Estudo das propriedades físico-químicas do biodiesel e suas influências na deterioração dos elastômeros aplicados no sistema de injeção dos motores diesel

The biodiesel use has become important due to its renewable character and to reduce environmental impacts during the fuel burning. Theses benefit will be valid if the fuel shows good performance, chemistry stability and compatibility with engines. Biodiesel is a good fuel to diesel engines due to its lubricity. Then, the aimed of this study was to verify the physicalchemistry properties of biodiesel and their correlations with possible elastomers damage after biodiesel be used as fuel in an injection system. The methodology was divided in three steps: biodiesels synthesis by transesterification of three vegetable oil (soybean, palm and sunflower) and their physical-chemistry characterization (viscosity, oxidative stability, flash point, acidity, humidity and density); pressurized test of compatibility between elastomers (NBR and VITON) and biodiesel, and the last one, analyze of biodiesels lubricity by tribological test ball-plan( HFRR). Also, the effect of mixture of biodiesel and diesel in different concentrations was evaluated. The results showed that VITON showed better compatibility with all biodiesel blends in relation to NBR, however when VITON had contact with sunflower biodiesel and its blends the swelling degree suffer higher influences due to biodiesel humidity. For others biodiesels and theirs blends, this elastomer kept its mechanical properties constant. The better tribological performance was observed for blends with high biodiesel concentration, lower friction coefficient was obtained when palm biodiesel was used. The main mechanisms observed during the HFRR tests were abrasive and oxidative wear

Remoção de óleo da água de produção por flotação em coluna utilizando tensoativos de origem vegetal

In the petroleum industry, water is always present in the reservoir formation together with petroleum and natural gas and this fact provokes the production of water with petroleum, resulting in a great environmental impact. Several methods can be applied for treatment of oily waters, such as: gravitational vases, granulated media filtration systems, flotation process, centrifugation process and the use of hydrocyclones, which can also be used in a combined way. However, the flotation process has showed a great efficiency as compared with other methods, because these methods do not remove great part of the emulsified oil. In this work was investigated the use of surfactants derived from vegetable oils, OSS and OGS, as collectors, using the flotation process in a glass column with a porous plate filter in its base for the input of the gaseous steam. For this purpose, oil/water emulsions were prepared using mechanical stirring, with concentrations around 300 ppm. The air flow rate was set at 700 cm3/min and the porous plate filter used for the generation of the air bubbles has pore size varying from 16 to 40 Pm. The column operated at constant volume (1500mL). A new methodology has been developed to collect the samples, where, instead of collecting the water phase, it was collected the oil phase removed by the process in the top of the flotation column. It has been observed that it is necessary to find an optimum surfactant concentration to achieve enhanced removal efficiency. Being for OSS 1.275 mmol/L and for OGS 0.840 mmol/L, with removal efficiencies of 93% and 99%, respectively, using synthetic solutions. For the produced water, the removal in these concentrations was 75% for OSS and 65% for OGS. It is possible to remove oil from water in a flotation process using surfactants of high HLB, fact that is against the own definition of HLB (Hydrophile-Lipophile Balance). The interfacial tension is an important factor in the oil removal process using a flotation process, because it has direct interference in the coalescence of the oil drops. The spreading of the oil of the air bubble should be considered in the process, and for the optimum surfactant concentrations it reached a maximum value. The removal kinetics for the flotation process using surfactants in the optimum concentration has been adjusted according to a first order model, for synthetic water as for the produced water.

Avaliação da remoção de sulfeto de hidrogênio do gás natural em uma coluna de absorção

Natural gas, although basically composed by light hydrocarbons, also presents in its composition gaseous contaminants such as CO2 (carbon dioxide) and H2S (hydrogen sulfide). Hydrogen sulfide, which commonly occurs in oil and gas exploration and production activities, besides being among the gases that are responsible by the acid rain and greenhouse effect, can also cause serious harm to health, leading even to death, and damages to oil and natural gas pipelines. Therefore, the removal of hydrogen sulfide will significantly reduce operational costs and will result in oil with best quality to be sent to refinery, thereby resulting in economical, environmental, and social benefits. These factors highlight the need for the development and improvement of hydrogen sulfide sequestrating agents to be used in the oil industry. Nowadays there are several procedures for hydrogen sulfide removal from natural gas used by the petroleum industry. However, they produce derivatives of amines that are harmful to the distillation towers, form insoluble precipitates that cause pipe clogging and produce wastes of high environmental impact. Therefore, the obtaining of a stable system, in inorganic or organic reaction media, that is able to remove hydrogen sulfide without forming by-products that affect the quality and costs of natural gas processing, transport and distribution is of great importance. In this context, the evaluation of the kinetics of H2S removal is a valuable procedure for the treatment of natural gas and disposal of the byproducts generated by the process. This evaluation was made in an absorption column packed with Raschig ring, where natural gas with H2S passes through a stagnant solution, being the contaminant absorbed by it. The content of H2S in natural gas in column output was monitored by an H2S analyzer. The comparison between the obtained curves and the study of the involved reactions have not only allowed to determine the efficiency and mass transfer controlling step of the involved processes but also make possible to effect a more detailed kinetic study and evaluate the commercial potential of each reagent

Avaliação e modelagem da absorção de H2S do gás natural em coluna de leito estagnado

Natural gas, although basically composed by light hydrocarbons, also presents contaminant gases in its composition, such as CO2 (carbon dioxide) and H2S (hydrogen sulfide). The H2S, which commonly occurs in oil and gas exploration and production activities, causes damages in oil and natural gas pipelines. Consequently, the removal of hydrogen sulfide gas will result in an important reduction in operating costs. Also, it is essential to consider the better quality of the oil to be processed in the refinery, thus resulting in benefits in economic, environmental and social areas. All this facts demonstrate the need for the development and improvement in hydrogen sulfide scavengers. Currently, the oil industry uses several processes for hydrogen sulfide removal from natural gas. However, these processes produce amine derivatives which can cause damage in distillation towers, can cause clogging of pipelines by formation of insoluble precipitates, and also produce residues with great environmental impact. Therefore, it is of great importance the obtaining of a stable system, in inorganic or organic reaction media, able to remove hydrogen sulfide without formation of by-products that can affect the quality and cost of natural gas processing, transport, and distribution steps. Seeking the study, evaluation and modeling of mass transfer and kinetics of hydrogen removal, in this study it was used an absorption column packed with Raschig rings, where the natural gas, with H2S as contaminant, passed through an aqueous solution of inorganic compounds as stagnant liquid, being this contaminant gas absorbed by the liquid phase. This absorption column was coupled with a H2S detection system, with interface with a computer. The data and the model equations were solved by the least squares method, modified by Levemberg-Marquardt. In this study, in addition to the water, it were used the following solutions: sodium hydroxide, potassium permanganate, ferric chloride, copper sulfate, zinc chloride, potassium chromate, and manganese sulfate, all at low concentrations (»10 ppm). These solutions were used looking for the evaluation of the interference between absorption physical and chemical parameters, or even to get a better mass transfer coefficient, as in mixing reactors and absorption columns operating in counterflow. In this context, the evaluation of H2S removal arises as a valuable procedure for the treatment of natural gas and destination of process by-products. The study of the obtained absorption curves makes possible to determine the mass transfer predominant stage in the involved processes, the mass transfer volumetric coefficients, and the equilibrium concentrations. It was also performed a kinetic study. The obtained results showed that the H2S removal kinetics is greater for NaOH. Considering that the study was performed at low concentrations of chemical reagents, it was possible to check the effect of secondary reactions in the other chemicals, especially in the case of KMnO4, which shows that your by-product, MnO2, acts in H2S absorption process. In addition, CuSO4 and FeCl3 also demonstrated to have good efficiency in H2S removal

Cerâmicas avançadas no processo de retificação cilíndrica externa de mergulho utilizando a técnica da mínima quantidade de lubrificação (MQL) com rebolos diamantados

Nas últimas duas décadas, as cerâmicas avançadas têm sido exaustivamente utilizadas em aplicações na indústria devido às suas propriedades de elevada resistência ao desgaste e dureza. Entretanto, ainda se tem um alto custo agregado ao acabamento da peça. Esse acabamento geralmente é feito pelo processo de retificação, único processo economicamente viável que produz superfícies de elevada qualidade e precisão geométrica. Nesse contexto, as empresas vêm buscando a otimização no processo de retificação como, por exemplo, a redução do fluxo de fluido de corte utilizado, o que também visa atender exigências mundiais de preservação ambiental. Desta forma, este projeto pretendeu explorar a técnica da Mínima Quantidade de Lubrificação (MQL) na retificação cilíndrica externa de mergulho em cerâmicas com rebolos diamantados. Foram utilizados dois métodos de refrigeração: o convencional e o MQL, com três avanços de corte para cada caso. Foram usados um bocal convencional e um bocal para o MQL, tendo este um uniformizador de saída do jato. Foram analisadas como variáveis de saída: a emissão acústica, relação G, aspecto da superfície via microscopia eletrônica de varredura (MEV), rugosidade e circularidade. Assim, embora a refrigeração convencional ainda apresente os melhores resultados em comparação com a refrigeração com MQL, esta última pode atender os requisitos necessários para diversas aplicações, em especial quando utilizadas baixas espessuras equivalentes de corte (h eq). Além disso, a técnica de MQL possui a vantagem de gerar um menor impacto ambiental em comparação com a lubrificação convencional, devido ao uso mínimo de fluido de corte cujo descarte é cada vez mais regulamentado e custoso.

Degradação eletroquímica de benzeno, tolueno e xileno via oxidação eletroquímica utilizando eletrodo Ti/Pt

This work is directed to the treatment of organic compounds present in produced water from oil using electrochemical technology. The water produced is a residue of the petroleum industry are difficult to treat , since this corresponds to 98 % effluent from the effluent generated in the exploration of oil and contains various compounds such as volatile hydrocarbons (benzene, toluene, ethylbenzene and xylene), polycyclic aromatic hydrocarbons (PAHs), phenols, carboxylic acids and inorganic compounds. There are several types of treatment methodologies that residue being studied, among which are the biological processes, advanced oxidation processes (AOPs), such as electrochemical treatments electrooxidation, electrocoagulation, electrocoagulation and eletroredution. The electrochemical method is a method of little environmental impact because instead of chemical reagents uses electron through reactions of oxide-reducing transforms toxic substances into substances with less environmental impact. Thus, this paper aims to study the electrochemical behavior and elimination of the BTX (benzene, toluene and xylene) using electrode of Ti/Pt. For the experiment an electrochemical batch system consists of a continuous source, anode Ti/Pt was used, applying three densities of current (1 mA/cm2, 2,5 mA/cm2 and 5 mA/cm2). The synthetic wastewater was prepared by a solution of benzene, toluene and xylene with a concentration of 5 ppm, to evaluate the electrochemical behavior by cyclic voltammetry and polarization curves, even before assessing the removal of these compounds in solution by electrochemical oxidation. The behavior of each of the compounds was evaluated by the use of electrochemical techniques indicate that each of the compounds when evaluated by cyclic voltammetry showed partial oxidation behavior via adsorption to the surface of the Ti/Pt electrode. The adsorption of each of the present compounds depends on the solution concentration but there is the strong adsorption of xylene. However, the removal was confirmed by UV-Vis, and analysis of total organic carbon (TOC), which showed a percentage of partial oxidation (19,8 % - 99,1 % TOC removed), confirming the electrochemical behavior already observed in voltammetry and cyclic polarization curves

Síntese de catalisadores nanoporosos na ausência total e parcial de direcionadores orgânicos para pirólise catalítica de óleos pesados e intermediários

The processing of heavy oil produced in Brazil is an emergency action and a strategic plan to obtain self-sufficiency and economic surpluses. Seen in these terms, it is indispensable to invest in research to obtain new catalysts for obtaining light fraction of hydrocarbons from heavy fractions of petroleum. This dissertation for the degree of Doctor of Philosophy reports the materials preparation that combine the high catalytic activity of zeolites with the greater accessibility of the mesoporosity, more particularly the HZSM-5/MCM-41 hybrid, done by synthesis processes with less environmental impact than conventional ones. Innovative methodologies were developed for the synthesis of micro-mesoporous hybrid material by dual templating mechanism and from crystalline zeolitic aluminosilicate in the absence of organic template. The synthesis of hybrid with pore bimodal distribution took place from one-single organic directing agent aimed to eliminate the use of organic templates, acids of any kind or organic solvents like templating agent of crystalline zeolitic aluminosilicate together with temperature-programmed microwave-assisted, making the experimental procedures of preparation most practical and easy, with good reproducibility and low cost. The study about crystalline zeolitic aluminosilicate in the absence of organic template, especially MFI type, is based on use of H2O and Na+ cation playing a structural directing role in place of an organic template. Advanced characterization techniques such as X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), Highresolution Transmission Electron Microscopy (HRTEM), Adsorption of N2 and CO2, kinetic studies by Thermogravimetric Analysis (TGA) and Pyrolysis coupled to Gas Chromatography/Mass Spectrometry (Pyrolysis-GC/MS) were employed in order to evaluate the synthesized materials. Achieve the proposed objectives, has made available a set of new methodologies for the synthesis of zeolite and hybrid micro-mesoporous material, these suitable for catalytic pyrolysis of heavy oils aimed at producing light fraction

Hábito alimentar e percepção ambiental : um estudo de caso com estudantes do Ensino Médio em Natal-RN

This study has as objective to examine the level of perception of high school students from two private schools in Natal-RN about the existence of a direct link between alimentary habit and its effects on environmental. The research was lead with 433 students, who had their school alimentary habits investigated according to the 24-hour recall method and presents the results of data collection from their opinions on participating in the generation of industrialized solid residues and their yearnings about the improvements of the standard of the food offered in the school. The students show a high rate of grading age for level at school, traditional family structure, riding, predominantly, by car or by bus in the house-school-house way, have generally all three important meals at home, feed frequently at their school, getting it from their won school, which included, mainly, soft drinks and fried or grilled appetizers; show a good knowledge about selective collectors, however with a high variation in their correct use. They show significant approval in the existence of a connection between their alimentary habits and debased effects about environmental and consider their food compounds at school could improve the offering of health/natural food, slowing industrialized foods, which are highly used, sometimes. The study on the students knowledge and concern level with regard to the interface alimentary habit-environmental impact allowed delimitating some of the mainly involved components in the alimentary choices of the same students in the school environment, what might help to develop a set of proposals that stimulates the formation of a responsible consumption standard among teenagers and the need of a consideration about the consequences of their choices

Análise da vulnerabilidade ambiental no estuário do Rio Curimataú/Cunhaú, Baía Formosa e Canguaretama - RN

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Fragilidade ambiental da bacia hidrográfica do Rio Punaú (RN) e área litorânea adjacente

Hydrographic basins always exercised a big fascination over humankind that attracted for its scenery beauty or for its richness in natural resources, had been acting in order to modify these important ecosystems without, therefore, considering the possible consequences of these changes. The attributed importance to the coast ecosystems, in eminence to the hydrographic basin of Punaú river and adjacent areas, is had when it s verified the diversity of the ecosystems that contemplate it. Hydrographic basin in evidence in Rio Grande do Norte state, occupies an area of nearly 652.71 km², being it sited in the homogeneous micro-region Litoral Nordeste, with a regional population estimated in nearly 75,188 inhabitants, according to the Anuário Estatístico do Rio Grande do Norte 2004. The region of the researched basin is formed by seven municipal districts related as it follows: Maxaranguape, Pedra Grande, Pureza, Rio do Fogo, São Miguel de Touros, Taipu and Touros, but Maxaranguape, Rio do Fogo, Touros and Pureza have a direct participation in the basin. Basin in study have it lands evaluated according to the agriculturist aptitude by the conventionally methodology practiced in the country, having as objective, then, a compara-tive analysis between the ambient unities, Aeolian littoral and coast tray, identified in the researched area. From the characterization of the physic way of the area in study and owning the kept data, it was proceeded the integrated analysis of the structural elements of the landscape which were evidenced that the fragile areas are associated with the areas of agriculture cultivation, such as the ones of irregular occupation. About the degradation, the ambient diagnostic of the basin indicated that the equivalent to the Aeolian Littoral Ambient Unit correspond to the bigger pledging of the ambient quality, in other words, high ambient fragility, being this result due to the use and occupation of the soil, propitiating this way, vulnerability in the vegetal cover of the area, despite it disposes of a low agriculture cultivation percentage. Already in the Coast Ambient Tray, is emphasized the medium ambient fragility, despite of the high index of cultivated area. In a general way, the total area of the hydrographic basin of Punaú river and adjacent areas presented ambient impacts over the tolerance limit, indicating the necessity of a review of the practices of use and handling of the soil, reforesting of the water courses edges, control of erosion and contamination of the aqueous in the perspective to reduce the effects of the impacts due to the use and occupation of the basin in regard. The present search evaluated the ambient impacts diagnosised in the hydrographic basin of Punaú river and adjacent areas, pointing the causes and the probable consequences of the damages caused by these impacts to the basin ambient. From the analysis of these data, if was possible to become explicit how they are fundamental as key elements in the process of decision taking in the ambient questions

O licenciamento ambiental da mineração no Quadrilátero Ferrífero de Minas Gerais: uma análise da implementação de medidas de controle ambiental formuladas em EIAs/RIMAs

Instrumento de política pública ligado ao licenciamento ambiental prévio de projetos de empreendimentos potencialmente degradadores do ambiente, a Avaliação de Impacto Ambiental (AIA), atualmente, apresenta algumas inconsistências. Dentre elas, autores registram a disparidade no que se refere à indicação e à efetiva implantação das medidas de controle ambiental estabelecidas nos EIA/RIMAs. Diante disso, o presente trabalho analisa a implantação das medidas mitigadoras estabelecidas para empreendimentos minerais licenciados pela Fundação Estadual do Meio Ambiente (FEAM) do Estado de Minas Gerais, para a região do Quadrilátero Ferrífero. No estudo, constata-se que intervenções ambientais são hoje partes integrantes dos projetos minerais; porém, como na mineração a operação impõe certo dinamismo ao empreendimento, verifica-se que parte das medidas mitigadoras apontadas no EIA acaba não sendo executada, como o previsto e o aprovado na fase da Licença Prévia (LP), enquanto outras apenas ficam listadas como propostas de mitigação de impactos, deixando de ser efetivamente executadas.

La dimensión ambiental en el desarrollo de América Latina

Incluye Bibliografía

Avaliação preliminar do potencial turístico do município de rifaina (SP) e os impactos decorrentes do uso público de seus atrativos paisagísticos

This paper attempts to assess both the touristic potential of scenic attractions and the environmental impacts resulting from the public use of such attractions in the Rifaina Municipality, State of São Paulo, Southeastern Brazil. In the recent past, this municipality had its economy concentrated in rural activities (livestock, corn, rice and bean crops) and in the ceramic industry (production of bricks, tiles and shackles),which was largely developed in the floodplain of the Rio Grande before the construction of the Jaguara Power Plant Dam. The impacts resulting from touristic activities were evaluated by applying the VIM - Visitor Impact Management method, with emphasis on biophysical indicators. The main touristic attractions analyzed were: (1) Rifaina artificial beach; (2) Jaguara Reservoir; (3) Morro do Chapéu (scenic hill); (4) Touristic railroad; and (5) Cuestas cliffs. Attractions (1) and (2) are the most exploited ones, including, in the second case, nautical sports, sportive and craft fishing, and summer lodging. Although currently disabled, the touristic railroad presents potential conditions to be re-explored. Attractions (3) and (5), despite keeping high landscape and ecological ecotouristic potential, are the least visited places. In the present paper, a preliminary characterization of the major issues of tourism industry in the Rifaina municipality is made, including suggestions for the sustainable exploitation of tourism resources. The final results of the environmental impact evaluation of the tourism activities include small impacts in attractions (4) and (5) and moderate impacts to the three first attractions. In order to keep the sustainable touristic potential for that municipality this study proposes the improvement of the following measures: to foster research projects on technical or scientific aspects of the touristic attractions, improvement of tourism infrastructure and the creation of an Environmental Protection Area (APA) of the cuestas' scarps.

Interacciones intergubernamentales entre los impuestos sobre el petróleo y el gas y la protección ambiental

Incluye bibliografia

Políticas para mejorar la gestión ambiental en las PYMES argentinas y promover su oferta de bienes y servicios ambientales

Incluye Bibliografía