Sola romani: morteros hidráulicos romanos en la Península Ibérica

En esta investigación se han analizado morteros de cal de cronología romana en el interior de la Península Ibérica. Para ello, se seleccionó una serie de muestras procedentes de diversos yacimientos, y de estructuras de carácter industrial. Estas muestras presentan aditivos cerámicos y conglomerantes de cal, como característica principal. Desde un principio el esfuerzo debía de centrarse en los fragmentos cerámicos presentes en los morteros. Para ello se documentaron varios morteros con aditivos cerámicos, a fin de conocer sus características básicas (componentes, distribución, micro-estratigrafía, granulometría, etc.). Por ello, y una vez tomadas las muestras, ésta fueron tratadas y procesadas para desarrollar una primera fase de estudio por medio de macroscopía. Se obtuvieron buenos resultados en cuanto a la caracterización visual de los morteros, localizando y documentando los fragmentos cerámicos. Durante la observación de dichos aditivos se observó que los fragmentos cerámicos tenían unas coronas o anillos de coloración que recorrían el borde, justo al contacto con la matriz de cal. Fueron seleccionados algunos fragmentos en los que eran más visibles dichos anillos. A fin de conocer la posible relación entre algunos yacimientos cercanos y la presencia de dicho anillo cromáticos se desarrolló una microscopía óptica polarizada, realizando láminas delgadas de las muestras y sobre los fragmentos cerámicos más determinantes, en concreto de una serie de enclaves del valle del Henares. Además de caracterizar microscópicamente los morteros, se observó que los anillos no eran un defecto visual ni una alteración física, producida tal vez por la extracción, la fase del corte o por la cocción de la cerámica. Tras analizar varios ejemplares se pudo apreciar que esos anillos eran habituales en todas las muestras y que se presentaban de diferente manera, es decir, que se observaban en granos cerámicos de diferentes características físicas (cochura, tamaño, situación con respecto del conglomerante, etc.). A fin de conocer los aspectos químicos de dicha alteración se seleccionó un grupo de muestras en las que los resultados macroscópicos habían sido muy claros, y en las que la microscopía óptica polarizada había determinado en los bordes, áreas adecuadas para otros análisis. Se realizó un mapeado o mapping de elementos químicos, a fin de saber qué podía estar sucediendo en esa interfaz entre el fragmento cerámico y la matriz de cal. Gracias a los resultados obtenidos se comprobó que existía una acumulación potencial de calcio tanto en el interior de los granos cerámicos como en el exterior, justo en la zona de contacto con el conglomerante, formando manchas que recorrían longitudinalmente el borde. Estos datos fueron muy útiles para llevar a cabo la siguiente fase de estudio, que permitiría conocer puntualmente qué estaba sucediendo químicamente en esa zona de contacto. Finalmente y con el objetivo de describir química y puntualmente este efecto en las adiciones cerámicas, se volvió a seleccionar una serie de muestras, escogidas esta vez en función de los granos cerámicos que cumpliesen unas variables estadísticas. Se eligieron granos con distintos tipos de cocciones, así como granos con tamaños diversos y granos con aditivo ceniciento en la matriz de cal, pensando que podrían ser las variables más útiles de interpretar de existir algún tipo de cambio químico entre la arcilla cocida y la matriz de cal. Tales variables se adaptaron a un sistema estadístico multi-varial y geométrico, con el objetivo de sintetizar los resultados y visualizar de forma óptima los datos en conjunto, como se ha comentado en varias ocasiones en este trabajo. Una vez seleccionados los granos por variables se procedió a realizar un análisis lineal y espectral semi-cuantitativo de SEM-EDX, con el que se caracterizaba químicamente una sección lineal del grano, desde la matriz de arcilla cocida de la cerámica hasta la matriz de cal –del interior al exterior del grano- pasando por el centro de la banda de reacción. Este análisis permitió determinar que se había producido una serie de cambios químicos porcentuales en los granos de cerámica. Dichos cambios se resumen en un incremento global de los porcentajes de calcio en el interior de las bandas de reacción de la cerámica, desde el borde mismo del anillo hasta el exterior. Así también se observaron picos porcentuales en el interfaz del fragmento cerámico con la matriz de cal, lo que confirmaba los resultados obtenidos por medio del mapping. Globalmente en todas las muestras se apreció un hombro en las gráficas de calcio a su paso por la zona de afección del anillo de reacción. Los restantes porcentajes de magnesio, silicio y aluminio se mantienen normales. En esta tesis se ha confirmado que dicho incremento global de calcio se acentúa en las muestras en donde no hay cenizas en la matriz de cal. Los casos correspondientes a estos granos sufren un incremento mayor que en el resto. La segunda variable que sufre un mayor incremento de calcio es la que corresponde a granos con buena cocción de la arcilla. Por lo tanto, parece que la tercera variable, la que corresponde con el tamaño del fragmento cerámico, no es decisiva. Por lo tanto, teniendo en cuenta la prueba visual de los anillos de reacción, y atendiendo a los resultados químicos, podríamos pensar que ese incremento de calcio en la banda de reacción de los fragmentos cerámicos se debió a una absorción de calcio en el interior de la arcilla cocida en la fase inmediatamente previa al fraguado, incluso durante el apagado de la cal. Es en este punto donde estaría la clave del cambio químico que se produce en esta interfaz, el calcio sílice-aluminato del que algunos autores ya han investigado. Esta absorción de calcio en el interior del grano no vendría sola, sino que generaría una costra de cal en el interfaz exterior de la cerámica, la cual ha sido observada químicamente por mapping y mineralógicamente por medio de microscopía óptica de polarización. La consecuencia de estos resultados es, primero, la mejora de nuestro conocimiento general acerca del factor hidráulico en los morteros. Asimismo se aprecia que la incorporación de materiales orgánicos como cenizas, puede alterar los porcentajes de calcio en el interior de los aditivos cerámicos, por lo que habría que sopesar, en trabajos futuros, si este tipo de material es adecuado o no en las mezclas destinadas a la restauración, así como seguir indagando en las propiedades de los morteros con la incorporación de aditivos orgánicos. Desde el punto de vista de la catalogación de los suelos industriales hidráulicos de época romana, además de mejorar la documentación incorporando micro-estratigrafías y granulometrías, la investigación de este material histórico constructivo mejora en cuanto a que se incorporan ensayos sencillos, que facilitan incluso la peritación de un estado de conservación por medio de una lupa binocular. Arqueológicamente hablando, es muy interesante correlacionar fábricas diferentes de estructuras situadas o bien en un mismo yacimiento, o bien en una misma área regional. Los estudios de caracterización y micro-estratigrafía no sólo aportan datos nuevos de cara a la restauración de morteros, sino que crean la posibilidad de generar patrones constructivos que sirvan de fósiles-guía para datar relativamente a unas estructuras o a otras. En lo referido a los resultados obtenidos en los diferentes complejos arqueológicos se ha observado una diferencia entre los morteros destinados a piletas y cubetas con respecto a los suelos industriales de uso indeterminado. La muestra correspondiente al yacimiento de Las Arenas no dispone de ninguna micro-estratigrafía, como sí por el contrario en las muestras obtenidas en Rotonda de Mejorada, Val de la Viña y La Magdalena. En estos enclaves las estructuras presentan grandes similitudes, con diferentes niveles constructivos empleando morteros de cal con áridos y gravas en las capas interiores, y áridos con adiciones cerámicas en las exteriores. En lo relativo a la granulometría las adiciones cerámicas de las muestras de Val de la Viña y La Magdalena presentan varias coincidencias en cuanto al tamaño de los granos y la distribución. Asimismo, de las muestras tomadas en La Magdalena, existe una gran diferencia entre las muestras MG1, MG2, MG3 y MG4 con respecto a las muestras MG5 y MG6, correspondientes éstas últimas a un mortero con fragmentos cerámicos de gran tamaño. Las estructuras EMG1 y EMG2, correspondientes a una cubeta y una pileta de La Magdalena, guardan similitud en lo referido a la micro-estratigrafía y a la granulometría. Se ha determinado que su función, así como su fabricación, debieron estar vinculadas a un mismo contexto cronocultural. Química y mineralógicamente, las muestras presentan características iguales, con presencia de un conglomerante de cal con áridos y aditivos cerámicos de diferentes cochuras. Destaca la muestra de Las Arenas, con un tamaño de los fragmentos cerámicos muy superior al resto, seguido de la estructura EMG3 de La Magdalena. Las muestras restantes de éste enclave, junto con las muestras recogidas en Val de la Viña y Rotonda de Mejorada presentan condiciones similares. En conclusión, los datos revelan que existían diferentes fábricas destinadas a distintas finalidades, y que las estructuras industriales empleaban aditivos cerámicos para la manipulación de productos con líquidos, de distintas densidades pero que requerían de cierto grado de hidraulicidad. ABSTRACT Lime Roman mortars from the Iberian Peninsula has been analyzed in this reesearch. A group of samples were selected from some sites and all the samples come from industrial structures. All this samples show ceramic additives. From the start, the effort was centered in the pieces of pottery that were found in the mortars. The samples were treated and processed to develop a first phase of the research using macroscopy. With this technique, great results were achieved in the characterization of mortars, the microstratigraphy and the location of the ceramic pieces. While observing these pieces, it was seen that the fragments of pottery had a ring bordering the piece. The pieces with the bigger and more vivid rings were chosen and they were analyzed by a polarized light microscope. The mortars were characterized microscopically and it also showed that the rings were not a physical alteration or a visual defect. After some more tests, the rings were a chemical change associated with the hydraulicity of the mortar. The best samples were selected and mappings of their chemical elements were performed in order to know what could be happening in the interface between the ceramic matrix fragment and lime. With the results obtained it was found that there was a potential; both calcium accumulation within the ceramic grains and outside, just in the area of contact with the binder, forming spots longitudinally along the edge. These data were very useful for carrying out the next phase of study, which would meet promptly what was happening chemically in the area of contact. Another group of samples were taken, and this time focused on ceramic grains that met a statistical variables. Grains were chosen with two types of cooking as well as grains with different sizes and grains with ash additive in the matrix of lime, thinking that might be the most logical to be some sort of chemical change between the baked clay and lime array variables . Such variables were adapted to a multi-varial and geometric statistical system in order to synthesize the results and optimally display the data together, as mentioned several times in this work. After selecting the variables grains proceeded to perform a linear and spectral analysis SEM-EDX. This analysis led to determine that the chemical changes were graduals. These changes are summarized in an increase in the percentages of calcium inside the reaction rim of ceramics, from the edge to the outer ring. So percentage increasing is also observed at the interface of the ceramic matrix fragment with lime, confirming the results obtained by the mapping. Overall in all samples can be seen a shoulder in graphic calcium through the area of the ring reaction condition. The remaining percentages of magnesium, silicon and aluminum are usual. We have promptly confirmed that the increase of calcium is accentuated in samples where there is no ash and lime matrix. Cases for these grains suffer a greater increase than the rest. The second variable suffering more calcium is increased corresponding to good cooking grains with clay. Therefore, it appears that the variable size of the fragment is not critical. Therefore, considering the visual tests to the rings and their response to chemical results, we might think that increasing calcium inside the ceramic fragments was due to an injection of calcium inside clay in the run-up to the setting phase. It is at this point that would be the key to the chemical change that occurs at this interface, silica-calcium aluminate some authors have already investigated. This injection of calcium into the grain does not come alone, but generate a lime crust on the outside interface of ceramics, which we tested for mapping is real in our samples. The consequence of these results is the improvement of our understanding of historical hydraulic factor in building materials, such as mortar. For example, knowing that the incorporation of organic materials such as ash powder, may be detrimental to the injection of calcium inside the ceramic additives. Archaeologically speaking, it's very interesting to correlate different factories or structures located on a single site, or in the same regional area. Characterization studies and microstratigraphy not only provide new information to help restore mortars, but create the possibility of generating constructive patterns that serve as guide fossils to determinate the age of the structures. With regard to the results obtained in different archaeological sites it has seen a difference between mortars of pools or sinks with respect to industrial floors of undetermined use. The sample of the site of Las Arenas does not have any micro-stratigraphy, as if instead in the samples obtained in Rotonda de Mejorada, Val de la Viña and La Magdalena sites. In these settlements the structures are really similar, with different construction levels using lime mortars with aggregates and gravel in the inner layers, and ceramic aggregates as external additions. With regard to the grain size of the ceramic additions Val de la Viña and La Magdalena samples has several coincidences about the size of grains and distribution. Also, samples taken at La Magdalena, there is a difference between the MG1, MG2, MG3 and MG4 samples and the MG5 and MG6 samples, so the last corresponding to a mortar samples with larger ceramic fragments. The EMG1 and EMG2 structures, corresponding to a bucket and a pool of La Magdalena settlement, have similarities with regard to micro-stratigraphy and grain size. It has been determined that the function and manufacturing must be linked with a same chronocultural context.

A proposta (i)modesta de Berkeley. Um mundo sem matéria

Berkeley’s general tenet about immaterialism is presented and discussed. I examined apart the several theses that concur to the immaterialist theory. After that, the general argument is presented and discussed. In particular, I stress Berkeley’s assumption that a world without matter and a world with matter would be indistinguishable from the point of view of (i) the content of perceptions, (ii) natural science (viz. Newtonian mechanics). I stress that this assumption depends on a relative account of circular motion, generating the centrifugal forces, as Newton shows in his bucket experiment. In spite of the efforts by Leibniz and Huygens, such a relative account of rotational motion was never presented. So the thesis about the scientific and perceptual identity between worlds with and without matter remains a simple case of wishful thinking in need for a justification.

Investigation of planktic foraminifera from the Norwegian-Greenland Sea

The vertical density gradients in the Nordic Seas are crucial for the preconditioning of the surface water to thermohaline sinking in winter. These gradients can be reconstructed from paired oxygen isotope data in tests of different species of planktonic foraminifera, the isotopic signatures of which represent different calcification depths in the water column. Comparison of d18O values from foraminiferal tests in plankton hauls, sediment traps, and nearby core top samples with the calculated d18Ocalcite profile of the water column revealed species-specific d18O vital effects and the role of bioturbational admixture of subfossil specimens into the surface sediment. On the basis of core top samples obtained along a west-east transect across various hydrographic regions of the Nordic Seas, d18O values of Turborotalita quinqueloba document apparent calcification depths within the pycnocline at 25-75 m water depth. The isotopic signatures of Neogloboquadrina pachyderma (s) reflect water masses near and well below the pycnocline between 70 and 250 m off Norway, where the Atlantic inflow leads to thermal stratification. Here, temperatures in the calcification depth of N. pachyderma (s) differ from sea surface temperature by approximately -2.5°C. In contrast, N. pachyderma (s) calcifies very close to the sea surface (20-50 m) in the Arctic domain of the western Nordic Seas. However, further west N. pachyderma (s) prefers somewhat deeper, more saline water at 70-130 m well below the halocline that confines the low saline East Greenland Current. This implies that the d18O values of N. pachyderma (s) do not fully reflect the freshwater proportion in surface water and that any reconstruction of past meltwater plumes based on d18O is too conservative, because it overestimates sea surface salinity. Minimum d18O differences (<0.2per mil) between N. pachyderma (s) and T. quinqueloba may serve as proxy for sea regions with dominant haline and absent thermal stratification, whereas thermal stratification leads to d18O differences of >0.4 to >1.5per mil.

Marine ice-rafted debris records and age determinations along the northern Eurasian margin

Ice-rafted debris (IRD) (>2 mm), input in eight sediment cores along the Eurasian continental margin (Arctic Ocean), have been studied over the last two glacial/interglacial cycles. Together with the revised chronologies and new micropaleontological data of two cores from the northern Barents Sea (PS2138) and northeastern Kara Sea (PS2741) spanning Marine Isotope Stages (MIS) 6 to 1, the IRD data give new insights into the glacial history of northern Eurasian ice-sheets over the last 150 ka. The chronologies of the cores are based on stable isotope records, AMS 14C datings, paleomagnetic and biostratigraphic data. Extensive episodes of northern Barents Sea ice-sheet growth, probably to the shelf edge, occurred during the late Weichselian (MIS 2) and the Saalian (MIS 6). Major IRD discharge at the MIS 4/3-transition hints to another severe glaciation, probably onto the outer shelf, during MIS 4. IRD-based instabilities of the marine-based ice margin along the northern Barents Sea between MIS 4 and 2 are similar in timing with North Atlantic Heinrich events and Nordic Seas IRD events, suggesting similar atmospheric cooling over a broad region or linkage of ice-sheet fluctuations through small sea-level events. In the relatively low-precipitation areas of eastern Eurasia, IRD peak values during Termination II and MIS 4/3-transition suggest a Kara Sea ice-sheet advance onto the outer shelf, probably to the shelf edge, during glacial MIS 6 and 4. This suggests that during the initial cooling following the interglacials MIS 5, and possibly MIS 7, the combined effect of sustained inflow of Atlantic water into the Arctic Ocean and penetration of moisture-bearing cyclones into easterly direction supported major ice build-up during Saalian (MIS 6) and Mid-Weichselian (MIS 4) glaciation. IRD peak values in MIS 5 indicate at least two advances of the Severnaya Semlya ice-sheet to the coast line during the Early Weichselian. In contrast, a distinct Kara Sea ice advance during the Late Weichselian (MIS 2) is not documented by the IRD records along the northeastern Kara Sea margin.

Biomarker distributions in surface sediments from the Kara and Laptev Seas (Arctic Ocean)

Studies of spatial and temporal changes in modern and past sea-ice occurrence may help to understand the processes controlling the recent decrease in Arctic sea-ice cover. Here, we determined concentrations of IP25, a novel biomarker proxy for sea ice developed in recent years, phytoplankton-derived biomarkers (brassicasterol and dinosterol) and terrigenous biomarkers (campesterol and ß-sitosterol) in the surface sediments from the Kara and Laptev seas to estimate modern spatial (seasonal) sea-ice variability and organic-matter sources. C25-HBI dienes and trienes were determined as additional paleoenvironmental proxies in the study area. Furthermore, a combined phytoplankton-IP25 biomarker approach (PIP25 index) is used to reconstruct the modern sea-ice distribution more quantitatively. The terrigenous biomarkers reach maximum concentrations in the coastal zones and estuaries, reflecting the huge discharge by the major rivers Ob, Yenisei and Lena. Maxima in phytoplankton biomarkers indicating increased primary productivity were found in the seasonally ice-free central part of the Kara and Laptev seas. Neither IP25 nor PIP25, however, show a clear and simple correlation with satellite sea-ice distribution in our study area due to the complex environmental conditions in our study area and the transportation process of sea-ice diatom in the water column. Differences in the diene/IP25 and triene/IP25 ratios point to different sources of these HBIs and different environmental conditions. The diene/IP25 ratio seems to correlate positively with sea-surface temperature, while negatively with salinity distributions.

Statistical evaluation of the effectiveness of Federal Motor Vehicle Safety Standard 207: Seat Back Locks (Only). Final report.

National Highway Traffic Safety Administration, Washington, D.C.

A preliminary evaluation of seat back locks for two-door passenger cars with folding front seatbacks. Technical report.

Mode of access: Internet.

Melodies, duets, trios, songs, and ballads, pastoral, amatory, sentimental, patriotic, religious, and miscellaneous. Together with metrical epistles, tales and recitations.

Without music ; tunes indicated by title.

The complete coiffeur; or, An essay on the art of adorning natural, and of creating artificial, beauty ...

Both of the engraved titles have had the imprint erased, only the date 1817 being left intact.

Digital Activism: How Social Media Prevalence has Impacted Modern Activism

Thesis (Master's)--University of Washington, 2016-06

External perturbation of the trunk in standing humans differentially activates components of the medial back muscles

During voluntary arm movements, the medial back muscles are differentially active. It is not known whether differential activity also occurs when the trunk is perturbed unpredictably, when the earliest responses are initiated by short-latency spinal mechanisms rather than voluntary commands. To assess this, in unpredictable and self-initiated conditions, a weight was dropped into a bucket that was held by the standing subject (n = 7). EMG activity was recorded from the deep (Deep MF), superficial (Sup MF) and lateral (Lat MF) lumbar multifidus, the thoracic erector spinae (ES) and the biceps brachii. With unpredictable perturbations, EMG activity was first noted in the biceps brachii, then the thoracic ES, followed synchronously in the components of the multifidus. During self-initiated perturbations, background EMG in the Deep MF increased two- to threefold, and the latency of the loading response decreased in six out of the seven subjects. In Sup MF and Lat MF, this increase in background EMG was not observed, and the latency of the loading response was increased. Short-latency reflex mechanisms do not cause differential action of the medial back muscles when the trunk is loaded. However, during voluntary tasks the central nervous system exerts a 'tuned response', which involves discrete activity in the deep and superficial components of the medial lumbar muscles in a way that varies according to the biomechanical action of the muscle component.

Quality of Service System Approximation in IP Networks

This paper is sponsored by the Ministry of Education and Research of the Republic of Bulgaria in the framework of project No 105 “Multimedia Packet Switching Networks Planning with Quality of Service and Traffic Management”.