High performance non-volatile ferroelectric copolymer memory based on a ZnO nanowire transistor fabricated on a transparent substrate

A high performance ferroelectric non-volatile memory device based on a top-gate ZnO nanowire (NW) transistor fabricated on a glass substrate is demonstrated. The ZnO NW channel was spin-coated with a poly (vinylidenefluoride-co-trifluoroethylene) (P(VDF-TrFE)) layer acting as a top-gate dielectric without buffer layer. Electrical conductance modulation and memory hysteresis are achieved by a gate electric field induced reversible electrical polarization switching of the P(VDF-TrFE) thin film. Furthermore, the fabricated device exhibits a memory window of ∼16.5 V, a high drain current on/off ratio of ∼105, a gate leakage current below ∼300 pA, and excellent retention characteristics for over 104 s. © 2014 AIP Publishing LLC.

土壤持水特征测定中质量含水量、吸力和容重三者间定量关系I.填装土壤

在试验过程中,通常采用一个土样进行连续试验来测定土壤的持水特征。此时,土样的有机质、黏粒矿物类型和阳离子交换量等性质基本保持不变,而土壤的容重在水力学和机械压力共同作用下会发生很大的变化。因此,我们认为实测的土壤持水特征不再是土壤吸力和含水量相对应的一条曲线,而是由土壤质量含水量、吸力和容重三变量共同确定的一个曲面。本文在Brooks-Corey土壤水分特征曲线模型的基础上,提出了两种描述土壤质量含水量、吸力和容重三变量关系的曲面模型,分析了模型的优缺点和适用条件,并采用离心机石蜡控容重法实测了四种质地填装土壤的三变量特征曲面。研究结果表明:土壤持水特征是由土壤质量含水量、吸力和容重三变量共同确定的一个曲面这一假设是合理的;类似于Brooks-Corey模型的两种幂函数经验曲面模型能够合理地描述填装土壤的实测数据,决定系数均大于0.94;模型Ⅰ的拟合效果略好于模型Ⅱ,但模型Ⅱ包含两个物理意义明确的参数,具有一定的优势。这一研究将为校正容重变化对土壤水力学参数的影响提供新的途径。

Fullerenes-extracted soot: a new adsorbent for collecting volatile organic compounds in ambient air

Fullerenes-extracted soot (FES) is the by-product of fullerenes production. Retention characteristics at different temperatures for 17 volatile organic compounds (VOCs) on FES are measured. The adsorption and desorption efficiencies for VOCs on FES adsorbent tubes range from 40.8 to 117%, most of them being 100+/-20%. The values are compared with Tenax GR, an adsorbent commonly used in environmental analysis. FES can be used as an adsorbent of low cost to collect VOCs in environmental samples. (C) 2000 Elsevier Science B.V. All rights reserved.

花岗岩风化土微观结构及其工程地质特性研究

Saprolite is the residual soil resulted from completely weathered or highly weathered granite and with corestones of parent rock. It is widely distributed in Hong Kong. Slope instability usually happens in this layer of residual soil and thus it is very important to study the engineering geological properties of Saprolite. Due to the relic granitic texture, the deformation and strength characteristics of Saprolite are very different from normal residual soils. In order to investigate the effects of the special microstructure on soil deformation and strength, a series of physical, chemical and mechanical tests were conducted on Saprolite at Kowloon, Hong Kong. The tests include chemical analysis, particle size analysis, mineral composition analysis, mercury injection, consolidation test, direct shear test, triaxial shear test, optical analysis, SEM & TEM analysis, and triaxial shear tests under real-time CT monitoring.Based on the testing results, intensity and degree of weathering were classified, factors affecting and controlling the deformation and strength of Saprolite were identified, and the interaction between those factors were analyzed.The major parameters describing soil microstructure were introduced mainly based on optical thin section analysis results. These parameters are of importance and physical meaning to describe particle shape, particle size distribution (PSD), and for numerical modeling of soil microstructure. A few parameters to depict particle geometry were proposed or improved. These parameters can be used to regenerate the particle shape and its distribution. Fractal dimension of particle shape was proposed to describe irregularity of particle shapes and capacity of space filling quantitatively. And the effect of fractal dimension of particle shape on soil strength was analyzed. At the same time, structural coefficient - a combined parameter which can quantify the overall microstructure of rock or soil was introduced to study Saprolite and the results are very positive. The study emphasized on the fractal characteristics of PSD and pore structure by applying fractal theory and method. With the results from thin section analysis and mercury injection, it was shown that at least two fractal dimensions Dfl(DB) and Df2 (Dw), exist for both PSD and pore structure. The reasons and physical meanings behind multi-fractal dimensions were analyzed. The fractal dimensions were used to calculate the formation depth and weathering rate of granite at Kowloon. As practical applications, correlations and mathematical models for fractal dimensions and engineering properties of soil were established. The correlation between fractal dimensions and mechanical properties of soil shows that the internal friction angle is mainly governed by Dfl 9 corresponding to coarse grain components, while the cohesion depends on Df2 , corresponding to fine grain components. The correlations between the fractal dimension, friction angle and cohesion are positive linear.Fractal models of PSD and pore size distribution were derived theoretically. Fragmentation mechanism of grains was also analyzed from the viewpoint of fractal. A simple function was derived to define the theoretical relationship between the water characteristic curve (WCC) and fractal dimension, based on a number of classical WCC models. This relationship provides a new analytical tool and research method for hydraulic properties in porous media and solute transportation. It also endues fractal dimensions with new physical meanings and facilitates applications of fractal dimensions in water retention characteristics, ground water movement, and environmental engineering.Based on the conclusions from the fractal characteristics of Saprolite, size effect on strength was expressed by fractal dimension. This function is in complete agreement with classical Weibull model and a simple function was derived to represent the relationship between them.In this thesis, the phenomenon of multi-fractal dimensions was theoretically analyzed and verified with WCC and saprolite PSD results, it was then concluded that multi-fractal can describe the characteristics of one object more accurately, compared to single fractal dimension. The multi-fractal of saprolite reflects its structural heterogeneity and changeable stress environment during the evolution history.

Tillage and phosphorus management effects on enzyme-labile bioactive phosphorus availability in Cerrado Oxisols

Phosphorus (P) is an essential element in crop nutrition, which can be growth limiting or an environmental contaminant, if present in excess. Tillage practices have a direct effect on the behavior and availability of soil P. Sorption and availability of various P forms were evaluated in an incubation-fractionation study of three soils, a Typic Paleudults (CR soil) and two Cerrado Oxisols (Latossolo Vermelho-Amarelo [LVA] and Latossolo Vermelho [LV]) with distinct biogeochemical characteristics and tillage management history. Phosphate and myo-inositol hexakisphosphate (mIPH) were strongly sorbed by the soils. Maximum adsorption capacities (S(max)) were 2.2-6.9, 3.3-7.8, and 1.6-19.8 mmol kg(-1) for phosphate in the 0-40 cm depths of the CR, LV, and LVA soils, respectively. For mIPH, S. were 1.2-3.7, 3.7-5.5, and 4.6-5.2 mmol kg(-1). Saturation indices reflected the long-term effect of repeated manure applications on the Paleudults and the near saturation of its P holding capacity, in contrast to the recently cultivated Cerrado soils. Tillage method appeared to have altered P retention characteristics of the near-surface zone very slightly, while increases in ligand-exchangeable (EEP;) and enzyme-labile organic P (EDTA-PHP) forms were observed in no-till Oxisols. In the Paleudults, added manure P increased bioactive P fractions and P saturation of no-till near-surface soil zone. Estimates of all bioactive P fractions using the ligand-based enzymatic assay showed it to be an effective method for assessing P availability in soil and developing sustainable P management strategies, particularly in Cerrado Oxisols that were low in organic matter while having an extensive P-fixing capacity. Published by Elsevier B.V.

Field-scale water transport in unsaturated crystalline rock

Safe disposal of toxic wastes in geologic formations requires minimal water and gas movement in the vicinity of storage areas, Ventilation of repository tunnels or caverns built in solid rock can desaturate the near field up to a distance of meters from the rock surface, even when the surrounding geological formation is saturated and under hydrostatic pressures. A tunnel segment at the Grimsel test site located in the Aare granite of the Bernese Alps (central Switzerland) has been subjected to a resaturation and, subsequently, to a controlled desaturation, Using thermocouple psychrometers (TP) and time domain reflectometry (TDR), the water potentials psi and water contents theta were measured within the unsaturated granodiorite matrix near the tunnel wall at depths between 0 and 160 cm. During the resaturation the water potentials in the first 30 cm from the rock surface changed within weeks from values of less than -1.5 MPa to near saturation. They returned to the negative initial values during desaturation, The dynamics of this saturation-desaturation regime could be monitored very sensitively using the thermocouple psychrometers, The TDR measurements indicated that water contents changed dose to the surface, but at deeper installation depths the observed changes were within the experimental noise. The field-measured data of the desaturation cycle were used to test the predictive capabilities of the hydraulic parameter functions that were derived from the water retention characteristics psi(theta) determined in the laboratory. A depth-invariant saturated hydraulic conductivity k(s) = 3.0 x 10(-11) m s(-1) was estimated from the psi(t) data at all measurement depths, using the one-dimensional, unsaturated water flow and transport model HYDRUS Vogel er al., 1996, For individual measurement depths, the estimated k(s) varied between 9.8 x 10(-12) and 6.1 x 10(-11) The fitted k(s) values fell within the range of previously estimated k(s) for this location and led to a satisfactory description of the data, even though the model did not include transport of water vapor.

A numerical study of steady state evaporative conditions applied to mine tailings

The suction profile of a desiccating soil is dependent on the water table depth, the soil-water retention characteristics, and the climatic conditions. In this paper, an unsaturated flow model, which simulates both liquid and vapour flow, was used to investigate the effects of varying the water table depth and the evaporation rate on the evaporative fluxes from a desiccating tailings deposit under steady-state conditions. Results obtained showed that at a critical evaporation rate, beyond which evaporation is no longer dictated by climatic conditions, the matric suction profiles remain basically unchanged. The critical evaporation rate varies inversely with the water table depth. It is associated with the maximum evaporative flux that might be extracted from a soil at steady-state conditions. The time required to establish steady-state conditions is directly proportional to the water table depth, and it acquires a maximum value at the critical evaporation rate. A detailed investigation of the movement of the drying front demonstrated the significance of attaining a matric suction of about 3000 kPa on the contribution to flow in the vapour phase.

Investigation of the effects of low energy high dose ion bombardment in metals and compound semiconductors

The effect of low energy nitrogen molecular ion beam bombardment on metals and compound semiconductors has been studied, with the aim to investigate at the effects of ion and target properties. For this purpose, nitrogen ion implantation in aluminium, iron, copper, gold, GaAs and AIGaAs is studied using XPS and Angle Resolve XPS. A series of experimental studies on N+2 bombardment induced compositional changes, especially the amount of nitrogen retained in the target, were accomplished. Both monoenergetic implantation and non-monoenergetic ion implantation were investigated, using the VG Scientific ESCALAB 200D system and a d. c. plasma cell, respectively. When the samples, with the exception of gold, are exposed to air, native oxide layers are formed on the surfaces. In the case of monoenergetic implantation, the surfaces were cleaned using Ar+ beam bombardment prior to implantation. The materials were then bombarded with N2+ beam and eight sets of successful experiments were performed on each sample, using a rastered N2+ ion beam of energy of 2, 3, 4 and 5 keV with current densities of 1 μA/cm2 and 5 μA/cm22 for each energy. The bombarded samples were examined by ARXPS. After each complete implantation, XPS depth profiles were created using Ar+ beam at energy 2 ke V and current density 2 μA/cm2 . As the current density was chosen as one of the parameters, accurate determination of current density was very important. In the case of glow discharge, two sets of successful experiments were performed in each case, by exposing the samples to nitrogen plasma for the two conditions: at low pressure and high voltage and high pressure and low voltage. These samples were then examined by ARXPS. On the theoretical side, the major problem was prediction of the number of ions of an element that can be implanted in a given matrix. Although the programme is essentially on experimental study, but an attempt is being made to understand the current theoretical models, such as SATVAL, SUSPRE and TRIM. The experimental results were compared with theoretical predictions, in order to gain a better understanding of the mechanisms responsible. From the experimental results, considering possible experimental uncertainties, there is no evidence of significant variation in nitrogen saturation concentration with ion energy or ion current density in the range of 2-5 ke V, however, the retention characteristics of implantant seem to strongly depend on the chemical reactivity between ion species and target material. The experimental data suggests the presence of at least one thermal process. The discrepancy between the theoretical and experimental results could be the inability of the codes to account for molecular ion impact and thermal processes.

Extrusion of flavored corn grits: Structural characteristics, volatile compounds retention and sensory acceptability

The effects of the moisture content of the raw material, extrusion temperature and screw speed on flavor retention, sensory acceptability and structure of corn grits extrudates flavored with isovaleraldehyde, ethyl butyrate and butyric acid were investigated. Higher temperature resulted in more expanded extrudates with lower density and cutting force, while higher moisture content increased ethyl butyrate retention. The most acceptable extrudates were those obtained with low moisture content, under conditions of high extrusion temperature and high screw speed, or low screw speed and low extrusion temperature, whereas the aroma intensity closest to the ideal was observed under conditions of low extrusion temperature and low moisture content of the raw material. © 2013 Elsevier Ltd.

Pre-extrusion aromatization of a soy protein isolate using volatile compounds and flavor enhancers: Effects on physical characteristics, volatile retention and sensory characteristics of extrudates

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Participation, characteristics and retention rates of HIV-positive immigrants in the Swiss HIV Cohort Study

Data from observational cohorts may be influenced by population structure and loss to follow-up (LTFU). Quality of care may be associated with participation in cohort networks. We aimed to study the participation, characteristics and retention rates of immigrants in the Swiss HIV Cohort Study (SHCS).

Influence of sludge retention time on filtration performance and biomass characteristics in a hollow fiber membrane bioreactor

In this study, the filtration process and the biomass characteristics in a laboratory-scale submerged membrane bioreactor (MBR) equipped with a hollow fiber (HF) microfiltration membrane were studied at different solid retention times (SRT). The MBR was fed by synthetic wastewater and the organic loading rate (OLR) was 0.5, 0.2, 0.1, and 0.08 kg COD kg VSS−1 d−1 for 10, 30, 60, and 90 days of SRT, respectively. The hydraulic retention time was 8.4 h and the permeate flux was 6 L m−2 h−1(LMH). Data analysis confirmed that at all the studied SRTs, the HF-MBR operated very good obtaining of high quality permeates. Chemical Oxygen Demand (COD) removal efficiencies were higher than 95%. The best filtration performance was reached at SRT of 30 d. On the other hand, the respirometric analysis showed that biomass was more active and there was more biomass production at low SRTs. The concentration of soluble extracellular polymeric substances (EPS) decreased with increasing SRT. A decrease of soluble EPS caused a decrease of membrane fouling rate, decreasing the frequency of chemical cleanings. The floc size decreased with SRT increasing. At high SRTs, there was more friction among particles due to the increase of the cellular density and the flocs broke decreasing their size.

Relationship between bicarbonate retention and bone characteristics in broiler chickens

Determination of the bicarbonate retention factor (BRF) is an important step during development of the indicator amino acid oxidation technique for use in a new model. A series of 4-h oxidation experiments were performed to determine the BRF of broilers aged 7, 14, 21, 28, 35, and 42 d using 4 birds per age group. A priming dose of 1.2 mu Ci of (NaHCO3)-C-14, followed by eight half-hourly doses of 1 mu Ci of (NaHCO3)-C-14 were given orally to each of 4 birds per age. The percentage of 14 C dose expired by the bird at a steady state was measured. These birds, as well as 12 additional birds matched for age and BW, were killed, and femur bone mineral density was measured by quantitative computed tomography to determine the relationship between bone development and bicarbonate retention at each age. There was a correlation (r = 0.50; P < 0.05) between total cross-sectional femur bone mineral density and bicarbonate retention at each age. A prediction equation (Y = 6.95 x 10(-2) X - 3.51 x 10(5)X(2) + 27.58; P < 0.0001, R-2 = 0.79) where Y = bicarbonate retention and X = BW was generated to predict Y as a function of X. Bicarbonate retention values peaked at 28 d, during the stage of the most rapid bone deposition and the highest growth rate. A constant BRF was found from 1,900 to 2,700 g of BW of 35.15 +/- 1.095% (mean SEM). This retention factor will allow the accurate correction of oxidation of C-14-labeled substrates in broilers of different ages and BW in future indicator amino acid oxidation studies.

Supervision practices in allied mental health : relationships of supervision characteristics to perceived impact and job satisfaction

This study examined whether supervision characteristics impacted on mental health practice and morale, and developed a new Supervision Attitude Scale (SAS). Telephone surveys were conducted with a representative sample of 272 staff from public mental health services across Queensland. Although supervision was widely received and positively rated, it had low average intensity, and assessment and training of skills was rarely incorporated. Perceived impact on practice was associated with acquisition of skills and positive attitudes to supervisors, but extent of supervision was related to impact only if it was from within the profession. Intention to resign was unrelated to extent of supervision, but was associated with positive attitudes to supervisors, accessibility, high impact, and empathy or praise in supervision sessions. The SAS had high internal consistency, and its intercorrelations were consistent with it being a measure of relationship positivity. The study supported the role of supervision in retention and in improving practice. It also highlighted supervision characteristics that might be targeted in training, and provided preliminary data on a new measure.

Verifying a Student Engagement, Success and Retention Maturity Model (SESR-MM): A reality check of the model using data derived from three universities

Australian higher education institutions (HEIs) have entered a new phase of regulation and accreditation which includes performance-based funding relating to the participation and retention of students from social and cultural groups previously underrepresented in higher education. However, in addressing these priorities, it is critical that HEIs do not further disadvantage students from certain groups by identifying them for attention because of their social or cultural backgrounds, circumstances which are largely beyond the control of students. In response, many HEIs are focusing effort on university-wide approaches to enhancing the student experience because such approaches will enhance the engagement, success and retention of all students, and in doing so, particularly benefit those students who come from underrepresented groups. Measuring and benchmarking student experiences and engagement that arise from these efforts is well supported by extensive collections of student experience survey data. However no comparable instrument exists that measures the capability of institutions to influence and/or enhance student experiences where capability is an indication of how well an organisational process does what it is designed to do (Rosemann & de Bruin, 2005). We have proposed that the concept of a maturity model (Marshall, 2010; Paulk, 1999) may be useful as a way of assessing the capability of HEIs to provide and implement student engagement, success and retention activities and we are currently articulating a Student Engagement, Success and Retention Maturity Model (SESR-MM), (Clarke, Nelson & Stoodley, 2012; Nelson, Clarke & Stoodley, 2012). Our research aims to address the current gap by facilitating the development of an SESR-MM instrument that aims (i) to enable institutions to assess the capability of their current student engagement and retention programs and strategies to influence and respond to student experiences within the institution; and (ii) to provide institutions with the opportunity to understand various practices across the sector with a view to further improving programs and practices relevant to their context. Our research extends the generational approach which has been useful in considering the evolutionary nature of the first year experience (FYE) (Wilson, 2009). Three generations have been identified and explored: First generation approaches that focus on co-curricular strategies (e.g. orientation and peer programs); Second generation approaches that focus on curriculum (e.g. pedagogy, curriculum design, and learning and teaching practice); and third generation approaches—also referred to as transition pedagogy—that focus on the production of an institution-wide integrated holistic intentional blend of curricular and co-curricular activities (Kift, Nelson & Clarke, 2010). Our research also moves beyond assessments of students’ experiences to focus on assessing institutional processes and their capability to influence student engagement. In essence, we propose to develop and use the maturity model concept to produce an instrument that will indicate the capability of HEIs to manage and improve student engagement, success and retention programs and strategies. The issues explored in this workshop are (i) whether the maturity model concept can be usefully applied to provide a measure of institutional capability for SESR; (ii) whether the SESR-MM can be used to assess the maturity of a particular set of institutional practices; and (iii) whether a collective assessment of an institution’s SESR capabilities can provide an indication of the maturity of the institution’s SESR activities. The workshop will be approached in three stages. Firstly, participants will be introduced to the key characteristics of maturity models, followed by a discussion of the SESR-MM and the processes involved in its development. Secondly, participants will be provided with resources to facilitate the development of a maturity model and an assessment instrument for a range of institutional processes and related practices. In the final stage of the workshop, participants will “assess” the capability of these practices to provide a collective assessment of the maturity of these processes. References Australian Council for Educational Research. (n.d.). Australasian Survey of Student Engagement. Retrieved from http://www.acer.edu.au/research/ausse/background Clarke, J., Nelson, K., & Stoodley, I. (2012, July). The Maturity Model concept as framework for assessing the capability of higher education institutions to address student engagement, success and retention: New horizon or false dawn? A Nuts & Bolts presentation at the 15th International Conference on the First Year in Higher Education, “New Horizons,” Brisbane, Australia. Department of Education, Employment and Workplace Relations. (n.d.). The University Experience Survey. Advancing quality in higher education information sheet. Retrieved from http://www.deewr.gov.au/HigherEducation/Policy/Documents/University_Experience_Survey.pdf Kift, S., Nelson, K., & Clarke, J. (2010) Transition pedagogy - a third generation approach to FYE: A case study of policy and practice for the higher education sector. The International Journal of the First Year in Higher Education, 1(1), pp. 1-20. Marshall, S. (2010). A quality framework for continuous improvement of e-Learning: The e-Learning Maturity Model. Journal of Distance Education, 24(1), 143-166. Nelson, K., Clarke, J., & Stoodley, I. (2012). An exploration of the Maturity Model concept as a vehicle for higher education institutions to assess their capability to address student engagement. A work in progress. Submitted for publication. Paulk, M. (1999). Using the Software CMM with good judgment, ASQ Software Quality Professional, 1(3), 19-29. Wilson, K. (2009, June–July). The impact of institutional, programmatic and personal interventions on an effective and sustainable first-year student experience. Keynote address presented at the 12th Pacific Rim First Year in Higher Education Conference, “Preparing for Tomorrow Today: The First Year as Foundation,” Townsville, Australia. Retrieved from http://www.fyhe.com.au/past_papers/papers09/ppts/Keithia_Wilson_paper.pdf