Separation of yttrium from heavy lanthanide by CA-100 using the complexing agent

The selective extraction of yttrium front heavy lanthanide by liquid-liquid extraction using CA-100 in the presence of the complexing agent, such as EDTA, DTPA, and HEDTA was investigated. The extraction of heavy lanthanide in the present of the complexing agent was Suppressed when compared to that of Y because of the masking effect, but the selective extraction of Y was enhanced. All complexing agents formed 1: 1 complex with rare earth elements (RE), and only free rare earth ions could take part in the extraction. The condition for separation was obtained by exploring the effects of the complexing agent concentration, the extractant concentration, pH and the equilibration time on the extraction of the heavy rare earth elements.

Selective separation of yttrium by CA-100 in the presence of a complexing agent

The selective separation of Y from yttrium solution containing small heavy rare earth (HRE) impurities (Ho, Er, Tm, Yb, Lu) by liquid-liquid extraction using CA-100 in the presence of a water-soluble complexing agent of ethylenediaminetetraacetic acid (EDTA) was experimentally studied at 298K. Experiments were carried Out in two feeds, Feed-I: [RE](f) = 4.94 x 10(-3) M, Y = 98.5%, HRE (Ho, Er, Tm, Yb, Lu) = 1.5%; Feed-II: [RE](f) = 4.94 x 10(-3) M, Y = 99.9%, HRE (Ho, Er, Tm, Yb, Lu) = 0.1%, as a function of equilibrium pH (pH(eq)), the concentration ratio of [EDTA]:[HRE impurities]. It was shown that the extraction of HRE in the presence of EDTA was suppressed when compared to that of Y because of the masking effect, while the selective extraction of Y was enhanced and the separation factors increased to maximum at appropriate condition for Feed-I: Y/Ho = 1.53, Y/Er = 3.09, Y/Tm = 5.61, Y/Yb = 12.04, Y/Lu = 27.51 at pH 4.37 and [EDTA]:[HRE impurities] = 4: 1, for Feed-II: Y/Ho = 1.32, Y/Er = 1.91, Y/Tm = 2.00, Y/Yb = 3.05, Y/Lu = 3.33 at pH 4.42 and [EDTA]: [HRE impurities] = 8:1. The separation and purification of Y by this method was discussed.

NaCl/Ca/Al as an efficient cathode in organic light-emitting devices

An efficient cathode NaCl/Ca/Al used to improve the performance of organic light-emitting devices (OLEDs) was reported. Standard NM-bis(1-naphthyl)-NAP-diphenyl-1,1' biphenyl 4,4'-dimaine (NPB)/tris-(8-hydroxyquinoline) aluminum (Alq(3)) devices with NaCl/Ca/Al cathode showed dramatically enhanced electroluminescent (EL) efficiency. A power efficiency of 4.6 lm/W was obtained for OLEDs with 2 nm of NaCl and 10 nm of Ca, which is much higher than 2.0 lm/W, 3.1 lm/W, 2.1 lm/ W and 3.6 lm/W in devices using, respectively, the LiF (1 nm)/Al, LiF (1 nm)/Ca (10 nm)/Al, Ca (10 nm)/Al and NaCl (2 nm)/ Al cathodes. The investigation of the electron injection in electron-only devices indicates that the utilization of the NaCl/Ca/Al cathode substantially enhances the electron injection current, which in case of OLEDs leads to the improvement of the brightness and efficiency.

Computer simulation for effect of Pr(III) on Ca(II) speciation in human interstitial fluid

A multiphase model of metal ion speciation in human interstitial fluid was constructed and the effect of Pr(III) on Ca(II) speciation was studied. Results show that free Ca2+, [Ca(HCO3)], and [Ca(Lac)] are the main species of Ca(II). Because of the competition of Pr(III) for ligands with Ca(II), the percentages of free Ca2+, [Ca(Lac)], and [Ca(His)(Thr)H-3] increase gradually and the percentages of CaHPO4(aq) and [Ca(Cit)(His)H-2] decrease gradually with the increase in the total concentration of Pr(III). However, the percentages of [Ca(HCO3)] and CaCO3(aq) first increase and then begin to decrease when the total concentration of Pr(III) exceeds 6.070 x 10(-4) M.

Synergistic extraction of zinc(II) with mixtures of CA-100 and cyanex 272

The extraction of zinc(II) from an aqueous chloride medium has been studied using mixtures of sec-nonylphenoxy acetic acid (CA-100) and bis(2,4,4-trimethylpentyl) phosphinic acid (Cyanex 272). The results demonstrate that zinc ion is extracted into heptane as ZnA(2).2HA with CA-100, ZnL2.2HL with Cyanex 272, and ZnA(2)L(2)H(2) with synergistic mixture. The equilibrium constants of the these species have been calculated and extraction mechanisms have been proposed. Thermodynamic parameters of the extraction process were determined by the temperature coefficient of extractability. The synergistic system enhances the extraction efficiency of zinc(II) and also improves the selectivity between zinc(II) and cadmium(II).

Kinetics and mechanism of Y(III) extraction with CA-100 using a constant interfacial cell with laminar flow

The Yttrium(III) extraction kinetics and mechanism with secnonylphonoxy acetic acid (CA-100) were investigated by a constant interfacial cell with laminar flow. The studies of interfacial tension and solubility of extractant and effects of the stirring rate, temperature, specific interfacial area and species concentration on the extraction rate showed that the extraction regime was dependent on the extraction conditions and the most probable reaction zone was at the liquid-liquid interface. The rate equation of extracting yttrium by CA-100 in heptane was Rf = k[Y3+]((a))[H(2)A(2)]((o))(0.88)[H+]((a))(-1.08).

Sol-gel deposition and luminescent properties of oxyapatite Ca-2(Y,Gd)(8)(SiO4)(6)O-2 phosphor films doped with rare earth and lead ions

Rare-earth and lead ions (Eu3+, Tb3+, Dy3+, Pb2+) doped Ca2Y8 (SiO4)(6)O-2 and Ca2Gd8(SiO4)(6)O-2 thin films have been dip- coated on silicon and quartz glass substrates through the sol- gel route. X- Ray diffraction (XRD), TG- DTA, scanning electron microscopy (SEM), atomic force microscopy (AFM), FT- IR and luminescence excitation and emission spectra as well as luminescence decays were used to characterize the resulting films. The results of XRD reveal that these films remain amorphous below 700 degreesC, begin to crystallize at 800 degreesC and crystallize completely around 1000 degreesC with an oxyapatite structure. The grain structure of the film can be seen clearly from SEM and AFM micrographs, where particles with various shapes and average size of 250 nm can be resolved. Eu3+ and Tb3+ show their characteristic red (D-5(0)-F-7(2)) and green (D-5(4) - F-7(5)) emission in the films with a quenching concentration of 10 and 6 mol% (of Y3+), respectively. The lifetime and emission intensity of Eu3+ increase with the temperature treatment from 700 to 1100 degreesC, while those of Tb3+ show a maximum at 800 degreesC. Energy transfer phenomena have been observed by activating the oxyapatite film host- lattice Ca2Gd8(SiO4)(6)O-2 with Tb3+ (Dy3+). In addition, Pb2+ can sensitize the Gd3+ sublattice in Ca2Gd8(SiO4)(6)O-2.

M_2CeO_4(M=Ca,Sr,Ba)的结构与发光特性

Sr_2CeO_4是一种新型的一维结构发光材料,其特殊的结构对其发光特性有决定性的作用。Sr2CeO4体系中可以顺利地进行能量传递,产生较强电荷迁移发光。合成了M2CeO4（M=Ca,Sr,Ba）,发现与Sr2CeO4具有类似结构的Ba2CeO4也可以发光,而结构完全发生了变化的Ca2CeO4则不发光。

Preparation, structure and luminescence of BaMAl10O17 : Eu2+ (M = Be, Mg, Ca, Zn, Cd, Mn, Co, Li) system

The BaMA(10)O(17) (M = Be, Mg, Ca, Zn, Cd, Mn, Co, Li) system has been synthesized by solid state method and characterized by XRD. The results show that when M is Mg, Zn, Mn, Co, Li, there exists the structure of beta-Al2O3 for BaMAl10O17 system, and when M indicates Cd, beta-Al2O3 structure is formed accompanying alpha-Al2O3 phase, and when M represents Be and Ca, beta-Al2O3 structure cannot be formed. This demonstrates that the condition forming beta-Al2O3 structure compounds for the system BaMAl10O17 is 0.05nm < R-M < 0.09nm (R-M represents the radius of M). The thought that if a M ion can form a stable spinel structure there exsits a corresponding magnetoplumbite and beta-alumina structure is proposed for BaMAl10O17 system according to the experimental results. When M is Li, Be, Zn, Eu2+ activator produces an emission of nearly 450 nm with half height width about 50 nm, when M is Mn, there are simultaneously the emissions of Eu2+ and Mn2+ and the excitation energy of Eu2+ can transfer to Mn2+ in the host, when M is Cd, Eu2+ displays a double-emission band, which can be explained by the Jahn-Teller's effect. It is possible for the system BaMAl10O17 with M being Li, Be, Zn to become blue-emitting component in three colour lamp through further study.

BaMAl_(10)O_(17)(M=Be,Mg,Ca,Zn,Cd,Mn,Co,Li)体系的合成、结构和Eu~(2+)在其中的发光

在BaMAl10O17 体系中 ,将M扩大到除镁以外的其它离子 ,研究和讨论了离子半径与基质结构的形成关系 ,提出能稳定(形成)尖晶石结构的M离子有相应的磁铅矿或β Al2O3 结构的化合物存在的思想 ,并研究了Eu2 +在体系中的发光性能。结果表明 ,M=Zn,Cd,Mn,Co,Li时可形成 β Al2O3 结构化合物 ,M=Ca,Be时不能形成这类结构 ,Ca���成多相共存 ,Be形成一未知相 ;Eu2 +在M=Li,Be,Zn体系中具有良好的发光性能 ,发射波长450nm ,半高宽在50nm附近 ,将是一类很有前途的新的蓝色发光材料 ,Eu2 +在M=Mn的体系中存在Eu2 +和Mn2 +的同时发射 ,在M=Cd体系中 ,Eu2 +产生一双重宽带发射。对实验结果进行了合理的解释

层流恒界面池中CA-12萃取钇的质量传递动力学

用层流恒界面池研究了CA-12萃取钇的动力学。测定了搅拌速度、酸度、萃取剂浓度、温度对萃取速率的影响。测得CA-12萃取钇的活化能为48.96kJ/mol,此过程属于化学反应控制。当CA-12中加入少量的P507时,其活化能降至23.19kJ/mol。萃取过程由化学反应控制转变为扩散和化学反应混合控制。

M_2B_5O_9Cl:Eu(M=Ca,Sr,Ba)的真空紫外光谱特性的研究

采用高温固相反应法合成了M_2B_5O_9Cl:Eu(M=Ca,Sr,Ba)中荧光体,测量了荧光体的真空紫外激发光谱,研究了M_2B_5O_9Cl:Eu(M=Ca,Sr,Ba)的真空紫外光谱特性,观察到基质吸收带位于120～200 nm区域,Eu~(2+)离子的5d能级劈裂随着M~(2+)的半径的增加而减小,同时也观察到基质与稀土离子之间存在的能量传递。

Study on effect of Gd (III) speciation on Ca (II) speciation in human blood plasma by computer simulation

Ca (II) speciation and effect of Gd (III) speciation on Ca (II) speciation in human blood plasma were studied by computer simulation. [CaHCO3](-) is a predominant compound species of Ca (II). Gd (III) can compete with Ca (II) for biological molecules. The presence of Gd (III) results in a increase of concentration of free Ca (II) and a decrease of concentration of Ca (II) compounds.

La~(3+)和Gd~(3+)对鼠肝癌H-35细胞Ca~(2+)内流的影响

通过测定 4 5Ca2 +摄取初速度的变化研究了La3+和Gd3+对鼠肝癌H 3 5细胞Ca2 +内流的影响 .发现低浓度La3+和Gd3+能增加肝癌H 3 5细胞Ca2 +内流初速度达 6～ 10倍 .Ca2 +内流的初速度随Ca2 +浓度变化的动力学研究表明 ,肝癌H 3 5细胞中存在 2类Ca2 +亲和部位的通道 ,即高亲和位和低亲和位Ca2 +内流通道 ,而La3+和Gd3+刺激的肝癌H 3 5细胞则只有 1类Ca2 +亲和位通道 ,La3+和Gd3+增加高亲和位Ca2 +结合通道的Km和Vmax,而对于低亲和位的Ca2 +结合通道Ca2 +内流的作用是竞争性的.

Ca~(2+)和Tb~(3+)对白眉蝮蛇蛇毒磷脂酶A_2荧光光谱的影响

研究了金属离子Ca2+和Tb3+对长白山白眉蝮蛇蛇毒磷脂酶A2(phospholipase A2)荧光光谱的作用，发现Ca2+浓度的增加能够增强磷脂酶A2的荧光发射强度．而且Ca2+ 浓度的增大能够明显加快磷脂酶A2与其相应反应底物DPPC的反应速率．稀土离子Tb3+在低浓度条件下对磷脂酶A2起荧光淬灭作用， 而在浓度较高时能够提高磷脂酶A2荧光发射强度.