脉冲激光离散重熔热物理及组织性能研究

利用OM及FEM研究了铁基合金Nd:YAG脉冲激光熔凝区的几何形态及其变化规律、以及熔凝的热物理过程；利用OM、SEM、TEM、X-射线衍射仪及磨损实验机，研究了两种铁基热模具材料脉冲激光熔凝组织及其时效组织结构，以及熔凝区规则离散分布规律对材料抗磨损性能的影响。在10~5～10~7W/cm~2的脉冲激光平均功率密度范围内，可得到热传导型和深熔型两类强化区，当临界平均功率密度大于5 * 10~5W/cm~2，同时临界激光作用时间大于2ms时，热传导型强休区向深熔型强休区转变。熔化过程中，在熔池中形成上部以对流传热为主，底部以导热为主的传热模式，流场、温度场和压力场均随脉冲激光作用时间变化，最大流速、压力和温度梯度分别可达100m/s、数个大气压和10~(8-9) ℃C/m量级。凝固过程中，固液界面上的最大温度梯度、凝固速率和冷却速度时间和空间位置变化，分别可达10~(8-9) ℃/m量级、10~(-1)m/s量级和10~(7-8) ℃/s量级，其中冷却速度得到实验验证。亚共晶合金铸铁脉冲激光熔凝组织为δ-铁素体与M_3C的层片状共晶组织，还含有部分γ-奥氏体和少量的高碳孪晶马氏体组织，δ-铁素体和γ-奥氏体中均存在高密度位错亚结构。5CrMnMo钢脉冲激光熔凝组织由板条马氏体及少量的孪晶马氏体构成，马氏体中也存在高密度位错亚结构。上述两种组织经高温时效后，仍保持较细的晶粒，并有大量细小均匀弥散分布的碳化物析出，其中铸铁熔凝组织析出M_(23)C_6碳化物，M_(23)C_6可在M_3C/γ-奥氏体相界面或M_3C内部原位形核，亦可在δ-铁素体中弥散析出。两种材料的熔凝组织及其时效组织的显微硬度均明显高于相应的原始组织，也高于激光连续扫描熔凝的结果。脉冲激光规则离散熔凝加工在材料表面形成软硬相间的“原位”功能层，能显著降低裂纹形成的敏感性，提高材料表层的抗磨粒磨损性能，时效后仍具有较好的抗磨损性能。以熔凝强化区直径作为中心间距进行规则离散熔凝处理可使材料表面获得最佳抗磨损性能。

Heat Transfer of Aviation Kerosene at Supercritical Conditions

The heat transfer characteristics of China no. 3 kerosene were investigated experimentally and analytically under conditions relevant to a regenerative cooling system for scramjet applications. A test facility developed for the present study can handle kerosene in a temperature range of 300-1000 K, a pressure range of 2.6-5 MPa, and a mass How rate range of 10-100 g/s. In addition, the test section was uniquely designed such that both the wall temperature and the bulk fuel temperature were measured at the same location along the flowpath. The measured temperature distributions were then used to analytically deduce the local heat transfer characteristics. A 10-component kerosene surrogate was proposed and employed to calculate the fuel thermodynamic and transport properties that were required in the heat transfer analysis. Results revealed drastic changes in the fuel flow properties and heat transfer characteristics when kerosene approached its critical state. Convective heat transfer enhancement was also found as kerosene became supercritical. The heat transfer correlation in the relatively low-fuel-temperature region yielded a similar result to other commonly used jet fuels, such as JP-7 and JP-8, at compressed liquid states. In the high-fuel-temperature region, near and beyond the critical temperature, heat transfer enhancement was observed; hence, the associated correlation showed a more significant Reynolds number dependency.

Calculations and predications of combustion oscillations

The combustion oscillations are the phenomena which we may meet in developing the clean, safe and efficient power and propulsion systems. This paper summarizes authors' systematic work on fuel spray combustion oscillations in the recent years. Combining CFD calculations and stability analysis, a new approach of predicting combustion stabilities was developed. With this approach, detailed flow information and unstable modes can be obtained by CFD and solving perturbation equations, respectively. The results provide the guidance on understanding combustion instability mechanisms and developing the control strategies.

Challenges for turbomachinery CFD in the 21st century

This lecture aims to identify a range of problems in turbomachinery which deserve attention. There is a discussion of what current levels of CFD can offer towards solving these problems. Finally, fruitful areas of future CFD research are described and current progress in these areas is summarised.

Unsteady Simulations of a Film Cooling Flow from an Inclined Cylindrical Jet

Film cooling is extensively used to provide protection against the severe thermal environment in gas turbine engines. Most of the computational studies on film cooling flow have been done using steady Reynolds-averaged Navier–Stokes calculation procedures. However, the flowfield associated with a jet in a crossflow is highly unsteady and complex with different types of vortical structures. In this paper, a computational investigation about the unsteady phenomena of a jet in a crossflow is performed using detached eddy simulation. Detailed computation of a single row of 35 deg round holes on a flat plate has been obtained for a 1.0 blowing ratio and a 2.0 density ratio. First, time-step size, grid resolution, and computational domain tests for an unsteady simulation have been conducted. Comparison between the results of unsteady Reynolds-averaged Navier–Stokes calculation, detached eddy simulation, and large eddy simulation is also performed. Comparison of the time-averaged detached eddy simulation prediction with the measured film-cooling effectiveness shows that the detached eddy simulation prediction is reasonable. From present detached eddy simulations, the influential coherent vortical structures of a film cooling flow can be seen. The unsteady physics of jet in a crossflow interactions and a jet liftoff in film cooling flows have been explained.

Thermal aspects of satellite downscaling

The strong trend toward nanosatellites creates new challenges in terms of thermal balance control. The thermal balance of a satellite is determined by the heat dissipation in its subsystems and by the thermal connections between them. As satellites become smaller, heat dissipation in their subsystems tends to decrease and thermal connectivity scales down with dimension. However, these two terms do not necessarily scale in the same way, and so the thermal balance may alter and the temperature of subsystems may reach undesired levels. This paper focuses on low-Earth-orbit satellites. We constructed a generalized lumped thermal model that combines a generalized low-Earth-orbit satellite configuration with scaling trends in subsystem heat dissipation and thermal connectivity. Using satellite mass as a scaling parameter, we show that subsystems do not become thermally critical by scaling mass alone.

Interactions between wind-blown snow redistribution and melt ponds in a coupled ocean–sea ice model

Introducing a parameterization of the interactions between wind-driven snow depth changes and melt pond evolution allows us to improve large scale models. In this paper we have implemented an explicit melt pond scheme and, for the first time, a wind dependant snow redistribution model and new snow thermophysics into a coupled ocean–sea ice model. The comparison of long-term mean statistics of melt pond fractions against observations demonstrates realistic melt pond cover on average over Arctic sea ice, but a clear underestimation of the pond coverage on the multi-year ice (MYI) of the western Arctic Ocean. The latter shortcoming originates from the concealing effect of persistent snow on forming ponds, impeding their growth. Analyzing a second simulation with intensified snow drift enables the identification of two distinct modes of sensitivity in the melt pond formation process. First, the larger proportion of wind-transported snow that is lost in leads directly curtails the late spring snow volume on sea ice and facilitates the early development of melt ponds on MYI. In contrast, a combination of higher air temperatures and thinner snow prior to the onset of melting sometimes make the snow cover switch to a regime where it melts entirely and rapidly. In the latter situation, seemingly more frequent on first-year ice (FYI), a smaller snow volume directly relates to a reduced melt pond cover. Notwithstanding, changes in snow and water accumulation on seasonal sea ice is naturally limited, which lessens the impacts of wind-blown snow redistribution on FYI, as compared to those on MYI. At the basin scale, the overall increased melt pond cover results in decreased ice volume via the ice-albedo feedback in summer, which is experienced almost exclusively by MYI.

Aproveitamento da fibra do epicarpo do coco babaçu em compósito com matriz epóxi: estudo do efeito do tratamento da fibra

Nowadays the environmental issues are increasingly highlighted since the future of humanity is dependent on the actions taken by man. Major efforts are being expended in pursuit of knowledge and alternatives to promote sustainable development without compromising the environment. In recent years there has been a marked growth in the development of reinforced composite fiber plants, as an alternative for economic and ecological effects, especially in the substitution of synthetic materials such as reinforcement material in composites. In this current study the chemical- physical or (thermophysics )characteristics of the babassu coconut fiber, derived from the epicarp of the fruit (Orbignyda Phalerata), which the main constituents of the fiber: Klason lignin, insoluble, cellulose, holocellulose, hemicellulose and the content of ash and moisture will be determined. A study was conducted about the superficial modification of the fibers of the epicarp babassu coconut under the influence of chemical treatment by alkalinization, in an aqueous solution of NaOH to 2.5% (m/v) and to 5.0% to improve the compatibility matrix / reinforcement composite with epoxy matrix. The results of the changes occurred in staple fibers through the use of the techniques of thermogravimetric analyses (TG) and differential scanning calorimetry (DSC). The results found on thermal analysis on samples of fiber without chemical treatment (alkalinities), and on fiber samples treated by alkalinization show that the proposed chemical treatment increases the thermal stability of the fibers and provides a growth of the surface of area fibers, parameters that enhance adhesion fiber / composite. The findings were evaluated and compared with published results from other vegetable fibers, showing that the use of babassu coconut fibers has technical and economic potential for its use as reinforcement in composites