Mass transfer coefficient for drying of moist particulate in a bubbling fluidized bed

Experiments on drying of moist particles by ambient air were carried out to measure the mass transfer coefficient in a bubbling fluidized bed. Fine glass beads of mean diameter 125?µm were used as the bed material. Throughout the drying process, the dynamic material distribution was recorded by electrical capacitance tomography (ECT) and the exit air condition was recorded by a temperature/humidity probe. The ECT data were used to obtain qualitative and quantitative information on the bubble characteristics. The exit air moisture content was used to determine the water content in the bed. The measured overall mass transfer coefficient was in the range of 0.0145–0.021?m/s. A simple model based on the available correlations for bubble-cloud and cloud-dense interchange (two-region model) was used to predict the overall mass transfer coefficient. Comparison between the measured and predicted mass transfer coefficient have shown reasonable agreement. The results were also used to determine the relative importance of the two transfer regions.

Assembly of a high-dielectric constant thin TiOX layer directly on H-terminated semiconductor diamond

A high-dielectric constant (high-k) TiOx thin layer was fabricated on hydrogen-terminated diamond (H-diamond) surface by low temperature oxidation of a thin titanium layer in ambient air. The metallic titanium layer was deposited by sputter deposition. The dielectric constant of the resultant TiOx was calculated to be around 12. The capacitance density of the metal-oxide-semiconductor (MOS) based on the TiOx/H-diamond was as high as 0.75 µF/cm2 contributed from the high-k value and the very thin thickness of the TiOx layer. The leakage current was lower than 10-13 A at reverse biases and 10-7A at the forward bias of -2 V. The MOS field-effect transistor based on the high-k TiOx/H-diamond was demonstrated. The utilization of the high-k TiOx with a very thin thickness brought forward the features of an ideally low subthreshold swing slope of 65 mV per decade and improved drain current at low gate voltages. The advantages of the utilization high-k dielectric for diamond MOSFETs are anticipated.

Autonomic and embedded wireless sensor protocols for critical infrastructures

The tragic events of September 11th ushered a new era of unprecedented challenges. Our nation has to be protected from the alarming threats of adversaries. These threats exploit the nation's critical infrastructures affecting all sectors of the economy. There is the need for pervasive monitoring and decentralized control of the nation's critical infrastructures. The communications needs of monitoring and control of critical infrastructures was traditionally catered for by wired communication systems. These technologies ensured high reliability and bandwidth but are however very expensive, inflexible and do not support mobility and pervasive monitoring. The communication protocols are Ethernet-based that used contention access protocols which results in high unsuccessful transmission and delay. An emerging class of wireless networks, named embedded wireless sensor and actuator networks has potential benefits for real-time monitoring and control of critical infrastructures. The use of embedded wireless networks for monitoring and control of critical infrastructures requires secure, reliable and timely exchange of information among controllers, distributed sensors and actuators. The exchange of information is over shared wireless media. However, wireless media is highly unpredictable due to path loss, shadow fading and ambient noise. Monitoring and control applications have stringent requirements on reliability, delay and security. The primary issue addressed in this dissertation is the impact of wireless media in harsh industrial environment on the reliable and timely delivery of critical data. In the first part of the dissertation, a combined networking and information theoretic approach was adopted to determine the transmit power required to maintain a minimum wireless channel capacity for reliable data transmission. The second part described a channel-aware scheduling scheme that ensured efficient utilization of the wireless link and guaranteed delay. Various analytical evaluations and simulations are used to evaluate and validate the feasibility of the methodologies and demonstrate that the protocols achieved reliable and real-time data delivery in wireless industrial networks.

Investigation into possible causes of elevated ozone concentrations in Miami, Florida

Ozone readings which exceeded the National Ambient Air Quality Standard of 120 ppbv were recorded in Miami, Florida during 1978 and 1980. Similar elevated concentrations of ozone extended across upper Florida and into the Southeastern portion of the United States. It is concluded that tropospheric transport of ozone into the Miami area occurs. This conclusion is supported by lead analyses of atmospheric samples taken in Miami and by isentropic trajectories. Six case studies are presented. In all cases transport of ozone into Florida appears to occur. In only four of the cases does this result in elevated ozone levels in Miami. In one case lower Florida was experiencing an oceanic influx of air and low ozone concentrations. In the other case Miami was experiencing a stagnation and high ozone concentrations apparently generated locally. The long range transport of ozone across the Southeastern United States appears to result from circulation within a weather pattern characterized by a stagnant high pressure system over the Southeastern United States.

Determinação da concentração de metais no material particulado (PM10 e PM2,5) do ar atmosférico em uma área urbana da cidade do Natal – RN

This study aimed to assess ambient air quality in a urban area of Natal, capital of Rio Grande do Norte (latitude 5º49'29 '' S and longitude 35º13'34'' W), aiming to determine the metals concentration in particulate matter (PM10 and PM2,5) of atmospheric air in the urban area o the Natal city. The sampling period for the study consisted of data acquisition from January to December 2012. Samples were collected on glass fiber filters by means of two large volumes samplers, one for PM2,5 (AGV PM 2,5) and another for PM10 (PM10 AGV). Monthly averages ranged from 8.92 to 19.80 g.m-3 , where the annual average was 16,21 g.m-3 for PM10 and PM2,5 monthly averages ranged from 2,84 to 7,89 g.m -3 , with an annual average of 5,61 g.m-3 . The results of PM2,5 and PM10 concentrations were related meteorological variables and for information on the effects of these variables on the concentration of PM, an exploratory analysis of the data using Principal Component Analysis (PCA) was performed. The results of the PCA showed that with increasing barometric pressure, the direction of the winds, the rainfall and relative humidity decreases the concentration of PM and the variable weekday little influence compared the meteorological variables. Filters containing particulate matter were selected in six days and subjected to microwave digestion. After digestion samples were analyzed by with Inductively Coupled Plasma Mass Spectrometry (ICP-MS). The concentrations for heavy metals Vanadium, Chromium, Manganese, Nickel, Copper, Arsenic and lead were determined. The highest concentrations of metals were for Pb and Cu, whose average PM10 values were, respectively, 5,34 and 2,34 ng.m-3 and PM2,5 4,68 and 2,95 ng.m-3 . Concentrations for metals V, Cr, Mn, Ni, and Cd were respectively 0,13, 0,39, 0,48, 0,45 and 0,03 ng.m-3 for PM10 fraction and PM2,5 fraction, 0,05, 0,10, 0,10, 0,34 and 0,01 ng.m-3. The concentration for As was null for the two fractions

Caracterização do material particulado e avaliação do risco ocupacional e mecanismos moleculares associados à queima artesanal da castanha de caju

Brazil is among the largest cashew nut producers of the world. However, the roasting process is still carried out artisanally, especially in the Brazilian semiarid region. In face of this occupational problem, the aim of this study was to perform a physical-chemical characterization of the particulate matter (PM) emitted by the roasting of cashew nuts, as well as to determine the occupational risk and molecular mechanisms associated. The most evident PM characteristics were the prevalence of fine particles, typical biomass burning morphologies such as tar ball and the presence of the elements K, Cl, S, Ca and Fe. In addition, atmospheric modeling analyses suggest that these particles can reach neighboring regions of the emission source. Polycyclic aromatic hydrocarbons (PAHs) with carcinogenic potential, such as benzo[a]pyrene, dibenz[a,h]anthracene, benzo[a]anthracene, benzo[b]fluoranthene, chrysene, benzo[k]fluoranthene, indeno[1,2,3-c,d]pyrene and benzo[j]fluoranthene were the most abundant PAHs found in the two air monitoring campaigns. Among the identified oxy-PAH the benzanthrone (7H-benz[d,e]anthracen-7-one) had the highest concentration and the evaluation of lifetime cancer risk showed an increase of 12 to 37 cases of cancer for every 10,000 exposed people. Chemical analysis of roasted cashew nuts identified the PAHs: phenanthrene, benzo[g,h,i]perylene, pyrene and benzo[a]pyrene, besides the 3-pentadecilfenol allergen (urushiol analogue) as prevalent. Occupational exposure to PAHs was confirmed by the increase of urinary 1-hydroxypyrene levels and genotoxic effects were evidenced by the increase on micronuclei and nuclear bud frequency in exfoliated buccal mucosa cells among the exposed workers. Other biomarkers of effects such as karyorrhexis, pyknotic, karyolytic, condensed chromatin and binucleated cells also have their frequencies increased when compared to an unexposed control group. The investigation of the molecular mechanisms associated with the PM organic extract showed cytotoxicity in human lung cell lines (A549) at concentrations ≥ 4 nM BaPeq. Using non-cytotoxic doses the extract was able to activate proteins involved in the DNA damage response pathway (Chk1 and p53). Moreover, the specific contribution of the four most representative PAHs in the cashew nut roasting sample showed that benzo[a]pyrene was the most efficient to activate Chk1 and p53. Finally, the organic extract was able to increase persistently the mRNA expression involved in the PAHs metabolism (CYP1A1 and CYP1B1), inflammatory response (IL-8 and TNF-α) and cell cycle arrest (CDKN1A) for DNA repair (DDB2). The high PM concentrations and its biological effects associated warn of the serious harmful effects of artisanal cashew nut roasting and urgent actions should be taken to the sustainable development of this activity.

Caracterização do material particulado e avaliação do risco ocupacional e mecanismos moleculares associados à queima artesanal da castanha de caju

Brazil is among the largest cashew nut producers of the world. However, the roasting process is still carried out artisanally, especially in the Brazilian semiarid region. In face of this occupational problem, the aim of this study was to perform a physical-chemical characterization of the particulate matter (PM) emitted by the roasting of cashew nuts, as well as to determine the occupational risk and molecular mechanisms associated. The most evident PM characteristics were the prevalence of fine particles, typical biomass burning morphologies such as tar ball and the presence of the elements K, Cl, S, Ca and Fe. In addition, atmospheric modeling analyses suggest that these particles can reach neighboring regions of the emission source. Polycyclic aromatic hydrocarbons (PAHs) with carcinogenic potential, such as benzo[a]pyrene, dibenz[a,h]anthracene, benzo[a]anthracene, benzo[b]fluoranthene, chrysene, benzo[k]fluoranthene, indeno[1,2,3-c,d]pyrene and benzo[j]fluoranthene were the most abundant PAHs found in the two air monitoring campaigns. Among the identified oxy-PAH the benzanthrone (7H-benz[d,e]anthracen-7-one) had the highest concentration and the evaluation of lifetime cancer risk showed an increase of 12 to 37 cases of cancer for every 10,000 exposed people. Chemical analysis of roasted cashew nuts identified the PAHs: phenanthrene, benzo[g,h,i]perylene, pyrene and benzo[a]pyrene, besides the 3-pentadecilfenol allergen (urushiol analogue) as prevalent. Occupational exposure to PAHs was confirmed by the increase of urinary 1-hydroxypyrene levels and genotoxic effects were evidenced by the increase on micronuclei and nuclear bud frequency in exfoliated buccal mucosa cells among the exposed workers. Other biomarkers of effects such as karyorrhexis, pyknotic, karyolytic, condensed chromatin and binucleated cells also have their frequencies increased when compared to an unexposed control group. The investigation of the molecular mechanisms associated with the PM organic extract showed cytotoxicity in human lung cell lines (A549) at concentrations ≥ 4 nM BaPeq. Using non-cytotoxic doses the extract was able to activate proteins involved in the DNA damage response pathway (Chk1 and p53). Moreover, the specific contribution of the four most representative PAHs in the cashew nut roasting sample showed that benzo[a]pyrene was the most efficient to activate Chk1 and p53. Finally, the organic extract was able to increase persistently the mRNA expression involved in the PAHs metabolism (CYP1A1 and CYP1B1), inflammatory response (IL-8 and TNF-α) and cell cycle arrest (CDKN1A) for DNA repair (DDB2). The high PM concentrations and its biological effects associated warn of the serious harmful effects of artisanal cashew nut roasting and urgent actions should be taken to the sustainable development of this activity.

Thermal measurements on sub-Antarctic megaherbs and environmental characteristics on Campbell Island in 2010

We evaluated whether heating occurs in sub-Antarctic megaherbs, and the relation of heating to relevant environmental variables. We measured leaf and inflorescence temperature in six sub-Antarctic megaherb species on Campbell Island, latitude 52.3°S, New Zealand Biological Region. Using thermal imaging camera (Fluke TI20, http://www.fluke.com/fluke/caen/support/software/ti-update) and thermal probe (Fluke 51 II digital thermal probe), in combination with measurement of solar radiation, ambient air temperature, wind speed, wind chill and humidity.

Anodic oxidation of InP in KOH electrolytes

The anodic behavior of InP in 1 mol dm-3 KOH was investigated and compared with its behavior at higher concentrations of KOH. At concentrations of 2 mol dm-3 KOH or greater, selective etching of InP occurs leading to thick porous InP layers near the surface of the sustrate. In contrast, in 1 mol dm-3 KOH, no such porous layers are formed but a thin surface film is formed at potentials in the range 0.6 V to 1.3 V. The thickness of this film was determined by spectroscopic ellipsometry as a function of the upper potential and the measured film thickness corresponds to the charge passed up to a potential of 1.0 V. Anodization to potentials above 1.5 V in 1 mol dm- 3 KOH results in the growth of thick, porous oxide films (~ 1.2 µm). These films are observed to crack, ex-situ, due to shrinkage after drying in ambient air. Comparisons between the charge density and film thickness measurements indicate a porosity of approximately 77% for such films.

(Table 1) Annual mean concentrations of atmospheric a- and g-Hexachlorocyclohexane at stations Alert, Canada and Zeppelin, Norway

Twelve year datasets of weekly atmospheric concentrations of alpha- and gamma-HCH were compared between the two Arctic monitoring stations of Alert, Nunavut, Canada, and Zeppelin Mountain, Svalbard, Norway. Time-series analysis was conducted with the use of dynamic harmonic regression (DHR), which provided a very good model fit, to examine both the seasonal behaviour in these isomers and the longer-term, underlying trends. Strong spatial differences were not apparent between the two sites, although subtle differences in seasonal behaviour and composition were identified. For example, the composition of gamma-HCH to total HCH (alpha + gamma) was greater at Zeppelin compared to Alert, probably reflecting this site's proximity to major use regions of lindane. Pronounced seasonality in air concentrations for gamma-HCH was marked by a 'spring maximum event' (SME), confirming earlier studies. For alpha-HCH, the SME was much weaker and only evident at Alert, whereas at Zeppelin, seasonal fluctuations for alpha-HCH were marked by elevated concentrations in summer and lower concentrations during winter, with this pattern most apparent for the years after 2000. We attribute this difference in spatial and temporal patterns to the Arctic oscillation. A similar climatic pattern was not evident at either site in the gamma-HCH data. Seasonally adjusted, long-term trends revealed declining concentrations at both sites for alpha- and gamma-HCH over the entire time-series. Recent legislation affecting lindane use appear to account for this decline in gamma-HCH, with little evidence of a delay or 'lag' between the banning of lindane in Europe (a main source region) or Canada, and a decline in air concentrations observed at both Arctic sites.

Multifunctional anthraquinone-based sensors: UV, O2and time

An anthraquinone dye, Remazol brilliant blue R, RBBR, is used to create an indicator which can function as: (i) a UV dosimeter, (ii) an O2 indicator and (iii) a ‘Consume within’ indicator, CWI, for fresh, refrigerated foods. The dye is encapsulated in an ink containing a polymer, glycerol and a UV-activated semiconductor photocatalyst, titanium dioxide. When cast as a film, the dye is readily reduced by the TiO2 photocatalyst nanoparticles, thereby changing the colour of the film from blue to yellow, via a transitional green colour. The RBBR indicator is appropriately formulated, and covered with a film of Sellotape, which acts as an O2 barrier, so as to act as a sunburn warning indicator for people with skin type II. In the absence of the layer of Sellotape the RBBR indicator is used as an, albeit slow, sensor for measuring ambient levels of O2. Finally, by keeping the Sellotape layer, a UV-activated, yellow-coloured, RBBR indicator film is found to take ca. 42 h at 5 °C in ambient air to attain a green colour, and, on this basis, it is demonstrated as a possible CWI for refrigerated fresh foods.

Evaluation of strontium-site-deficient Sr2Fe1.4Co0.1Mo0.5O6-δ-based perovskite oxides as intermediate temperature solid oxide fuel cell cathodes

In this paper strontium-site-deficient Sr₂Fe_1.4Co_0.1Mo_0.5O_6-δ-based perovskite oxides (S_xFCM) were prepared and evaluated as the cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFCs). All samples exhibited a cubic phase structure and the lattice shrinked with increasing the Sr-deficiency as shown in XRD patterns. XPS results determined that the transition elements (Co/Fe/Mo) in S_xFCM oxides were in a mixed valence state, demonstrating the small polaron hopping conductivity mechanism existed. Among the samples, S_1.950FCM presented the lowest coefficient of thermal expansion of 15.62 × 10^-6 K^-1, the highest conductivity value of 28 S cm^-1 at 500 °C, and the lowest interfacial polarization resistance of 0.093 Ω cm² at 800 °C, respectively. Furthermore, an anode-supported single cell with a S_1.950FCM cathode was prepared, demonstrating a maximum power density of 1.16 W cm^-2 at 800 °C by using wet H₂ (3% H₂O) as the fuel and ambient air as the oxidant. These results indicate that the introduction of Sr-deficiency can dramatically improve the electrochemical performance of Sr₂Fe_1.4Co_0.1Mo_0.5O_6-δ, showing great promise as a novel cathode candidate material for IT-SOFCs.

High performance cobalt-free Cu1.4Mn1.6O4 spinel oxide as an intermediate temperature solid oxide fuel cell cathode

In this work Cu_1.4Mn_1.6O₄ (CMO) spinel oxide is prepared and evaluated as a novel cobalt-free cathode for intermediate temperature solid oxide fuel cells (IT-SOFCs). Single phase CMO powder with cubic structure is identified using XRD. XPS results confirm that mixed Cu⁺/Cu²⁺ and Mn³⁺/Mn⁴⁺ couples exist in the CMO sample, and a maximum conductivity of 78 S cm⁻¹ is achieved at 800 °C. Meanwhile, CMO oxide shows good thermal and chemical compatibility with a 10 mol% Sc₂O₃ stabilized ZrO₂ (ScSZ) electrolyte material. Impedance spectroscopy measurements reveals that CMO exhibits a low polarization resistance of 0.143 Ω cm² at 800 °C. Furthermore, a Ni-ScSZ/ScSZ/CMO single cell demonstrates a maximum power density of 1076 mW cm⁻² at 800 °C under H₂ (3% H₂O) as the fuel and ambient air as the oxidant. These results indicate that Cu_1.4Mn_1.6O₄ is a superior and promising cathode material for IT-SOFCs.

Modeling of Turbulent Natural Gas and Biogas Flames of the Delft Jet-in-Hot-Coflow Burner: Effects of Coflow Temperature, Fuel Temperature and Fuel Composition on the Flame Lift-Off Height

The structure of a turbulent non-premixed flame of a biogas fuel in a hot and diluted coflow mimicking moderate and intense low dilution (MILD) combustion is studied numerically. Biogas fuel is obtained by dilution of Dutch natural gas (DNG) with CO2. The results of biogas combustion are compared with those of DNG combustion in the Delft Jet-in-Hot-Coflow (DJHC) burner. New experimental measurements of lift-off height and of velocity and temperature statistics have been made to provide a database for evaluating the capability of numerical methods in predicting the flame structure. Compared to the lift-off height of the DNG flame, addition of 30 % carbon dioxide to the fuel increases the lift-off height by less than 15 %. Numerical simulations are conducted by solving the RANS equations using Reynolds stress model (RSM) as turbulence model in combination with EDC (Eddy Dissipation Concept) and transported probability density function (PDF) as turbulence-chemistry interaction models. The DRM19 reduced mechanism is used as chemical kinetics with the EDC model. A tabulated chemistry model based on the Flamelet Generated Manifold (FGM) is adopted in the PDF method. The table describes a non-adiabatic three stream mixing problem between fuel, coflow and ambient air based on igniting counterflow diffusion flamelets. The results show that the EDC/DRM19 and PDF/FGM models predict the experimentally observed decreasing trend of lift-off height with increase of the coflow temperature. Although more detailed chemistry is used with EDC, the temperature fluctuations at the coflow inlet (approximately 100K) cannot be included resulting in a significant overprediction of the flame temperature. Only the PDF modeling results with temperature fluctuations predict the correct mean temperature profiles of the biogas case and compare well with the experimental temperature distributions.

Morphology and material stability in polymer solar cells

Polymer solar cells are promising in that they are inexpensive to produce, and due to their mechanical flexibility have the potential for use in applications not possible for more traditional types of solar cells. The performance of polymer solar cells depends strongly on the distribution of electron donor and acceptor material in the active layer. Understanding the connection between morphology and performance as well as how to control the morphology, is therefore of great importance. Furthermore, improving the lifetime of polymer solar cells has become at least as important as improving the efficiency.   In this thesis, the relation between morphology and solar cell performance is studied, and the material stability for blend films of the thiophene-quinoxaline copolymer TQ1 and the fullerene derivatives PCBM and PC70BM. Atomic force microscopy (AFM) and scanning transmission X-ray microscopy (STXM) are used to investigate the lateral morphology, secondary ion mass spectrometry (SIMS) to measure the vertical morphology and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy to determine the surface composition. Lateral phase-separated domains are observed whose size is correlated to the solar cell performance, while the observed TQ1 surface enrichment does not affect the performance. Changes to the unoccupied molecular orbitals as a result of illumination in ambient air are observed by NEXAFS spectroscopy for PCBM, but not for TQ1. The NEXAFS spectrum of PCBM in a blend with TQ1 changes more than that of pristine PCBM. Solar cells in which the active layer has been illuminated in air prior to the deposition of the top electrode exhibit greatly reduced electrical performance. The valence band and absorption spectrum of TQ1 is affected by illumination in air, but the effects are not large enough to account for losses in solar cell performance, which are mainly attributed to PCBM degradation at the active layer surface.