Coverage algorithms for an under-actuated car-like vehicle in an uncertain environment

A coverage algorithm is an algorithm that deploys a strategy as to how to cover all points in terms of a given area using some set of sensors. In the past decades a lot of research has gone into development of coverage algorithms. Initially, the focus was coverage of structured and semi-structured indoor areas, but with time and development of better sensors and introduction of GPS, the focus has turned to outdoor coverage. Due to the unstructured nature of an outdoor environment, covering an outdoor area with all its obstacles and simultaneously performing reliable localization is a difficult task. In this paper, two path planning algorithms suitable for solving outdoor coverage tasks are introduced. The algorithms take into account the kinematic constraints of an under-actuated car-like vehicle, minimize trajectory curvatures, and dynamically avoid detected obstacles in the vicinity, all in real-time. We demonstrate the performance of the coverage algorithm in the field by achieving 95% coverage using an autonomous tractor mower without the aid of any absolute localization system or constraints on the physical boundaries of the area.

Autonomous hot metal carrier

This paper reports work involved with the automation of a Hot Metal Carrier — a 20 tonne forklift-type vehicle used to move molten metal in aluminium smelters. To achieve efficient vehicle operation, issues of autonomous navigation and materials handling must be addressed. We present our complete system and experiments demontrating reliable operation. One of the most significant experiments was five-hours of continuous operation where the vehicle travelled over 8 km and conducted 60 load handling operations. We also describe an experiment where the vehicle and autonomous operation were supervised from the other side of the world via a satellite phone network.

Issues in autonomous navigation of underground vehicles

This paper describes current research at the Australian Centre for Field Robotics (ACFR) in collaboration with the Commonwealth Scientific and Industrial Research Organisation (CSIRO) within the Cooperative Research Centre (CRC) for Mining Technology and Equipment (CMTE) towards achieving autonomous navigation of underground vehicles, like a Load-Haul-Dump (LHD) truck. This work is being sponsored by the mining industry through the Australian Mineral Industries Research Association Limited (AMIRA). Robust and reliable autonomous navigation can only be realised by achieving high level tasks such as path-planning and obstacle avoidance. This requires determining the pose (position and orientation) of the vehicle at all times. A minimal infrastructure localisation algorithm that has been developed for this purpose is outlined and the corresponding results are presented. Further research issues that are under investigation are also outlined briefly.

Autonomous helicopter hover using an artificial neural network

Details the developments to date of an unmanned air vehicle (UAV) based on a standard size 60 model helicopter. The design goal is to have the helicopter achieve stable hover with the aid of an INS and stereo vision. The focus of the paper is on the development of an artificial neural network (ANN) that makes use of only the INS data to generate hover commands, which are used to directly manipulate the flight servos. Current results show that networks incorporating some form of recurrency (state history) offer little advantage over those without. At this stage, the ANN has partially maintained periods of hover even with misaligned sensors.

Obstacle detection for a mining vehicle using a 2D laser

This paper discusses a number of key issues for the development of robust obstacle detection systems for autonomous mining vehicles. Strategies for obstacle detection are described and an overview of the state-of-the-art in obstacle detection for outdoor autonomous vehicles using lasers is presented, with their applicability to the mining environment noted. The development of an obstacle detection system for a mining vehicle is then detailed. This system uses a 2D laser scanner as the prime sensor and combines dead-reckoning data with laser data to create local terrain maps. The slope of the terrain maps is then used to detect potential obstacles.

Issues in obstacle detection for autonomous mining and construction vehicles

This paper discusses a Dumber of key issues for the development of robust, obstacle detection systems for autonomous mining and construction vehicles. A taxonomy of obstacle detection systems is described; An overview of the state-of- the-art in obstacle detection for outdoor autonomous vehicles is presented with their applicability to the mining and construction environments noted. The issue of so-called fail-safe obstacle detection is then discussed. Finally, we describe the development of an obstacle detection system for a mining vehicle.

Design of a lightweight, modular robotic vehicle for the sustainable intensification of broadacre agriculture

This thesis presents the design process and the prototyping of a lightweight, modular robotic vehicle for the sustainable intensification of broadacre agriculture. Achieved by the joint operation of multiple autonomous vehicles to improve energy consumption, reduce labour, and increase efficiency in the application of inputs for the management of crops. The Small Robotic Farm Vehicle (SRFV) is a lightweight and energy efficient robotic vehicle with a configurable, modular design. It is capable of undertaking a range of agricultural tasks, including fertilising and weed management through mechanical intervention and precision spraying, whilst being more than an order of magnitude lower in weight than existing broadacre agricultural equipment.

Automatic Path Planning and Control Design for Autonomous Landing of UAVs using Dynamic Inversion

In this paper a nonlinear control has been designed using the dynamic inversion approach for automatic landing of unmanned aerial vehicles (UAVs), along with associated path planning. This is a difficult problem because of light weight of UAVs and strong coupling between longitudinal and lateral modes. The landing maneuver of the UAV is divided into approach, glideslope and flare. In the approach UAV aligns with the centerline of the runway by heading angle correction. In glideslope and flare the UAV follows straight line and exponential curves respectively in the pitch plane with no lateral deviations. The glideslope and flare path are scheduled as a function of approach distance from runway. The trajectory parameters are calculated such that the sink rate at touchdown remains within specified bounds. It is also ensured that the transition from the glideslope to flare path is smooth by ensuring C-1 continuity at the transition. In the outer loop, the roll rate command is generated by assuring a coordinated turn in the alignment segment and by assuring zero bank angle in the glideslope and flare segments. The pitch rate command is generated from the error in altitude to control the deviations from the landing trajectory. The yaw rate command is generated from the required heading correction. In the inner loop, the aileron, elevator and rudder deflections are computed together to track the required body rate commands. Moreover, it is also ensured that the forward velocity of the UAV at the touch down remains close to a desired value by manipulating the thrust of the vehicle. A nonlinear six-DOF model, which has been developed from extensive wind-tunnel testing, is used both for control design as well as to validate it.

Autonomous greenhouse gas sampling using multiple robotic boats

Accurately quantifying total greenhouse gas emissions (e.g. methane) from natural systems such as lakes, reservoirs and wetlands requires the spatial-temporal measurement of both diffusive and ebullitive (bubbling) emissions. Traditional, manual, measurement techniques provide only limited localised assessment of methane flux, often introducing significant errors when extrapolated to the whole-of-system. In this paper, we directly address these current sampling limitations and present a novel multiple robotic boat system configured to measure the spatiotemporal release of methane to atmosphere across inland waterways. The system, consisting of multiple networked Autonomous Surface Vehicles (ASVs) and capable of persistent operation, enables scientists to remotely evaluate the performance of sampling and modelling algorithms for real-world process quantification over extended periods of time. This paper provides an overview of the multi-robot sampling system including the vehicle and gas sampling unit design. Experimental results are shown demonstrating the system’s ability to autonomously navigate and implement an exploratory sampling algorithm to measure methane emissions on two inland reservoirs.

Evolving Philosophies on Autonomous Obstacle/Collision Avoidance of Unmanned Aerial Vehicles

Much of the benefits of deploying unmanned aerial vehicles can be derived from autonomous missions. For such missions, however, sense-and-avoid capability (i.e., the ability to detect potential collisions and avoid them) is a critical requirement. Collision avoidance can be broadly classified into global and local path-planning algorithms, both of which need to be addressed in a successful mission. Whereas global path planning (which is mainly done offline) broadly lays out a path that reaches the goal point, local collision-avoidance algorithms, which are usually fast, reactive, and carried out online, ensure safety of the vehicle from unexpected and unforeseen obstacles/collisions. Even though many techniques for both global and local collision avoidance have been proposed in the recent literature, there is a great interest around the globe to solve this important problem comprehensively and efficiently and such techniques are still evolving. This paper presents a brief overview of a few promising and evolving ideas on collision avoidance for unmanned aerial vehicles, with a preferential bias toward local collision avoidance.

Autonomous rigid body attitude synchronization

Control laws to synchronize attitudes in a swarm of fully actuated rigid bodies, in the absence of a common reference attitude or hierarchy in the swarm, are proposed in [Smith, T. R., Hanssmann, H., & Leonard, N.E. (2001). Orientation control of multiple underwater vehicles with symmetry-breaking potentials. In Proc. 40th IEEE conf. decision and control (pp. 4598-4603); Nair, S., Leonard, N. E. (2007). Stable synchronization of rigid body networks. Networks and Heterogeneous Media, 2(4), 595-624]. The present paper studies two separate extensions with the same energy shaping approach: (i) locally synchronizing the rigid bodies' attitudes, but without restricting their final motion and (ii) relaxing the communication topology from undirected, fixed and connected to directed, varying and uniformly connected. The specific strategies that must be developed for these extensions illustrate the limitations of attitude control with reduced information. © 2008 Elsevier Ltd.

自主/遥控水下机器人水面/水下通信协议设计与实现

为了解决自主/遥控水下机器人（ARV）水面控制台与水下载体之间的通信问题，设计并实现了一种基于分层结构的水面/水下通信协议。该协议根据ARV 通信特殊需求，分为应用层，数据链路层与物理层，各层之间通过事件路由的方式进行调用，层内协议规则通过有限状态机来描述，整个协议结构清晰。ARV 实验结果证明这一通信协议具有传输速率快，可靠性高等优点。

北极冰下自主/遥控机器人控制系统设计

针对北极冰下海洋参数监测的使命要求,对水下机器人控制系统进行了相关研究,将PC104总线与CAN总线应用到自主/遥控水下机器人中,实现了一种分布式与集中式相结合的水下机器人控制系统体系结构。从硬件和软件两个方面描述北极自主/遥控水下机器人控制系统的实施方案。

On the applications of a compact autonomous acoustic recorder

A number of acoustic A compact acoustic recorder, primarily designed for underwater noise monitoring, is presented in this paper. The Self-Register Hydrophone has been used in several occasions during the past three years, in underwater noise monitoring activities. However, this kind of device also find application in other areas such as array processing and passive acoustic monitoring of marine mammals. An overview on the application of the Self-Register Hydrophone is given herein.

An autonomous system for ocean acoustic tomography

Vertical line arrays (VLA) are a widely used apparatus in underwater acoustics with applications in sonar prediction, underwater communications and acoustic tomography, among others. Recent developments in digital electronics and communications allow for off-the-shelf development of VLA systems, with a large number of embedded acoustic and non-acoustic sensors able to fulfill application requirements, as opposed to single or few receiver configurations available until only a few years ago. Very often, the flexibility in water column sampling is achieved by splitting the VLA into modules that can be assembled according to the application. Such systems can be deployed and recovered from small vessels with a shorthanded crew, and make it possible for research labs with reduced budgets and operational means (ships and manpower) to gain control over the whole development process, from data acquisition to post-processing.