Using CAD parameter sensitivities for stack-up tolerance allocation

Tolerance allocation is an important step in the design process. It is necessary to produce high quality components cost-effectively. However, the process of allocating tolerances can be time consuming and difficult, especially for complex models. This work demonstrates a novel CAD based approach, where the sensitivities of product dimensions to changes in the values of the feature parameters in the CAD model are computed. These are used to automatically establish the assembly response function for the product. This information has been used to automatically allocate tolerances to individual part dimensions to achieve specified tolerances on the assembly dimensions, even for tolerance allocation in more than one direction simultaneously. It is also shown how pre-existing constraints on some of the part dimensions can be represented and how situations can be identified where the required tolerance allocation is not achievable. A methodology is also presented that uses the same information to model a component with different amounts of dimensional variation to simulate the effects of tolerance stack-up. © 2014 Springer-Verlag France.

Stress tolerance and virulence of insect-pathogenic fungi are determined by environmental conditions during conidial formation

The virulence to insects and tolerance to heat and UV-B radiation of conidia of entomopathogenic fungi are greatly influenced by physical, chemical, and nutritional conditions during mycelial growth. This is evidenced, for example, by the stress phenotypes of Metarhizium robertsii produced on various substrates. Conidia from minimal medium (Czapek's medium without sucrose), complex medium, and insect (Lepidoptera and Coleoptera) cadavers had high, moderate, and poor tolerance to UV-B radiation, respectively. Furthermore, conidia from minimal medium germinated faster and had increased heat tolerance and were more virulent to insects than those from complex medium. Low water-activity or alkaline culture conditions also resulted in production of conidia with high tolerance to heat or UV-B radiation. Conidia produced on complex media exhibited lower stress tolerance, whereas those from complex media supplemented with NaCl or KCl (to reduce water activity) were more tolerant to heat and UV-B than those from the unmodified complex medium. Osmotic and nutritive stresses resulted in production of conidia with a robust stress phenotype, but also were associated with low conidial yield. Physical conditions such as growth under illumination, hypoxic conditions, and heat shock before conidial production also induced both higher UV-B and heat tolerance; but conidial production was not decreased. In conclusion, physical and chemical parameters, as well as nutrition source, can induce great variability in conidial tolerance to stress for entomopathogenic fungi. Implications are discussed in relation to the ecology of entomopathogenic fungi in the field, and to their use for biological control. This review will cover recent technologies on improving stress tolerance of entomopathogenic fungi for biological control of insects.

Chaotropicity: a key factor in product tolerance of biofuel-producing microorganisms

Fermentation products can chaotropically disorder macromolecular systems and induce oxidative stress, thus inhibiting biofuel production. Recently, the chaotropic activities of ethanol, butanol and vanillin have been quantified (5.93, 37.4, 174kJkg(-1)m(-1) respectively). Use of low temperatures and/or stabilizing (kosmotropic) substances, and other approaches, can reduce, neutralize or circumvent product-chaotropicity. However, there may be limits to the alcohol concentrations that cells can tolerate; e.g. for ethanol tolerance in the most robust Saccharomyces cerevisiae strains, these are close to both the solubility limit (<25%, w/v ethanol) and the water-activity limit of the most xerotolerant strains (0.880). Nevertheless, knowledge-based strategies to mitigate or neutralize chaotropicity could lead to major improvements in rates of product formation and yields, and also therefore in the economics of biofuel production.

Extraordinary solute-stress tolerance contributes to the environmental tenacity of mycobacteria

Mycobacteria are associated with a number of well-characterized diseases, yet we know little about their stress-biology in natural ecosystems. This study focuses on the isolation and characterization of strains from Yellowstone-(YNP) and Glacier-National-Parks (GNP; USA), the majority of those identified were Mycobacterium parascrofulaceum, Mycobacterium avium (YNP) or Mycobacterium gordonae (GNP). Generally, their temperature windows for growth were >60°C; selected isolates grew at super-saturated concentrations of hydrophobic stressors and at levels of osmotic stress and chaotropic activity (up to 13.4 kJkg-1) similar to, or exceeding, those for the xerophilic fungus Aspergillus wentii and solvent-tolerant bacterium Pseudomonas putida. For example, mycobacteria grew down to 0.800 water-activity indicating that they are, with the sole exception of halophiles, more xerotolerant than other bacteria (or any Archaea). Furthermore, the fatty-acid composition of Mycobacterium cells grown over a range of salt concentrations changed less than that of other bacteria, indicating a high level of resilience, regardless of the stress load. Cells of M. parascrofulaceum, M. smegmatis and M. avium resisted the acute, potentially lethal challenges from extremes of pH (<1; >13), and saturated MgCl2-solutions (5 M; 212 kJ kg-1 chaotropicity). Collectively, these findings challenge the paradigm that bacteria have solute tolerances inferior to those of eukaryotes.

Performance and Fault Tolerance of Preconditioned Iterative Solvers on Low-Power ARM Architectures

As the complexity of computing systems grows, reliability and energy are two crucial challenges asking for holistic solutions. In this paper, we investigate the interplay among concurrency, power dissipation, energy consumption and voltage-frequency scaling for a key numerical kernel for the solution of sparse linear systems. Concretely, we leverage a task-parallel implementation of the Conjugate Gradient method, equipped with an state-of-the-art pre-conditioner embedded in the ILUPACK software, and target a low-power multi core processor from ARM.In addition, we perform a theoretical analysis on the impact of a technique like Near Threshold Voltage Computing (NTVC) from the points of view of increased hardware concurrency and error rate.

Arsenate, arsenite and dimethyl arsinic acid (DMA) uptake and tolerance in maize (Zea mays L.)

The influx of arsenate, arsenite and dimethyl arsinic acid (DMA) were studied in 7-day-old excised maize roots (Zea mays L.), and then related to arsenate, arsenite and DMA toxicity. Arsenate, arsenite and DMA influx was all found concentration dependent with significant genotypic differences for arsenite and DMA. Arsenate influx in phosphate starved plants best fitted the four-parameter Michaelis-Menten model corresponding to an additive high and low affinity uptake system, while the uptake of phosphate replete plants followed the two parameter model of Michaelis-Menten kinetics. Arsenite influx was well described by the two parameter model of 'Michaelis-Menten' kinetics. DMA influx was comprised of linear phase and a hyperbolic phase. DMA influx was much lower than that for arsenite and arsenate. Arsenate and DMA influx decreased when phosphate was given as a pre-treatment as opposed to phosphate starved plants. The +P treatment tended to decrease influx by 50% for arsenate while this figure was 90% for DMA. Arsenite influx increasing slightly at higher arsenite concentrations in P starved plants but at lower arsenite concentrations, there was little or no difference in arsenite uptake. Low toxicity was found for DMA on maize compared with arsenate and arsenite and the relative toxicity of arsenic species was As(V) > As(III) >> DMA. © 2008 Springer Science+Business Media B.V.

An arsenate tolerance gene on chromosome 6 of rice

The genetics of arsenic tolerance in plants has not been extensively studied and no arsenic tolerance gene has been genetically mapped. Screening 20 diverse genotypes of rice for reduced root growth in 13.3 μM arsenate identified marked differences in tolerance. The most sensitive variety, Dawn, is known to be highly susceptible to straighthead, a condition linked to arsenic contamination of soil. Screening 108 recombinant inbred lines of the Bala x Azucena mapping population revealed the presence of a major gene, AsTol, which mapped between markers RZ516 and RG213 on chromosome 6. This gene is a good target for further characterisation. It should prove valuable for investigations into the physiological and molecular mechanism behind arsenic tolerance in plants and may lead to strategies aimed at breeding for arsenic contaminated regions. © New Phytologist (2004).

Yellow earthworms:Distinctive pigmentation associated with arsenic- and copper-tolerance in Lumbricus rubellus

Lumbricus rubellus Hoffmeister, inhabiting soil at the 19th century Devon Great Consols mine at Tavistock, Devon, UK, show high tolerance to Cu- and As-toxicity and frequently have a striking yellow coloration. Specimens from this site (mature and immature) and from an uncontaminated site on Lancaster University campus (mature) were photographed, and the slide images digitized and analyzed. All L. rubellus showed reddish-purple pigmentation of the body wall that declined in intensity posteriorly. The metal- and metalloid-resistant earthworms, whether mature or immature, showed yellowing in the posterior half of the body. The source of the coloration was intense yellow pigmentation of the chloragogenous tissue surrounding the alimentary canal. The yellow pigmentation is masked by reddish-purple body wall pigmentation anteriorly. Total As concentrations in tissues were determined for the anterior, middle and posterior sections of resistant and non-resistant L. rubellus. Highest concentrations were in the middle sections of the mature and immature resistant L. rubellus (36.17 ± 19.77 and 27.77 ± 9.02 mg As kg^-1, respectively). Resistant immature L. rubellus lost condition over 28 d in soil treated with 750 mg As kg^-1, possibly due to a higher metabolism, whilst there was no loss in condition for resistant mature L. rubellus in the treated soil. As far as the authors are aware, this is the first report of yellow pigmentation of this kind in earthworms. The pigmentation may provide a useful indicator of exposure/resistance to soil contamination. © 2002 Elsevier Science Ltd. All rights reserved.

Do ectomycorrhizal fungi exhibit adaptive tolerance to potentially toxic metals in the environment?

The effects of potentially toxic metals on ectomycorrhizal (ECM) fungi and their higher plant hosts are examined in this review. Investigations at a species and community level have revealed wide inter- and intraspecific variation in sensitivity to metals. Adaptive and constitutive mechanisms of ECM tolerance are proposed and discussed in relation to proven tolerance mechanisms in bacteria, yeasts and plants. Problems with methodology and research priorities are highlighted. These include the need for a detailed understanding of the genetic basis of tolerance in the ECM symbiosis, and for studies of ECM community dynamics in polluted sites.

Relationship between plant phosphorus status and the kinetics of arsenate influx in clones of deschampsia cespitosa (L.) beauv. that differ in their tolerance to arsenate

Uptake kinetics of arsenate were determined in arsenate tolerant and non-tolerant clones of the grass Deschampsia cespitosa under differing root phosphorus status to investigate the mechanism controlling the suppression of arsenate influx observed in tolerant clones. Influx was always lower in tolerants compared to non-tolerants. Short term influx of arsenate by the high affinity uptake system in both tolerant clones was relatively insensitive to root phosphorus status. This was in contrast to the literature where the regulation of the phosphate (arsenate) uptake system is normally much more responsive to plant phosphorus status. The low affinity uptake system in both tolerant and non-tolerant clones, unlike the high affinity uptake system, was more closely regulated by root phosphate status and was repressed to a much greater degree under increasing root phosphorus levels than the high affinity system. © 1994 Kluwer Academic Publishers.