Caracterização microestrutural e elétrica de La(FexNi1-x)O3 sintetizado pelo método da gelatina

The present work deals with the synthesis of materials with perovskite structure with the intention of using them as cathodes in fuel cells SOFC type. The perovskite type materials were obtained by chemical synthesis method, using gelatin as the substituent of citric acid and ethylene glycol, and polymerizing acting as chelating agent. The materials were characterized by X-ray diffraction, thermal analysis, spectroscopy Fourier transform infrared, scanning electron microscopy with EDS, surface area determination by the BET method and Term Reduction Program, TPR. The compounds were also characterized by electrical conductivity for the purpose of observing the possible application of this material as a cathode for fuel cells, solid oxide SOFC. The method using gelatin and polymerizing chelating agent for the preparation of materials with the perovskite structure allows the synthesis of crystalline materials and homogeneous. The results demonstrate that the route adopted to obtain materials were effective. The distorted perovskite structure have obtained the type orthorhombic and rhombohedral; important for fuel cell cathodes. The presentation material properties required of a candidate cathode materials for fuel cells. XRD analysis contacted by the distortion of the structures of the synthesized materials. The analyzes show that the electrical conductivity obtained materials have the potential to act as a cell to the cathode of solid oxide fuel, allowing to infer an order of values for the electrical conductivities of perovskites where LaFeO3 < LaNiO3 < LaNi0,5Fe0,5O3. It can be concluded that the activity of these perovskites is due to the presence of structural defects generated that depend on the method of synthesis and the subsequent heat treatment

Desenvolvimento e caracterização de um compósito matriz metálica (CMM): aço EUROFER97 reforçado com Carbeto de Tântalo - TaC

Steel is an alloy EUROFER promising for use in nuclear reactors, or in applications where the material is subjected to temperatures up to 550 ° C due to their lower creep resistance under. One way to increase this property, so that the steel work at higher temperatures it is necessary to prevent sliding of its grain boundaries. Factors that influence this slip contours are the morphology of the grains, the angle and speed of the grain boundaries. This speed can be decreased in the presence of a dispersed phase in the material, provided it is fine and homogeneously distributed. In this context, this paper presents the development of a new material metal matrix composite (MMC) which has as starting materials as stainless steel EUROFER 97, and two different kinds of tantalum carbide - TaC, one with average crystallite sizes 13.78 nm synthesized in UFRN and another with 40.66 nm supplied by Aldrich. In order to improve the mechanical properties of metal matrix was added by powder metallurgy, nano-sized particles of the two types of TaC. This paper discusses the effect of dispersion of carbides in the microstructure of sintered parts. Pure steel powders with the addition of 3% TaC UFRN and 3% TaC commercial respectively, were ground in grinding times following: a) 5 hours in the planetary mill for all post b) 8 hours of grinding in the mill Planetary only for steel TaC powders of commercial and c) 24 hours in the conventional ball mill mixing the pure steel milled for 5 hours in the planetary mill with 3% TaC commercial. Each of the resulting particulate samples were cold compacted under a uniaxial pressure of 600MPa, on a cylindrical matrix of 5 mm diameter. Subsequently, the compressed were sintered in a vacuum furnace at temperatures of 1150 to 1250 ° C with an increment of 20 ° C and 10 ° C per minute and maintained at these isotherms for 30, 60 and 120 minutes and cooled to room temperature. The distribution, size and dispersion of steel and composite particles were determined by x-ray diffraction, scanning electron microscopy followed by chemical analysis (EDS). The structures of the sintered bodies were observed by optical microscopy and scanning electron accompanied by EDS beyond the x-ray diffraction. Initial studies sintering the obtained steel EUROFER 97 a positive reply in relation to improvement of the mechanical properties independent of the processing, because it is obtained with sintered microhardness values close to and even greater than 100% of the value obtained for the HV 333.2 pure steel as received in the form of a bar

Infravermelho na caracterização de ácidos húmicos de latossolo sob efeito de uso contínuo de lodo de esgoto.

Objetivou-se caracterizar, por meio de espectroscopia no infravermelho com transformada de Fourier (IVTF), possíveis mudanças na natureza química de ácidos húmicos (AHs) extraídos de amostras de Latossolo (0?10 cm) do Campo Experimental da Embrapa Meio Ambiente, em Jaguariúna (SP). Os dados foram obtidos após seis cultivos de milho e a aplicação de doses variáveis de lodo de esgoto de Barueri (LB) (base seca), conforme os tratamentos avaliados: LB0, LB1, LB2, LB4 e LB8 sendo 0, 1, 2, 4 e 8 vezes a necessidade de N para o milho, correspondendo a 0, 30, 60, 120 e 240 t ha-1. Como referência, foi amostrada uma área sob mata. Foram obtidos espectros de ácidos húmicos e do lodo de esgoto utilizado no experimento, e calculados os índices de hidrofobicidade (IH) e de condensação (IC) nas amostras de ácidos húmicos. Foram notadas pequenas alterações na natureza química de AHs de áreas tratadas com lodo de esgoto, em relação à testemunha. Os AHs apresentam grupos aromáticos, -OH fenólicos, - COOH, estruturas alifáticas, carboidratos e impurezas minerais. O uso contínuo de elevadas doses de LB reduziu a concentração de C-alifático e o grau de condensação dos ácidos húmicos, o que sinaliza que há frações orgânicas com maior biodisponibilidade no solo. Na área de mata, o material húmico se caracteriza pelo caráter hidrofóbico e pelo baixo grau de condensação.

Estratégias para intervenções de reparação e reforço em estruturas de betão armado

Já se passaram algumas décadas desde que o betão é o principal material de construção que ergue cidades e estruturas nas civilizações contemporâneas. Num passado não muito longínquo, a área da durabilidade, manutenção e prevenção das estruturas de betão não foi vista como prioridade, chegando a ser negligenciada, por consequência hoje existem graves problemas nalgumas construções de betão. Por outro lado, devido ao excedente de construção habitacional em Portugal e à, a atual conjuntura económica/financeira que a Europa atravessa, o setor da construção tem sofrido um abrandamento acentuado. A consciência e postura de sustentabilidade das novas gerações e entidades competentes, acentuou a necessidade de preservar, reparar e reforçar muito do património no parque habitacional português e europeu. O projeto de intervenção numa estrutura nunca é abordada da mesma maneira, não existem duas estruturas iguais, e há particularidades neste tipo de projetos que não existem num projeto de uma estrutura nova. Para intervir numa estrutura já construída é necessário um conhecimento abrangente em várias temáticas, tais como: regulamentação, métodos de avaliação de segurança, definição das características mecânicas dos materiais, técnicas de reparação e reforço, metodologias de diagnostico e intervenção, comportamento estrutural, etc. Atualmente existe muita informação acerca da temática de reparação e reforço de estruturas de betão armado, no entanto há ainda alguma falta de documentação onde a informação aparece de forma integral e objetiva. Consideando o apresentado anteriormente, tentou-se compilar informação sobre os principais assuntos que interessam a um projeto de reparação/reforço de estruturas de betão armado, nomeadamente as normas e legislação aplicável, exemplos de metodologias de inspeção e intervenção, os principais ensaios em laboratório e in situ para caracterização dos materiais, principais técnicas de reparação/reforço. Sobre este tópico e a título de exemplo, aprofundou-se com mais detalhe as considerações relativas ao dimensionamento com reforço com FRP´s.

Caracterização batimétrica e fisicooceanográfica do canal de acesso ao porto de Cabedelo/PB: uma análise ambiental ao derrame de óleo

The State of Paraíba is one of the most dynamic states of Brazil, strategically located in the northeast, is notable for the excellent potential for integration of different transportation modes forming the states of Rio Grande do Norte, Pernambuco and Alagoas. The dynamic that occurs with port activity causes changes in the space where it is installed. And the elements of this space are always more than suffering direct or indirect influences as the flow in the port is expanded. Therefore, this region became subject to the accidental spillage of oil, because it presents a heavy traffic of ships of various sizes that can run aground or collide with oil causing accidental events. The study of geomorphological and sedimentological compositions of seafloor becomes important as more is known about the relationships between these parameters and associated fauna, and can identify their preferred habitats. The database background, acoustically collected along the proposed study area, is a wealth of information, which were duly examined, cataloged and made available. Such information can serve as an important tool, providing a geomorphological survey of the sedimentary area studied, and come to subsidize, in a flexible, future decision making. With the study area Port of Cabedelo, Paraíba - Brazil, this research aimed to evaluate the influence of the tidal surface and background in modeling the seabed, including the acquisition of information about the location of submerged rocky bodies and the depth of these bodies may turn out to be natural traps for the trapping of oil in case of leaks, and obtain the relationship between types of bed and the hydrodynamic conditions present in the region. In this context, for this study were collected bathymetric data (depth) and physical oceanographic (height of water column, water temperature, intensity and direction of currents, waves and turbidity), meteorological (rainfall, air temperature, humidity, winds and barometric pressure) of the access channel to the Port of Cabedelo / PB and its basin evolution (where the cruise ships dock), and includes tools of remote sensing (Landsat 7 ETM +, 2001), so that images and the results are integrated into Geographic Information Systems and used in the elaboration of measures aimed at environmental protection areas under the influence of this scale facilities, serving as a grant to prepare a contingency plan in case of oil spills in the region. The main findings highlight the techniques of using hydroacoustic data acquisition together bathymetric surveys of high and low frequency. From there, five were prepared in bathymetric pattern of Directorate of Hydrography and Navigation - DHN, with the depth in meters, on a scale of 1:2500 (Channel and Basin Evolution of Access to Port of Cabedelo), where there is a large extent possible beachrocks that hinder the movement of vessels in the port area, which can cause collisions, running aground and leaking oil. From the scatter diagram of the vectors of currents, it can be seen as the tidal stream and undergoes a channeling effect caused by the bidirectional effect of the tide (ebb and flood) in the basin of the Port of Cabedelo evolution in NW-direction SE and the highest speed of the currents occurs at low tide. The characterization weather for the period from 28/02 to 04/07/2010 values was within the expected average for the region of study. The multidisciplinary integration of products (digital maps and remote sensing images), proved to be efficient for the characterization of underwater geomorphological study area, reaching the aim to discriminate and enhance submerged structures, previously not visible in the images

Caracterização reológica de pastas de cimento portland de alta resistência contendo diferentes tipos de polímeros superabsorventes pela técnica de reometria rotacional

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Civil e Ambiental, 2016.

Análise ao comportamento mecânico de estruturas de suporte produzidas por fdm

A produção aditiva tem vindo a ganhar cada vez mais importância no contexto atual pois, através destes processos, é possível criar protótipos de forma rápida que permitem de forma eficaz a visualização do modelo mas também, nalguns casos, a verificação da funcionalidade do mesmo. Este tipo de fabrico está em ascensão e estão constantemente a serem exploradas novas aplicações. Na produção aditiva, o material de suporte gerado para suportar a construção tem elevada importância no tempo e custo do processo. Neste contexto, torna-se cada vez mais evidente que é necessário entender o comportamento mecânico desta estrutura de modo a tornar o processo mais rápido e com menores custos sem comprometer a resistência das peças produzidas por este. O processo de FDM é um dos processos de produção aditiva que constrói modelos camada a camada a partir de ficheiros CAD que são tratados no software da máquina por forma a dividir o modelo em várias camadas finas que geram várias secções com as geometrias correspondentes. A construção do modelo físico é feita através da extrusão e deposição de polímeros consoante a secção pretendida. O principal objetivo deste trabalho é a caracterização mecânica do material de suporte gerado aquando a construção da peça final pretendida. Foi com este objetivo que foram criados modelos de teste através do processo de FDM para serem submetidos a ensaios de compressão de modo a entender de que forma o material de suporte influencia na resistência final do modelo. Da análise dos dados obtidos é possível concluir que o material de suporte não aumenta a resistência das peças produzidas.

Caracterização da cultura organizacional utilizando o Modelo dos Valores Contrastantes: o caso da Universidade de Évora

Considerada, cada vez mais, como um atributo organizacional essencial para o sucesso das organizações, a cultura organizacional ainda não é conhecida da maioria das Universidades, as quais têm sido sujeitas a transformações sem precedentes para se adaptar e a acompanhar os desafios societais. Adotando uma abordagem multimétodo, procurou-se a caracterizar a cultura organizacional de uma universidade publica portuguesa, segundo o Modelo dos Valores Contrastantes recorrendo ao questionário FOCUS e à entrevista semiestruturada de Quinn. Os resultados revelaram uma ênfase na cultura de regras para a Universidade no seu todo e de três subgrupos. A cultura de apoio foi enfatizada numa Escola. Estes resultados confirmam a tendência das entidades publicas valorizarem as regras, a estabilidade e os processos internos. A literatura afirma a necessidade de se procurarem estratégias de abertura ao exterior, flexibilizaçao de processos e estruturas deforma a aumentar a produtividade e melhorar a adaptação aos desafios externos; Abstract: Characterization of Organizational Culture using the Competing Values Framework: The Case of the University of Évora Regarded increasingly as an essential organizational attribute to the success of organizations, organizational culture is not known to most of the universities, which have been subject to unprecedented transformations to adapt and keep up with societal challenges. Adopting a multimethod approach, we sought to characterize the organizational culture of a public Portuguese university, according to the Competing Values Framework using the FOCUS questionnaire and semistructured interview by Quinn. The results revealed an emphasis on Rules culture for the University as a whole and three of their subgroups. The Support culture was emphasized in one university School. These results confirm the trend of public institutions to value the rules, stability and internal processes. The literature states that universities need to seek strategies opening to the outside, flexibilization of processes and structures to increase productivity and better adapt to external changes.

Caracterização do complexo de inclusão ropivacaína: beta-ciclodextrina

Characteriza of the inclusion complex ropivacaine: beta-cyclodextrin. Ropivacaine (RVC) is a widely used local anesthetic. The complexation of RVC with beta-cyclodextrin (beta-CD) is of great interest for the development of more efficient local anesthetic formulations. The present work focuses on the characterization of the RVC:beta-CD complex by nuclear magnetic resonance (NMR). The stoichiometry of the complex is 1:2 RVC:beta-CD. DOSY-NMR shows that the association constant is 55.5 M-1. Longitudinal relaxation time results show that RVC changes its mobility in the presence of beta-CD. This study is focused on the physicochemical characterization of inclusion complexes that are potentials options for pain treatment.

Desenvolvimento e caracterização de nanocápsulas de poli (L-lactídeo) contendo benzocaína

In this paper we describe the preparation poly (L-lactide) (PLA) nanocapsules as a drug delivery system for the local anesthetic benzocaine. The characterization and in vitro release properties of the system were investigated. The characterization results showed a polydispersity index of 0.14, an average diameter of 190.1± 3 nm, zeta potential of -38.5 mV and an entrapment efficiency of 73%. The release profile of Benzocaine loaded in PLA nanocapsules showed a significant different behavior than that of the pure anesthetic in solution. This study is important to characterize a drug release system using benzocaine for application in pain treatment.

Fracionamento de polifosfato de sódio e caracterização por RMN de 31P: um experimento para aulas de físico-química

This text describes an experiment on fractional precipitation of a polymer together with determination of average degree of polymerization by NMR. Commercial sodium polyphosphate was fractionated by precipitation from aqueous solution by adding increasing amounts of acetone. The polydisperse salt and nine fractions obtained from it were analyzed by 31P Nuclear Magnetic Resonance and the degree of polymerization of the salts and of the fractions were calculated. Long-chain sodium polyphosphate was also synthesized and analyzed. This experiment was tested in a PChem lab course but it can be used also to illustrate topics of inorganic polymers and analytical chemistry.

Caracterização físico-química de filmes comestíveis de amido adicionado de acerola (Malphigia emarginata D.C.)

Edibles films are an alternative to synthetic materials used for packing food products. Barbados cherry is rich in vitamin C and carotenoids. The aim of this study was to characterize and develop films by casting from cassava starch, lyophilized Barbados cherry pulp and glycerol. The films were characterized with respect to thickness, water vapor permeability (WVP), water solubility, vitamin C, carotene and mechanical properties. The interaction of pulp and glycerol reduced film thickness. An increase in pulp concentration up to 60% increased WVP but beyond this concentration reduced both WVP and solubility leading to an increased level of vitamin C and β carotene in the films.

Desenhos de estruturas químicas correlacionam-se com propriedades biológicas: MIA-QSAR

Descriptors in multivariate image analysis applied to quantitative structure-activity relationship (MIA-QSAR) are pixels of bidimensional images of chemical structures (drawings), which were used to model the trichomonicidal activities of a series of benzimidazole derivatives. The MIA-QSAR model showed good predictive ability, with r², q² and r val. ext.² of 0.853, 0.519 and 0.778, respectively, which are comparable to the best values obtained by CoMFA e CoMSIA for the same series. A MIA-based analysis was also performed by using images of alphabetic letters with the corresponding numeric ordering as dependent variables, but no correlation was found, supporting that MIA-QSAR is not arbitrary.

Desenvolvimento, produção e caracterização de nanocristais de fármacos pouco solúveis

Poorly soluble drugs have low bioavailability, representing a major challenge for the pharmaceutical industry. Processing drugs into the nanosized range changes their physical properties, and these are being used in pharmaceutics to develop innovative formulations known as Nanocrystals. Use of nanocrystals to overcome the problem of low bioavailability, and their production using different techniques such as microfluidization or high pressure homogenization, was reviewed in this paper. Examples of drugs, cosmetics and nutraceutical ingredients were also discussed. These technologies are well established in the pharmaceutical industry and are approved by the Food and Drug Administration.

Caracterização reológica das diferentes fases de extrato de inulina de raízes de chicória, obtidas por abaixamento de temperatura

Inulin is a functional food ingredient, generally employed as sugar or fat substitute in food systems. This ingredient can be found in several vegetal products, including chicory roots. As the solubility of inulin is susceptible to temperature changes, the product suffers a fractionalization resulting in two phases when cooled, originating a precipitated phase, more viscose, and a liquid phase, of lesser viscosity. The study of rheological properties of different phases of inulin extract is important for equipment designing, such as mixer and bombs. In this work, rheological behavior at three different temperatures (25; 40 and 50 ºC) was determined for liquid and precipitated phases of inulin liquid extract, extracted from chicory roots by hot water diffusion and cooled at two different temperatures (8 and -10 ºC), suffering phases separation. The precipitated phase was analyzed in two conditions: pure and with the addition of microencapsulating agents (maltodextrin and hydrolized starch). All of them presented a linear behavior, similar to that of the Plastics of Bingham. Some of them, however, were not an adequate fit to this model.