903 resultados para Low cost airlines


Relevância:

100.00% 100.00%

Publicador:

Resumo:

The solar irradiation that a crop receives is directly related to the physical and biological processes that affect the crop. However, the assessment of solar irradiation poses certain problems when it must be measured through fruit inside the canopy of a tree. In such cases, it is necessary to check many test points, which usually requires an expensive data acquisition system. The use of conventional irradiance sensors increases the cost of the experiment, making them unsuitable. Nevertheless, it is still possible to perform a precise irradiance test with a reduced price by using low-cost sensors based on the photovoltaic effect. The aim of this work is to develop a low-cost sensor that permits the measurement of the irradiance inside the tree canopy. Two different technologies of solar cells were analyzed for their use in the measurement of solar irradiation levels inside tree canopies. Two data acquisition system setups were also tested and compared. Experiments were performed in Ademuz (Valencia, Spain) in September 2011 and September 2012 to check the validity of low-cost sensors based on solar cells and their associated data acquisition systems. The observed difference between solar irradiation at high and low positions was of 18.5% ± 2.58% at a 95% confidence interval. Large differences were observed between the operations of the two tested sensors. In the case of a-Si cells based mini-modules, an effect of partial shadowing was detected due to the larger size of the devices, the use of individual c-Si cells is recommended over a-Si cells based mini-modules.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Batteries and ultracapacitors for hybrid and electric vehicles must satisfy very demanding working conditions that are not usual in other applications. In this sense, specific tests must be performed in order to draw accurate conclusions about their behaviour. To do so, new advanced test benches are needed. These platforms must allow the study of a wide variety of energy storage systems under conditions similar to the real ones. In this paper, a flexible, low-cost and highly customizable system is presented. This system allows batteries and ultracapacitors to be tested in many and varied ways, effectively emulating the working conditions that they face in an electric vehicle. The platform was specifically designed to study energy storage systems for electric and hybrid vehicles, meaning that it is suitable to test different systems in many different working conditions, including real driving cycles. This flexibility is achieved keeping the cost of the platform low, which makes the proposed test bench a feasible alternative for the industry. As an example of the functionality of the platform, a test consisting of a 17-minute ARTEMIS urban cycle with a NiMH battery pack is presented.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

In this paper we present an adaptive spatio-temporal filter that aims to improve low-cost depth camera accuracy and stability over time. The proposed system is composed by three blocks that are used to build a reliable depth map of static scenes. An adaptive joint-bilateral filter is used to obtain consistent depth maps by jointly considering depth and video information and by adapting its parameters to different levels of estimated noise. Kalman filters are used to reduce the temporal random fluctuations of the measurements. Finally an interpolation algorithm is used to obtain consistent depth maps in the regions where the depth information is not available. Results show that this approach allows to considerably improve the depth maps quality by considering spatio-temporal information and by adapting its parameters to different levels of noise.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

In this paper we present a low-cost efficient Interactive Whiteboard that, by fusing depth and video information provided by a low-cost depth camera, is able to detect and track user movements.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

In this paper, we present a depth-color scene modeling strategy for indoors 3D contents generation. It combines depth and visual information provided by a low-cost active depth camera to improve the accuracy of the acquired depth maps considering the different dynamic nature of the scene elements. Accurate depth and color models of the scene background are iteratively built, and used to detect moving elements in the scene. The acquired depth data is continuously processed with an innovative joint-bilateral filter that efficiently combines depth and visual information thanks to the analysis of an edge-uncertainty map and the detected foreground regions. The main advantages of the proposed approach are: removing depth maps spatial noise and temporal random fluctuations; refining depth data at object boundaries, generating iteratively a robust depth and color background model and an accurate moving object silhouette.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

La ponencia presenta una comparación entre el rendimiento energético que se obtiene con un módulo fotovoltaico convencional, sin utilizar ningún medio para reducir la temperatura de sus células, y el rendimiento global que resulta si se incorpora a dicho módulo un intercambiador de calor en su parte trasera para reducir la temperatura de sus células y a la vez elevar la temperatura del agua proveniente de la red urbana de abastecimiento. El estudio muestra que el incremento de energia total que se logra mediante la solución propuesta supone una tasa de retorno con un plazo de amortización razonable para este tipo de instalaciones.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Dynamic measurements will become a standard for bridge monitoring in the near future. This fact will produce an important cost reduction for maintenance. US Administration has a long term intensive research program in order to diminish the estimated current maintenance cost of US$7 billion per year over 20 years. An optimal intervention maintenance program demands a historical dynamical record, as well as an updated mathematical model of the structure to be monitored. In case that a model of the structure is not actually available it is possible to produce it, however this possibility does not exist for missing measurement records from the past. Current acquisition systems to monitor structures can be made more efficient by introducing the following improvements, under development in the Spanish research Project “Low cost bridge health monitoring by ambient vibration tests using wireless sensors”: (a) a complete wireless system to acquire sensor data, (b) a wireless system that permits the localization and the hardware identification of the whole sensor system. The applied localization system has been object of a recent patent, and (c) automatization of the modal identification process, aimed to diminish human intervention. This system is assembled with cheap components and allows the simultaneous use of a large number of sensors at a low placement cost. The engineer’s intervention is limited to the selection of sensor positions, probably based on a preliminary FE analysis. In case of multiple setups, also the position of a number of fixed reference sensors has to be decided. The wireless localization system will obtain the exact coordinates of all these sensors positions. When the selection of optimal positions is difficult, for example because of the lack of a proper FE model, this can be compensated by using a higher number of measuring (also reference) points. The described low cost acquisition system allows the responsible bridge administration to obtain historical dynamic identification records at reasonable costs that will be used in future maintenance programs. Therefore, due to the importance of the baseline monitoring record of a new bridge, a monitoring test just after its construction should be highly recommended, if not compulsory.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

We propose and demonstrate a low-cost alternative scheme of direct-detection to detect a 100Gbps polarization-multiplexed differential quadrature phase-shift keying (PM-DQPSK) signal. The proposed scheme is based on a delay line and a polarization rotator; the phase-shift keying signal is first converted into a polarization shift keying signal. Then, this signal is converted into an intensity modulated signal by a polarization beam splitter. Finally, the intensity-modulated signal is detected by balanced photodetectors. In order to demonstrate that our proposed receiver is suitable for using as a PM-DQPSK demodulator, a set of simulations have been performed. In addition to testing the sensitivity, the performance under various impairments, including narrow optical filtering, polarization mode dispersion, chromatic dispersion and polarization sensitivity, is analyzed. The simulation results show that our performance receiver is as good as a conventional receiver based on four delay interferometers. Moreover, in comparison with the typical receiver, fewer components are used in our receiver. Hence, implementation is easier, and total cost is reduced. In addition, our receiver can be easily improved to a bit-rate tunable receiver.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

This paper presents a communication interface between supervisory low-cost mobile robots and domestic Wireless Sensor Network (WSN) based on the Zig Bee protocol from different manufacturers. The communication interface allows control and communication with other network devices using the same protocol. The robot can receive information from sensor devices (temperature, humidity, luminosity) and send commands to actuator devices (lights, shutters, thermostats) from different manufacturers. The architecture of the system, the interfaces and devices needed to establish the communication are described in the paper.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Presentación en poster de impresión 3D de guias de onda.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Smart and green cities are hot topics in current research because people are becoming more conscious about their impact on the environment and the sustainability of their cities as the population increases. Many researchers are searching for mechanisms that can reduce power consumption and pollution in the city environment. This paper addresses the issue of public lighting and how it can be improved in order to achieve a more energy efficient city. This work is focused on making the process of turning the streetlights on and off more intelligent so that they consume less power and cause less light pollution. The proposed solution is comprised of a radar device and an expert system implemented on a low-cost platform based on a DSP. By analyzing the radar echo in both the frequency and time domains, the system is able to detect and identify objects moving in front of it. This information is used to decide whether or not the streetlight should be turned on. Experimental results show that the proposed system can provide hit rates over 80%, promising a good performance. In addition, the proposed solution could be useful in kind of other applications such as intelligent security and surveillance systems and home automation.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Throughout history, humans have cyclically return to their old traditions such as the organic orchards. Nowadays, these have been integrated into the modern cities and could supply fresh vegetables to the daily food improving human health. Organic orchards grow crops without pesticides and artificial fertilizers thus, they are respectful with the environment and guarantee the food's safety . In modern society, the application of new technology is a must, in this case to obtain an efficient irrigation. In order to monitor a proper irrigation and save water and energy, soil water content probes are used to measure soil water content. Among them, capacitive probes ,monitored with a specific data logger, are typically used. Most of them, specially the data loggers, are expensive and in many cases are not used. In this work, we have applied the open hardware Arduino to build and program a low cost datalogger for the programming of irrigation in an experimental organic orchard. Results showed that the application of such as low cost technology, which is easily available in the market and easy to understand, everyone can built and program its own device helping in managing water resources in organic orchards .

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The early detection of spoiling metabolic products in contaminated food is a very important tool to control quality. Some volatile compounds produce unpleasant odours at very low concentrations, making their early detection very challenging. This is the case of 1,3-pentadiene produced by microorganisms through decarboxylation of the preservative sorbate. In this work, we have developed a methodology to use the data produced by a low-cost, compact MWIR (Mid-Wave IR) spectrometry device without moving parts, which is based on a linear array of 128 elements of VPD PbSe coupled to a linear variable filter (LVF) working in the spectral range between 3 and 4.6 ?m. This device is able to analyze food headspace gases through dedicated sample presentation setup. This methodology enables the detection of CO2 and the volatile compound 1,3-pentadiene, as compared to synthetic patrons. Data analysis is based on an automated multidimensional dynamic processing of the MWIR spectra. Principal component and discriminant analysis allow segregating between four yeast strains including producers and no producers. The segregation power is accounted as a measure of the discrimination quality.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

An automated oligonucleotide synthesizer has been developed that can simultaneously and rapidly synthesize up to 96 different oligonucleotides in a 96-well microtiter format using phosphoramidite synthesis chemistry. A modified 96-well plate is positioned under reagent valve banks, and appropriate reagents are delivered into individual wells containing the growing oligonucleotide chain, which is bound to a solid support. Each well has a filter bottom that enables the removal of spent reagents while retaining the solid support matrix. A seal design is employed to control synthesis environment and the entire instrument is automated via computer control. Synthesis cycle times for 96 couplings are < 11 min, allowing a plate of 96 20-mers to be synthesized in < 5 hr. Oligonucleotide synthesis quality is comparable to commercial machines, with average coupling efficiencies routinely > 98% across the entire 96-well plate. No significant well-to-well variations in synthesis quality have been observed in > 6000 oligonucleotides synthesized to date. The reduced reagent usage and increased capacity allow the overall synthesis cost to drop by at least a factor of 10. With the development of this instrument, it is now practical and cost-effective to synthesize thousands to tens of thousands of oligonucleotides.