Sistema inalámbrico de control de iluminación

L’objectiu principal del projecte és dissenyar un sistema de control automàtic de il·luminació en un recinte tancat, mitjançant la detecció de presència d’una persona que entra dins del radi d’actuació del sistema. Utilitzant dues plaques amb capacitat de comunicació inalàmbrica es controlaran dos components, un sensor i un actuador. El sensor té la funció de detectar la presència d’una persona per mitjà d’infraroigs, mentre que l’actuador ens proporciona la funcionalitat d’un interruptor amb el qual pogué actuar sobre la llum, encenent-la o apagant-la en funció de l’estat de detecció.

Disseny d'un sistema HW/SW de control remot amb dispositius FPGA

El projecte que es presenta a continuació, té com a objectiu implementar un sistema HW/SW encastat en una FPGA, capaç d’executar funcions de control remot per infraroig en plataformes de televisió flexibles de Sony Corp. El disseny obtingut, s’incorporarà a un sistema més ampli de verificació i test de circuits impresos, dins del marc de producció SMD. La finalitat d’aquest projecte, és la realització d’un sistema flexible per a la implementació de comandaments de comunicació per infraroig amb circuits impresos. Prèviament, s’ha estudiat els conceptes bàsics referents a la implementació de sistemes amb FPGAs, la seva metodologia de desenvolupament i les principals característiques de la seva arquitectura. Com a especificacions, s’ha utilitzat l’estàndard de control remot per infraroig de Sony Corp SIRCS (Sony Infrared remote control system).

A biodegradable drug delivery system for the treatment of postoperative inflammation

Cataract surgery is often performed in patients suffering from associated pathologies. Our goal is to develop a biodegradable drug delivery system (DDS) combined with the artificial intraocular lens (IOL). DDS were manufactured using poly(D,L-lactide-co-glycolide), or PLGA, and were loaded with triamcinolone acetonide (TA). The loading capacity was approximately 1050 microg of TA per DDS. The higher the molecular weight of PLGA (34,000, 48,000 and 80,000Da), the slower was the release of TA in vitro. Cataract surgery was performed on the right eye of rabbits. IOL was inserted with (i) no DDS, (ii) unloaded DDS PLGA48000, (iii) one loaded DDS PLGA48000, (iv) two loaded DDS. The number of inflammatory cells and the protein concentration were measured in the aqueous humor (AH). Unloaded DDS showed good ocular biocompatibility. One DDS PLGA48000 loaded with TA significantly reduced postoperative ocular inflammation. Two loaded DDS PLGA48000 was even more effective in inhibiting such inflammation. On long-term observation (days 63 and 84), reduction of inflammation could be obtained by insertion of one DDS PLGA48000 and a second DDS PLGA80000. Therefore, our "all in one" system is very promising since it could replace oral treatment and reduce the number of intraocular injections

Disseny i implementació d'un sistema de control de projectes

Aquest treball de fi de carrera, com descriu el seu títol, consisteix a dissenyar i implementar un sistema de control de projectes. Com tot projecte, complirà el requisit de disposar d'un pla que permeti fer un seguiment dels terminis d'execució, de les fites establertes i un control dels lliurables identificats. Pel fet de tractar-se del desenvolupament d'un sistema informàtic, considerarà les etapes d'especificació de requisits, anàlisi, disseny, codificació, proves unitàries i proves funcionals, i es generaran els informes pertinents que serveixin de documentació i de referència en les etapes posteriors. Des d'un punt de vista tecnològic, permetrà aprofundir en el coneixement de l'estructura de funcionament del PL/SQL d'Oracle (crides a procediments i, especialment, al tractament).

Diseño e Implementación de un Sistema de Control de Proyectos

Aquest treball de final de carrera té com a objectiu fer el disseny i la implementació d'un sistema de control de projectes per a una organització, de manera que la seva estructura interna i funcionament segueixin els paràmetres especificats a l'enunciat proporcionat per la consultora de l'assignatura. El sistema ha de recollir informació sobre quan de temps i en què treballa cada treballador, i quines han estat les despeses mentre ha estat assignat a cada projecte o tasca. D'aquesta manera, a més de tenir un control horari del treballador, l'organització sabrà perfectament si la realització d'un projecte ha estat rendible i disposarà, durant el desenvolupament, de dades sobre l'evolució de costos i hores per a executar les actuacions correctives pertinents.

Disseny i implementació d'un sistema de control de projectes

L'objectiu d'aquest treball és fer el disseny i la implementació d'un sistema de control de projectes per a una organització X, de manera que la seva estructura i funcionament compleixin uns requisits inicials.

Control de dispositivos con Android

Este proyecto de final de carrera de la titulación de Ingeniería en Informática de Gestión consiste en el diseño y desarrollo de un sistema de control de dispositivos conectados a Raspberry Pi y gestionados desde un dispositivo Android. Se podrán llevar a cabo diferentes acciones como encender, apagar, programar la calefacción y consultar la temperatura actual remotamente desde un dispostivo conectado a la red wifi doméstica o desde de cualquier red que esté conectada a internet.

Converter-flux-based current control of voltage source PWM rectifiers - analysis and implementation

Pulsewidth-modulated (PWM) rectifier technology is increasingly used in industrial applications like variable-speed motor drives, since it offers several desired features such as sinusoidal input currents, controllable power factor, bidirectional power flow and high quality DC output voltage. To achieve these features,however, an effective control system with fast and accurate current and DC voltage responses is required. From various control strategies proposed to meet these control objectives, in most cases the commonly known principle of the synchronous-frame current vector control along with some space-vector PWM scheme have been applied. Recently, however, new control approaches analogous to the well-established direct torque control (DTC) method for electrical machines have also emerged to implement a high-performance PWM rectifier. In this thesis the concepts of classical synchronous-frame current control and DTC-based PWM rectifier control are combined and a new converter-flux-based current control (CFCC) scheme is introduced. To achieve sufficient dynamic performance and to ensure a stable operation, the proposed control system is thoroughly analysed and simple rules for the controller design are suggested. Special attention is paid to the estimationof the converter flux, which is the key element of converter-flux-based control. Discrete-time implementation is also discussed. Line-voltage-sensorless reactive reactive power control methods for the L- and LCL-type line filters are presented. For the L-filter an open-loop control law for the d-axis current referenceis proposed. In the case of the LCL-filter the combined open-loop control and feedback control is proposed. The influence of the erroneous filter parameter estimates on the accuracy of the developed control schemes is also discussed. A newzero vector selection rule for suppressing the zero-sequence current in parallel-connected PWM rectifiers is proposed. With this method a truly standalone and independent control of the converter units is allowed and traditional transformer isolation and synchronised-control-based solutions are avoided. The implementation requires only one additional current sensor. The proposed schemes are evaluated by the simulations and laboratory experiments. A satisfactory performance and good agreement between the theory and practice are demonstrated.

Design,implementation and use of an Internet kiosk as an an information system for CNC machinists

Tätä diplomityötä sponsoroi suuri Isobritannialainen lentokoneteollisuudessa toimiva yritys, joka huomasi että globaalin tuotantostrategian ollessa painopisteenä ja tietoteknisten järjestelmien kuten CAD/CAM ollessa merkittävänä osana tuotantoa, on löydettävä ymmärrys siitä, mitkä ovat tuotannon tietojärjestelmien tarpeet ja onko niiden kehittämisestä hyötyä yritykselle.Diplomityössä selitetään Internet teknologiaan perustuvan kioskin kehittämisestä tietotukijärjestelmäksi tuotanto-osastolle, jossa valmistetaan moottorin osia CNC-koneilla. Kioskeissa on piirteitä, jotka voisivat osoittautua hyödyllisiksi myös tuotantoympäristöissä ja siksi tässä työssä tutkitaan kioskiin perustuvaa lähestymistapaa tuotantoympäristöön sovellettuna.Diplomityö kuvaa informaatiokioskin kehittämistä alkaen alkuvaatimusten keruusta tietojärjestelmää varten, tietojärjestelmän suunnittelu- ja kehitysvaiheen sekä lopuksi analysoi kioskin onnistuneisuutta tuotantoympäristössä käytettävyystutkimuksen avulla, joka suoritettiin sen jälkeen kun kioski oli implementoitu tehtaassa.Johtopäätökset osoittavat, että kioski on hyvin implementoitavissa tuotantoympäristöön ja todistaa, että tuotantoinformaation jakelu sähköisessä muodossa on huomattavasti tehokkaampaa kuin paperilla. Käyttäjien kommentit osoittavat että kioski on sopiva heidän tietotarpeisiinsa ja siitä on hyötyä heidän työlleen. Kioski tarjoaa hyötyjä tuotantotason lisäksi myös johtotasolle.

On the Analysis and Control of a Linear Synchronous Servomotor with a Flexible Load

Industry's growing need for higher productivity is placing new demands on mechanisms connected with electrical motors, because these can easily lead to vibration problems due to fast dynamics. Furthermore, the nonlinear effects caused by a motor frequently reduce servo stability, which diminishes the controller's ability to predict and maintain speed. Hence, the flexibility of a mechanism and its control has become an important area of research. The basic approach in control system engineering is to assume that the mechanism connected to a motor is rigid, so that vibrations in the tool mechanism, reel, gripper or any apparatus connected to the motor are not taken into account. This might reduce the ability of the machine system to carry out its assignment and shorten the lifetime of the equipment. Nonetheless, it is usually more important to know how the mechanism, or in other words the load on the motor, behaves. A nonlinear load control method for a permanent magnet linear synchronous motor is developed and implemented in the thesis. The purpose of the controller is to track a flexible load to the desired velocity reference as fast as possible and without awkward oscillations. The control method is based on an adaptive backstepping algorithm with its stability ensured by the Lyapunov stability theorem. As a reference controller for the backstepping method, a hybrid neural controller is introduced in which the linear motor itself is controlled by a conventional PI velocity controller and the vibration of the associated flexible mechanism is suppressed from an outer control loop using a compensation signal from a multilayer perceptron network. To avoid the local minimum problem entailed in neural networks, the initial weights are searched for offline by means of a differential evolution algorithm. The states of a mechanical system for controllers are estimated using the Kalman filter. The theoretical results obtained from the control design are validated with the lumped mass model for a mechanism. Generalization of the mechanism allows the methods derived here to be widely implemented in machine automation. The control algorithms are first designed in a specially introduced nonlinear simulation model and then implemented in the physical linear motor using a DSP (Digital Signal Processor) application. The measurements prove that both controllers are capable of suppressing vibration, but that the backstepping method is superior to others due to its accuracy of response and stability properties.

The Detector Control Systems for the CMS Resistive Plate Chamber at LHC

The RPC Detector Control System (RCS) is the main subject of this PhD work. The project, involving the Lappeenranta University of Technology, the Warsaw University and INFN of Naples, is aimed to integrate the different subsystems for the RPC detector and its trigger chain in order to develop a common framework to control and monitoring the different parts. In this project, I have been strongly involved during the last three years on the hardware and software development, construction and commissioning as main responsible and coordinator. The CMS Resistive Plate Chambers (RPC) system consists of 912 double-gap chambers at its start-up in middle of 2008. A continuous control and monitoring of the detector, the trigger and all the ancillary sub-systems (high voltages, low voltages, environmental, gas, and cooling), is required to achieve the operational stability and reliability of a so large and complex detector and trigger system. Role of the RPC Detector Control System is to monitor the detector conditions and performance, control and monitor all subsystems related to RPC and their electronics and store all the information in a dedicated database, called Condition DB. Therefore the RPC DCS system has to assure the safe and correct operation of the sub-detectors during all CMS life time (more than 10 year), detect abnormal and harmful situations and take protective and automatic actions to minimize consequential damages. The analysis of the requirements and project challenges, the architecture design and its development as well as the calibration and commissioning phases represent themain tasks of the work developed for this PhD thesis. Different technologies, middleware and solutions has been studied and adopted in the design and development of the different components and a big challenging consisted in the integration of these different parts each other and in the general CMS control system and data acquisition framework. Therefore, the RCS installation and commissioning phase as well as its performance and the first results, obtained during the last three years CMS cosmic runs, will be

Embedded controller system in crane application

The thesis studies possibility of using embedded controller in a crane application and furthermore defines requirements when designing such a controller. Basic crane control architectures are considered and compared. Then embedded controller product life cycle is described: considering such issues like microcontroller selection, software/hardware design and application development tools. Finally, available embedded controller is described and used for implementing crane control.

Phase voltage control and filtering in a converter-fed single-phase customer-end system of the LVDC distribution network

In recent years, the network vulnerability to natural hazards has been noticed. Moreover, operating on the limits of the network transmission capabilities have resulted in major outages during the past decade. One of the reasons for operating on these limits is that the network has become outdated. Therefore, new technical solutions are studied that could provide more reliable and more energy efficient power distributionand also a better profitability for the network owner. It is the development and price of power electronics that have made the DC distribution an attractive alternative again. In this doctoral thesis, one type of a low-voltage DC distribution system is investigated. Morespecifically, it is studied which current technological solutions, used at the customer-end, could provide better power quality for the customer when compared with the current system. To study the effect of a DC network on the customer-end power quality, a bipolar DC network model is derived. The model can also be used to identify the supply parameters when the V/kW ratio is approximately known. Although the model provides knowledge of the average behavior, it is shown that the instantaneous DC voltage ripple should be limited. The guidelines to choose an appropriate capacitance value for the capacitor located at the input DC terminals of the customer-end are given. Also the structure of the customer-end is considered. A comparison between the most common solutions is made based on their cost, energy efficiency, and reliability. In the comparison, special attention is paid to the passive filtering solutions since the filter is considered a crucial element when the lifetime expenses are determined. It is found out that the filter topology most commonly used today, namely the LC filter, does not provide economical advantage over the hybrid filter structure. Finally, some of the typical control system solutions are introduced and their shortcomings are presented. As a solution to the customer-end voltage regulation problem, an observer-based control scheme is proposed. It is shown how different control system structures affect the performance. The performance meeting the requirements is achieved by using only one output measurement, when operating in a rigid network. Similar performance can be achieved in a weak grid by DC voltage measurement. An additional improvement can be achieved when an adaptive gain scheduling-based control is introduced. As a conclusion, the final power quality is determined by a sum of various factors, and the thesis provides the guidelines for designing the system that improves the power quality experienced by the customer.

Modeling and Control of the Power Conversion Unit in a Solid Oxide Fuel Cell Environment

In this doctoral thesis, a power conversion unit for a 10 kWsolid oxide fuel cell is modeled, and a suitable control system is designed. The need for research was identified based on an observation that there was no information available about the characteristics of the solid oxide fuel cell from the perspective of power electronics and the control system, and suitable control methods had not previously been studied in the literature. In addition, because of the digital implementation of the control system, the inherent characteristics of the digital system had to be taken into account in the characteristics of the solid oxide fuel cell (SOFC). The characteristics of the solid oxide fuel cell as well the methods for the modeling and control of the DC/DC converter and the grid converter are studied by a literature survey. Based on the survey, the characteristics of the SOFC as an electrical power source are identified, and a solution to the interfacing of the SOFC in distributed generation is proposed. A mathematical model of the power conversion unit is provided, and the control design for the DC/DC converter and the grid converter is made based on the proposed interfacing solution. The limit cycling phenomenon is identified as a source of low-frequency current ripple, which is found to be insignificant when connected to a grid-tied converter. A method to mitigate a second harmonic originating from the grid interface is proposed, and practical considerations of the operation with the solid oxide fuel cell plant are presented. At the theoretical level, the thesis discusses and summarizes the methods to successfully derive a model for a DC/DC converter, a grid converter, and a power conversion unit. The results of this doctoral thesis can also be used in other applications, and the models and methods can be adopted to similar applications such as photovoltaic systems. When comparing the results with the objectives of the doctoral thesis, we may conclude that the objectives set for the work are met. In this doctoral thesis, theoretical and practical guidelines are presented for the successful control design to connect a SOFC-based distributed generation plant to the utility grid.

Flexible multibody dynamics and intelligent control of a hydraulically driven hybrid redundant robot machine

The assembly and maintenance of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel (VV) is highly challenging since the tasks performed by the robot involve welding, material handling, and machine cutting from inside the VV. The VV is made of stainless steel, which has poor machinability and tends to work harden very rapidly, and all the machining operations need to be carried out from inside of the ITER VV. A general industrial robot cannot be used due to its poor stiffness in the heavy duty machining process, and this will cause many problems, such as poor surface quality, tool damage, low accuracy. Therefore, one of the most suitable options should be a light weight mobile robot which is able to move around inside of the VV and perform different machining tasks by replacing different cutting tools. Reducing the mass of the robot manipulators offers many advantages: reduced material costs, reduced power consumption, the possibility of using smaller actuators, and a higher payload-to-robot weight ratio. Offsetting these advantages, the lighter weight robot is more flexible, which makes it more difficult to control. To achieve good machining surface quality, the tracking of the end effector must be accurate, and an accurate model for a more flexible robot must be constructed. This thesis studies the dynamics and control of a 10 degree-of-freedom (DOF) redundant hybrid robot (4-DOF serial mechanism and 6-DOF 6-UPS hexapod parallel mechanisms) hydraulically driven with flexible rods under the influence of machining forces. Firstly, the flexibility of the bodies is described using the floating frame of reference method (FFRF). A finite element model (FEM) provided the Craig-Bampton (CB) modes needed for the FFRF. A dynamic model of the system of six closed loop mechanisms was assembled using the constrained Lagrange equations and the Lagrange multiplier method. Subsequently, the reaction forces between the parallel and serial parts were used to study the dynamics of the serial robot. A PID control based on position predictions was implemented independently to control the hydraulic cylinders of the robot. Secondly, in machining, to achieve greater end effector trajectory tracking accuracy for surface quality, a robust control of the actuators for the flexible link has to be deduced. This thesis investigates the intelligent control of a hydraulically driven parallel robot part based on the dynamic model and two schemes of intelligent control for a hydraulically driven parallel mechanism based on the dynamic model: (1) a fuzzy-PID self-tuning controller composed of the conventional PID control and with fuzzy logic, and (2) adaptive neuro-fuzzy inference system-PID (ANFIS-PID) self-tuning of the gains of the PID controller, which are implemented independently to control each hydraulic cylinder of the parallel mechanism based on rod length predictions. The serial component of the hybrid robot can be analyzed using the equilibrium of reaction forces at the universal joint connections of the hexa-element. To achieve precise positional control of the end effector for maximum precision machining, the hydraulic cylinder should be controlled to hold the hexa-element. Thirdly, a finite element approach of multibody systems using the Special Euclidean group SE(3) framework is presented for a parallel mechanism with flexible piston rods under the influence of machining forces. The flexibility of the bodies is described using the nonlinear interpolation method with an exponential map. The equations of motion take the form of a differential algebraic equation on a Lie group, which is solved using a Lie group time integration scheme. The method relies on the local description of motions, so that it provides a singularity-free formulation, and no parameterization of the nodal variables needs to be introduced. The flexible slider constraint is formulated using a Lie group and used for modeling a flexible rod sliding inside a cylinder. The dynamic model of the system of six closed loop mechanisms was assembled using Hamilton’s principle and the Lagrange multiplier method. A linearized hydraulic control system based on rod length predictions was implemented independently to control the hydraulic cylinders. Consequently, the results of the simulations demonstrating the behavior of the robot machine are presented for each case study. In conclusion, this thesis studies the dynamic analysis of a special hybrid (serialparallel) robot for the above-mentioned special task involving the ITER and investigates different control algorithms that can significantly improve machining performance. These analyses and results provide valuable insight into the design and control of the parallel robot with flexible rods.