A biomechanical analysis of growing rods used in the management of early onset scoliosis

INTRODUCTION Managing spinal deformities in young children is challenging, particularly early onset scoliosis (EOS). Surgical intervention is often required if EOS has been unresponsive to conservative treatment particularly with rapidly progressive curves. An emerging treatment option for EOS is fusionless scoliosis surgery. Similar to bracing, this surgical option potentially harnesses growth, motion and function of the spine along with correcting spinal deformity. Dual growing rods are one such fusionless treatment, which aims to modulate growth of the vertebrae. The aim of this study was to ascertain the extent to which semiconstrained growing rods (Medtronic, Sofamor, Danek, Memphis, TN) with a telescopic sleeve component, reduce rotational constraint on the spine compared with standard "constrained / rigid" rods and hence potentially provide a more physiological mechanical environment for the growing spine. METHODS Six 40-60kg English Large White porcine spines served as a model for the paediatric human spine. Each spine was dissected into a 7 level thoracolumbar multi-segment unit (MSU), removing all non-ligamentous soft tissues and leaving 3cm of ribs either side. Pure nondestructive axial rotation moments of ±4Nm at a constant rotation rate of 8deg.s-1 were applied to the mounted MSU spines using a biaxial Instron testing machine. Displacement of each vertebral level was captured using a 3D motion tracking system (Optotrak 3020, Northern Digital Inc, Waterloo, ON). Each spine was tested in an un-instrumented state first and then with appropriately sized semi-constrained growing rods and rigid rods in alternating sequence. The rods were secured by multi-axial pedicle screws (Medtronic CD Horizon) at levels 2 and 6 of the construct. The range of motion (ROM), neutral zone (NZ) size and stiffness (Nm.deg-1) were calculated from the Instron load-displacement data and intervertebral ROM was calculated through a MATLAB algorithm from Optotrak data. RESULTS Irrespective of the order of testing, rigid rods significantly reduced the total ROM compared with semi-constrained rods (p<0.05) with in a significantly stiffer spine for both left and right axial rotation (p<0.05). Analysing the intervertebral motion within the instrumented levels 2-6, rigid rods showed reduced ROM compared with semi-constrained growing rods and compared with un-instrumented motion segments. CONCLUSION Semi-constrained growing rods maintain similar stiffness in axial rotation to un-instrumented spines, while dual rigid rods significantly reduce axial rotation. Clinically the effect of semi-constrained growing rods as observed in this study is that they would be expected to allow growth via the telescopic rod components while maintaining the axial flexibility of the spine, which may reduce occurrence of the crankshaft phenomenon.

Thoracoscopic scoliosis surgery – a cheaper option? A cost analysis of 189 consecutive cases

INTRODUCTION: Increasing health care costs, limited resources and increased demand makes cost effective and cost-efficient delivery of Adolescent Idiopathic Scoliosis (AIS) management paramount. Rising implant costs in deformity correction surgery have prompted analysis of whether high implant densities are justified. The objective of this study was to analyse the costs of thoracoscopic scoliosis surgery, comparing initial learning curve costs with those of the established technique and to the costs involved in posterior instrumented fusion from the literature. METHODS: 189 consecutive cases from April 2000 to July 2011 were assessed with a minimum of 2 years follow-up. Information was gathered from a prospective database covering perioperative factors, clinical and radiological outcomes, complications and patient reported outcomes. The patients were divided into three groups to allow comparison; 1. A learning curve cohort, 2. An intermediate cohort and 3. A third cohort of patients, using our established technique. Hospital finance records and implant manufacturer figures were corrected to 2013 costs. A literature review of AIS management costs and implant density in similar curve types was performed. RESULTS: The mean pre-op Cobb angle was 53°(95%CI 0.4) and was corrected postop to mean 22.9°(CI 0.4). The overall complication rate was 20.6%, primarily in the first cohort, with a rate of 5.6% in the third cohort. The average total costs were $46,732, operating room costs of $10,301 (22.0%) and ICU costs of $4620 (9.8%). The mean number of screws placed was 7.1 (CI 0.04) with a single rod used for each case giving average implant costs of $14,004 (29.9%). Comparison of the three groups revealed higher implant costs as the technique evolved to that in use today, from $13,049 in Group 1 to $14577 in Group 3 (P<0.001). Conversely operating room costs reduced from $10,621 in Group 1 to $7573 (P<0.001) in Group 3. ICU stay was reduced from an average of 1.2 to 0 days. In-patient stay was significantly (P=0.006) lower in Groups 2 and 3 (5.4 days) than Group 1 (5.9 days) (i.e. a reduction in cost of approximately $6,140). CONCLUSIONS: The evolution of our thoracoscopic anterior scoliosis correction has resulted in an increase in the number of levels fused and reduction in complication rate. Implant costs have risen as a result, however, there has been a concurrent decrease in those costs generated by operating room use, ICU and in-patient stay with increasing experience. Literature review of equivalent curve types treated posteriorly shows similar perioperative factors but higher implant density, 69-83% compared to the 50% in this study. Thoracoscopic Scoliosis surgery presents a low density, reliable, efficient and effective option for selected curves. A cost analysis of Thoracoscopic Scoliosis Surgery using financial records and a prospectively collected database of all patients since 2000, demonstrating a clear cost advantage compared to equivalent posterior instrumentation and fusion.

The stabilising role of the costovertebral joints and spinous processes on thoracic spine stability

Introduction The importance of in vitro biomechanical testing in today’s understanding of spinal pathology and treatment modalities cannot be stressed enough. Different studies have used differing levels of dissection of their spinal segments for their testing protocols[1, 2]. The aim of this study was to assess the impact of removing the costovertebral joints and partial resection of the spinous process sequentially, on the stiffness of the immature thoracic bovine spinal segment. Materials and Methods Thoracic spines from 6-8 week old calves were used. Each spine was dissected and divided into motion segments with 5cm of attached rib on each side and full spinous processes including levels T4-T11 (n=28). They were potted in polymethylemethacrylate. An Instron Biaxial materials testing machine with a custom made jig was used for testing. The segments were tested in flexion/extension, lateral bending and axial rotation at 37⁰C and 100% humidity, using moment control to a maximum 1.75 Nm with a loading rate of 0.3 Nm per second. They were first tested intact for ten load cycles with data collected from the tenth cycle. Progressive dissection was performed by removing first the attached ribs, followed by the spinous process at its base. Biomechanical testing was carried out after each level of dissection using the same protocol. Statistical analysis of the data was performed using repeated measures ANOVA. Results In combined flexion/extension there was a significant reduction in stiffness of 16% (p=0.002). This was mainly after resection of the ribs (14%, p=0.024) and mainly occurred in flexion where stiffness reduced by 22% (p=0.021). In extension, stiffness dropped by 13% (p=0.133). However there was no further significant change in stiffness on resection of the spinous process (<1%) (p=1.00). In lateral bending there was a significant decrease in stiffness of 13% (p<0.001). This comprised a drop of 11% on resection of the ribs (p=0.009) and a further 8% on resection of the spinous process (p=0.014). There was no difference between left and right bending. In axial rotation there was no significant change in stiffness after each stage of dissection (p=0.253). There was no difference between left and right rotation. Conclusion The costovertebral joints play a significant role in providing stability to the bovine thoracic spine in both flexion/extension and lateral bending, whereas the spinous processes play a minor role. Both elements have little effect on axial rotation stability.

The implications of de‐collectivist industrial relations laws and associated developments for worker health and safety in Australia, 1996–2007

The institutional and regulatory interlinkages between industrial relations (IR) and occupational health and safety (OHS) are seldom explored in the IR literature. This article begins to address this gap by examining regulatory initiatives in Australia during a period of neoliberal government. It examines the laws enacted by the federal government during this period and events and cases arising from these laws that go some way to illustrating their effects. Evidence is also drawn from detailed research on a number of state OHS inspectorates between 2004 and 2006. It is argued that de-collectivist changes to IR laws exacerbated problems posed by the growth of flexible work arrangements and a drop in union density, weakening participatory provisions in OHS laws and promoting work arrangements that undermined OHS standards. The study provides evidence of the implications of a divergence in the trajectory of IR and OHS laws and the importance of better integrating worker protection laws.

The court and the factory the legal construction of occupational health and safety offences in Victoria

This thesis reports on an empirically based study of the manner in which Victorian Magistrates Courts constructed occupational health and safety (OHS) issues when hearing prosecutions for offences under the Industrial Safety, Health and Welfare Act 1981 (the ISHWA) and the Occupational Health and Safety Act 1985 (OHSA) from 1983 to 1991. These statutes established OHS standards for employers and other relevant parties. The State government enforced these standards through an OHS inspectorate which had a range of enforcement powers, including prosecution. After outlining the historical development of Victoria’s OHS legislation, the magistracy’s historical role in its enforcement, and the development of an enforcement culture in which inspectors viewed prosecution as a last resort, the study shows how the key provisions of the ISHWA and OHSA required occupiers of workplaces and employers to provide and maintain safe systems of work, including the guarding of dangerous machinery. Using a wide range of empirical research methods and legal materials, it shows how the enforcement policies, procedures and practices of the inspectorate heavily slanted inspectors workplace investigations and hence prosecutions towards a restricted and often superficial, analysis of incidents (or “events”) most of which involved injuries on machinery. There was evidence, however, that after the establishment of the Central Investigation Unit in 1989 cases were more thoroughly investigated and prosecuted. From 1990 the majority of prosecutions were taken under the employer’s general duty provisions, and by 1991 there was evidence that prosecutions were focusing on matters other than machinery guarding.

Measurement of actual efficacy of compact fluorescent lamps (CFLs)

The use of compact fluorescent lamps (CFLs) in domestic residences has increased rapidly due to their higher energy efficiency and longer life expectancy when compared with traditional incandescent light bulbs. Through measurement of illuminance, actual power and apparent power, the actual efficacy and associated power factor of CFLs are studied in this paper. It is found that for an individual CFL, although its power consumption and lighting output (i.e. luminous flux) may be higher or lower than the stated values provided by the lighting manufacturers, the actual efficacy would most likely be equal to or better than the efficacy calculated from the given rated power and lumen from the manufacturers. The typical power factor for CFLs was 0.63.

Strength properties of composite clay balls containing additives from industry wastes as new filter media in water treatment

Pebble matrix filtration (PMF) is a water treatment technology that can remove suspended solids in highly turbid surface water during heavy storms. PMF typically uses sand and natural pebbles as filter media. Hand-made clay pebbles (balls) can be used as alternatives to natural pebbles in PMF treatment plants, where natural pebbles are not readily available. Since the high turbidity is a seasonal problem that occurs during heavy rains, the use of newly developed composite clay balls instead of pure clay balls have the advantage of removing other pollutants such as natural organic matter (NOM) during other times. Only the strength properties of composite clay balls are described here as the pollutant removal is beyond the scope of this paper. These new composite clay balls must be able to withstand dead and live loads under dry and saturated conditions in a filter assembly. Absence of a standard ball preparation process and expected strength properties of composite clay balls were the main reasons behind the present study. Five different raw materials from industry wastes: Red Mud (RM), Water Treatment Alum Sludge (S), Shredded Paper (SP), Saw Dust (SD), and Sugar Mulch (SM) were added to common clay brick mix (BM) in different proportions. In an effort to minimize costs, in this study clay balls were fired to 1100 0C at a local brick factory together with their bricks. A comprehensive experimental program was performed to evaluate crushing strength of composite hand-made clay balls, using uniaxial compression test to establish the best material combination on the basis of strength properties for designing sustainable filter media for water treatment plants. Performance at both construction and operating stages were considered by analyzing both strength properties under fully dry conditions and strength degradation after saturation in a water bath. The BM-75% as the main component produced optimum combination in terms of workability and strength. With the material combination of BM-75% and additives-25%, the use of Red Mud and water treatment sludge as additives produced the highest and lowest strength of composite clay balls, with a failure load of 5.4 kN and 1.4 kN respectively. However, this lower value of 1.4 kN is much higher than the effective load on each clay ball of 0.04 kN in a typical filter assembly (safety factor of 35), therefore, can still be used as a suitable filter material for enhanced pollutant removal.

Prevalence of refractive errors among schoolchildren in Shiraz, Iran

PURPOSE To determine the prevalence of refractive errors in Shiraz schoolchildren by age and gender. METHODS For this cross-sectional study, random cluster sampling was carried out from students of the 2008-2009 academic year. After the initial interview, ophthalmic examinations including tests of visual acuity, non-cycloplegic and cycloplegic refraction and binocular vision were performed. Myopia was defined as a spherical equivalent < or =-0.50 dioptre (D), hyperopia as > or =+2.0 D, and astigmatism as a cylinder refraction > or =0.75 D. All values for school grade and gender were directly standardized based on the total student population in the 2008-2009 school year. RESULTS A total of 2130 students were sampled, of which 1872 participated in the study (response rate = 87.88%). The prevalence of uncorrected, best-corrected, presenting and spectacle corrected visual acuity of 6/12 or worse in the better eye was 6.46%, 0%, 1.49% and 0.9%, respectively. The prevalence rates of myopia, hyperopia and astigmatism were 4.35% (95% confidence interval [CI]: 2.89-5.82%), 5.04% (95% CI: 3.50-6.58%), and 11.27% (95% CI: 9.81-12.74%), respectively. Anisometropia was detected in 2.58% of schoolchildren. The prevalence of hyperopia significantly decreased with age (P = 0.021). CONCLUSIONS Compared with other reported rates, the prevalence of myopia in the schoolchildren of Shiraz is similar to that in most places excluding East Asian countries, and that of hyperopia is in the mid range.

Assessment of fundamental movement skills in childhood cancer patients

Background The improved treatment protocols and subsequent improved survival rates amongst childhood cancer patients has shifted the focus towards the long-term consequences arising from cancer treatment. Children who have completed cancer treatment are at a greater risk of delayed development, diminished functioning, disability, compromised fundamental movement skill (FMS) attainment and long term chronic health conditions. The aim of the study was to compare FMS of childhood cancer patients with an aged matched healthy reference group. Methods Pediatric cancer patients aged 5-8 years of age (n=26; median age 6.91 years), who completed cancer treatment (<5 years) at the Sydney Children’s Hospital were assessed performing 7 key FMS; sprint, side-gallop, vertical-jump, catch, over-arm throw, kick and leap. Results were compared to the reference group (n=430; 6.56 years). Results Childhood cancer patients scored significantly lower on 3 out of 7 FMS tests when compared to the reference group. These results equated to a significantly lower overall score for FMS. Conclusion This study highlighted the significant deficits in FMS within pediatric patients having completed cancer treatment. In order to reduce the occurrence of significant FMS deficits in this population, FMS interventions maybe warranted to assist in recovery from childhood cancer, prevent late effects and improve the quality of life in survivors of childhood cancer.

Influence of pipe length and flow rate on nano-particle deposition in laminar circular pipe flows

The Lagrangian particle tracking provides an effective method for simulating the deposition of nano- particles as well as micro-particles as it accounts for the particle inertia effect as well as the Brownian excitation. However, using the Lagrangian approach for simulating ultrafine particles has been limited due to computational cost and numerical difficulties. The aim of this paper is to study the deposition of nano-particles in cylindrical tubes under laminar condition using the Lagrangian particle tracking method. The commercial Fluent software is used to simulate the fluid flow in the pipes and to study the deposition and dispersion of nano-particles. Different particle diameters as well as different pipe lengths and flow rates are examined. The results show good agreement between the calculated deposition efficiency and different analytic correlations in the literature. Furthermore, for the nano-particles with higher diameters and when the effect of inertia has a higher importance, the calculated deposition efficiency by the Lagrangian method is less than the analytic correlations based on Eulerian method due to statistical error or the inertia effect.

Building personas of students accessing a peer-facilitated support for learning program

The modern student represents a change from the traditional learner. More than ever before, additional resources are available online and yet personalised learning and peer-assistance programs are becoming an essential part of tertiary education delivery. This paper presents the first stage in a user-centred design approach to the analysis of the completeness and efficacy of such a personalised, peer-based support for learning program. This approach used an iterative design methodology based on contextual interview, workshops and focus groups to develop personas representing students visiting the program. Initial uses of these developed personas have included training of new personnel as well as the evaluation of the program. Overall the use of this user-centred approach and iterative persona development methodology has yielded an invaluable resource for the design of support for learning programs across the higher education industry within Australia and beyond.

Enhancing the performance of irrigated cotton and grain in Central Queensland

R&D to facilitate incorporation of grain and pulse crop phases in Central Queensland irrigated cotton monoculture systems and improve profitability of regional cropping systems.

Lucien Wolf and David Mowshowitch papers, [ca. 1869-1959]

Correspondence, reports, minutes, manuscripts, and clippings relating to the activities of Wolf, Mowshowitch, and the Joint Foreign Committee, as well as to the political situation of Jews in various countries and to the Paris Peace Conference. Papers of Lucien Wolf include his diary, lectures on English-German relations and English-Russian relations; bibliography of Wolf's works on Jewish themes; clippings of Wolf's articles; congratulations on his seventieth birthday; article on his last interview with Chamberlain; and correspondence with parents, 1869-1882, A. Abrahams, 1914-1925, Chief Rabbi Dr. J.H. Hertz, 1892-1923, Clara Melchior, 1913-1929, Jacob Schiff, 1910, Maxim Vinawer, 1917, Mark Wischnitzer, 1926-1928, Lord Robert Cecil, 1916-1919, Lord Rothschild, 1906, Cyrus Adler, Count J. Bernstorff, Szymon Ashkenazy, Solomon Dingol, Louis Marshall, Claude G. Montefiore, Sir Edward Sassoon, Jacob Schiff, Lord William Selborne, Nakhum Sokolow, Oscar Straus, Chaim Weizmann, the American Jewish Congress, 1916-1923, Hilfsverein der Deutschen Juden, 1913, and Jewish Historical Society of England.