EC28-36 Spraying Tree Fruits (Revised March 1932)

The production of sound, clean fruit is unquestionably one of the major problems facing the modern fruit grower. Culture may be neglected and pruning delayed for a time but the omission of sprays for even a single season demonstrates their absolute necessity. This applies equally to the commercial grower and to the farmer or gardener who has only a few trees. Spray materials, equipment, management, schedules, insect pests and orchard diseases are discussed in this 1928 extension circular.

TRANSVERSAL DISTRIBUTION COMPARISON OF SOLID FERTILIZERS APPLIED OVER ANNUAL CROPS

Centrifugal spreaders dominate the application of solid materials in agriculture offering expressive operational field capacity and extended range of applied rates. Field tests for characterization of theirperformance are conducted without any physical obstacles (such as the presence of plants) during the parabolic trajectory of the falling particles of fertilizer to the soil. The purpose of this study was to comparatively evaluate the transverse distribution of solid fertilizers applied on cropped corn, soybeans and cotton. Evaluations of the spreaders were designed according to ASAE S341.3/99 Standard. Tests consisted in aligning side by side collectors in-between the cropped rows and weighting the material deposited. The results showed that transverse distribution of solid fertilizers applied over the cotton and corn crops is affected by the crop height, interfering directly on the effective width of the spreader application, which was not observedin the soybean crop, once the fertilizer application is done when the crop was still below the collector's height. The results suggest that evaluation of effective width of the spreaders application need to be done under real crop environment.

A spatial stochastic model for rumor transmission

We consider an interacting particle system representing the spread of a rumor by agents on the d-dimensional integer lattice. Each agent may be in any of the three states belonging to the set {0,1,2}. Here 0 stands for ignorants, 1 for spreaders and 2 for stiflers. A spreader tells the rumor to any of its (nearest) ignorant neighbors at rate lambda. At rate alpha a spreader becomes a stifler due to the action of other (nearest neighbor) spreaders. Finally, spreaders and stiflers forget the rumor at rate one. We study sufficient conditions under which the rumor either becomes extinct or survives with positive probability.

Rastrojo de arroz (Oryza sativa L.) en sistemas de siembra directa : alternativas de manejo

Los objetivos principales del presente trabajo fueron: a) Estudiar cuál es el uso adecuado de las distintas herramientas para mejorar la mineralización del rastrojo de la cosecha de arroz (Oryza sativa L.) bajo siembra directa y b) Determinar, para períodos cortos, la cantidad de rastrojo depositado superficialmente y su tiempo de mineralización al utilizar las distintas técnicas de manejo del mismo. Los tratamientos fueron: cosechadora con desparramador deflector (T1DD), cosechadora sin desparramador triturador (T2SDT), cosechadora con desparramador centrífugo de caucho (T3DC) y cosechadora con desparramador metálico (T4DM). Alternativas implementadas: a) desmalezado b) rolo cuchilla y c) quemado de rastrojo. En las primeras dos alternativas, se aplicaron tres dosis de urea. Los resultados principales fueron: a) La T2SDT produjo, una mayor deposición de material en el centro de la máquina (21680 kg ha-1), b) la distribución de rastrojo de la (T3DC) fue más uniforme que para los otros tratamientos. Las principales conclusiones fueron: 1) Los desparramadores centrífugos de caucho y metálico produjeron mejor distribución del material, 2) El uso de desmalezadora o rolo cuchilla sobre rastrojo de los tratamientos T3DC y T4DM aceleró la mineralización de los mismos. 3) Las dosis de urea causó poco incremento en la mineralización del rastrojo.

Analysis of thermo-mechanical stress effects on CPV receiver under high intensity light cycles

After construction of the LYSS (Light cYcling Stressing Source) in early 2014, several CPV receivers, with and without secondary optical element (SOE) have been aged under fast transient illumination cycling,. The test plan for Madrid consisted of 50000 cycles. Receivers with poor heat spreaders showed low reliability but those with thicker metal layers passed the test well. The operation of LYSS along 8 months, after more than 250000 cycles, did not show any significant failure, except lamp reposition every 120 hours, in average. The equipment seems valid for unveiling weak receiver designs with respect to intensive illumination, in steady and transient modes.

Advanced thermal analysis of microelectronics using spreading resistance models

Thermal analysis of electronic devices is one of the most important steps for designing of modern devices. Precise thermal analysis is essential for designing an effective thermal management system of modern electronic devices such as batteries, LEDs, microelectronics, ICs, circuit boards, semiconductors and heat spreaders. For having a precise thermal analysis, the temperature profile and thermal spreading resistance of the device should be calculated by considering the geometry, property and boundary conditions. Thermal spreading resistance occurs when heat enters through a portion of a surface and flows by conduction. It is the primary source of thermal resistance when heat flows from a tiny heat source to a thin and wide heat spreader. In this thesis, analytical models for modeling the temperature behavior and thermal resistance in some common geometries of microelectronic devices such as heat channels and heat tubes are investigated. Different boundary conditions for the system are considered. Along the source plane, a combination of discretely specified heat flux, specified temperatures and adiabatic condition are studied. Along the walls of the system, adiabatic or convective cooling boundary conditions are assumed. Along the sink plane, convective cooling with constant or variable heat transfer coefficient are considered. Also, the effect of orthotropic properties is discussed. This thesis contains nine chapters. Chapter one is the introduction and shows the concepts of thermal spreading resistance besides the originality and importance of the work. Chapter two reviews the literatures on the thermal spreading resistance in the past fifty years with a focus on the recent advances. In chapters three and four, thermal resistance of a twodimensional flux channel with non-uniform convection coefficient in the heat sink plane is studied. The non-uniform convection is modeled by using two functions than can simulate a wide variety of different heat sink configurations. In chapter five, a non-symmetrical flux channel with different heat transfer coefficient along the right and left edges and sink plane is analytically modeled. Due to the edge cooling and non-symmetry, the eigenvalues of the system are defined using the heat transfer coefficient on both edges and for satisfying the orthogonality condition, a normalized function is calculated. In chapter six, thermal behavior of two-dimensional rectangular flux channel with arbitrary boundary conditions on the source plane is presented. The boundary condition along the source plane can be a combination of the first kind boundary condition (Dirichlet or prescribed temperature) and the second kind boundary condition (Neumann or prescribed heat flux). The proposed solution can be used for modeling the flux channels with numerous different source plane boundary conditions without any limitations in the number and position of heat sources. In chapter seven, temperature profile of a circular flux tube with discretely specified boundary conditions along the source plane is presented. Also, the effect of orthotropic properties are discussed. In chapter 8, a three-dimensional rectangular flux channel with a non-uniform heat convection along the heat sink plane is analytically modeled. In chapter nine, a summary of the achievements is presented and some systems are proposed for the future studies. It is worth mentioning that all the models and case studies in the thesis are compared with the Finite Element Method (FEM).