Real-time estimation of transmission line impedance based on modal analysis theory

The objective of this paper is to show a methodology to estimate the longitudinal parameters of transmission lines. The method is based on the modal analysis theory and developed from the currents and voltages measured at the sending and receiving ends of the line. Another proposal is to estimate the line impedance in function of the real-time load apparent power and power factor. The procedure is applied for a non-transposed 440 kV three-phase line. © 2011 IEEE.

Changes in hippocampal gene expression by 7-nitroindazole in rats submitted to forced swimming stress

Nitric oxide (NO) is an atypical neurotransmitter that has been related to the pathophysiology of major depression disorder. Increased plasma NO levels have been reported in depressed and suicidal patients. Inhibition of neuronial nitric oxide synthase (nNOS), on the other hand, induces antidepressant effects in clinical and pre-clinical trials. The mechanisms responsible for the antidepressant-like effects of nNOS inhibitors, however, are not completely understood. In this study, genomic and proteomic analyses were used to investigate the effects of the preferential nNOS inhibitor 7-nitroindazole (7-NI) on changes in global gene and protein expression in the hippocampus of rats submitted to forced swimming test (FST). Chronic treatment (14 days, i.p.) with imipramine (15 mg/kg daily) or 7-NI (60 mg/kg daily) significantly reduced immobility in the FST. Saturation curves for Serial analysis of gene expression libraries showed that the hippocampus of animals submitted to FST presented a lower number of expressed genes compared to non-FST stressed groups. Imipramine, but not 7-NI, reverted this effect. GeneGo analyses revealed that genes related to oxidative phosphorylation, apoptosis and survival controlled by HTR1A signaling and cytoskeleton remodeling controlled by Rho GTPases were significantly changed by FST. 7-NI prevented this effect. In addition, 7-NI treatment changed the expression of genes related to transcription in the cAMP response element-binding pathway. Therefore, this study suggests that changes in oxidative stress and neuroplastic processes could be involved in the antidepressant-like effects induced by nNOS inhibition.

Voice disorders related to job stress in teaching: a case-control study

This case-control study aimed to test the association between voice disorders and job stress among public schoolteachers in Sao Paulo, Brazil. The groups consisted of teachers with (n = 165) and without (n = 105) voice-related complaints. Both groups answered the questionnaires Conditions of Vocal Production and Job Stress Scale. Analysis of cases and controls showed comparable samples, differing only by vocal symptoms. There was a statistically significant difference between cases and controls in relation to job stress involving high strain (OR = 2.1;95%CI: 1.1-3.9), which places high demands combined with low job control. High strain in cases in this study represents the highest risk of physical and mental disorders for teachers. Loss of voice prevents teachers from continuing in their professional role, eliminates their professional identity, and jeopardizes their career.

Villaggio Eugenio Morelli di Sondalo : analisi del complesso sanatoriale e progetto delle nuove passerelle pedonali

Cercare di comprendere l'importanza che il villaggio sanatoriale Eugenio Morelli ha avuto nel passato è fondamentale per capire quali necessità abbiano spinto ad erigere un tale colosso, sulle pendici delle alpi. Ed è proprio da qui che la mia tesi è partita, dalla ricerca storica, dall'analisi degli elementi politici, sanitari e soprattutto sociali che si sono verificati tra la fine dell'ottocento e i primi tre decenni del novecento; periodo in cui la tubercolosi è passata dall'essere un malattia poco considerata, che colpiva solo le classi più povere e disagiate, costrette a vivere nei periferie sovraffollate delle grandi città, all'essere considerata una vera e propria piaga sociale, che dove essere sanata. In questa prima ricerca non si è comunque trascurata l'aspetto architettonico, andando ad analizzare l'evoluzione che hanno visto i sanatori, prima in Europa e poi in particolare in Italia. Valutandone gli aspetti stilistici, formali e soprattutto funzionali, con le tante standardizzazioni che si sono avute sotto il fascismo, e che proprio nel villaggio sanatoriale ritroviamo. In seguito sono passato ad analizzare i lavori sul villaggio effettuati nel dopoguerra, come l'eliminazione della teleferica e la costruzione delle passerelle pedonali, che collegano direttamente i vari padiglioni tra di loro, che vennero aggiunte negli anni 70, da quando cioè la destinazione del complesso è mutata in una funzione ospedaliera. Questo però è avvenuto per una sola parte del complesso, cioè quella che una volta era destinata agli alloggi femminili, mentre la porzione più a ovest è stata lasciata in disuso. In varie sedi si è affrontato il dibattito su come sfruttare le migliaia di metri quadri che gli edifici dismessi offrono, ma fino ad ora non è stata data una nuova vocazione a quest'ultimi. La soluzione più accreditata è quella di cedere parte del villaggio ad una società di ricerca svizzera che lo utilizzerebbe come campus per gli scienziati. Ed è proprio considerando questa possibilità, e tenendo conto dell'attuale porzione destinata all'attività ospedaliera, che si sviluppato il progetto di tesi per le nuove passerelle pedonali, che dovrebbero risultare come un elemento di unione dell'intero villaggio e come elemento che si integra alla moltitudine di percorsi già presenti in esso, dandone una maggior razionalizzazione rispetto a quelle esistenti e trasformando i singoli padiglioni, da unità chiuse che in se stesse trovano la conclusione della loro funzione ad un elemento inserito in una rete funzionale che, con la riattivazione delle teleferiche, attraversa tutto il villaggio

Progetto ed implementazione di protocolli a basso consumo energetico per reti wireless

"I computer del nuovo millennio saranno sempre più invisibili, o meglio embedded, incorporati agli oggetti, ai mobili, anche al nostro corpo. L'intelligenza elettronica sviluppata su silicio diventerà sempre più diffusa e ubiqua. Sarà come un'orchestra di oggetti interattivi, non invasivi e dalla presenza discreta, ovunque". [Mark Weiser, 1991] La visione dell'ubiquitous computing, prevista da Weiser, è ormai molto vicina alla realtà e anticipa una rivoluzione tecnologica nella quale l'elaborazione di dati ha assunto un ruolo sempre più dominante nella nostra vita quotidiana. La rivoluzione porta non solo a vedere l'elaborazione di dati come un'operazione che si può compiere attraverso un computer desktop, legato quindi ad una postazione fissa, ma soprattutto a considerare l'uso della tecnologia come qualcosa di necessario in ogni occasione, in ogni luogo e la diffusione della miniaturizzazione dei dispositivi elettronici e delle tecnologie di comunicazione wireless ha contribuito notevolmente alla realizzazione di questo scenario. La possibilità di avere a disposizione nei luoghi più impensabili sistemi elettronici di piccole dimensioni e autoalimentati ha contribuito allo sviluppo di nuove applicazioni, tra le quali troviamo le WSN (Wireless Sensor Network), ovvero reti formate da dispositivi in grado di monitorare qualsiasi grandezza naturale misurabile e inviare i dati verso sistemi in grado di elaborare e immagazzinare le informazioni raccolte. La novità introdotta dalle reti WSN è rappresentata dalla possibilità di effettuare monitoraggi con continuità delle più diverse grandezze fisiche, il che ha consentito a questa nuova tecnologia l'accesso ad un mercato che prevede una vastità di scenari indefinita. Osservazioni estese sia nello spazio che nel tempo possono essere inoltre utili per poter ricavare informazioni sull'andamento di fenomeni naturali che, se monitorati saltuariamente, non fornirebbero alcuna informazione interessante. Tra i casi d'interesse più rilevanti si possono evidenziare: - segnalazione di emergenze (terremoti, inondazioni) - monitoraggio di parametri difficilmente accessibili all'uomo (frane, ghiacciai) - smart cities (analisi e controllo di illuminazione pubblica, traffico, inquinamento, contatori gas e luce) - monitoraggio di parametri utili al miglioramento di attività produttive (agricoltura intelligente, monitoraggio consumi) - sorveglianza (controllo accessi ad aree riservate, rilevamento della presenza dell'uomo) Il vantaggio rappresentato da un basso consumo energetico, e di conseguenza un tempo di vita della rete elevato, ha come controparte il non elevato range di copertura wireless, valutato nell'ordine delle decine di metri secondo lo standard IEEE 802.15.4. Il monitoraggio di un'area di grandi dimensioni richiede quindi la disposizione di nodi intermedi aventi le funzioni di un router, il cui compito sarà quello di inoltrare i dati ricevuti verso il coordinatore della rete. Il tempo di vita dei nodi intermedi è di notevole importanza perché, in caso di spegnimento, parte delle informazioni raccolte non raggiungerebbero il coordinatore e quindi non verrebbero immagazzinate e analizzate dall'uomo o dai sistemi di controllo. Lo scopo di questa trattazione è la creazione di un protocollo di comunicazione che preveda meccanismi di routing orientati alla ricerca del massimo tempo di vita della rete. Nel capitolo 1 vengono introdotte le WSN descrivendo caratteristiche generali, applicazioni, struttura della rete e architettura hardware richiesta. Nel capitolo 2 viene illustrato l'ambiente di sviluppo del progetto, analizzando le piattaforme hardware, firmware e software sulle quali ci appoggeremo per realizzare il progetto. Verranno descritti anche alcuni strumenti utili per effettuare la programmazione e il debug della rete. Nel capitolo 3 si descrivono i requisiti di progetto e si realizza una mappatura dell'architettura finale. Nel capitolo 4 si sviluppa il protocollo di routing, analizzando i consumi e motivando le scelte progettuali. Nel capitolo 5 vengono presentate le interfacce grafiche utilizzate utili per l'analisi dei dati. Nel capitolo 6 vengono esposti i risultati sperimentali dell'implementazione fissando come obiettivo il massimo lifetime della rete.

Il progetto dell'edificio pubblico nella citta' contemporanea.

La tesi curricolare da me affrontata come elaborato conclusivo del corso di Laurea Specialistica a ciclo unico in Architettura, presso la Scuola di Ingegneria e Architettura dell’Università di Bologna, sede di Cesena, ha come oggetto di studio il percorso didattico formativo da me svolto. Nasce dalla volontà di poter definire un quadro quanto più didascalico, riguardo le attitudini teorico/pratiche approfondite e applicate nell’ambito dei Laboratori di Progettazione III e IV, entrambi riguardanti progetti di trasformazione del volto urbano di una città, a scale differenti.

Un luogo sospeso nel tempo - progetto di restauro e valorizzazione per Villa Cesarini e il suo parco.

Situata nel comune di Corinaldo (AN), questa dimora signorile viene edificata su precedenti resti dal botanico Paolo Spadoni attorno alla metà del Settecento. Passata poi in mano a diversi proprietari, di cui l’ultimo risulta essere il Conte Giacomo Cesarini Romaldi, assume attorno agli inizi del novecento l’attuale aspetto. L’intero sistema si compone di diverse parti: la residenza del signore, la chiesa, la limonaia, la stalla, la rimessa delle carrozze e la casa del custode, connessi tra loro dal grande parco di circa due ettari di superficie, all’interno del quale sono disseminati innumerevoli manufatti, grotte e reperti archeologici. La presente tesi si pone come obiettivo quello di proporre un progetto di restauro che risponda alla richiesta del luogo di essere salvato; in esso sono stati riconosciuti dei valori che vanno necessariamente recuperati e trasmessi.

Milano. Progetto di riassetto urbano dell'ex caserma mameli. I tracciati come fatto urbano.

Riscrivere la storia di un luogo urbano, risolverlo sviluppando un sistema progettuale complesso, rende necessario cogliere le caratteristiche stesse del luogo, individuare le possibilità e le potenzialità strutturali che lo spazio offre e svelare rapporti talvolta sottesi. Il progetto ha origine dalle necessità e da esse trae forza: l’architettura ideata deriva direttamente dal confronto tra il luogo, la sua storia e le sue trasformazioni, e gli esempi, le architetture che conosciamo, quelle costruite e quelle soltanto disegnate. La risoluzione della Caserma Mameli, la restituzione del suo spazio alla grande città, l’auspicabile creazione di un nuovo nucleo di riferimento per la zona Milano Nord, porta a riflettere sull’importanza del riutilizzo urbano al fine di ottenere nuove unioni e sinergie all’interno del complesso schema della città del XXI secolo. La città contemporanea, in continua trasformazione, vive un’epoca di profondi cambiamenti: si intende progettare e pensare la città in maniera sostenibile, limitando l’impatto della nuova costruzione, favorendo il riutilizzo, urbano ed umano, sviluppando reti sempre più estese per la mobilità collettiva e cercando di limitare quanto più possibile la mera speculazione.

CCN2/CTGF is required for matrix organization and to protect growth plate chondrocytes from cellular stress

CCN2 (connective tissue growth factor (CTGF/CCN2)) is a matricellular protein that utilizes integrins to regulate cell proliferation, migration and survival. The loss of CCN2 leads to perinatal lethality resulting from a severe chondrodysplasia. Upon closer inspection of Ccn2 mutant mice, we observed defects in extracellular matrix (ECM) organization and hypothesized that the severe chondrodysplasia caused by loss of CCN2 might be associated with defective chondrocyte survival. Ccn2 mutant growth plate chondrocytes exhibited enlarged endoplasmic reticula (ER), suggesting cellular stress. Immunofluorescence analysis confirmed elevated stress in Ccn2 mutants, with reduced stress observed in Ccn2 overexpressing transgenic mice. In vitro studies revealed that Ccn2 is a stress responsive gene in chondrocytes. The elevated stress observed in Ccn2-/- chondrocytes is direct and mediated in part through integrin α5. The expression of the survival marker NFκB and components of the autophagy pathway were decreased in Ccn2 mutant growth plates, suggesting that CCN2 may be involved in mediating chondrocyte survival. These data demonstrate that absence of a matricellular protein can result in increased cellular stress and highlight a novel protective role for CCN2 in chondrocyte survival. The severe chondrodysplasia caused by the loss of CCN2 may be due to increased chondrocyte stress and defective activation of autophagy pathways, leading to decreased cellular survival. These effects may be mediated through nuclear factor κB (NFκB) as part of a CCN2/integrin/NFκB signaling cascade.

Preliminary results and documentation of sediment cores CRP2 and CRP-2A from the Ross Sea off Cape Roberts, Antarctica

The site for CRP-2, 14 km east of Cape Roberts (77.006°S; 163.719°E), was selected to overlap the early Miocene strata cored in nearby CRP-1, and to sample deeper into the east-dipping strata near the western margin ofe he Victoria Land Basin to investigate Palaeogene climatic and tectonic history. CRP-2 was cored from 5 to 57 mbsf (metres below the sea floor) (core recovery 91 %), with a deviation resulting in CRP-2A being cored at the same site. CRP-2A reached down to 624mbsf (recovery 95%), and to strata with an age of c. 33-35 Ma. Drilling took place from 16 October to 25 November 1998, on 2.0-2.2 m of sea ice and through 178 m of water. Core fractures and other physical properties, such as sonic velocity, density and magnetic susceptibility, were measured throughout the core. Down-hole logs for these and other properties were run from 63 to 167 mbsf and subsequently from 200 to 623 mbsf, although density and velocity data could be obtained only to 440 mbsf because of hole collapse. Sonic velocity averages c. 2.0 km S-1 for the upper part of the hole, but there is an sharp increase to c. 3.0 km s-1 and also a slight angular unconformity, at 306 mbsf, corresponding most likely to the early/late Oligocene boundary (c. 28-30 Ma). Velocity then increases irregularly to around 3.6 km s-1 at the bottom of the hole, which is estimated to lie 120 m above the V4/V5 boundary. The higher velocities below 306 mbsf probably reflect more extensive carbonate and common pyrite cementation, in patches, nodules, bedding-parallel masses and as vein infills. Dip of the strata also increases down-hole from 3° in the upper 300 in to over 10° at the bottom. Temperature gradient is 21° k-1. Over 2 000 fractures were logged through the hole. Borehole televiewer imagery was obtained for the interval from 200 to 440 mbsf to orient the fractures for stress field analysis. Lithostratigraphical descriptions on a scale of 1:20 are presented for the full length of the core, along with core box images, as a 200 page supplement to this issue. The hole initially passed through a layer of muddy gravel to 5.5 mbsf (Lithological Sub-Unit or LSU 1.1), and then into a Quaternary diatom-bearing clast-rich diamicton to 21 mbsf (LSU 2. l), with an interval of alternating compact diamicton and loose sand, and containing a rich Pliocene foraminiferal fauna, to 27 mbsf (LSU 2.2). The unit beneath this (LSU 3.1) has similar physical properties (sonic velocity, porosity, magnetic susceptibility) and includes diamictites of similar character to those of LSU 2.1 and 2.2, but an early Miocene (c. 19 Ma) diatom assemblage at 28 mbsf (top of LSU 3.1) shows that this sub-unit is part of the older section. The strata beneath 27 mbsf, primary target for the project, extend from early Miocene to perhaps latest Eocene age, and are largely cyclic glacimarine nearshore to offshore sediments. They are described as 41 lithological sub-units and interpreted in terms of 12 recurrent lithofacies. These are 1) mudstone, 2) inter-stratified mudstone and sandstone, 3) muddy very fine to coarse sandstone, 4) well-sorted stratified fine sandstone, 5) moderately to well-sorted, medium-grained sandstone, 6) stratified diamictite, 7) massive diamictite, 8) rhythmically inter-stratified sandstone and mudstone, 9) clast-supported conglomerate, 10) matrix-supported conglomerate, 11) mudstone breccia and 12) volcaniclastic sediment. Sequence stratigraphical analysis has identified 22 unconformity-bounded depositional sequences in pre- Pliocene strata. They typically comprise a four-part architecture involving, in ascending order, 1) a sharp-based coarse-grained unit (Facies 6,7,9 or 10), 2) a fining-upward succession of sandstones (Facies 3 and 4), 3) a mudstone interval (Facies l), in some cases coarsening upward to muddy sandstones (Facies 3), and 4) a sharp-based sandstone dominated succession (mainly Facies 4). The cyclicity recorded by the strata is interpreted in terms of a glacier ice margin retreating and advancing from land to the west, and of rises and falls in sea level. Analysis of sequence periodicity awaits afirmer chronology. However, apreliminary spectral analysis of magnetic susceptibility for a deepwater mudstone within one of the sequences (from 339 to 347 mbsf) reveals ratios between hierarchical levels that are similar to those of the three Milankovitch orbital forcing periodicities. The strata contain a wide range of fossils, the most abundant being marine diatoms. These commonly form up to 5% of the sediment, though in places the core is barren (notably between 300 and 412 mbsf). Fifty samples out of 250 reviewed were studied in detail. The assemblages define ten biostratigraphical zones, some of them based on local or as yet undescribed forms. The assemblages are neritic, and largely planktonic, suggesting that the sea floor was mostly below the photic zone throughout deposition of the corcd sequence. Calcareous nannofossils, representing incursions of ocean surface waters, are much less common (72 out of 183 samples examined) and restricted to mudstone intervals a few tens of metres thick, but are important for dating. Foraminifera are also sparse (73 out of 135 samples) and represented only by calcareous benthic species. Changing assemblages indicate a shift from inshore environments in the early Oligocenc to outer shelf in the late Oligocenc, returning to inshore in the early Miocene. Marine palynomorplis yielded large numbers of well-preserved forms from most of the 116 samples examined. The new in situ assemblagc found last year in CRP-1 is extended down into the late Oligocene and a further new assemblage is found in the early Oligoccnc. Many taxa are new, and cannot us yet contribute to an improved understanding of chronology or ecology. Marine invertebrate macrofossils, mostly molluscs and serpulid tubes, are scattered throughout the core. Preservation is good in mudstones but poor in other lithologies. Climate on land is reflected in the content of terrestrial palynomorphs, which are extremely scarce down to c. 300 mbsf. Some forms are reworked, and others represent a low growing sparse tundra with at least one species of Nothofagus. Beneath this level, a significantly greater diversity and abundance suggests a milder climate and a low diversity woody vegetation in the early Oligocene, but still far short of the richness found in known Eocene strata of the region. Sedimentary facies in the oldest strata also suggest a milder climate in the oldest strata cored, with indications of substantial glacial melt-water discharges, but are typical of a coldcr climate in late Oligocene and early Miocene times. Clast analyses from diamictites reveal weak to random fabrics, suggesting either lack of ice-contact deposition or post-depositional modification, but periods when ice grounded at the drill site are inferred from thin zones of in-situ brecciated rock and soft-sediment folding. These are more common above c. 300 mbsf, perhaps reflecting more extensive glacial advances during deposition of those strata. Erosion of the adjacent Transantarctic Mountains through Jurassic basalt and dolerite-intruded Beacon strata into basement rocks beneath is recorded by petrographical studies of clast and sand grain assemblages. Core below 310 mbsf contains a dominance of fine-grained Jurassic dolerite and basalt fragments along with Beacon-derived coal debris and rounded quartz grains, whereas the strata above this level have a much higher proportion of basement derived granitoids, implying that the large areas of the adjacent mountains had been eroded to basement by the end of the early Oligocene. There is little indication of rift-related volcanism below 310 mbsf. Above this, however, basaltic and trachytic tephras are common, especially from 280 to 200 mbsf, from 150 to 46 mbsf, and in Pliocene LSU 2.2 from 21 to 27 mbsf. The largest volcanic eruptions generated layers of coarse (up to 1 cm) trachytic pumice lapilli between 97 and 114 mbsf. The thickest of these (1.2 m at 112 mbsf) may have produced an eruptive column extending tens of km into the stratosphere. A source within a few tens of km of the drill site is considered most likely. Present age estimates for the pre-Pliocene sequence are based mainly on biostratigraphy (using mainly marine diatoms and to a lesser extent calcareous nannofossils), with the age of the tephra from 112 to 114 mbsf (21.44k0.05 Ma from 84 crystals by Ar-Ar) as a key reference point. Although there are varied and well-preserved microfossil assemblages through most of the sequence (notably of diatoms and marine palynomorphs), they comprise largely taxa either known only locally or as yet undescribed. In addition, sequence stratigraphical analysis and features in the core itself indicate numerous disconformities. The present estimate from diatom assemblages is that the interval from 27 to 130 mbsf is early Miocene in age (c. 19 to 23.5 Ma), consistent with the Ar-Ar age from 112 to 114 mbsf. Diatom assemblages also indicate that the late Oligocene epoch extends from c. 130 to 307 mbsf, which is supported by late Oligocene nannofossils from 130 to 185 mbsf. Strata from 307 to 412 mbsf have no age-diagnostic assemblages, but below this early Oligocene diatoms and nannofossils have been recovered. A nannoflora at the bottom of the hole is consistent with an earliest Oligocene or latest Eocene age. Magnetostratigraphical studies based on about 1000 samples, 700 of which have so far undergone demagnetisation treatment, have provided a polarity stratigraphy of 12 pre-Pliocene magnetozones. Samples above 270 mbsf are of consistently high quality. Below this, magnetic behaviour is more variable. A preliminary age-depth plot using the Magnetic Polarity Time Scale (MPTS) and constrained by biostratigraphical data suggests that episodes of relatively rapid sedimentation took place at CRP-2 during Oligocene times (c. 100 m/My), but that more than half of the record was lost in a few major and many minor disconformities. Age estimates from Sr isotopes in shell debris and further tephra dating are expected to lead to a better comparison with the MPTS. CRP-2/2A has recorded a history of subsidence of the Victoria Land Basin margin that is similar to that found in CIROS-170 km to the south, reflecting stability in both basin and the adjacent mountains in late Cenozoic times, but with slow net accumulation in the middle Cenozoic. The climatic indicators from both drill holes show a similar correspondence, indicating polar conditions for the Quaternary but with sub-polar conditions in the early Miocene-late Oligocene and indications of warmer conditions still in the early Oligocene. Correlation between the CRP-2A core and seismic records shows that seismic units V3 and V4, both widespread in the Victoria Land Basin, represent a period of fluctuating ice margins and glacimarine sedimentation. The next drill hole, CRP-3, is expected to core deep into V5 and extend this record of climate and tectonics still further back in time.

Geographical variation in shell morphology of juvenile snails (Concholepas concholepas) along the physical-chemical gradient of the Chilean coast

Changes in phenotypic traits, such as mollusc shells, are indicative of variations in selective pressure along environmental gradients. Recently, increased sea surface temperature (SST) and ocean acidification (OA) due to increased levels of carbon dioxide in the seawater have been described as selective agents that may affect the biological processes underlying shell formation in calcifying marine organisms. The benthic snail Concholepas concholepas (Muricidae) is widely distributed along the Chilean coast, and so is naturally exposed to a strong physical-chemical latitudinal gradient. In this study, based on elliptical Fourier analysis, we assess changes in shell morphology (outlines analysis) in juvenile C. concholepas collected at northern (23°S), central (33°S) and southern (39°S) locations off the Chilean coast. Shell morphology of individuals collected in northern and central regions correspond to extreme morphotypes, which is in agreement with both the observed regional differences in the shell apex outlines, the high reclassification success of individuals (discriminant function analysis) collected in these regions, and the scaling relationship in shell weight variability among regions. However, these extreme morphotypes showed similar patterns of mineralization of calcium carbonate forms (calcite and aragonite). Geographical variability in shell shape of C. concholepas described by discriminant functions was partially explained by environmental variables (pCO2, SST). This suggests the influence of corrosive waters, such as upwelling and freshwaters penetrating into the coastal ocean, upon spatial variation in shell morphology. Changes in the proportion of calcium carbonate forms precipitated by C. concholepas across their shells and its susceptibility to corrosive coastal waters are discussed.

Análisis y clasificación de maderas mediante técnicas no invasivas de baja energía

El estudio de materiales, especialmente biológicos, por medios no destructivos está adquiriendo una importancia creciente tanto en las aplicaciones científicas como industriales. Las ventajas económicas de los métodos no destructivos son múltiples. Existen numerosos procedimientos físicos capaces de extraer información detallada de las superficie de la madera con escaso o nulo tratamiento previo y mínima intrusión en el material. Entre los diversos métodos destacan las técnicas ópticas y las acústicas por su gran versatilidad, relativa sencillez y bajo coste. Esta tesis pretende establecer desde la aplicación de principios simples de física, de medición directa y superficial, a través del desarrollo de los algoritmos de decisión mas adecuados basados en la estadística, unas soluciones tecnológicas simples y en esencia, de coste mínimo, para su posible aplicación en la determinación de la especie y los defectos superficiales de la madera de cada muestra tratando, en la medida de lo posible, no alterar su geometría de trabajo. Los análisis desarrollados han sido los tres siguientes: El primer método óptico utiliza las propiedades de la luz dispersada por la superficie de la madera cuando es iluminada por un laser difuso. Esta dispersión produce un moteado luminoso (speckle) cuyas propiedades estadísticas permiten extraer propiedades muy precisas de la estructura tanto microscópica como macroscópica de la madera. El análisis de las propiedades espectrales de la luz laser dispersada genera ciertos patrones mas o menos regulares relacionados con la estructura anatómica, composición, procesado y textura superficial de la madera bajo estudio que ponen de manifiesto características del material o de la calidad de los procesos a los que ha sido sometido. El uso de este tipo de láseres implica también la posibilidad de realizar monitorizaciones de procesos industriales en tiempo real y a distancia sin interferir con otros sensores. La segunda técnica óptica que emplearemos hace uso del estudio estadístico y matemático de las propiedades de las imágenes digitales obtenidas de la superficie de la madera a través de un sistema de scanner de alta resolución. Después de aislar los detalles mas relevantes de las imágenes, diversos algoritmos de clasificacion automatica se encargan de generar bases de datos con las diversas especies de maderas a las que pertenecían las imágenes, junto con los márgenes de error de tales clasificaciones. Una parte fundamental de las herramientas de clasificacion se basa en el estudio preciso de las bandas de color de las diversas maderas. Finalmente, numerosas técnicas acústicas, tales como el análisis de pulsos por impacto acústico, permiten complementar y afinar los resultados obtenidos con los métodos ópticos descritos, identificando estructuras superficiales y profundas en la madera así como patologías o deformaciones, aspectos de especial utilidad en usos de la madera en estructuras. La utilidad de estas técnicas esta mas que demostrada en el campo industrial aun cuando su aplicación carece de la suficiente expansión debido a sus altos costes y falta de normalización de los procesos, lo cual hace que cada análisis no sea comparable con su teórico equivalente de mercado. En la actualidad gran parte de los esfuerzos de investigación tienden a dar por supuesto que la diferenciación entre especies es un mecanismo de reconocimiento propio del ser humano y concentran las tecnologías en la definición de parámetros físicos (módulos de elasticidad, conductividad eléctrica o acústica, etc.), utilizando aparatos muy costosos y en muchos casos complejos en su aplicación de campo. Abstract The study of materials, especially the biological ones, by non-destructive techniques is becoming increasingly important in both scientific and industrial applications. The economic advantages of non-destructive methods are multiple and clear due to the related costs and resources necessaries. There are many physical processes capable of extracting detailed information on the wood surface with little or no previous treatment and minimal intrusion into the material. Among the various methods stand out acoustic and optical techniques for their great versatility, relative simplicity and low cost. This thesis aims to establish from the application of simple principles of physics, surface direct measurement and through the development of the more appropriate decision algorithms based on statistics, a simple technological solutions with the minimum cost for possible application in determining the species and the wood surface defects of each sample. Looking for a reasonable accuracy without altering their work-location or properties is the main objetive. There are three different work lines: Empirical characterization of wood surfaces by means of iterative autocorrelation of laser speckle patterns: A simple and inexpensive method for the qualitative characterization of wood surfaces is presented. it is based on the iterative autocorrelation of laser speckle patterns produced by diffuse laser illumination of the wood surfaces. The method exploits the high spatial frequency content of speckle images. A similar approach with raw conventional photographs taken with ordinary light would be very difficult. A few iterations of the algorithm are necessary, typically three or four, in order to visualize the most important periodic features of the surface. The processed patterns help in the study of surface parameters, to design new scattering models and to classify the wood species. Fractal-based image enhancement techniques inspired by differential interference contrast microscopy: Differential interference contrast microscopy is a very powerful optical technique for microscopic imaging. Inspired by the physics of this type of microscope, we have developed a series of image processing algorithms aimed at the magnification, noise reduction, contrast enhancement and tissue analysis of biological samples. These algorithms use fractal convolution schemes which provide fast and accurate results with a performance comparable to the best present image enhancement algorithms. These techniques can be used as post processing tools for advanced microscopy or as a means to improve the performance of less expensive visualization instruments. Several examples of the use of these algorithms to visualize microscopic images of raw pine wood samples with a simple desktop scanner are provided. Wood species identification using stress-wave analysis in the audible range: Stress-wave analysis is a powerful and flexible technique to study mechanical properties of many materials. We present a simple technique to obtain information about the species of wood samples using stress-wave sounds in the audible range generated by collision with a small pendulum. Stress-wave analysis has been used for flaw detection and quality control for decades, but its use for material identification and classification is less cited in the literature. Accurate wood species identification is a time consuming task for highly trained human experts. For this reason, the development of cost effective techniques for automatic wood classification is a desirable goal. Our proposed approach is fully non-invasive and non-destructive, reducing significantly the cost and complexity of the identification and classification process.

Gonçalo Byrne. Geografie dell'abitare

Oggetto centrale della presente ricerca è il rapporto che, attraverso il progetto, Byrne stabilisce di volta in volta con il territorio, identificando le origini di un atteggiamento di tipo geografico in una serie di esperienze e di sperimentazioni che maturano all’interno della cultura architettonica portoghese. La riflessione teorica e la pratica sono per Byrne strettamente legati nella definizione di una metodologia progettuale. Da questo punto di vista è determinante il suo interesse per le teorie sulla razionalizzazione delle metodologie del progetto sviluppate negli anni Sessanta in Inghilterra. L’architettura come strumento di conoscenza ha origine da un processo di analisi e di interpretazione che passa attraverso una lettura complessiva del territorio. Questo processo vede l’impiego di strumenti specifici come: il disegno, l’ordine dato dalla geometria, l’impiego di spazi matrice e la rispondenza a un programma preciso. La presente ricerca si concentra sul tema della residenza e propone di individuare una linea di continuità che, ben al di là dei caratteri linguistici esplorati attraverso ciascuno dei progetti oggetto di analisi, accompagni la riflessione attraverso cui Gonçalo Byrne si confronta con la geografia. Tali progetti sono indagati nella loro configurazione spaziale, concentrandosi nell’individuazione di soluzioni ricorrenti derivanti dalla relazione tra architettura ed elementi condizionanti locali, che trovano espressione in una serie di temi (frammentazione, imposizione, mimesi, innesto) costantemente presenti e indagati dall’autore attraverso il confronto con la ricerca progettuale, condotta negli stessi anni sia in ambito portoghese che europeo. Paradigmatici, a questo proposito, sono i progetti per Chelas (1972) e per Casal das Figueiras (1975), assunti come elementi di confronto e di verifica degli strumenti che l’architetto utilizza per l’interpretazione del luogo. La lettura e l’analisi del progetto mirano ad approfondire le relazioni fra architettura e geografia come elementi di originalità nell’opera di Byrne, individuandone le influenze socio-culturali e i riferimenti progettuali.

Effect of bioglass additions on the sintering of Y-TZP bioceramics

The objective of this work was to evaluate the influence of bioglass additions on the sintering and mechanical properties of yttria-stabilized zirconia ceramics, Y-TZP Samples containing different bioglass additions, varying between 0 and 30 wt.%, were cold uniaxial pressed at 80 MPa and sintered in air at 1200 degrees C or 1300 degrees C for 120 min. Sintered samples were characterized by X-ray Diffractometry and Scanning Electron Microscopy. Hardness and fracture toughness were determined using Vickers indentation method. As a preliminary biological evaluation, in vitro cytotoxicity tests by Neutral Red Uptake method (using mouse connective tissue cells, NCTC clone L929 from ATCC bank) were realized to determine the cytotoxicity level of ZrO(2)-bioglass ceramics. The increasing of bioglass amount leads to the decreasing of relative density due to martensitic (tetragonal-monoclinic) transformation during cooling of the sintered samples. Y-TZP samples sintered at 1300 degrees C containing 5 wt.% of bioglass presented the best results. with high relative density, hardness and fracture toughness of 11.3 GPa and 6.1 MPa m(1/2), respectively. Furthermore, the un-cytotoxic behavior was observed in all sintering conditions and bioglass amounts used in this study. (C) 2009 Elsevier B.V. All rights reserved.

Toughened ZrO2 ceramics sintered with a La2O3-rich glass as additive

In this study, the influence of the glass addition and sintering parameters on the densification and mechanical properties of tetragonal zirconia polycrystals (3Y-TZP) ceramics were evaluated. High-purity tetragonal ZrO2 powder and La2O3-rich glass were used as starting powders. Two compositions based on ZrO2 and containing 5wt.% and 10wt.% of La2O3-rich glass were studied in this work. The starting powders were mixed/milled by planetary milling, dried at 90 degrees C for 24 h, sieved through a 60 mesh screen and uniaxially cold pressed under 80 MPa. The samples were sintered in air at 1200 degrees C, 1300 degrees C, 1400 degrees C for 60 min and at 1450 degrees C for 120 min, with heating and cooling rates of 10 degrees C/min. Sintered samples were characterized by relative density, X-ray diffraction (XRD) and scanningelectron microscopy (SEM). Hardness and fracture toughness were obtained by Vickers indentation method. Dense sintered samples were obtained for all conditions. Furthermore, only tetragonal-ZrO2 was identified as crystalline phase in sintered samples, independently of the conditions studied. Samples sintered at 1300 degrees C for 60 min presented the optimal mechanical properties with hardness and fracture toughness values near to 12 GPa and 8.5 MPa m(1/2) respectively. (c) 2007 Elsevier B.V, All rights reserved.