Damping of Vertically Excited Surface Wave in Weakly Viscous Fluid

In a vertically oscillating circular cylindrical container, singular perturbation theory of two-time scale expansions is developed in weakly viscous fluids to investigate the motion of single free surface standing wave by linearizing the Navier-Stokes equation. The fluid field is divided into an outer potential flow region and an inner boundary layer region. The solutions of both two regions are obtained and a linear amplitude equation incorporating damping term and external excitation is derived. The condition to appear stable surface wave is obtained and the critical curve is determined. In addition, an analytical expression of damping coefficient is determined. Finally, the dispersion relation, which has been derived from the inviscid fluid approximation, is modified by adding linear damping. It is found that the modified results are reasonably closer to experimental results than former theory. Result shows that when forcing frequency is low, the viscosity of the fluid is prominent for the mode selection. However, when forcing frequency is high, the surface tension of the fluid is prominent.

Surface waves in a vertically excited circular cylindrical container

The nonlinear free surface amplitude equation, which has been derived from the inviscid fluid by solving the potential equation of water waves with a singular perturbation theory in a vertically oscillating rigid circular cylinder, is investigated successively in the fourth-order Runge-Kutta approach with an equivalent time-step. Computational results include the evolution of the amplitude with time, the characteristics of phase plane determined by the real and imaginary parts of the amplitude, the single-mode selection rules of the surface waves in different forced frequencies, contours of free surface displacement and corresponding three-dimensional evolution of surface waves, etc. In addition, the comparison of the surface wave modes is made between theoretical calculations and experimental measurements, and the results are reasonable although there are some differences in the forced frequency.

Vertically forced surface wave in weakly viscous fluids bounded in a circular cylindrical vessel

Two-time scale perturbation expansions were developed in weakly viscous fluids to investigate surface wave motions by linearizing the Navier-Stokes equation in a circular cylindrical vessel which is subject to a vertical oscillation. The fluid field was divided into an outer potential flow region and an inner boundary layer region. A linear amplitude equation of slowly varying complex amplitude, which incorporates a damping term and external excitation, was derived for the weakly viscid fluids. The condition for the appearance of stable surface waves was obtained and the critical curve was determined. In addition, an analytical expression for the damping coefficient was determined and the relationship between damping and other related parameters (such as viscosity, forced amplitude, forced frequency and the depth of fluid, etc.) was presented. Finally, the influence both of the surface tension and the weak viscosity on the mode formation was described by comparing theoretical and experimental results. The results show that when the forcing frequency is low, the viscosity of the fluid is prominent for the mode selection. However, when the forcing frequency is high, the surface tension of the fluid is prominent.

大模场面积光纤激光器拉锥法模式选择

大模场面积(LMA)光纤激光器的光束质量通常比单模光纤激光器的光束质量差。采用光纤拉锥的方法进行模式选择,从而提高大模场直径光纤激光器的光束质量。拉锥区距光纤激光器的输出端约5 mm,纤芯最小为9 μm,约为未拉锥部分纤芯直径26 μm的1/3。实验研究表明,在拉锥后,光纤激光器的光束质量因子M2由3.50减小为1.81,相应的斜率效率由63.6%减小为51.1%。虽然拉锥后最大输出功率减少了约19.8%,但其亮度增大为拉锥前的3倍。

WG-like modes selectivity in a square cavity with posts

We investigate the characteristics of Whispering-Gallery(WG)-like modes in a square cavity with posts by employing the two-dimentional (2D) finite-difference time-domain (FDTD) technique combined with the effective index method. The results indicate that the posts can result in mode selection in the WG-like modes. The WG-like modes with odd mode numbers are not much sensitive to the sizes of the posts. However, the quality factor (i.e. Q-factor) of the WG-like modes with even mode numbers decreases sharply with the increasing size of the posts. The decreasing Q-factor is attributed to mode leakage and scattering loss due to the presence of the post. The mode selection increases with the mode spacing of square cavity twice in an optimized strucure.

Analysis of semiconductor microlasers with an equilateral triangle resonator by rate equations

Semiconductor microlasers with an equilateral triangle resonator (ETR) are analyzed by rate equations with the mode lifetimes calculated by the finite-difference time-domain technique and the Pade approximation. A gain spectrum based on the relation of the gain spectrum and the spontaneous emission spectrum is proposed for considering the mode selection in a wide wavelength span. For an ETR microlaser with the side length of about 5 mum, we find that single fundamental mode operation at about 1.55 mum can be obtained as the side length increases from 4.75 to 5.05 mum. The corresponding wavelength tuning range is 93 nm, and the threshold current is about 0.1 to 0.4 mA.

Analysis of output coupling efficiencies for directional emission triangle and square microlasers

Output coupling efficiencies are analyzed for triangular and square microlasers connected with an output waveguide by FDTD simulation. The results show that square resonator with an output waveguide connected to the midpoint of one side can have high output coupling efficiency and a good mode selection.

Diffusive random laser modes under a spatiotemporal scope

At present the prediction and characterization of the emission output of a diffusive random laser remains a challenge, despite the variety of investigated materials and theoretical interpretations given up to now. Here, a new mode selection method, based on spatial filtering and ultrafast detection, which allows to separate individual lasing modes and follow their temporal evolution is presented. In particular, the work explores the random laser behavior of a ground powder of an organic-inorganic hybrid compound based on Rhodamine B incorporated into a di-ureasil host. The experimental approach gives direct access to the mode structure and dynamics, shows clear modal relaxation oscillations, and illustrates the lasing modes stochastic behavior of this diffusive scattering system. The effect of the excitation energy on its modal density is also investigated. Finally, imaging measurements reveal the dominant role of diffusion over amplification processes in this kind of unconventional lasers. (C) 2015 Optical Society of America

Model reduction techniques in flexible multibody dynamics with application to engine cranktrain simulation

The development of a multibody model of a motorbike engine cranktrain is presented in this work, with an emphasis on flexible component model reduction. A modelling methodology based upon the adoption of non-ideal joints at interface locations, and the inclusion of component flexibility, is developed: both are necessary tasks if one wants to capture dynamic effects which arise in lightweight, high-speed applications. With regard to the first topic, both a ball bearing model and a journal bearing model are implemented, in order to properly capture the dynamic effects of the main connections in the system: angular contact ball bearings are modelled according to a five-DOF nonlinear scheme in order to grasp the crankshaft main bearings behaviour, while an impedance-based hydrodynamic bearing model is implemented providing an enhanced operation prediction at the conrod big end locations. Concerning the second matter, flexible models of the crankshaft and the connecting rod are produced. The well-established Craig-Bampton reduction technique is adopted as a general framework to obtain reduced model representations which are suitable for the subsequent multibody analyses. A particular component mode selection procedure is implemented, based on the concept of Effective Interface Mass, allowing an assessment of the accuracy of the reduced models prior to the nonlinear simulation phase. In addition, a procedure to alleviate the effects of modal truncation, based on the Modal Truncation Augmentation approach, is developed. In order to assess the performances of the proposed modal reduction schemes, numerical tests are performed onto the crankshaft and the conrod models in both frequency and modal domains. A multibody model of the cranktrain is eventually assembled and simulated using a commercial software. Numerical results are presented, demonstrating the effectiveness of the implemented flexible model reduction techniques. The advantages over the conventional frequency-based truncation approach are discussed.

Internationalization of small and medium sized UK manufacturing enterprises:technology and knowledge transfer perspective

This dissertation examines internationalisation of small and medium sized enterprises. There has been a journey to achieve this. The research has started as an action research as Teaching Company Scheme Associate. This has been done in two research cycles, which investigated factors for successful internationalisation of a small and medium sized UK manufacturing enterprise. This has revealed that successful internationalisation requires good technology and knowledge transfer to the new operations. The action research is followed by a survey that has been conducted within UK manufacturing companies. The data collected was analysed under three models: entry mode selection, role of factory and level of internationalisation. The first two models explain two major aspects of internationalisation decision. The last is showing what makes successful internationalising small and medium sized companies. These models provided several important results. The small and medium sized enterprise internationalisation is harder to achieve because most of these organisations do not have experience in technology and knowledge transfer. The success of internationalisation depends on the success of the transfer. This is achieved through employee ownership of the new knowledge. There are many factors affecting this result such as the network relationships such as trust, control and commitment and cognitive distance between two organisations. The last is a product of the difference between prior knowledge and the required level of knowledge. The entry mode and role of factory are decided through these factors while the level of internationalisation can only be explained by absorptive capacity of the recipient organisation and the technology transfer ability of the host organisation.

Procedimento para estudo da escolha modal em viagens realizadas por estudantes de instituições de ensino médio, mediado pela psicologia social

Tese (doutorado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Civil e Ambiental, 2016.

Commuting mode choice in transit oriented development: Disentangling the effects of competitive neighbourhoods, travel attitudes, and self-selection

This research identifies the commuting mode choice behaviour of 3537 adults living in different types of transit oriented development (TOD) in Brisbane by disentangling the effects of their “evil twin” transit adjacent developments (TADs), and by also controlling for residential self-selection, travel attitudes and preferences, and socio-demographic effects. A TwoStep cluster analysis was conducted to identify the natural groupings of respondents’ living environment based on six built environment indicators. The analysis resulted in five types of neighbourhoods: urban TODs, activity centre TODs, potential TODs, TADs, and traditional suburbs. HABITAT survey data were used to derive the commute mode choice behaviour of people living in these neighbourhoods. In addition, statements reflecting both respondents’ travel attitudes and living preferences were also collected as part of the survey. Factor analyses were conducted based on these statements and these derived factors were then used to control for residential self-selection. Four binary logistic regression models were estimated, one for each of the travel modes used (e.g. public transport, active transport, less sustainable transport such as the car/taxi, and other), to differentiate between the commuting behaviour of people living in the five types of neighbourhoods. The findings verify that urban TODs enhance the use of public transport and reduce car usage. No significant difference was found in the commuting behaviour between respondents living in traditional suburbs and TADs. The results confirm the hypothesis that TADs are the “evil twin” of TODs. The data indicates that TADs and the mode choices of residents in these neighbourhoods is a missed transport policy opportunity. Further policy efforts are required for a successive transition of TADs into TODs in order to realise the full benefits of these. TOD policy should also be integrated with context specific TOD design principles.

Sales restriction, quality selection and the mode of competition

A regulator imposing “sales restrictions” on firms competing in oligopolistic markets may enhance quality provision by the firms. Moreover, for most restrictions levels, the impact on quality selection is invariant to the mode of competition

Entry mode choice and market selection of born globals in developing countries: a multiple-case study of the ecuadorian software sector

O fenômeno "Born global" refere-se a empresas que consideram o mercado global como seu contexto natural e que iniciam seu processo de internacionalização muito cedo após sua criação. As teorias tradicionais como o modelo de Uppsala não conseguem explicar este processo. Portanto, outras teorias têm surgido, como a perspectiva de redes. Existem alguns estudos relacionados a esta área, principalmente realizados em países desenvolvidos com pequenos mercados e economias abertas. No entanto, poucos estudos têm sido feitos em economias em desenvolvimento. Além disso, o número de pesquisas quanto à escolha do modo de entrada e seleção de mercados das empresas “born global” é bastante limitado. Consequentemente, este estudo pretende descrever os principais fatores que influenciam a escolha do modo de entrada e seleção de mercados das empresas, de economias em desenvolvimento, nascidas globais. O foco da pesquisa é a indústria de software e um estudo de casos múltiplo foi realizado com três empresas no Equador. A metodologia incluiu entrevistas com fundadores, bem como a coleta de dados secundários. Com base na evidência empírica, verificou-se que os principais fatores que influenciam a escolha do modo de entrada são as restrições financeiras, as receitas esperadas, a velocidade de internacionalização, mercados nicho e a experiência empresarial anterior dos fundadores. Por outro lado, a seleção de mercado é influenciada por semelhanças de língua e cultura, mercados nicho e relações em rede.

The print collector; an introduction to the knowledge necessary for forming a collection of ancient prints. Containing suggestions as to the mode of commencing collector, the selection of specimens, the prices and care of prints. Also notices of the marks of proprietorship used by collectors, remarks on the ancient and modern practice of the art and a catalogue raisonné of books on engraving and prints.

Published anonymously. By Joseph Maberly.