Variable-stiffness composite panels: Defect tolerance under in-plane tensile loading

Automated Fiber Placement is being extensively used in the production of major composite components for the aircraft industry. This technology enables the production of tow-steered panels, which have been proven to greatly improve the structural efficiency of composites by means of in-plane stiffness variation and load redistribution. However, traditional straight-fiber architectures are still preferred. One of the reasons behind this is related to the uncertainties, as a result of process-induced defects, in the mechanical performance of the laminates. This experimental work investigates the effect of the fiber angle discontinuities between different tow courses in a ply on the un-notched and open-hole tensile strength of the laminate. The influence of several manufacturing parameters are studied in detail. The results reveal that 'ply staggering' and '0% gap coverage' is an effective combination in reducing the influence of defects in these laminates

Simulation of Delamination Propagation in Composites Under High-Cycle Fatigue by Means of Cohesive-Zone Models

A damage model for the simulation of delamination propagation under high-cycle fatigue loading is proposed. The basis for the formulation is a cohesive law that links fracture and damage mechanics to establish the evolution of the damage variable in terms of the crack growth rate dA/dN. The damage state is obtained as a function of the loading conditions as well as the experimentally-determined coefficients of the Paris Law crack propagation rates for the material. It is shown that by using the constitutive fatigue damage model in a structural analysis, experimental results can be reproduced without the need of additional model-specific curve-fitting parameters

Bridgeless interleaved boost PFC converter with variable duty cycle control

This paper proposes a bridgeless boost interleaved PFC (power factor correction) converter with variable duty cycle control. The application of bridgeless technique causes reduction of conduction losses, while the interleaving technique of converters cells allows division of efforts in semiconductor devices and reduction of weight and volume of the input EMI filter. The use of variable duty cycle control has the functions of regulating the output voltage and eliminating the low order harmonic components that appears in the input current of the common interleaved power factor converters working in Discontinuous Conduction Mode (DCM). The simulation results of the proposed converter presented high power factor and a good transient response in relation to the output voltage regulation in presence of high load variations and supply voltage variations. © 2011 IEEE.

Comparison of variable-thread tapered implant designs to a standard tapered implant design after immediate loading. A 3-year multicentre randomised controlled trial

This randomised, controlled multicentre trial aimed at comparing two versions of a variable-thread dental implant design to a standard tapered dental implant design in cases of immediate functional loading for 36 months after loading.

Numerical Model of a Variable-Combined-Cycle Engine for Dual Subsonic and Supersonic Cruise

Efficient high speed propulsion requires exploiting the cooling capability of the cryogenic fuel in the propulsion cycle. This paper presents the numerical model of a combined cycle engine while in air turbo-rocket configuration. Specific models of the various heat exchanger modules and the turbomachinery elements were developed to represent the physical behavior at off-design operation. The dynamic nature of the model allows the introduction of the engine control logic that limits the operation of certain subcomponents and extends the overall engine operational envelope. The specific impulse and uninstalled thrust are detailed while flying a determined trajectory between Mach 2.5 and 5 for varying throttling levels throughout the operational envelope.

Computer vision in aseptic pharmaceutical manufacturing: a deep learning-based approach to vial inspection and pack formation during a lyophilizer loading cycle

Vision systems are powerful tools playing an increasingly important role in modern industry, to detect errors and maintain product standards. With the enlarged availability of affordable industrial cameras, computer vision algorithms have been increasingly applied in industrial manufacturing processes monitoring. Until a few years ago, industrial computer vision applications relied only on ad-hoc algorithms designed for the specific object and acquisition setup being monitored, with a strong focus on co-designing the acquisition and processing pipeline. Deep learning has overcome these limits providing greater flexibility and faster re-configuration. In this work, the process to be inspected consists in vials’ pack formation entering a freeze-dryer, which is a common scenario in pharmaceutical active ingredient packaging lines. To ensure that the machine produces proper packs, a vision system is installed at the entrance of the freeze-dryer to detect eventual anomalies with execution times compatible with the production specifications. Other constraints come from sterility and safety standards required in pharmaceutical manufacturing. This work presents an overview about the production line, with particular focus on the vision system designed, and about all trials conducted to obtain the final performance. Transfer learning, alleviating the requirement for a large number of training data, combined with data augmentation methods, consisting in the generation of synthetic images, were used to effectively increase the performances while reducing the cost of data acquisition and annotation. The proposed vision algorithm is composed by two main subtasks, designed respectively to vials counting and discrepancy detection. The first one was trained on more than 23k vials (about 300 images) and tested on 5k more (about 75 images), whereas 60 training images and 52 testing images were used for the second one.

Effects of temperature at different organic loading levels on the performance of a fluidized-bed anaerobic sequencing batch bioreactor

An investigation was performed on the effect of temperature and organic load on the stability and efficiency of a 1.8-L fluidized-bed anaerobic sequencing batch reactor (ASBR), containing granulated biomass. Assays were carried out employing superficial up How velocity of 7 m/h, total cycle length of 6 h and synthetic wastewater volume of 1.3 L per cycle. The fluidized-bed ASH was operated at 15, 20, 25 and 30 degrees C with influent organic matter concentrations of 500 and 1000 mgCOD/L The system showed stability under all conditions and presented filtered samples removal efficiency ranging from 79 to 86%. A first-order kinetic model could be fitted to the experimental values of the organic matter concentration profiles. The specific kinetic parameter values of this model ranged from 0.0435 to 0.2360 L/(gTVS h) at the implemented operation conditions. in addition, from the slope of an Arrhenius plot, the activation energy values were calculated to be 16,729 and 12,673 cal/mol for operation with 500 and 1000 mgCOD/L, respectively. These results show that treatment of synthetic wastewater. with concentration of 500 mgCOD/L, was more sensitive to temperature variations than treatment of the same residue with concentration of 1000 mgCOD/L. Comparing the activation energy value for operation at 500 mgCOD/L with the value obtained by Agibert et al. (S.A. Agibert, M.B. Moreira, S.M. Ratusznei, J.A.D. Rodrigues, M. Zaiat, E. Foresti. Influence of temperature on performance of an ASBBR with circulation applied to treatment of low-strength wastewater. journal of Applied Biochemistry and Biotechnology, 136 (2007) 193-206) in an ASBBR treating the same wastewater at the same concentration, the value obtained in the fluidized-bed ASBR showed to be superior, indicating that treatment of synthetic wastewater in a reactor containing granulated biomass was more sensitive to temperature variations than the treatment using immobilized biomass. (c) 2008 Elsevier B.V. All rights reserved.

Anaerobic sequencing batch biofilm reactor applied to automobile industry wastewater treatment: Volumetric loading rate and feed strategy effects

This paper presents a technological viability study of wastewater treatment in an automobile industry by an anaerobic sequencing batch biofilm reactor containing immobilized biomass (AnSBBR) with a draft tube. The reactor was operated in 8-h cycles, with agitation of 400 rpm, at 30 degrees C and treating 2.0 L wastewater per cycle. Initially the efficiency and stability of the reactor were studied when supplied with nutrients and alkalinity. Removal efficiency of 88% was obtained at volumetric loading rate (VLR) of 3.09 mg COD/L day. When VLR was increased to 6.19 mg COD/L day the system presented stable operation with reduction in efficiency of 71%. In a second stage the AnSBBR was operated treating wastewater in natura, i.e., without nutrients supplementation, only with alkalinity, thereby changing feed strategy. The first strategy consisted in feeding 2.0 L batch wise (10 min), the second in feeding 1.0 L of influent batch wise (10 min) and an additional 1.0 L fed-batch wise (4 h), both dewatering 2.0 L of the effluent in 10 min. The third one maintained 1.0 L of treated effluent in the reactor, without discharging, and 1.0 L of influent was fed fed-batch wise (4 h) with dewatering 1.0 L of the effluent in 10 min. For all implemented strategies (VLR of 1.40, 2.57 and 2.61 mg COD/L day) the system presented stability and removal efficiency of approximately 80%. These results show that the AnSBBR presents operational flexibility, as the influent can be fed according to industry availability. In industrial processes this is a considerable advantage, as the influent may be prone to variations. Moreover, for all the investigated conditions the kinetic parameters were obtained from fitting a first-order model to the profiles of organic matter, total volatile acids and methane concentrations. Analysis of the kinetic parameters showed that the best strategy is feeding 1.0 L of influent batchwise (10 min) and 1.0 L fed-batch wise (4 h) in 8-h cycle. (c) 2007 Elsevier B.V. All rights reserved.

Test procedure for variable rate fertilizer on coffee

The objective was to develop and test a procedure for applying variable rates of fertilizers and evaluate yield response in coffee (Coffea arabica L.) with regard to the application of phosphorus and potassium. The work was conducted during the 2004 season in a 6.4 ha field located in central Sao Paulo state. Two treatments were applied with alternating strips of fixed and variable rates during the whole season: one following the fertilizing procedures recommended locally, and the other based on a grid soil sampling. A prototype pneumatic fertilizer applicator was used, carrying two conveyor belts, one for each row. Harvesting was done with a commercial harvester equipped with a customized volumetric yield monitor, separating the two treatments. Data were analyzed based on geostatistics, correlations and regressions. The procedure showed to be feasible and effective. The area that received fertilizer applications at a variable rate showed a 34% yield increase compared to the area that received a fixed rate. The variable rate fertilizer resulted in a savings of 23% in phosphate fertilizer and a 13% increase in potassium fertilizer, when compared to fixed rate fertilizer. Yield in 2005, the year after the variable rate treatments, still presented residual effect from treatments carried out during the previous cycle.

The effects of viscous loading of the human forearm flexors on the stability of coordination

This experiment investigated whether the stability of rhythmic unimanual movements is primarily a function of perceptual/spatial orientation or neuro-mechanical in nature. Eight participants performed rhythmic flexion and extension movements of the left wrist for 30 s at a frequency of 2.25 Hz paced by an auditory metronome. Each participant performed 8 flex-on-the-beat trials and 8 extend-on-the-beat trials in one of two load conditions, loaded and unload. In the loaded condition, a servo-controlled torque motor was used to apply a small viscous load that resisted the flexion phase of the movement only. Both the amplitude and frequency of the movement generated in the loaded and unloaded conditions were statistically equivalent. However, in the loaded condition movements in which participants were required to flex-on-the-beat became less stable (more variable) while extend-on-the-beat movements remained unchanged compared with the unload condition. The small alteration in required muscle force was sufficient to result in reliable changes in movement stability even a situation where the movement kinematics were identical. These findings support the notion that muscular constraints, independent of spatial dependencies, can be sufficiently strong to reliably influence coordination in a simple unimanual task.

Mechanical loading modulates glutamate receptor subunit expression in bone

The cellular mechanisms coupling mechanical loading with bone remodeling remain unclear. In the CNS, the excitatory amino acid glutamate (Glu) serves as a potent neurotransmitter exerting its effects via various membrane Glu receptors (GluR). Nerves containing Glu exist close to bone cells expressing functional GluRs. Demonstration of a mechanically sensitive glutamate/aspartate transporter protein and the ability of glutamate to stimulate bone resorption in vitro suggest a role for glutamate linking mechanical load and bone remodeling. We used immunohistochemical techniques to identify the expression of N-methyl-D-aspartate acid (NMDA) and non-NMDA (AMPA or kainate) ionotropic GluR subunits on bone cells in vivo. In bone sections from young adult rats, osteoclasts expressed numerous GluR subunits including AMPA (GluR2/3 and GluR4), kainic acid (GluR567) and NMDA (NMDAR2A, NMDAR2B and NMDAR2C) receptor subtypes. Bone lining cells demonstrated immunoexpression for NMDAR2A, NMDAR2B, NMDAR2C, GluR567, GluR23, GuR2 and GluR4 subunits. Immunoexpression was not evident on osteocytes, chondrocytes or vascular channels. To investigate the effects of mechanical loading on GluR expression, we used a Materials Testing System (MTS) to apply 10 N sinusoidal axial compressive loads percutaneously to the right limbs (radius/ulna, tibia/fibula) of rats. Each limb underwent 300-load cycles/day (cycle rate, 1 Hz) for 4 consecutive days. Contralateral, non-loaded limbs served as controls. Mechanically loaded limbs revealed a load-induced loss of immunoexpression for GluR2/3, GluR4, GluR567 and NMDAR2A on osteoclasts and NMDAR2A, NMDAR2B, GluR2/3 and GluR4 on bone lining cells. Both neonatal rabbit and rat osteoclasts were cultured on bone slices to investigate the effect of the NMDA receptor antagonist, MK801, and the AMPA/kainic acid receptor antagonist, NBQX, on osteoclast resorptive activity in vitro. The inhibition of resorptive function seen suggested that both NMDAR and kainic acid receptor function are required for normal osteoclast function. While the exact role of ionotropic GluRs in skeletal tissue remains unclear, the modulation of GluR subunit expression by mechanical loading lends further support for participation of Glu as a mechanical loading effector. These ionotropic receptors appear to be functionally relevant to normal osteoclast resorptive activity. (C) 2005 Elsevier Inc. All rights reserved.

Cell cycle and apoptosis in normal and cloned bovine near-term placentae

The bovine maternal epithelium is composed of cuboidal cells interspersed with low columnar cells having centrally located nuclei. Bovine trophoblast is composed of two cell types: mononuclear trophoblastic and giant trophoblastic cells that can have two or more nuclei. Number of apoptotic cells and proliferative cells are variable in both cell populations. This study compared tissue growth and apoptosis by flow cytometry in the cell population found at distinct placental regions (central region of placentomes, <= 1-cm microplacentomes and the interplacentomal region) between normal and cloned near-term bovine pregnancies. After a morphological comparison between regions and groups (controls vs. clones), a lesser proportion of diploid to tetraploid cells was observed in the central region of placentomes and in microplacentomes from cloned-derived pregnancies. In addition, cloned animals had a fewer apoptotic cells in the central region of the placentome and in interplacentomal region and a greater proliferative capacity in all regions (cells in G(2)/M) near term as opposed to control animals. These results may reveal the existence of a relationship between such changes in the proportions of uterine and trophoblastic epithelial cells at the end of pregnancy and normal placental function. This could be related to faulty placentation in early pregnancy, placental insufficiency during pregnancy or lack of placental and/or fetal maturation in late pregnancy, which may contribute to someof the abnormalities after in vitro embryo manipulations, such as poor preparation and initiation of parturition, prolonged gestation and lesser post-natal survival in some cloned animals. (C) 2008 Elsevier B.V. All rights reserved.

Life-cycle performance of structures: combining expert judgment and results of inspection

Life-Cycle Civil Engineering – Biondini & Frangopol

Credit cycle identification: A Markov-switching application

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Finance from the NOVA – School of Business and Economics

Ciclos económicos en economías abiertas y menos desarrolladas: el papel de los "shocks" en los términos de intercambio.The business cycle in open and less developed economies: the rol of terms-of-trade shocks.

Nuestra preocupación reside en estudiar empíricamente el mecanismo de transmisión internacional de ciclos económicos a economías pequeñas y menos desarrolladas (LDC), evaluando el impacto de los shocks en los términos de intercambio en países dónde existen imperfecciones en el mercado crediticio que imponen severas restricciones en el financiamiento de la inversión doméstica y al crecimiento económico. Primero, analizamos si la cuenta corriente responde de manera asimétrica a movimientos de largo plazo en los términos de intercambio. La hipótesis es que “en los buenos tiempos” cuando se produce una mejora permanente en términos de intercambio (y con ello el nivel de ingreso) los individuos no elevan su consumo en un monto acorde con la mejora de su ingreso (permanente) sino que ahorran una fracción del aumento en su dotación para hacer frente a una reversión en la mejora en los términos de intercambios (aunque ésta sea transitoria) en el futuro. En consecuencia, la cuenta corriente (diferencia entre ingreso y absorción) responde de manera positiva a un shock permanente en los términos de intercambio, ya que el individuo ahorra de manera cautelosa –debido a que sabe que no le prestarán para suavizar consumo - aún suponiendo que en el futuro tendrá una reversión transitoria de su ingreso. Segundo, estudiamos la relación dinámica entre los términos de intercambio y la tasa de interés en la economía pequeña abierta y con imperfecciones en el mercado crediticio (información asimétrica). La hipótesis es que la economía doméstica tiene que soportar una prima de riesgo que eleva el costo de la inversión y retarda el crecimiento (Gertler y Rogoff; 1990). Esta prima de riesgo depende, además, en forma negativa del nivel del colateral que tenga la economía. El colateral es la dotación de recursos naturales, por ejemplo, que la economía posee a los fines garantizar el cumplimiento de las obligaciones contraídas (en el modelo presentado las actividades dónde se invierten son independientes del colateral). La hipótesis establecida indica que los cambios en los términos de intercambio generan un aumento del colateral de la economía y una reducción del riesgo país: aumentos en los términos de intercambio reducen la prima de riesgo de la economía que opera en mercados de capitales con asimetrías de información, y como consecuencia aumentarían los ingresos de capitales. De esta forma, se estaría encontrando una explicación a la denominada “Paradoja de Lucas”. Finalmente, el proyecto estudia la conexión entre dos variables “clave” en la economía de los países emergentes: la relación entre los términos de intercambio y el tipo de cambio real. Argumentamos que los efectos de las mejoras de los términos de intercambio sobre los flujos de capitales externos tienden a ser sobreestimadas si no se consideran los efectos “secundarios” de éstas sobre el tipo de cambio real de la economía pequeña menos desarrollada. En este proyecto se controlan estadísticamente esta relación. La estrategia empírica elegida resulta en aplicar a un panel (constituido por dieciocho países de Latinoamérica) el método generalizado de momentos (GMM) a dos modelos de regresión estadística a los fines de abordar de manera eficiente el problema de la endogeneidad de la variable dependiente que actúa como regresor rezagado. La estrategia de estimación elegida enfatiza el análisis de la relación dinámica de las variables económicas incluidas en el análisis. The paper analyzes the general problem related to the transmission of economic cycles to Small Open Economies. The analysis focuses on terms-of-trade shocks, which are considered one of the major sources of income volatility in developing economies. Specifically, we tackle the problem related to the impact of terms-of-trade shocks in Less Developed SOEs. ‘Less Developed SOEs’ are understood as those countries who have borrowing constraints. First, we put to a test the hypothesis of asymmetric response of current account to terms-of-trade shocks (the impact of the shock on current account differs depending whether it is positive or negative), which originates from considering binding restrictions in international capital markets (Agénor and Aizenman; 2004). Second, we investigate about the main determinants of External Capital Flows (ECF) directed to Developing Countries. We put to a test the Gertler and Rogoff (1990) hypothesis that a “risky rate” arises in that markets because the economy has not sufficient amount of wealth to “collateralize” the capital she needs to borrow to take advantage of the investment opportunities she has and additionally because the lender does not have the chance of observing what the borrowed does with the funds (that is information asymmetry arises because the lender can check the realized output of investment but he can not observe if he really invest in the project or secretly lend abroad). Finally, Following Prasad, E. S., Rajan and R. Subramanian, A (2007) we measure the relationship between external capital flows and domestic currency overvaluation. We run a panel GMM estimation for a set of 18 Latin American Countries during the period 1973-2008.