Report of the Workshop on Intelligent Compaction for Soils and HMA, April 2-4, 2008

This document summarizes the discussion and findings of a workshop on intelligent compaction for soils and hot-mix asphalt held in West Des Moines, Iowa, on April 2–4, 2008. The objective of the meeting was to provide a collaborative exchange of ideas for developing research initiatives that accelerate implementation of intelligent compaction (IC) technologies for soil, aggregates, and hot mix asphalt. Technical presentations, working breakout sessions, a panel discussion, and a group implementation strategy session comprised the workshop activities. About 100 attendees representing state departments of transportation, Federal Highway Administration, contractors, equipment manufacturers, and researchers participated in the workshop.

Effect of cropping systems in no-till farming on the quality of a Brazilian Oxisol

The no-till system with complex cropping sequences may improve the structural quality and carbon (C) sequestration in soils of the tropics. Thus, the objective of this study was to evaluate the effects of cropping sequences after eight years under the no-till system on the physical properties and C sequestration in an Oxisol in the municipality of Jaboticabal, Sao Paulo, Brazil. A randomized split-block design with three replications was used. The treatments were combinations of three summer cropping sequences - corn/corn (Zea mays L.) (CC), soybean/soybean (Glycine max L. Merryll) (SS), and soybean-corn (SC); and seven winter crops - corn, sunflower (Helianthus annuus L.), oilseed radish (Raphanus sativus L.), pearl millet (Pennisetum americanum (L.) Leeke), pigeon pea (Cajanus cajan (L.) Millsp), grain sorghum (Sorghum bicolor (L.) Moench), and sunn hemp (Crotalaria juncea L.). Soil samples were taken at the 0-10 cm depth after eight years of experimentation. Soil under SC and CC had higher mean weight diameter (3.63 and 3.55 mm, respectively) and geometric mean diameter (3.55 and 2.92 mm) of the aggregates compared to soil under SS (3.18 and 2.46 mm). The CC resulted in the highest soil organic C content (17.07 g kg-1), soil C stock (15.70 Mg ha-1), and rate of C sequestration (0.70 Mg ha-1 yr-1) among the summer crops. Among the winter crops, soil under pigeon pea had the highest total porosity (0.50 m³ m-3), and that under sunn hemp had the highest water stable aggregates (93.74 %). In addition, sunn hemp did not differ from grain sorghum and contained the highest soil organic C content (16.82 g kg-1) and also had the highest rate of C sequestration (0.67 Mg ha-1 yr-1). The soil resistance to penetration was the lower limit of the least limiting water range, while the upper limit was air-filled porosity for soil bulk densities higher than 1.39 kg dm-3 for all cropping sequences. Within the SC sequence, soil under corn and pigeon pea increased least limiting water range by formation of biopores because soil resistance to penetration decreased with the increase in soil bulk density.

Aggregate stability by the "high energy moisture characteristic" method in an oxisol under differentiated management

Studies testing the High Energy Moisture Characteristic (HEMC) technique in tropical soils are still incipient. By this method, the effects of different management systems can be evaluated. This study investigated the aggregation state of an Oxisol under coffee with Brachiaria between crop rows and surface-applied gypsum rates using HEMC. Soil in an experimental area in the Upper São Francisco region, Minas Gerais, was studied at depths of 0.05 and 0.20 m in coffee rows. The treatments consisted of 0, 7, and 28 Mg ha-1 of agricultural gypsum rates distributed on the soil surface of the coffee rows, between which Brachiaria was grown and periodically cut, and compared with a treatment without Brachiaria between coffee rows and no gypsum application. To determine the aggregation state using the HEMC method, soil aggregates were placed in a Büchner funnel (500 mL) and wetted using a peristaltic pump with a volumetric syringe. The wetting was applied increasingly at two pre-set speeds: slow (2 mm h-1) and fast (100 mm h-1). Once saturated, the aggregates were exposed to a gradually increasing tension by the displacement of a water column (varying from 0 to 30 cm) to obtain the moisture retention curve [M = f (Ψ) ], underlying the calculation of the stability parameters: modal suction, volume of drainable pores (VDP), stability index (slow and fast), VDP ratio, and stability ratio. The HEMC method conferred sensitivity in quantifying the aggregate stability parameters, and independent of whether gypsum was used, the soil managed with Brachiaria between the coffee rows, with regular cuts discharged in the crop row direction, exhibited a decreased susceptibility to disaggregation.

Hydro-Physical Properties of a Typic Hapludult under the Effect of Rice Husk Ash

ABSTRACT The combustion of rice husk generates a partially burnt mixture called rice husk ash (RHA) that can be used as a source of nutrients to crops and as a conditioner of soil physical properties. The objective of this study was to evaluate the effect of RHA levels on the hydro-physical properties of a Typic Hapludult. The experimental design was composed of random blocks with four replications, which comprised plots of 24 m2 and treatments with increasing RHA rates: 0, 40, 80 and 120 Mg ha-1. Undisturbed soil samples were collected in the soil layers of 0.00-0.10 and 0.10-0.20 m after nine months of RHA application, using steel cylinders (0.03 m of height and 0.047 m of diameter). These samples were used to determine soil bulk density (Bd), total soil porosity (TP), soil macroporosity (Ma), soil microporosity (Mi) and the available water capacity (AWC). Disturbed soil samples were collected to determine the stability of soil aggregates in water, mean weight diameter of water stable aggregates (MWD), and soil particle size distribution. The results show that, as the RHA rate increased in the soil, Bd values decreased and TP, Ma and MWD values increased. No effect of RHA was found on Mi and AWC values. The effects of RHA on the S parameter (Dexter, 2004), precompression stress and compression index (Dias Junior and Pierce, 1995) values are consistent those shown for density and total porosity. Rice husk ash was shown to be an efficient residue to improve soil physical properties, mainly at rates between 40 and 80 Mg ha-1. Rice husk ash reduces bulk density and increases total porosity, macroporosity and soil aggregation, but does not affect microporosity, field capacity, permanent wilting point, and available water capacity of the soil. The effect of rice husk ash on the S parameter, precompression stress and index compressibility coefficient values are consistent with those observed for the bulk density and total porosity.

Spatial variability of physical attributes of an alfisol under different hillslope curvatures

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estoque de carbono e estabilidade de agregados de um latossolo vermelho distrófico, sob diferentes manejos

These systems of soil use and management are very important in carbon supply and stability of aggregates, because affect directly culture yields. The aim of this project is to evaluate the carbon supply and stability of Haplustox aggregates under different managements. It was utilized a completely randomized experimental design in split plot scheme, with six replications. Thus, the treatments utilized were three different soil managements ( native forest, pasture with Tanzania grass and corn). The plots were consisted by three layers (0-10; 10-20 and 20-30 cm) and were analyzed to determined the organic matter, organic carbon supply of soil ( layers and equivalent soil mass methods) and weighed average diameter (DMP) and geometrical average diameter (DMG). The results indicated that the evaluated managements systems affected the size of soil aggregates of the ground and in its distribution in the layer of 0-30 cm of depth. The greatest accumulation of carbon were in the surface layers, although, there were not variation between the management systems.

Carbohydrate Composition and Water-Stable Aggregation of an Oxisol as Affected by Crop Sequence under No-Till

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Agregação de ume nitossolo vermelho distroférrico sob sistemas de plantio direto, preparo convencional e mata nativa

This study aimed to evaluate the effect of time since the adoption of the no-till system, in comparison with a native forest area and a conventional tillage area, using the distribution of soil aggregates in a Distroferric Red Nitosol. Treatments were as follows: native forest (NF), conventional tillage (CT), no-till for one year (NT1), no-till for four years (NT4), no-till for five years (NT5), and no-till for 12 years (NT12). Aggregate samples were collected randomly within each treatment at depths of 0-5 and 10-15 cm. After sifting the aggregates in water they were separated into the following aggregate classes > 2 mm; < 2 mm; 2-1 mm, and < 1 mm. The adoption time in the no-till system favored soil aggregation. The mean weighted diameter (MWD) of the soil aggregates and the percentage of aggregates greater than 2 mm increased with adoption time in the no-till system at the 0-5 cm depth. The NF and NT12 treatments had higher MWD values in the 0-5 cm layer. CT had the highest percentage of aggregates smaller than 1 mm.

Gênese de solos derivados de rochas ultramáficas serpentinizadas no sudoeste de Minas Gerais

Os solos derivados de rochas serpentinizadas ou serpentinitos constituem um grupo especial de solos em toda superfície terrestre. de caráter ultramáfico, ou seja, rochas com mais de 70 % de minerais máficos (ferromagnesianos), os serpentinitos apresentam uma mineralogia pobre em sílica e escassa em Al, sendo, no entanto, muito enriquecida em Mg. São poucos os estudos sobre a morfologia, mineralogia, gênese e classificação dos solos desenvolvidos de tais rochas. em ambiente tropical úmido no sudoeste de Minas Gerais, na zona do greenstone belt do Morro de Ferro, em superfícies geomórficas jovens, três perfis de solos representativos dessa paisagem sobre rochas serpentinizadas foram caracterizados por meio de descrições macro e micromorfológicas, análises granulométricas, químicas e por mineralogia de raios X das frações argila e silte. Complementarmente, para acompanhamento da alteração geoquímica dos horizontes do solo, foram feitas microanálises das seções delgadas por EDRX. Os solos foram classificados como Chernossolo Háplico Férrico típico, Cambissolo Háplico eutroférrico léptico e Neossolo Regolítico eutrófico típico e, embora situados num clima que favorece o rápido intemperismo, do ponto de vista morfológico e mineralógico, mostraram-se similares aos solos derivados de rochas serpentinizadas das regiões subtropicais e temperada. No processo de formação de solo, a evolução da trama segue a seguinte seqüência: alteração da rocha ® trama frâgmica ® trama porfírica com cavidades ® trama porfírica aberta por coalescência de cavidades. O processo de argiluviação é evidente e se dá em dois estádios distintos: argiluviação primária, que ocorre nas fendas e cavidades que se formam por alteração de rocha, e argiluviação secundária, verificada na porosidade mais aberta e evoluída da coalescência das cavidades. Os solos apresentam mineralogia pouco comum para solos tropicais, com presença de minerais primários de fácil decomposição até mesmo na fração argila, com destaque para o talco, clorita trioctaedral e ocorrência limitada de tremolita, sendo esta última abundante na fração silte. Óxidos de Fe, caulinita e os interestratificados de clorita-esmectita e de clorita-vermiculita completam a assembléia mineralógica. A tendência de evolução é para B textural ou para B nítico com mineralogia 1:1 e alto conteúdo de óxidos de Fe. Nas fases iniciais de alteração, os alteromorfos já apresentam composição química similar aos agregados do solo, com forte perda de Mg, Ca e Si e acúmulo relativo de Al e Fe. Nas três situações estudadas, ocorreu um rejuvenescimento superficial por erosão diferencial, que acumulou material grosseiro e removeu os finos, contribuindo para o incremento da relação textural.

Agregação de um latossolo vermelho submetido a cinco sistemas de preparo do solo em Uberaba - MG

Visando à obtenção de dados relativos aos efeitos de sistemas de preparo periódico do solo e sua relação com a degradação do solo e a capacidade de incorporação de resíduos, avaliaram-se a distribuição percentual de agregados do solo, o diâmetro médio geométrico, o módulo de finura e a incorporação de resíduos, durante o ano agrícola de 2001-2002. A área em estudo foi classificada como Latossolo Vermelho distrófico, localizada no município de Uberaba - MG. Utilizou-se do delineamento estatístico em blocos casualizados com quatro repetições, tendo como tratamentos o preparo periódico primário do solo com o escarificador, enxada rotativa, arado de aivecas, grade aradora e arado de discos. As análises dos resultados mostraram a enxada rotativa e a grade aradora como os equipamentos mais agressivos à estrutura do solo. O escarificador e a enxada rotativa apresentaram menor capacidade de incorporação dos resíduos vegetais. O escarificador manteve maior cobertura vegetal e maior grau de agregação do solo.

Propriedades físicas de um latossolo vermelho cultivado no sistema plantio direto

The pressure caused by agricultural machinery traffic many result in soil compactation in no-tillage system. The aim of this work was to evaluate no-tillage system onset,time on some physical properties, index S and organic matter (OM) of an oxysol located in Jaboticabal, Sao Paulo State, Brazil. The experiment had completely randomized split-splot design. The treatments consisted of four no-tillage systems: no-tillage for 2 years, no-tillage for 4 years, no-tillage for 6 years and one natural wooded area. The evaluated layers were: Q-0.10m, 0.10-0.20m and 0.20-030m. The following were determined: soil porosity, soil aggregates, bulk density, index S and organic matter. The results were submitted to variance analysis and when there was a difference between averages, Tukey's test was used to compare them. The natural wooded area showed higher organic matter, macroporosity, hydraulic conductivity and Index S. There was no difference between the studied parameters, showing that the no-tillage system for six years was not enough to change the soil physical property.

Aggregate shape and tensile strength measurement

Tensile strength (TS) of soil aggregates is an important indicator of soil quality. However, TS varies with aggregate shape. Thus, the objective of this study was to quantify the influence of aggregate shape on TS and propose a shape standardization protocol to increase accuracy in the measurement of TS. The latter was determined on 7,560 aggregates divided into three shapes, (i) irregular shape (IS), (ii) spherical shape (SS), and (iii) flat surface (FS), while preserving the inherent structure of the aggregate. The aggregates with IS had a larger range in the TS (306 kPa) because of the shape variability when compared with SS (238 kPa) and FS (129 kPa). The TS determined in aggregates with FS had smaller coefficient of variation (46%) in comparison with those of IS (70%) and SS (66%), indicating that the aggregate uniformity reduced the influence of shape on the TS. A smaller force (42.12 kPa) was needed to rupture aggregates with FS than IS (58.43 kPa) and SS (56.89 kPa) because of better force distribution in causing the tensile stress. The use of aggregates with the FS enables an accurate assessment of TS in relation to a wide range of management treatments. Copyright © 2013 by Lippincott Williams & Wilkins.

Propriedades físico-químicas e produção da Brachiaria brizantha em um latossolo vermelho fertilizado com Ajifer L-14

Pós-graduação em Agronomia - FEIS

Sistemas de uso e manejo do solo: acúmulo de carbono e atributos físicos

Pós-graduação em Agronomia (Produção Vegetal) - FCAV

Alterações em latossolo vermelho e na cultura da soja em função de sistemas de preparo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)