is mostly thermal. The computed CO2 emissions of the EV are 92 g CO2/kWh which become closer to those of some new ICE engines.

Explicit series solution for a glucose-induced electrical activity model of pancreatic beta-cells

In this work, we present the explicit series solution of a specific mathematical model from the literature, the Deng bursting model, that mimics the glucose-induced electrical activity of pancreatic beta-cells (Deng, 1993). To serve to this purpose, we use a technique developed to find analytic approximate solutions for strongly nonlinear problems. This analytical algorithm involves an auxiliary parameter which provides us with an efficient way to ensure the rapid and accurate convergence to the exact solution of the bursting model. By using the homotopy solution, we investigate the dynamical effect of a biologically meaningful bifurcation parameter rho, which increases with the glucose concentration. Our analytical results are found to be in excellent agreement with the numerical ones. This work provides an illustration of how our understanding of biophysically motivated models can be directly enhanced by the application of a newly analytic method.

Dimensionamento de pilares mistos aço-betão segundo a EN 1994-1-1 através de uma aplicação informática

O presente trabalho debruça-se sobre as estruturas mistas aço-betão, com foco nos pilares mistos e no seu dimensionamento segundo a norma europeia EN1994-1-1 (EC4) [1]. Um pilar misto aço-betão pode definir-se como um elemento de aço, laminado ou composto, que trabalha em conjunto com o betão, podendo as secções serem classificados como revestidas ou preenchidas. Com a crescente evolução das técnicas construtivas, as estruturas mistas aço-betão aparecem como soluções viáveis e seguras, tornando-se numa opção competitiva em relação às soluções tradicionais de betão armado e de aço estrutural. Isto, devido à grande capacidade de carga proporcionada por secções mais reduzidas, à boa relação de rigidez e bom comportamento perante os fenómenos de encurvadura. Com o surgimento da recente norma europeia EC4, não obstante a complexidade das metodologias de verificação da segurança propostas, há uma maior confiança na utilização deste tipo de estrutura por parte dos projetistas. É neste contexto que surge a necessidade de desenvolver ferramentas de cálculo expedito que possam ser utilizadas em gabinete de projeto, salvaguardando todos os aspectos regulamentares de verificação da segurança preconizados no EC4, de que é exemplo o dimensionamento de pilares mistos abordados no presente trabalho. De forma a validar a ferramenta desenvolvida é proposto um caso de estudo, com o objectivo de obter soluções de pilares mistos com dimensões otimizadas, fazendo as verificações previstas no EC4. Os resultados obtidos na ferramenta são comparados com os resultados obtidos através de cálculos analíticos.

An immunofluorescence test for diagnosis of ophthalmic herpes in a mouse corneal model

Herpes simplex virus type 1 (HSV-1) ophthalmic disease is the most common cause of corneal blindness in humans world-wide. Current culture techniques for HSV take several days and commercially available HSV laboratory based diagnostic techniques vary in sensitivity. Our study was conducted to evaluate the use of a quicker and simpler method to herpes ophthalmic diagnosis. Corneal smears were made by firm imprints of infected mouse eyes to glass slides, after smears were fixated with cold acetone, and an indirect immunofluorescence (IIF) method was performed using monoclonal antibodies in a murine model of ophthalmic herpes. Eye swabs from infected mice were inoculated in Vero cells for virus isolation. Cytology and histology of the eye were also performed, using hematoxylin-eosin routine. Mouse eyes were examined by slit-lamp biomicroscopy for evidence of herpetic disease at various times postinoculation. We made a comparative evaluation of sensitivity, specificity and speed of methods for laboratory detection of HSV. Our results indicate that this IIF method is quick, sensitive, specific and can be useful in the diagnosis of ophthalmic herpes as demonstrated in an animal model.

Strategic analysis on urban mobility

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Management from the NOVA – School of Business and Economics