Fotoassociação caótica no oscilador de Morse

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Chaos control and sensitivity analysis of a double pendulum arm excited by an RLC circuit based nonlinear shaker

In this paper the dynamical interactions of a double pendulum arm and an electromechanical shaker is investigated. The double pendulum is a three degree of freedom system coupled to an RLC circuit based nonlinear shaker through a magnetic field, and the capacitor voltage is a nonlinear function of the instantaneous electric charge. Numerical simulations show the existence of chaotic behavior for some regions in the parameter space and this behaviour is characterized by power spectral density and Lyapunov exponents. The bifurcation diagram is constructed to explore the qualitative behaviour of the system. This kind of electromechanical system is frequently found in robotic systems, and in order to suppress the chaotic motion, the State-Dependent Riccati Equation (SDRE) control and the Nonlinear Saturation control (NSC) techniques are analyzed. The robustness of these two controllers is tested by a sensitivity analysis to parametric uncertainties.

Oscilador harmônico unidimensional via transformada unilateral de Fourier e mapeamento do potencial de morse unidimensional nos potenciais pseudo-harmônico e de kratzer tridimensionais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Oscilador harmônico unidimensional via transformada unilateral de Fourier e mapeamento do potencial de morse unidimensional nos potenciais pseudo-harmônico e de kratzer tridimensionais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Diseño de un oscilador controlado por tensión (VCO) en tecnología SiGe 0.35 µm para el estándar DVB-H

Presentación del Proyecto Fin de Carrera titulado "DISEÑO DE UN OSCILADOR CONTROLADO POR TENSIÓN (VCO) EN TECNOLOGÍA SiGe 0.35 µm PARA EL ESTÁNDAR DVB-H"

The impact of red light cameras on safety in Arizona

Red light cameras (RLCs) have been used in a number of US cities to yield a demonstrable reduction in red light violations; however, evaluating their impact on safety (crashes) has been relatively more difficult. Accurately estimating the safety impacts of RLCs is challenging for several reasons. First, many safety related factors are uncontrolled and/or confounded during the periods of observation. Second, “spillover” effects caused by drivers reacting to non-RLC equipped intersections and approaches can make the selection of comparison sites difficult. Third, sites selected for RLC installation may not be selected randomly, and as a result may suffer from the regression to the mean bias. Finally, crash severity and resulting costs need to be considered in order to fully understand the safety impacts of RLCs. Recognizing these challenges, a study was conducted to estimate the safety impacts of RLCs on traffic crashes at signalized intersections in the cities of Phoenix and Scottsdale, Arizona. Twenty-four RLC equipped intersections in both cities are examined in detail and conclusions are drawn. Four different evaluation methodologies were employed to cope with the technical challenges described in this paper and to assess the sensitivity of results based on analytical assumptions. The evaluation results indicated that both Phoenix and Scottsdale are operating cost-effective installations of RLCs: however, the variability in RLC effectiveness within jurisdictions is larger in Phoenix. Consistent with findings in other regions, angle and left-turn crashes are reduced in general, while rear-end crashes tend to increase as a result of RLCs.

Effectiveness of red light cameras on the right-angle crash involvement of motorcycles

Red light cameras (RLC) have been used to reduce right-angle collisions at signalized intersections. However, the effect of RLCs on motorcycle crashes has not been well investigated. The objective of this study is to evaluate the effectiveness of RLCs on motorcycle safety in Singapore. This is done by comparing their exposure, proneness of at-fault right-angle crashes as well as the resulting right-angle collisions at RLC with those at non-RLC sites. Estimating the crash vulnerability from not-at-fault crash involvements, the study shows that with a RLC, the relative crash vulnerability or crash-involved exposure of motorcycles at right-angle crashes is reduced. Furthermore, field investigation of motorcycle maneuvers reveal that at non-RLC arms, motorcyclists usually queue beyond the stop-line, facilitating an earlier discharge and hence become more exposed to the conflicting stream. However at arms with a RLC, motorcyclists are more restrained to avoid activating the RLC and hence become less exposed to conflicting traffic during the initial period of the green. The study also shows that in right-angle collisions, the proneness of at-fault crashes of motorcycles is lowest among all vehicle types. Hence motorcycles are more likely to be victims than the responsible parties in right-angle crashes. RLCs have also been found to be very effective in reducing at-fault crash involvements of other vehicle types which may implicate exposed motorcycles in the conflicting stream. Taking all these into account, the presence of RLCs should significantly reduce the vulnerability of motorcycles at signalized intersections.

A high frequency current source converter with adjustable magnitude to drive high power piezoelectric transducers

A general electrical model of a piezoelectric transducer for ultrasound applications consists of a capacitor in parallel with RLC legs. A high power voltage source converter can however generate significant voltage stress across the transducer that creates high leakage currents. One solution is to reduce the voltage stress across the piezoelectric transducer by using an LC filter, however a main drawback is changing the piezoelectric resonant frequency and its characteristics. Thereby it reduces the efficiency of energy conversion through the transducer. This paper proposes that a high frequency current source converter is a suitable topology to drive high power piezoelectric transducers efficiently.

Improving ultrasound excitation systems using a flexible power supply with adjustable voltage and frequency to drive piezoelectric transducers

The ability of a piezoelectric transducer in energy conversion is rapidly expanding in several applications. Some of the industrial applications for which a high power ultrasound transducer can be used are surface cleaning, water treatment, plastic welding and food sterilization. Also, a high power ultrasound transducer plays a great role in biomedical applications such as diagnostic and therapeutic applications. An ultrasound transducer is usually applied to convert electrical energy to mechanical energy and vice versa. In some high power ultrasound system, ultrasound transducers are applied as a transmitter, as a receiver or both. As a transmitter, it converts electrical energy to mechanical energy while a receiver converts mechanical energy to electrical energy as a sensor for control system. Once a piezoelectric transducer is excited by electrical signal, piezoelectric material starts to vibrate and generates ultrasound waves. A portion of the ultrasound waves which passes through the medium will be sensed by the receiver and converted to electrical energy. To drive an ultrasound transducer, an excitation signal should be properly designed otherwise undesired signal (low quality) can deteriorate the performance of the transducer (energy conversion) and increase power consumption in the system. For instance, some portion of generated power may be delivered in unwanted frequency which is not acceptable for some applications especially for biomedical applications. To achieve better performance of the transducer, along with the quality of the excitation signal, the characteristics of the high power ultrasound transducer should be taken into consideration as well. In this regard, several simulation and experimental tests are carried out in this research to model high power ultrasound transducers and systems. During these experiments, high power ultrasound transducers are excited by several excitation signals with different amplitudes and frequencies, using a network analyser, a signal generator, a high power amplifier and a multilevel converter. Also, to analyse the behaviour of the ultrasound system, the voltage ratio of the system is measured in different tests. The voltage across transmitter is measured as an input voltage then divided by the output voltage which is measured across receiver. The results of the transducer characteristics and the ultrasound system behaviour are discussed in chapter 4 and 5 of this thesis. Each piezoelectric transducer has several resonance frequencies in which its impedance has lower magnitude as compared to non-resonance frequencies. Among these resonance frequencies, just at one of those frequencies, the magnitude of the impedance is minimum. This resonance frequency is known as the main resonance frequency of the transducer. To attain higher efficiency and deliver more power to the ultrasound system, the transducer is usually excited at the main resonance frequency. Therefore, it is important to find out this frequency and other resonance frequencies. Hereof, a frequency detection method is proposed in this research which is discussed in chapter 2. An extended electrical model of the ultrasound transducer with multiple resonance frequencies consists of several RLC legs in parallel with a capacitor. Each RLC leg represents one of the resonance frequencies of the ultrasound transducer. At resonance frequency the inductor reactance and capacitor reactance cancel out each other and the resistor of this leg represents power conversion of the system at that frequency. This concept is shown in simulation and test results presented in chapter 4. To excite a high power ultrasound transducer, a high power signal is required. Multilevel converters are usually applied to generate a high power signal but the drawback of this signal is low quality in comparison with a sinusoidal signal. In some applications like ultrasound, it is extensively important to generate a high quality signal. Several control and modulation techniques are introduced in different papers to control the output voltage of the multilevel converters. One of those techniques is harmonic elimination technique. In this technique, switching angles are chosen in such way to reduce harmonic contents in the output side. It is undeniable that increasing the number of the switching angles results in more harmonic reduction. But to have more switching angles, more output voltage levels are required which increase the number of components and cost of the converter. To improve the quality of the output voltage signal with no more components, a new harmonic elimination technique is proposed in this research. Based on this new technique, more variables (DC voltage levels and switching angles) are chosen to eliminate more low order harmonics compared to conventional harmonic elimination techniques. In conventional harmonic elimination method, DC voltage levels are same and only switching angles are calculated to eliminate harmonics. Therefore, the number of eliminated harmonic is limited by the number of switching cycles. In the proposed modulation technique, the switching angles and the DC voltage levels are calculated off-line to eliminate more harmonics. Therefore, the DC voltage levels are not equal and should be regulated. To achieve this aim, a DC/DC converter is applied to adjust the DC link voltages with several capacitors. The effect of the new harmonic elimination technique on the output quality of several single phase multilevel converters is explained in chapter 3 and 6 of this thesis. According to the electrical model of high power ultrasound transducer, this device can be modelled as parallel combinations of RLC legs with a main capacitor. The impedance diagram of the transducer in frequency domain shows it has capacitive characteristics in almost all frequencies. Therefore, using a voltage source converter to drive a high power ultrasound transducer can create significant leakage current through the transducer. It happens due to significant voltage stress (dv/dt) across the transducer. To remedy this problem, LC filters are applied in some applications. For some applications such as ultrasound, using a LC filter can deteriorate the performance of the transducer by changing its characteristics and displacing the resonance frequency of the transducer. For such a case a current source converter could be a suitable choice to overcome this problem. In this regard, a current source converter is implemented and applied to excite the high power ultrasound transducer. To control the output current and voltage, a hysteresis control and unipolar modulation are used respectively. The results of this test are explained in chapter 7.

Report on Red Light Camera Program: Operation from July 1988 to December 1989

EXECUTIVE SUMMARY (excerpts) The red light camera (RLC) program commenced in July 1988, with five cameras operating at 15 sites in metropolitan Adelaide. This report deals with the first eighteen months of operation, to December 1989. A number of recommendations have been made… PROGRAM EVALUATION … In 1989 dollars, the program was estimated to have achieved an accident reduction benefit of $1.4m in the first 12 months of operation, which is almost twice the benefit expected using the assumptions made when selecting the sites. (There are 8 recommendations, mostly specific to the particular program characteristics)

An Inexpensive Digital Network Analyzer

Frequency response analysis is critical in understanding the steady and transient state behavior of any electrical network. Network analyzeror frequency response analyzer is used to determine the frequency response of an electrical network. This paper deals with the design of an inexpensive digitally controlled Network Analyzer. The frequency range of the network analyzer is from 10Hz to 50kHz (suitable range for system studies on most power electronics apparatus). It is composed of a microcontroller (as central processing unit) and a personal computer (as analyzer and display). The communication between the microcontroller and personal computer is established through one of the USB ports. The testing and evaluation of the analyzer is done with RC, RLC and multi-resonant circuits. The design steps, basis of analysis, experimental results, limitation in bandwidth and possible techniques for improvement in performances are presented.

Broad-Band Coupling of High-Q Resonant Loads

Considering the method of broad-band coupling a series resonant RLC load to a resistive source using a uniform quarter-wave transmission-line inverter, it is shown that the 3-dB bandwidth of the network insertion loss reckoned with respect to a 0-dB loss attains a maximum for a particular value of the center frequency insertion loss in the range 0-3 dB. The center frequency Ioss and the corresponding value of the maximum 3-dB bandwidth are calculated for various loads and the results graphically presented.

Detección de comunidades en redes complejas basada en la sincronización

El estudio de las redes complejas atrae cada vez más el interés de muchos investigadores por muchas razones obvias. Muchos sistemas tanto reales como tecnológicos pueden representarse como redes complejas, es decir, un conjunto de entidades en interacción de acuerdo a propiedades topológicas no triviales. La interacción entre los elementos de la red puede describir comportamientos globales tales como el tráfico en Internet, el servicio de suministro de electricidad o la evolución de los mercados. Una de las propiedades topológicas de los grafos que caracterizan estos sistemas complejos es la estructura de comunidad. La detección de comunidades tiene como objetivo la identificación de los módulos o grupos con alguna o varias propiedades en común basándose únicamente en la información codificada en la topología del grafo. La detección de comunidades es importante no sólo para caracterizar el grafo, sino que además ofrece información sobre la formación de la red así como sobre su funcionalidad. El estudio de las leyes subyacentes que gobiernan la dinámica y evolución de los sistemas complejos y la caracterización de sus grafos revela que las redes a gran escala, generalmente, se caracterizan por topologías complejas y estructuras heterogéneas. La estructura de conectividad de estas redes se manifiesta por la presencia de comunidades (clusters o grupos), es decir, conjuntos de nodos que comparten propiedades comunes o juegan roles similares en la red. Las comunidades pueden representar relaciones de amistad en las redes sociales, páginas web con una temática similar, o rutas bioquímicas en las redes metabólicas. Formalmente, una red es un grafo compuesto por un gran número de nodos altamente interconectados donde una comunidad se resalta por la presencia de un gran número de aristas conectando nodos dentro de grupos individuales, pero con baja concentración de aristas entre estos grupos. El mejor modo para establecer la estructura de comunidad de una red compleja es un problema todavía sin resolver. Durante los últimos años, se han propuesto muchos algoritmos que persiguen extraer la partición óptima de una red en comunidades. El clustering espectral, los algoritmos de particionamiento de grafos, los métodos basados en la modularidad o los algoritmos basados en la sincronización son sólo algunos de estos algoritmos de extracción de comunidades. Los algoritmos dinámicos basados en la sincronización han sido estudiados por varios autores, y han demostrado que la monitorización del proceso dinámico de la sincronización permite revelar las diferentes escalas topologicas presentes en una red compleja. Muchos de estos algoritmos se basan en el modelo Kuramoto o en algunas de sus variantes como el modelo de opinión, donde cada oscilador aislado es modelado en un espacio unidimensional. El objetivo principal del presente proyecto es la implementación de un algoritmo de detección de comunidades basado en la sincronización de osciladores acoplados. Cada oscilador ha sido modelado mediante el sistema dinámico de Rossler, un sistema de ecuaciones diferenciales definido en un espacio tridimensional.

Análise de desempenho do protocolo TCP em Redes LTE.

O crescimento dos serviços de banda-larga em redes de comunicações móveis tem provocado uma demanda por dados cada vez mais rápidos e de qualidade. A tecnologia de redes móveis chamada LTE (Long Term Evolution) ou quarta geração (4G) surgiu com o objetivo de atender esta demanda por acesso sem fio a serviços, como acesso à Internet, jogos online, VoIP e vídeo conferência. O LTE faz parte das especificações do 3GPP releases 8 e 9, operando numa rede totalmente IP, provendo taxas de transmissão superiores a 100 Mbps (DL), 50 Mbps (UL), baixa latência (10 ms) e compatibilidade com as versões anteriores de redes móveis, 2G (GSM/EDGE) e 3G (UMTS/HSPA). O protocolo TCP desenvolvido para operar em redes cabeadas, apresenta baixo desempenho sobre canais sem fio, como redes móveis celulares, devido principalmente às características de desvanecimento seletivo, sombreamento e às altas taxas de erros provenientes da interface aérea. Como todas as perdas são interpretadas como causadas por congestionamento, o desempenho do protocolo é ruim. O objetivo desta dissertação é avaliar o desempenho de vários tipos de protocolo TCP através de simulações, sob a influência de interferência nos canais entre o terminal móvel (UE User Equipment) e um servidor remoto. Para isto utilizou-se o software NS3 (Network Simulator versão 3) e os protocolos TCP Westwood Plus, New Reno, Reno e Tahoe. Os resultados obtidos nos testes mostram que o protocolo TCP Westwood Plus possui um desempenho melhor que os outros. Os protocolos TCP New Reno e Reno tiveram desempenho muito semelhante devido ao modelo de interferência utilizada ter uma distribuição uniforme e, com isso, a possibilidade de perdas de bits consecutivos é baixa em uma mesma janela de transmissão. O TCP Tahoe, como era de se esperar, apresentou o pior desempenho dentre todos, pois o mesmo não possui o mecanismo de fast recovery e sua janela de congestionamento volta sempre para um segmento após o timeout. Observou-se ainda que o atraso tem grande importância no desempenho dos protocolos TCP, mas até do que a largura de banda dos links de acesso e de backbone, uma vez que, no cenário testado, o gargalo estava presente na interface aérea. As simulações com erros na interface aérea, introduzido com o script de fading (desvanecimento) do NS3, mostraram que o modo RLC AM (com reconhecimento) tem um desempenho melhor para aplicações de transferência de arquivos em ambientes ruidosos do que o modo RLC UM sem reconhecimento.