Moisture relationships for the Southern Hemisphere

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Effect of heat-moisture treatment on the structural, physicochemical, and rheological characteristics of arrowroot starch

The effect of heat-moisture treatment on structural, physicochemical, and rheological characteristics of arrowroot starch was investigated. Heat-moisture treatment was performed with starch samples conditioned to 28% moisture at 100℃ for 2, 4, 8, and 16 h. Structural and physicochemical characterization of native and modified starches, as well as rheological assays with gels of native and 4 h modified starches subjected to acid and sterilization stresses were performed. Arrowroot starch had 23.1% of amylose and a CA-type crystalline pattern that changed over the treatment time to A-type. Modified starches had higher pasting temperature and lower peak viscosity while breakdown viscosity practically disappeared, independently of the treatment time. Gelatinization temperature and crystallinity increased, while enthalpy, swelling power, and solubility decreased with the treatment. Gels from modified starches, independently of the stress conditions, were found to have more stable apparent viscosities and higher G' and G″ than gels from native starch. Heat-moisture treatment caused a reorganization of starch chains that increased molecular interactions. This increase resulted in higher paste stability and strengthened gels that showed higher resistance to shearing and heat, even after acid or sterilization conditions. A treatment time of 4 h was enough to deeply changing the physicochemical properties of starch.

Influence of wood moisture content on modulus of elasticity on tension paralllel to the grain of brasilian species

Periodically, when necessary, standard documents are revised in order to analyze inconsistencies and to include considerations according new realities verified. In this sense, aiming to quantify the wood moisture content influence on modulus of elasticity, it was applied tension tests parallel to the grain for six specimens of different strength classes of wood, considering nominal moisture of 12, 20, 25, and 30% in Brazil. The present paper examine the adequacy of the current Brazilian standard ABNT NBR7190:1997, in review, about the adoption of a first degree equation to describe the influence of wood moisture content for timber structures design. It was obtained a new first degree equation which leads to statically equivalent estimations when compared with results by ABNT NBR7190:1997 equation. However, as recommendations it could be maintain the current expression for the next text of the referred document review, without prejudice to statistical significance of the estimates.

Influence of moisture content in some mechanical properties of two brazilian tropical wood species

This study aimed, with the aid of analysis of variance (ANOVA), to investigate and quantify the influence of moisture ranging between 12% and over 30% (fiber saturation) on the mechanical properties: strength and modulus of elasticity in compression and in tension parallel to grain; modulus of rupture and modulus of elasticity in static bending; shear strength parallel to grain considering wood species Ipê (Tabebuia sp) and Angelim Araroba (Vataireopsis araroba). Tests were performed according to the assumptions and calculating methods Brazilian standard ABNT NBR 7190, Anexx B, totalizing 400 tests. Results of ANOVA revealed a significant reduction (16% on average) for mechanical properties wood due to the increase in moisture content from 12% to over 30% (fiber saturation). The same behavior also occurred when assembly containing the two species was considered.

Moisture content and its influence on the roughness and noise emission during wood machining

Numerous factors influencing the surface quality of wood after machining, among them we highlight the machining parameters and the properties of the wood. In the analysis of the influence of these factors on machining and in determining the quality measurement systems are used to obtain surface characteristics, these systems are divided into methods of contact and non-contact. The method for mechanical contact performed with the aid of the surface roughness tester is the most valued in the measurement of roughness of wood, however, aiming at a greater agility in these measurements, there is a need to seek alternatives for evaluation of surface quality, and one of these options is to use the forms of indirect measurements of this quality, as for example, the use of noise emission during the machining process. With this, the aim was to analyze the influence of the moisture content of the wood, at different levels, on surface quality of the species Pinus elliottii, determined by the method of mechanical probing move and relate this roughness with the sound emission issued for each class of humidity, during machining. The planning of experiments and statistical analyses were performed with the help of Taguchi method. The specimens were conditioned in greenhouses climatizadoras automatics for obtaining three classes of humidity. Machining tests of wooden pieces were performed on a machining center specific for this type of material. The roughness values were measured by a roughness verifier and the noise emission values were measured by for a measurer sound pressure level. Statistically significant differences were observed, the significance level of 10 %, on roughness and noise emission between the three levels of moisture. It was observed that with the increase in the moisture content occurred an increase of roughness and a reduction in noise emission. Monitoring of surface quality through noise level is an interesting alternative to the method of mechanical contact.

EC38-118 Soil and Moisture Conservation in Nebraska

When the white men first explored Nebraska, they found little erosion taking place. They found the hills, particularly in eastern Nebraska, covered with a dense growth of grass, underlain with a thick mat of decaying debris. The valleys were even more densely covered with the water-loving grasses and sedges. The soil underneath the prairie was black and spongy, the result of centuries of accumulating humus. The valleys bordering the streams were boggy and abounded with springs. Clear water flowed constantly in the streams. The upland draws in the more favorable parts of the state were heavily covered with the big bluestem and slough grass. Springs occurred in many of these. Soil erosion in Nebraska has not progressed to as great an extent as in states to the east and to the south. This is because of the comparatively lower rainfall in Nebraska, because the land has been farmed for fewer years in this state, and because some Nebraska soils are comparatively less erosive. This extension circular covers factors which influence erosion, erosion control practices, and storage of soil moisture.

EC38-118 Soil and Moisture Conservation in Nebraska

When the white men first explored Nebraska, they found little erosion taking place. They found the hills, particularly in eastern Nebraska, covered with a dense growth of grass, underlain with a thick mat of decaying debris. The valleys were even more densely covered with the water-loving grasses and sedges. The soil underneath and prairie was black and soggy, the result of centuries of accumulating humus. The valleys bordernig the streams were boggy and abounded with springs. Clear water flowed constantly in the streams. The upland draws in the more favorable parts of the state were heavily covered with the big bluesteam and slough grass. Springs occurred in many of these. Soil erosion in Nebraska has not progressed to as great an extent as in states to the east and to the south. This is because of the comparatively lower rainfall in Nebraska, because the land has been farmed for fewer years in this state, and because some Nebraska soils are comparatively less erosive. This extension circular covers the factors which influence erosion, erosion control practices and storage of soil moisture.

Aerial Rivers and Lakes: Looking at Large-Scale Moisture Transport and Its Relation to Amazonia and to Subtropical Rainfall in South America

This is an observational study of the large-scale moisture transport over South America, with some analyses on its relation to subtropical rainfall. The concept of aerial rivers is proposed as a framework: it is an analogy between the main pathways of moisture flow in the atmosphere and surface rivers. Opposite to surface rivers, aerial rivers gain (lose) water through evaporation (precipitation). The magnitude of the vertically integrated moisture transport is discharge, and precipitable water is like the mass of the liquid column-multiplied by an equivalent speed it gives discharge. Trade wind flow into Amazonia, and the north/northwesterly flow to the subtropics, east of the Andes, are aerial rivers. Aerial lakes are the sections of a moisture pathway where the flow slows down and broadens, because of diffluence, and becomes deeper, with higher precipitable water. This is the case over Amazonia, downstream of the trade wind confluence. In the dry season, moisture from the aerial lake is transported northeastward, but weaker flow over southern Amazonia heads southward toward the subtropics. Southern Amazonia appears as a source of moisture to this flow. Aerial river discharge to the subtropics is comparable to that of the Amazon River. The variations of the amount of moisture coming from Amazonia have an important effect over the variability of discharge. Correlations between the flow from Amazonia and subtropical rainfall are not strong. However, some months within the set of dry seasons observed showed a strong increase (decrease) occurring together with an important increase (decrease) in subtropical rainfall.

Influence of moisture and plaque on the performance of a laser fluorescence device in detecting caries lesions in primary teeth

The aim of this study was to evaluate the influence of dental plaque and moisture on performance of a laser fluorescence device in detecting occlusal and proximal caries lesions in primary teeth. Fifty-five occlusal and 58 proximal sites on primary molars were evaluated using a DIAGNOdent pen (LFpen) device. For the drying time study, the evaluations were performed in: (I) moist teeth; (II) teeth dried for 3 s, or (III) dried for 15 s. For the plaque study, the evaluations were done in sites: (I) without plaque; (II) with plaque, and (III) after cleaning. Evaluation of the teeth sections in stereomicroscope was the reference standard method. LF pen values, sensitivity, specificity, and accuracy were compared. The values obtained after 15 s of drying were higher than those obtained with moist teeth or dried for 3 s at both occlusal and proximal surfaces. However, there was no change in the performance in detecting caries lesions. With regard to the presence of plaque, there was no significant change in the readings of the device, but specificity was decreased in occlusal surfaces with plaque. At proximal surfaces, however, no significant differences were observed. In conclusion, the moisture conditions do not influence significantly the performance of the LFpen, but the presence of plaque can affect its performance in detecting occlusal caries lesions in primary teeth.

Effects of Different Moisture Contents on Physical Properties of PVA-Gelatin Films

In this work, it was investigated the effect of different moisture contents on PVA-gelatin films by means of dielectric properties, infrared spectroscopy, microwave response and gravimetric method. The films were elaborated from a blend of gelatin and PVA, with 0 and 25 % glycerol. The sorption isotherms were determined by gravimetric methods, at 25 A degrees C. A capacimeter was used for dielectric measurements, and a device called SOLFAN setup was used for microwave measurements. The sorption isotherms were markedly affected by the glycerol content and relative humidity, due to the hygroscopic nature of the films. The dielectric constant and the microwave response signal were also strongly affected by the moisture and glycerol content in the films. Finally, Infrared spectra showed some changes in the amide peak positions, attributed to the modifications in the interactions between the macromolecules. The behaviors obtained in this work were explained on the basis the way the water enters in the film matrix.

Response surface methodology (RSM) to evaluate moisture effects on corn stover in recovering xylose by DEO hydrolysis

Response surface methodology (RSM), based on a 2(2) full factorial design, evaluated the moisture effects in recovering xylose by diethyloxalate (DEO) hydrolysis. Experiments were carried out in laboratory reactors (10 mL glass ampoules) containing corn stover (0.5 g) properly ground. The ampoules were kept at 160 degrees C for 90 min.(-) Both DEO concentration and corn stover moisture content were statistically significant at 99% confidence level. The maximum xylose recovery by the response surface methodology was achieved employing both DEO concentration and corn stover moisture at near their highest levels area. We amplified this area by using an overlay plot as a graphical optimization using a response of xylose recovery more than 80%. The mathematical statistical model was validated by testing a specific condition in the satisfied overlay plot area. Experimentally, a maximum xylose recovery (81.2%) was achieved by using initial corn stover moisture of 60% and a DEO concentration of 4% w/w. The mathematical statistical model showed that xylose recovery increases during DEO corn stover acid hydrolysis as the corn stover moisture level increases. This observation could be important during the harvesting of corn before it is fully dried in the field. The corn stover moisture was an important variable to improve xylose recovery by DEO acid hydrolysis. (c) 2011 Elsevier Ltd. All rights reserved.

Effects of moisture content on structural and dielectric properties of cassava starch films

In this work, it was evaluated the effect of moisture content on the structural and dielectric properties of cassava starch films by means of Fourier Transform infrared spectroscopy (FTIR), impedancimetric, and gravimetric analysis. The film samples were equilibrated in hermetically sealed desiccators, containing different saturated salts in water in order to promote activity of water between 0.11 and 0.85. The position and amplitude of the peaks in the fingerprint region of the FTIR spectra were changed due to the modifications in the interactions between the polymeric chains and water molecules. These effects may be related to the formation of semi-crystalline regions in the film structure. The dielectric properties of the films were also strongly dependent on the moisture content, showing a non-linear and a linear region, which was attributed to the domain of bound and free water in the film, respectively. The gravimetric analyzes showed the typical sigmoidal behavior, attributed to the way the water interacts with the biopolymer. Finally, the flexibility of the films increased with water content increasing.

Effect of heat and moisture exchangers on the prevention of ventilator-associated pneumonia in critically ill patients

Ventilator-associated pneumonia (VAP) remains one of the major causes of infection in the intensive care unit (ICU) and is associated with the length of hospital stay, duration of mechanical ventilation, and use of broad-spectrum antibiotics. We compared the frequency of VAP 10 months prior to (pre-intervention group) and 13 months after (post-intervention group) initiation of the use of a heat and moisture exchanger (HME) filter. This is a study with prospective before-and-after design performed in the ICU in a tertiary university hospital. Three hundred and fourteen patients were admitted to the ICU under mechanical ventilation, 168 of whom were included in group HH (heated humidifier) and 146 in group HME. The frequency of VAP per 1000 ventilator-days was similar for both the HH and HME groups (18.7 vs 17.4, respectively; P = 0.97). Duration of mechanical ventilation (11 vs 12 days, respectively; P = 0.48) and length of ICU stay (11 vs 12 days, respectively; P = 0.39) did not differ between the HH and HME groups. The chance of developing VAP was higher in patients with a longer ICU stay and longer duration of mechanical ventilation. This finding was similar when adjusted for the use of HME. The use of HME in intensive care did not reduce the incidence of VAP, the duration of mechanical ventilation, or the length of stay in the ICU in the study population.

Surface ecophysiological behavior across vegetation and moisture gradients in tropical South America

Surface ecophysiology at five sites in tropical South America across vegetation and moisture gradients is investigated. From the moist northwest (Manaus) to the relatively dry southeast (Pé de Gigante, state of São Paulo) simulated seasonal cycles of latent and sensible heat, and carbon flux produced with the Simple Biosphere Model (SiB3) are confronted with observational data. In the northwest, abundant moisture is available, suggesting that the ecosystem is light-limited. In these wettest regions, Bowen ratio is consistently low, with little or no annual cycle. Carbon flux shows little or no annual cycle as well; efflux and uptake are determined by high-frequency variability in light and moisture availability. Moving downgradient in annual precipitation amount, dry season length is more clearly defined. In these regions, a dry season sink of carbon is observed and simulated. This sink is the result of the combination of increased photosynthetic production due to higher light levels, and decreased respiratory efflux due to soil drying. The differential response time of photosynthetic and respiratory processes produce observed annual cycles of net carbon flux. In drier regions, moisture and carbon fluxes are in-phase; there is carbon uptake during seasonal rains and efflux during the dry season. At the driest site, there is also a large annual cycle in latent and sensible heat flux.

Potential vorticity and moisture in extratropical cyclones : climatology and sensitivity experiments

The development of extratropical cyclones can be seen as an interplay of three positive potential vorticity (PV) anomalies: an upper-level stratospheric intrusion, low-tropospheric diabatically produced PV, and a warm anomaly at the surface acting as a surrogate PV anomaly. In the mature stage they become vertically aligned and form a “PV tower” associated with strong cyclonic circulation. This paradigm of extratropical cyclone development provides the basis of this thesis, which will use a climatological dataset and numerical model experiments to investigate the amplitude of the three anomalies and the processes leading in particular to the formation of the diabatically produced low-tropospheric PV anomaly.rnrnThe first part of this study, based on the interim ECMWF Re-Analysis (ERA-Interim) dataset, quantifies the amplitude of the three PV anomalies in mature extratropical cyclones in different regions in the Northern Hemisphere on a climatological basis. A tracking algorithm is applied to sea level pressure (SLP) fields to identify cyclone tracks. Surface potential temperature anomalies ∆θ and vertical profiles of PV anomalies ∆PV are calculated at the time of the cyclones’ minimum SLP and during the intensification phase 24 hours before in a vertical cylinder with a radius of 200 km around the surface cyclone center. To compare the characteristics of the cyclones, they are grouped according to their location (8 regions) and intensity, where the central SLP is used as a measure of intensity. Composites of ∆PV profiles and ∆θ are calculated for each region and intensity class at the time of minimum SLP and during the cyclone intensification phase.rnrnDuring the cyclones’ development stage the amplitudes of all three anomalies increase on average. In the mature stage all three anomalies are typically larger for intense than for weak winter cyclones [e.g., 0.6 versus 0.2 potential vorticity units (PVU) at lower levels, and 1.5 versus 0.5 PVU at upper levels].rnThe regional variability of the cyclones’ vertical structure and the profile evolution is prominent (cyclones in some regions are more sensitive to the amplitude of a particular anomaly than in other regions). Values of ∆θ and low-level ∆PV are on average larger in the western parts of the oceans than in the eastern parts. In addition, a large seasonal variability can be identified, with fewer and weaker cyclones especially in the summer, associated with higher low-tropospheric PV values, but also with a higher tropopause and much weaker surface potential temperature anomalies (compared to winter cyclones).rnrnIn the second part, we were interested in the diabatic low-level part of PV towers. Evaporative sources were identified of moisture that was involved in PV production through condensation. Lagrangian backward trajectories were calculated from the region with high PV values at low-levels in the cyclones. PV production regions were identified along these trajectories and from these regions a new set of backward trajectories was calculated and moisture uptakes were traced along them. The main contribution from surface evaporation to the specific humidity of the trajectories is collected 12-72 hours prior to therntime of PV production. The uptake region for weaker cyclones with less PV in the centre is typically more localized with reduced uptake values compared to intense cyclones. However, in a qualitative sense uptakes and other variables along single trajectories do not vary much between cyclones of different intensity in different regions.rnrnA sensitivity study with the COSMO model comprises the last part of this work. The study aims at investigating the influence of synthetic moisture modification in the cyclone environment in different stages of its development. Moisture was eliminated in three regions, which were identified as important moisture source regions for PV production. Moisture suppression affected the cyclone the most in its early phase. It led to cyclolysis shortly after its genesis. Nevertheles, a new cyclone formed on the other side of a dry box and developed relatively quickly. Also in other experiments, moisture elimination led to strong intensity reduction of the surface cyclone, limited upper-level development, and delayed or missing interaction between the two.rnrnIn summary, this thesis provides novel insight into the structure of different intensity categories of extratropical cyclones from a PV perspective, which corroborates the findings from a series of previous case studies. It reveals that all three PV anomalies are typically enhanced for more intense cyclones, with important regional differences concerning the relative amplitude of the three anomalies. The moisture source analysis is the first of this kind to study the evaporation-condensation cycle related to the intensification of extratropical cyclones. Interestingly, most of the evaporation occurs during the 3 days prior to the time of maximum cyclone intensity and typically extends over fairly large areas along the track of the cyclone. The numerical model case study complements this analysis by analyzing the impact of regionally confined moisture sources for the evolution of the cyclone.