Clinical effectiveness of direct anterior restorations-A meta-analysis.

OBJECTIVES: This is the first meta-analysis on the efficacy of composite resin restorations in anterior teeth. The objective of the present meta-analysis was to verify whether specific material classes, tooth conditioning methods and operational procedures influence the result for Class III and Class IV restorations. MATERIAL AND METHODS: The database SCOPUS and PubMed were searched for clinical trials on anterior resin composites without restricting the search to the year of publication. The inclusion criteria were: (1) prospective clinical trial with at least 2 years of observation; (2) minimal number of restorations at last recall=20; (3) report on drop-out rate; (4) report of operative technique and materials used in the trial, and (5) utilization of Ryge or modified Ryge evaluation criteria. For the statistical analysis, a linear mixed model was used with random effects to account for the heterogeneity between the studies. p-Values smaller than 0.05 were considered to be significant. RESULTS: Of the 84 clinical trials, 21 studies met the inclusion criteria, 14 of them for Class III restorations, 6 for Class IV restorations and 1 for closure of diastemata; the latter was included in the Class IV group. Twelve of the 21 studies started before 1991 and 18 before 2001. The estimated median overall success rate (without replacement) after 10 years for Class III composite resin restorations was 95% and for Class IV restorations 90%. The main reason for the replacement of Class IV restorations was bulk fractures, which occurred significantly more frequently with microfilled composites than with hybrid and macrofilled composites. Caries adjacent to restorations was infrequent in most studies and accounted only for about 2.5% of all replaced restorations after 10 years irrespective of the cavity class. Class III restorations with glass ionomer derivates suffered significantly more loss of anatomical form than did fillings with other types of material. When the enamel was acid-etched and no bonding agent was applied, significantly more restorations showed marginal staining and detectable margins compared to enamel etching with enamel bonding or the total etch technique; fillings with self-etching systems were in between of these two outcome variables. Bevelling of the enamel was associated with a significantly reduced deterioration of the anatomical form compared to no bevelling but not with less marginal staining or less detectable margins. The type of isolation (absolute/relative) had a statistically significant influence on marginal caries which, however, might be a random finding.

Bacterial adhesion efficiency on implant abutments: a comparative study

The attachment of Escherichia coli ATCC 25922 and Staphylococcus aureus ATCC 28213 onto six different materials used to manufacture dental implant abutments was quantitatively determined after 2 and 24 h of contact between the materials and the bacterial cultures. The materials were topographically characterized and their wettability determined, with both parameters subsequently related to bacterial adhesion. Atomic force microscopy, interferometry, and contact angle measurement were used to characterize the materials" surfaces. The results showed that neither roughness nor nano-roughness greatly influenced bacterial attachment whereas wettability strongly correlated with adhesion. After 2 h the degree of E. coli attachment markedly differed depending on the material whereas similar differences were not observed for S. aureus, which yielded consistently higher counts of adhered cells. Nevertheless, after 24 h the adhesion of the two species to the different test materials no longer significantly differed, although on all surfaces the numbers of finally adhered E. coli were higher than those of S. aureus

Alcatrão ou creosoto de eucalipto na produção de adesivos fenólicos para colagem de madeira

This study has shown that Eucalyptus tar and creosote can be used in phenolic adhesive formulations (resols) for wood products bonding. Some adhesives were prepared substituting 0; 17.7; 35.0 and 67.0% of the phenol by anhydrous tar and 0; 15.0 e 28.5% by creosote. In gluing Brazilian pine veneers, eucalypt tar and creosote based adhesives required longer pressing times for curing than conventional phenol-formaldehyde adhesives. By using 13C NMR, the number of carbons in side chains and hydroxyl, carbonyl, carboxyl and methoxyl groups related to 100 aromatic rings could be estimated in tar and creosote. In creosote, after reaction with excess formaldehyde in alkaline medium, only 0,28 hydroxymethyl groups was detected per phenolic ring. This low amount of hydroxymethylation explains the lack of reactivity in curing observed when creosote was introduced in a standard adhesive formulation.

Joseph Neng Shun Kwong: a famous and obscure scientist

Many students and professionals in chemistry and chemical engineering related the name Kwong with one of the most remarkable equations of state with two parameters. In the same way, very few people know who Kowng was. This article shows some of the unknown personal and professional facts of Joseph Neng Shun Kwong, a person who devoted almost four decades of his life to the industrial research in the adhesives industry.

Adhesivos tipo poliuretano obtenidos a partir de aceite de ricino y almidón químicamente modificados

This study reports the preparation of polyurethane adhesives using polyols obtained from castor oil modified by a transesterification reaction with pentaerythritol and starch modified by glycosylation. The physical properties of the polyols such as hydroxyl value were determined and the infrared spectroscopic analysis of the polyols reported. The effect of varying the hydroxyl value in the polyols on physical properties of polyurethane coatings on wood and steel panels was determined. The characterization of polyurethane coatings carried out by IR spectroscopic analysis, scratch hardness resistance, impact resistance, lap shear strength, T-peel strength measurements, solvent resistance and chemical resistant determination were reported.

Pinnoiteteollisuudessa syntyvien maalijätteiden hyötykäyttö ja uudet liiketoimintamahdollisuudet

Tämän diplomityön tavoite on kartoittaa maalien ja lakkojen valmistuksessa syntyvien sivuvirtojen hyötykäyttöä ja hyötykäyttöpotentiaalia nykyisellään. Työn tarkoitus on toimia esiselvityksenä pinnoiteteollisuuden sivuvirtojen hyötykäyttöön liittyvien liiketoimintamahdollisuuksien syvemmälle analyysille. Teollisuuden sivuvirtoihin liittyvää tietoa kerätään tilastoista ja olemassa olevista raporteista sekä haastattelemalla teollisuus- ja palveluyritysten edustajia sekä alan asiantuntijoita. Sivuvirtojen teknisten hyötykäyttömahdollisuuksien ja liiketoiminnallisten mahdollisuuksien tarkastelua varten järjestetään työpajoja asiantuntijoille Apila Group Oy Ab:n asiantuntijaverkostossa. Neljässä haastatellussa tuotantolaitoksissa syntyi vuonna 2008 yhteensä 6 662 tonnia kiinteää jätettä ja lietteitä. 68 % näistä sivuvirroista hyötykäytettiin energiana tai polttoaineen valmistuksessa. Materiaalina sivuvirtoja hyötykäytettiin 16 % sivuvirroista, pääasiassa pahvia, paperia, metalleja sekä tynnyreitä ja kontteja. Myös merkittävä osa liuottimista otettiin talteen uudelleenhyödyntämistä varten. Tässä diplomityössä hyötykäyttömahdollisuuksien tarkempaa tarkastelua varten valittiin tavanomaisiksi jätteiksi luokiteltuja maalisivuvirtoja, joita haastatelluissa tuotantolaitoksissa syntyi noin 1 500 tonnia. Maalisivuvirtojen tärkeimmät materiaaliominaisuudet liittyvät niiden sisältämiin täyte- ja sideaineisiin, jotka muodostavat merkittävän osan maalien koostumuksesta. Selvityksen mukaan nämä ominaisuudet voidaan ottaa hyötykäyttöön erilaisissa yhdistelmämateriaaleissa, esimerkiksi ekstruusiopuristetuissa tai ahtopuristetuissa muovikuitukomposiiteissa. Komposiittien raaka-aineena käytetään jo erilaisia sivuvirtoja ja lisäksi erilaisten komposiittien markkinoiden ennustetaan kasvavan. Tämä voi tarjota mahdollisuuksia uusille palvelu-, t&k- tai tuotteistusliiketoiminnoille. Kuivilla maalijätteillä on myös hyvä lämpöarvo, jolloin energiahyötykäytön ja palamisjäännöksen materiaalihyötykäytön yhdistäminen mm. keramiikka- tai sementtiteollisuudessa voi tarjota mahdollisuuksia uusille liiketoiminnoille.

Lämpötilamuutosten vaikutukset metallien liimaliitoksiin

Diplomityön tavoitteena oli tutkia lämpötilan ja sen muutosten vaikutusta kahden metallin tai metallin ja magneetin väliseen liimaliitokseen. Tutkimuksen päätavoitteena oli tutkia magneettien liimaukseen käytetyn akryyliliiman lujuutta lämpösyklitysten jälkeen ja eri käyttölämpötilojen seurauksena. Teoriaosassa on käsitelty erilaisia liimauksen toteutukseen ja liimaliitoksen lujuuteen vaikuttavia tekijöitä. Erilaiset metallien liimaukseen soveltuvat liimatyypit ja niiden tarttumiseen liittyvät tekijät, kuten esikäsittelyt on myös käyty läpi teoriaosassa. Myös liiman- ja liimatyypin valintaa koskevia periaatteita ja tekniikoita on käsitelty. Käytännön osassa on esitelty koejärjestelyt sekä tutkittavat materiaalit ja niille suoritetut esikäsittelyt. Käytännön kokeissa suoritettavissa liimaliitoksissa käytettiin akryyli- ja silikoniliimoja, joille suoritettiin erilaisia vetokokeita. Akryyliliimalla liimatuille liitoksille suoritettiin myös lämpösyklityksiä, joita vertailtiin käsittelemättömiin liitoksiin. Magneettien ja metallien välisten liitosten lujuuden lisäksi liimalta saavutettavia lujuuksia arvioitiin rakenneterästen välisen liimaliitoksen sisältävillä vetosauvoilla. Suoritettujen kokeiden perusteella havaittiin lämpötilan vaikuttavan radikaalisesti liimaliitosten lujuuteen. Magneettien liimaliitoksilla saavutettiin käytännön sovellukseen riittävän suuria leikkauslujuuden arvoja vain huoneenlämpötilassa vedettäessä. Lämpösyklitysten todettiin myös heikentävän liitosta selvästi. Silikoniliiman lujuus oli alle sovelluskohteessa vaikuttavien voimien optimaalisissakin olosuhteissa. Metallien välisten liimaliitosten lujuuden todettiin heikentyvän nopeasti kasvatettaessa vetokokeissa käytettyä lämpötilaa. Liitoksen heikkenemistä havaittiin myös lämpötilaa laskettaessa.

Rigid Rod Polymer Fillers in Acrylic Denture and Dental Adhesive Resin Systems

Polymeric materials have been used in dental applications for decades. Adhesion of polymeric materials to each other and to the tooth substrate is essential to their successful use. The aim of this series of studies was two-folded. First, to improve adhesion of poly(paraphenylene) based rigid rod polymer (RRP) to other dental polymers, and secondly, to evaluate the usability of a new dentin primer system based on RRP fillers. Poly(paraphenylene) based RRP would be a tempting material for dental applications because of its good mechanical properties. To be used in dental applications, reliable adhesion between RRP and other dental polymers is required. In this series of studies, the adhesion of RRP to denture base polymer and the mechanical properties of RRP-denture base polymer-material combination were evaluated. Also adhesion of BisGMA-TEGDMA-resin to RRP was determined. Different surface treatments were tested to improve the adhesion of BisGMA-TEGDMA-resin to RRP. Results were based on three-point bending testing, Vickers surface hardness test and scanning electron microscope analysis (SEM), which showed that no reliable adhesion between RRP and denture base polymer was formed. Addition of RRP filler to denture base polymer increased surface hardness and flexural modulus but flexural strength decreased. Results from the shear bond strength test and SEM revealed that adhesion between resin and RRP was possible to improve by surface treatment with dichloromethane (DCM) based primer and a new kind of adhesive surface can be designed. The current dentin bonding agents have good immediate bond strength, but in long term the bond strength may decrease due to the detrimental effect of water and perhaps by matrix metalloproteinases. This leads to problems in longevity of restorations. Current bonding agents use organic monomers. In this series of studies, RRP filled dentin primer was tested in order to decrease the water sorption of the monomer system of the primers. The properties of new dentin primer system were evaluated in vitro by comparing it to commercial etch and rinse adhesive system. The results from the contact angle measurements and SEM showed that experimental primer with RRP reinforcement provided similar resin infiltration to dentin collagen and formed the resin-dentin interface as the control primer. Microtensile bond strength test and SEM revealed that in short term water storing, RRP increased bond strength and primer with BMEP-monomer (bis[2-(methacryloyloxy)-ethyl]phosphate) and high solvent concentration provided comparable bonding properties to the commercial control primers. In long term water storing, the high solvent-monomer concentration of the experimental primers decreased bond strength. However, in low solvent-monomer concentration groups, the long-term water storing did not decrease the bond strength despite the existence of hydrophilic monomers which were used in the system. These studies demonstrated that new dentin primer system reached the mechanical properties of current traditional etch and rinse adhesive system in short time water storing. Improved properties can be achieved by further modifications of the monomer system. Studies of the adhesion of RRP to other polymers suggest that adhesion between RRP and other dental polymers is possible to obtain by certain surface treatments.

Influence of Heat Treatment on Strength Properties of Finger-jointed Components

The purpose for the thesis was to study the thermo treatment of finger-jointed wood. The thesis concentrated on examining the tensile and bending strength of finger-jointed and thermo treated wood. The aim was to find out how different treatment temperature levels and adhesives influence the strength of wood that has been finger-jointed before heat treatment. Secondary objectives were to examine the influence of the treatment time at one temperature, determine differences in the strength between the joints in heartwood and sapwood, examine the visual appearance of the finger joints after the treatment and establish possibilities to reach a characteristic strength level corresponding to C14. Only minor differences in strength properties were measured between the finger-jointed wood treatments II and III. A greater difference was shown between these two treatment temperatures I, which lead to reduced strength. The average strength of joints glued with adhesive 2 was higher after treatments II and III compared to those glued with the adhesive 1. At the treatment temperature I, the adhesive 1 strength properties were at the same level compared to the adhesive 2 or better. There were not any significant differences.

Teippaaminen ja liimaaminen teräsrakenteissa

Mekaanisten liittämismenetelmien ja hitsaamisen lisäksi teippaamista ja liimaamista voidaan käyttää myös teräsrakenteissa. Sillä on omat hyvät ja huonot puolensa, joita tässä työssä käydään erilaisten teippien ja liimojen sovelluskohteita tarkastelemalla. Työn tavoitteena on tutkia yleisesti teippejä ja liimoja. Lisäksi työssä on tarkoitus selvittää, soveltuuko liima- tai teippiliitos teollisuusnosturin kaapelikourun liittämiseksi kuormapalkin uumaan.

Characterization and Investigation on Material Compatibilities of Building Integrated Photovoltaic Module Components

Building Integrated Photovoltaics (BIPV) are considered as the future of photovoltaic (PV) technology. The advantage of BIPV system is its multi-functionality; they fulfil the functions of a building envelope with the added benefit of generating power by replacing the traditional roofing and façade materials with PV that generate power. In this thesis, different types of PV cells and modules have been described in detail with their efficiencies and usage trends in the last decade. The different BIPV products for roof and façade are discussed in detail giving several examples. The electricity generation potential of BIPV in selected countries is compared with their actual electricity consumption. Further, the avoided greenhouse gas (GHG) emissions associated with electricity generation from traditional sources and transportation and distribution (T&D) losses are calculated. The results illustrate huge savings in GHGs. In BIPV different types of façade and backsheets are used. In this thesis, selected backsheets and façade were characterized in terms of their surface structure identification using infrared spectroscopy (FTIR-ATR), scanning electron microscopy with energy dispersive X-ray (SEM-EDX) and physical characterization using surface energy measurements. By using FTIR-ATR, surface polymeric materials were identified and with SEM-EDX, identification of the surface elements was possible. Surface energy measurements were useful in finding the adhesives and knowing the surface energies of the various backsheets and façade. The strength of adhesion between the facade and backsheets was studied using peel test. Four different types of adhesives were used to study the fracture pattern and peel tests values to identify the most suitable adhesive. It was found out that pretreatment increased the adhesive strength significantly.

Simulation de profils de gravure et de dépôt à l’échelle du motif pour l’étude des procédés de microfabrication utilisant une source plasma de haute densité à basse pression

En lien avec l’avancée rapide de la réduction de la taille des motifs en microfabrication, des processus physiques négligeables à plus grande échelle deviennent dominants lorsque cette taille s’approche de l’échelle nanométrique. L’identification et une meilleure compréhension de ces différents processus sont essentielles pour améliorer le contrôle des procédés et poursuivre la «nanométrisation» des composantes électroniques. Un simulateur cellulaire à l’échelle du motif en deux dimensions s’appuyant sur les méthodes Monte-Carlo a été développé pour étudier l’évolution du profil lors de procédés de microfabrication. Le domaine de gravure est discrétisé en cellules carrées représentant la géométrie initiale du système masque-substrat. On insère les particules neutres et ioniques à l’interface du domaine de simulation en prenant compte des fonctions de distribution en énergie et en angle respectives de chacune des espèces. Le transport des particules est effectué jusqu’à la surface en tenant compte des probabilités de réflexion des ions énergétiques sur les parois ou de la réémission des particules neutres. Le modèle d’interaction particule-surface tient compte des différents mécanismes de gravure sèche telle que la pulvérisation, la gravure chimique réactive et la gravure réactive ionique. Le transport des produits de gravure est pris en compte ainsi que le dépôt menant à la croissance d’une couche mince. La validité du simulateur est vérifiée par comparaison entre les profils simulés et les observations expérimentales issues de la gravure par pulvérisation du platine par une source de plasma d’argon.

Studies on Rubber-to-Nylon Tire Cord Bonding

ABSTRACT: Nylon tire cord (1680/2) was dipped in different adhesives based on resorcinol formaldehyde resin and latex (RFL) and was bonded to natural rubber-based compounds. The resin-rubber ratio in the RFL adhesive was optimized. The variation of pull-through load was studied by varying the drying and curing temperature of the dipped nylon tire cord. RFL adhesive based on vinylpyridine latex was found to have better rubber-to-nylon tire cord bonding, compared with the one based on natural rubber latex. Addition of a formaldehyde donor into the RFL adhesive/rubber compound improves adhesion.

Novel adhesive systems based on neoprene-phenolic blends

The aim of the investigation is to develop new high performance adhesive systems based on neoprene-phenolic blends. Initially the effect of addition of all possible ingredients like fillers, adhesion promoters, curing agents and their optimum compositions to neoprene solution is investigated. The phenolic resin used is a copolymer of phenol-cardanolformaldehyde prepared in the laboratory. The optimum ratio between phenol and cardanol that gives the maximum bond strength in metal-metal, rubber-rubber and rubber-metal specimens has been identified. Further the ratio between total phenols and formaldehyde is also optimised. The above adhesive system is further modified by the addition of epoxidized phenolic novolacs. For this purpose, phenolic novolac resins are prepared in different stoichiometric ratios and are subsequently epoxidized. The effectiveness of the adhesive for bonding different metal and rubber substrates is another part of the study. To study the ageing behaviour, different bonded specimens are exposed to high temperature, hot water and salt water and adhesive properties have been evaluated. The synthesized resins have been characterized by FTIR , HNMR spectroscopy. The molecular weights of the resins have been obtained by GPC. Thermogravimetric analysis and differential scanning calorimetry are used to study the thermal properties. The fractured surface analysis is studied by scanning electron microscopy. The study has brought to light the influence of phenol/ formaldehyde stoichiometric ratio, addition of cardanol (a renewable resource), adhesion promoters and suitability of the adhesive for different substrates and the age resistance of adhesive joints among other things.

Novel applications of cashew nut shell liquid in the polymer field

This research project aims at developing new applications for CNSL in the polymer field. Cashew nut shell liquid (CNSL) is a cheap agro-byproduct and renewable resource which consists mainly of substituted phenols. By using CNSL in place of phenol, phenol derived from petrochemicals can be conserved and a cheap agro-byproduct utilized.In this study CNSL based resin is prepared by condensing a mixture of phenol and CNSL with hexamethylenetetramine and the effect of P: F ratio and CNSL: P ratio on the properties of synthesized resin is studied. The adhesive properties of CNSL based resin in combination with neoprene rubber are investigated. The effect of varying the stoichiometric ratios between total phenol and formaldehyde and CNSL and phenol of the resin, resin content, choice and extent of fillers and adhesion promoters in the adhesive formulation are studied. The effect of resin on the ageing properties of various elastomers is also studied by following changes in tensile strength, elongation at break, modulus, tear strength, swelling index and acetone soluble matter. Crude CNSL and resins with different P: F ratios and CNSL: P ratios are incorporated into elastomers. Lastly, utility of CNSL based resin as binder for making particleboard is investigated.The results show that CNSL based resin is an effective ingredient in adhesives for bonding aluminium to aluminium. The resin used for adhesive fonnulation gives the best performance at 45 to 55 phr resin and a total phenol: formaldehyde of l:2.9. The resin when added at a rate of l5 phr improves ageing characteristics of elastomers with respect to mechanical properties. The reaction mixture of CNSL and hexa and the resin resulting from the condensation of CN SL, phenol and hexa can be used as effective binders for moulding particleboard.