Analyze impact of context information on rate adaptation algorithm in vehicular communication

Nowadays, road safety and traffic congestion are major concerns worldwide. This is why research on vehicular communication is very vital. In static scenarios vehicles behave typically like in an office network where nodes transmit without moving and with no defined position. This paper analyses the impact of context information on existing popular rate adaptation algorithms. Our simulation was done in MATLAB by observing the impact of context information on these algorithms. Simulation was performed for both static and mobile cases.Our simulations are based on IEEE 802.11p wireless standard. For static scenarios vehicles do not move and without defined positions, while for the mobile case, vehicles are mobile with uniformly selected speed and randomized positions. Network performance are analysed using context information. Our results show that in mobility when context information is used, the system performance can be improved for all three rate adaptation algorithms. That can be explained by that with range checking, when many vehicles are out of communication range, less vehicles contend for network resources, thereby increasing the network performances. © 2013 IEEE.

Adaptive sending rate over wireless mesh networks using SNR

Wireless Mesh Networks (WMNs) have emerged as a key technology for the next generation of wireless networking. Instead of being another type of ad-hoc networking, WMNs diversify the capabilities of ad-hoc networks. Several protocols that work over WMNs include IEEE 802.11a/b/g, 802.15, 802.16 and LTE-Advanced. To bring about a high throughput under varying conditions, these protocols have to adapt their transmission rate. This paper proposes a scheme to improve channel conditions by performing rate adaptation along with multiple packet transmission using packet loss and physical layer condition. Dynamic monitoring, multiple packet transmission and adaptation to changes in channel quality by adjusting the packet transmission rates according to certain optimization criteria provided greater throughput. The key feature of the proposed method is the combination of the following two factors: 1) detection of intrinsic channel conditions by measuring the fluctuation of noise to signal ratio via the standard deviation, and 2) the detection of packet loss induced through congestion. The authors show that the use of such techniques in a WMN can significantly improve performance in terms of the packet sending rate. The effectiveness of the proposed method was demonstrated in a simulated wireless network testbed via packet-level simulation.

Cost-efficient OFDM generation at 60-GHz by heterodyne technique with direct modulation and envelope detector

A cost-effective radio over fiber system to up-convert and transmit multigigabit signals at 60 GHz is presented. A low intermediate frequency OFDM signal is used to directly modulate a laser, which is combined with an independent unmodulated laser. The generated millimeter wave frequency can be adjusted by tuning the frequency separation between the lasers. Since no external modulator is required, this technique is low-cost and it is easily integrable in a single chip. In this paper, we present numerical results showing the feasibility of generating an IEEE 802.15.3c compliant 3.5-Gbps 60-GHz OFDM. We show that received signal quality is not limited by the lasers' linewidth but by the relative intensity noise. © 2013 IEEE.

Modelagem do consumo de energia de redes de sensores sem fio usando SystemC-AMS e stateflow

This work aims at modeling power consumption at the nodes of a Wireless Sensor Network (WSN). For doing so, a finite state machine was implemented by means of SystemC-AMS and Stateflow modeling and simulation tools. In order to achieve this goal, communication data in a WSN were collected. Based on the collected data, a simulation environment for power consumption characterization, which aimed at describing the network operation, was developed. Other than performing power consumption simulation, this environment also takes into account a discharging model as to analyze the battery charge level at any given moment. Such analysis result in a graph illustrating the battery voltage variations as well as its state of charge (SOC). Finally, a case study of the WSN power consumption aims to analyze the acquisition mode and network data communication. With this analysis, it is possible make adjustments in node-sensors to reduce the total power consumption of the network.

Controle de mobilidade infraestruturado e orientado à qualidade para maximização de admissões em sistemas WiNeMO: uma abordagem definida por software

The spread of wireless networks and growing proliferation of mobile devices require the development of mobility control mechanisms to support the different demands of traffic in different network conditions. A major obstacle to developing this kind of technology is the complexity involved in handling all the information about the large number of Moving Objects (MO), as well as the entire signaling overhead required to manage these procedures in the network. Despite several initiatives have been proposed by the scientific community to address this issue they have not proved to be effective since they depend on the particular request of the MO that is responsible for triggering the mobility process. Moreover, they are often only guided by wireless medium statistics, such as Received Signal Strength Indicator (RSSI) of the candidate Point of Attachment (PoA). Thus, this work seeks to develop, evaluate and validate a sophisticated communication infrastructure for Wireless Networking for Moving Objects (WiNeMO) systems by making use of the flexibility provided by the Software-Defined Networking (SDN) paradigm, where network functions are easily and efficiently deployed by integrating OpenFlow and IEEE 802.21 standards. For purposes of benchmarking, the analysis was conducted in the control and data planes aspects, which demonstrate that the proposal significantly outperforms typical IPbased SDN and QoS-enabled capabilities, by allowing the network to handle the multimedia traffic with optimal Quality of Service (QoS) transport and acceptable Quality of Experience (QoE) over time.

Estudo e desenvolvimento de algoritmos criptográficos para redes de sensores sem fio, utilizando técnicas de programação genética

Cryptography is the main form to obtain security in any network. Even in networks with great energy consumption restrictions, processing and memory limitations, as the Wireless Sensors Networks (WSN), this is no different. Aiming to improve the cryptography performance, security and the lifetime of these networks, we propose a new cryptographic algorithm developed through the Genetic Programming (GP) techniques. For the development of the cryptographic algorithm’s fitness criteria, established by the genetic GP, nine new cryptographic algorithms were tested: AES, Blowfish, DES, RC6, Skipjack, Twofish, T-DES, XTEA and XXTEA. Starting from these tests, fitness functions was build taking into account the execution time, occupied memory space, maximum deviation, irregular deviation and correlation coefficient. After obtaining the genetic GP, the CRYSEED and CRYSEED2 was created, algorithms for the 8-bits devices, optimized for WSNs, i.e., with low complexity, few memory consumption and good security for sensing and instrumentation applications.

Estudo e desenvolvimento de algoritmos criptográficos para redes de sensores sem fio, utilizando técnicas de programação genética

Cryptography is the main form to obtain security in any network. Even in networks with great energy consumption restrictions, processing and memory limitations, as the Wireless Sensors Networks (WSN), this is no different. Aiming to improve the cryptography performance, security and the lifetime of these networks, we propose a new cryptographic algorithm developed through the Genetic Programming (GP) techniques. For the development of the cryptographic algorithm’s fitness criteria, established by the genetic GP, nine new cryptographic algorithms were tested: AES, Blowfish, DES, RC6, Skipjack, Twofish, T-DES, XTEA and XXTEA. Starting from these tests, fitness functions was build taking into account the execution time, occupied memory space, maximum deviation, irregular deviation and correlation coefficient. After obtaining the genetic GP, the CRYSEED and CRYSEED2 was created, algorithms for the 8-bits devices, optimized for WSNs, i.e., with low complexity, few memory consumption and good security for sensing and instrumentation applications.

Valutazione delle prestazioni di reti ad accesso multiplo basate su visible light communication

Nella società odierna, le telecomunicazioni costituiscono un’esigenza fondamentale della vita quotidiana. Difatti, il mercato della ICT (Information and Communications Technology) è in costante espansione, e viene accompagnato da un rapido sviluppo di nuove tecnologie. In particolare, si assiste a un sempre più rilevante ruolo svolto dalle comunicazioni ottiche, ovvero sfruttanti la luce: in questo contesto, il quale comprende diversi rami ingegneristici, si stanno progressivamente affermando nuove forme di comunicazione basate sulla luce visibile, la cosiddetta Visible Light Communication (VLC). Con questa Tesi ci si propone di implementare con Simulink e stateflow di Matlab il livello MAC (Medium Access Control), basato sullo standard IEEE 802.15.7 per le VLC e valutarne le prestazioni. Prescinde da questa Tesi la parte di implementazione su scheda stessa che è lasciata per sviluppi futuri. Nel capitolo uno si introducono le VLC e si discutono i principali scenari attuali dove possono diffondersi. Nel capitolo 2, si mostrano le principali linee guida afferenti agli standard che sono risultate necessarie per sviluppare lo strato MAC. Nei capitoli 3 e 4 si mostra come il layer sviluppato possa essere utilizzato in due principali situazioni: nel capitolo 3 è descritta la realizzazione di una comunicazione punto-punto, ovvero con un trasmettitore e un ricevitore; nel capitolo 4 è descritta l’implementazione di una rete di nodi, ambito in cui il livello MAC risulta indispensabile. Per ognuna delle situazioni si illustrano scelte e caratteristiche dei sistemi simulati e i risultati ottenuti, cercando di coprire diverse eventualità che intercorrono, più in generale, nella gestione e implementazione di sistemi di telecomunicazione wireless.

Variable 360° Vector-Sum Phase Shifter With Coarse and Fine Vector Scaling

A CMOS vector-sum phase shifter covering the full 360° range is presented in this paper. Broadband operational transconductance amplifiers with variable transconductance provide coarse scaling of the quadrature vector amplitudes. Fine scaling of the amplitudes is accomplished using a passive resistive network. Expressions are derived to predict the maximum bit resolution of the phase shifter from the scaling factor of the coarse and fine vector-scaling stages. The phase shifter was designed and fabricated using the standard 130-nm CMOS process and was tested on-wafer over the frequency range of 4.9–5.9 GHz. The phase shifter delivers root mean square (rms) phase and amplitude errors of 1.25° and 0.7 dB, respectively, at the midband frequency of 5.4 GHz. The input and output return losses are both below 17 dB over the band, and the insertion loss is better than 4 dB over the band. The circuit uses an area of 0.303 mm2 excluding bonding pads and draws 28 mW from a 1.2 V supply.

Layering the Internet-of-Things with Multicasting in Flow-sensors for Internet-of-services

Development of Internet-of-Services will be hampered by heterogeneous Internet-of-Things infrastructures, such as inconsistency in communicating with participating objects, connectivity between them, topology definition & data transfer, access via cloud computing for data storage etc. Our proposed solutions are applicable to a random topology scenario that allow establishing of multi-operational sensor networks out of single networks and/or single service networks with the participation of multiple networks; thus allowing virtual links to be created and resources to be shared. The designed layers are context-aware, application-oriented, and capable of representing physical objects to a management system, along with discovery of services. The reliability issue is addressed by deploying IETF supported IEEE 802.15.4 network model for low-rate wireless personal networks. Flow- sensor succeeded better results in comparison to the typical - sensor from reachability, throughput, energy consumption and diversity gain viewpoint and through allowing the multicast groups into maximum number, performances can be improved.

An IP capable data link layer protocol for narrow band half-duplex packet data radio networks

The wide adaptation of Internet Protocol (IP) as de facto protocol for most communication networks has established a need for developing IP capable data link layer protocol solutions for Machine to machine (M2M) and Internet of Things (IoT) networks. However, the wireless networks used for M2M and IoT applications usually lack the resources commonly associated with modern wireless communication networks. The existing IP capable data link layer solutions for wireless IoT networks provide the necessary overhead minimising and frame optimising features, but are often built to be compatible only with IPv6 and specific radio platforms. The objective of this thesis is to design IPv4 compatible data link layer for Netcontrol Oy's narrow band half-duplex packet data radio system. Based on extensive literature research, system modelling and solution concept testing, this thesis proposes the usage of tunslip protocol as the basis for the system data link layer protocol development. In addition to the functionality of tunslip, this thesis discusses the additional network, routing, compression, security and collision avoidance changes required to be made to the radio platform in order for it to be IP compatible while still being able to maintain the point-to-multipoint and multi-hop network characteristics. The data link layer design consists of the radio application, dynamic Maximum Transmission Unit (MTU) optimisation daemon and the tunslip interface. The proposed design uses tunslip for creating an IP capable data link protocol interface. The radio application receives data from tunslip and compresses the packets and uses the IP addressing information for radio network addressing and routing before forwarding the message to radio network. The dynamic MTU size optimisation daemon controls the tunslip interface maximum MTU size according to the link quality assessment calculated from the radio network diagnostic data received from the radio application. For determining the usability of tunslip as the basis for data link layer protocol, testing of the tunslip interface is conducted with both IEEE 802.15.4 radios and packet data radios. The test cases measure the radio network usability for User Datagram Protocol (UDP) based applications without applying any header or content compression. The test results for the packet data radios reveal that the typical success rate for packet reception through a single-hop link is above 99% with a round-trip-delay of 0.315s for 63B packets.

No. 9 - Enero/Junio 2007 / SISTEMAS y TELEMATICA

Contiene: Planificación de una red DVB-H en entorno urbano David Gómez Barquero, Ariana Salieto Alexis P. García, José F. Monserrat, Narcís Cardona Incorporación de la habilidad de coordinación y del módulo de personalización de sesiones al simulador de otorrinolaringología Wesst-OT Lina María Hurtado, Oscar Darío Ramírez Mauricio Castrillón S., Angélica María Ospina C. Francisco J. Herrera Botero Andrés A. Navarro Newball, Jorge A. Vélez Beltrán GenLeNa: Sistema para la construcción de Aplicaciones de Generación de Lenguaje Natural Gloria Johanna Chala T. Rafael Armando Jordán O. Diego Luis Linares Programación básica para adolescentes Guillermo Londoño Acosta Gustavo Adolfo Paz Loboguerrero Análisis de interferencia entre las tecnologías inalámbricas Bluetooth e IEEE 802.11g Fabio Guerrero Oliver Cardona Miguel Fuertes Teoría de Sistemas: Visión trascendental de Sistemas y Espiritualidad Ricardo Schnitzler

Dissecting signaling pathways that control glia migration in the developing Drosophila retina

The function of a complex nervous system relies on an intricate interaction between neurons and glial cells. However, as glial cells are generally born distant from the place where they settle, molecular cues are important to direct their migration. Glial cell migration is important in both normal development and disease, thus current research in the laboratory has been focused on dissecting regulatory events underlying that crucial process. With this purpose, the Drosophila eye imaginal disc has been used as a model. In response to neuronal photoreceptor differentiation, glial cells migrate from the CNS into the eye disc where they act to correctly wrap axons. To ensure proper development, attractive and repulsive signals must coordinate glial cell migration. Importantly, one of these signals is Bnl, a Fibroblast Growth Factor (FGF) ligand expressed by retinal progenitor cells that was suggested to act as a non-autonomous negative regulator of excessive glial cell migration (overmigration) by binding and activating the Btl receptor expressed by glial cells. Through the experimental results described in chapter 3 we gained a detailed insight into the function of bnl in eye disc growth, photoreceptor development, and glia migration. Interestingly, we did not find a direct correlation between the defects on the ongoing photoreceptors and the glia overmigration phenotype; however, bnl knockdown caused apoptosis of eye progenitor cells what was strongly correlated with glia migration defects. Glia overmigration due to Bnl down-regulation in eye progenitor cells was rescued by inhibiting the pro-apoptotic genes or caspases activity, as well as, by depleting JNK or Dp53 function in retinal progenitor cells. Thus, we suggest a cross-talk between those developmental signals in the control of glia migration at a distance. Importantly, these results suggest that Bnl does not control glial migration in the eye disc exclusively through its ability to bind and activate its receptor Btl in glial cells. We also discuss possible biological roles for the glia overmigration in the bnl knockdown background. Previous results in the lab showed an interaction between dMyc, a master regulator of tissue growth, and Dpp, a Transforming Growth Factor-β important for retinal patterning and for accurate glia migration into the eye disc. Thus, we became interested in understanding putative relationships between Bnl and dMyc. In chapter 4, we show that they positively cooperate in order to ensure proper development of the eye disc. This work highlights the importance of the FGF signaling in eye disc development and reveals a signaling network where a range of extra- and intra-cellular signals cooperate to non-autonomously control glial cell migration. Therefore, such inter-relations could be important in other Drosophila cellular contexts, as well as in vertebrate tissue development.

Comparação do controle do inversor trifásico conectado à rede com filtro LCL considerando o amortecimento passivo e ativo

Distributed generation systems must fulfill standards specifications of current harmonics injected to the grid. In order to satisfy these grid requirements, passive filters are connected between inverter and grid. This work compares the characteristic response of the traditional inductive (L) filter with the inductive-capacitive-inductive (LCL) filter. It is shown that increasing the inductance L leads to a good ripple current suppression around the inverter switching frequency. The LCL filter provides better harmonic attenuation and reduces the filter size. The main drawback is the LCL filter impedance, which is characterized by a typical resonance peak, which must be damped to avoid instability. Passive or active techniques can be used to damp the LCL resonance. To address this issue, this dissertation presents a comparison of current control for PV grid-tied inverters with L filter and LCL filter and also discuss the use of active and passive damping for different regions of resonance frequency. From the mathematical models, a design methodology of the controllers was developed and the dynamic behavior of the system operating in closed loop was investigated. To validate the studies developed during this work, experimental results are presented using a three-phase 5kW experimental platform. The main components and their functions are discussed in this work. Experimental results are given to support the theoretical analysis and to illustrate the performance of grid-connected PV inverter system. It is shown that the resonant frequency of the system, and sampling frequency can be associated in order to calculate a critical frequency, below which is essential to perform the damping of the LCL filter. Also, the experimental results show that the active buffer per virtual resistor, although with a simple development, is effective to damp the resonance of the LCL filter and allow the system to operate stable within predetermined parameters.

Mobility in vehicular networks with multiple access points to the infrastructure

Nowadays there is a huge evolution in the technological world and in the wireless networks. The electronic devices have more capabilities and resources over the years, which makes the users more and more demanding. The necessity of being connected to the global world leads to the arising of wireless access points in the cities to provide internet access to the people in order to keep the constant interaction with the world. Vehicular networks arise to support safety related applications and to improve the traffic flow in the roads; however, nowadays they are also used to provide entertainment to the users present in the vehicles. The best way to increase the utilization of the vehicular networks is to give to the users what they want: a constant connection to the internet. Despite of all the advances in the vehicular networks, there were several issues to be solved. The presence of dedicated infrastructure to vehicular networks is not wide yet, which leads to the need of using the available Wi-Fi hotspots and the cellular networks as access networks. In order to make all the management of the mobility process and to keep the user’s connection and session active, a mobility protocol is needed. Taking into account the huge number of access points present at the range of a vehicle for example in a city, it will be beneficial to take advantage of all available resources in order to improve all the vehicular network, either to the users and to the operators. The concept of multihoming allows to take advantage of all available resources with multiple simultaneous connections. This dissertation has as objectives the integration of a mobility protocol, the Network-Proxy Mobile IPv6 protocol, with a host-multihoming per packet solution in order to increase the performance of the network by using more resources simultaneously, the support of multi-hop communications, either in IPv6 or IPv4, the capability of providing internet access to the users of the network, and the integration of the developed protocol in the vehicular environment, with the WAVE, Wi-Fi and cellular technologies. The performed tests focused on the multihoming features implemented on this dissertation, and on the IPv4 network access for the normal users. The obtained results show that the multihoming addition to the mobility protocol improves the network performance and provides a better resource management. Also, the results show the correct operation of the developed protocol in a vehicular environment.