Estimation of distances in virtual environments using size constancy

It is reported in the literature that distances from the observer are underestimated more in virtual environments (VEs) than in physical world conditions. On the other hand estimation of size in VEs is quite accurate and follows a size-constancy law when rich cues are present. This study investigates how estimation of distance in a CAVETM environment is affected by poor and rich cue conditions, subject experience, and environmental learning when the position of the objects is estimated using an experimental paradigm that exploits size constancy. A group of 18 healthy participants was asked to move a virtual sphere controlled using the wand joystick to the position where they thought a previously-displayed virtual cube (stimulus) had appeared. Real-size physical models of the virtual objects were also presented to the participants as a reference of real physical distance during the trials. An accurate estimation of distance implied that the participants assessed the relative size of sphere and cube correctly. The cube appeared at depths between 0.6 m and 3 m, measured along the depth direction of the CAVE. The task was carried out in two environments: a poor cue one with limited background cues, and a rich cue one with textured background surfaces. It was found that distances were underestimated in both poor and rich cue conditions, with greater underestimation in the poor cue environment. The analysis also indicated that factors such as subject experience and environmental learning were not influential. However, least square fitting of Stevens’ power law indicated a high degree of accuracy during the estimation of object locations. This accuracy was higher than in other studies which were not based on a size-estimation paradigm. Thus as indirect result, this study appears to show that accuracy when estimating egocentric distances may be increased using an experimental method that provides information on the relative size of the objects used.

Atividades de aquisição de dados no laboratório de física em cursos de tecnologia

No presente trabalho é proposto um conjunto de atividades de aquisição de dados para um laboratório didático de Física, no contexto de ensino tecnológico de escolas técnicas. São construídas rotinas de programação com a ferramenta Visual Basic for Applications (VBA), incorporadas em planilhas Excel, sendo a aquisição de dados através da porta de joystick da placa de som do microcomputador. As atividades propostas envolvem especialmente experimentos no campo da mecânica, no qual são investigados o sistema massa-mola, pêndulo simples e movimento de rotação de um pião. A metodologia proposta para estas atividades é embasada na teórica construtivista de Vygotsky. O material foi aplicado e avaliado em uma oficina oferecida para alunos de cursos superiores de tecnologia (Automação Industrial e Manutenção Industrial e Sistemas de Informação) do CEFET/PR, unidade sudoeste do Paraná em 2005. O produto educacional deste trabalho consiste em um texto de apoio sobre medidas físicas e erros e sobre o uso da linguagem VBA em sistemas de aquisição de dados com a placa de som do microcomputador, e rotinas incorporadas a planilhas Excel que permitem a aquisição automática dos dados trabalhados nas atividades experimentais. No texto de apoio, também são sugeridas atividades para os alunos. As planilhas Excel (incluindo as macros VBA) constam o CD-ROM anexo a este trabalho, e estão disponibilizadas na web.

Development of an active orthosis prototype for lower limbs

ARAUJO, Márcio V. ; ALSINA, Pablo J. ; MEDEIROS, Adelardo A. D. ; PEREIRA, Jonathan P.P. ; DOMINGOS, Elber C. ; ARAÚJO, Fábio M.U. ; SILVA, Jáder S. . Development of an Active Orthosis Prototype for Lower Limbs. In: INTERNATIONAL CONGRESS OF MECHANICAL ENGINEERING, 20., 2009, Gramado, RS. Proceedings… Gramado, RS: [s. n.], 2009

Investigação da relação entre conteúdo onírico e aprendizado de uma tarefa cognitiva complexa

Several lines of evidence indicate that sleep is beneficial for learning, but there is no experimental evidence yet that the content of dreams is adaptive, i.e., that dreams help the dreamer to cope with challenges of the following day. Our aim here is to investigate the role of dreams in the acquisition of a complex cognitive task. We investigated electroencephalographic recordings and dream reports of adult subjects exposed to a computer game comprising perceptual, motor, spatial, emotional and higher-level cognitive aspects (Doom). Subjects slept two nights in the sleep laboratory, a completely dark room with a comfortable bed and controlled temperature. Electroencephalographic recordings with 28 channels were continuously performed throughout the experiment to identify episodes of rapid-eye-movement (REM) sleep. Behaviors were continuously recorded in audio and video with an infrared camera. Dream reports were collected upon forced awakening from late REM sleep, and again in the morning after spontaneous awakening. On day 1, subjects were habituated to the sleep laboratory, no computer game was played, and negative controls for gamerelated dream reports were collected. On day 2, subjects played the computer game before and after sleep. Each game session lasted for an hour, and sleep for 7-9 hours. 9 different measures of performance indicated significant improve overnight. 81% of the subjects experienced intrusion of elements of the game into their dreams, including potentially adaptative strategies (insights). There was a linear correlation between performance and dream intrusion as well as for game improval and quantity of reported dreaming. In the electrophysiological analysis we mapped the subjects brain activities in different stages (SWS 1, REM 1, SWS 2, REM 2, Game 1 and Game 2), and found a modest reverberation in motor areas related to the joystick control during the sleep. When separated by gender, we found a significant difference on female subjects in the channels that indicate motor learning. Analysis of dream reports showed that the amount of gamerelated elements in dreams correlated with performance gains according to an inverted-U function analogous to the Yerkes-Dodson law that governs the relationship between arousal and learning. The results indicate that dreaming is an adaptive behavior

Projeto e concepção de um quadcopter utilizando o controle PID

The present work refers to the design, conception and development of a quadcopter based on PID controllers, a widespread microcontroller on the market was being implemented, the Arduino. Also made use of LabVIEW programming tool from National Instruments company for the quadcopter control and telemetry. For the control, LabVIEW software acquired the joystick commands, making the necessary adjustments to the perfect interpretation by microcontroller on the quadcopter and adjusts the parameters of PID controllers. For telemetry, data relating to quadcopter behavior are received, interpreted and presented in an intuitive user interface. In the first part of this graduate work presents the theoretical background on the subject, with a brief history about the quadcopters, followed by the main projects in the academic and commercial matters. Also are presented the theories of communications used in the design and PID control. Then an overview of the dynamic and mathematical model is demonstrated. Having done this, the physical and computer components required to complete the project are showed and the results are achieved consequently. Finally, a conclusion is made taking into account the results obtained. In this work will be presented the PID control of quadcopter translational movements only to roll and pitch movements

Fingerbyte: utilizando conceitos teóricos de comunicação e pesquisa de opinião para adequação de um produto

This project aims to use concepts of innovation and obsolescence in products, to analyze and test the technological product FingerByte, a blend glove and joystick that needs to be appropriate for specific audiences. For this adjustment, this project uses a qualitative opinion survey, known as focus group in order to obtain data during product testing with certain audiences. Another purpose of the paper is to serve as a guide to readers in similar situations where you wish to use focus groups to develop products that have not been put on the market. The experiment uses the knowledge of public relations, both in research and in data analysis. The main results of the research are described in this monograph, in order to demonstrate what are the possible types of data being collected, helping the reader to approach the experience of qualitative research

DESIGN AND ANALYSIS OF MULTIFUNCTIONAL ROBOT FOR NOTES

The elimination of all external incisions is an important step in reducing the invasiveness of surgical procedures. Natural Orifice Translumenal Endoscopic Surgery (NOTES) is an incision-less surgery and provides explicit benefits such as reducing patient trauma and shortening recovery time. However, technological difficulties impede the widespread utilization of the NOTES method. A novel robotic tool has been developed, which makes NOTES procedures feasible by using multiple interchangeable tool tips. The robotic tool has the capability of entering the body cavity through an orifice or a single incision using a flexible articulated positioning mechanism and once inserted is not constrained by incisions, allowing for visualization and manipulations throughout the cavity. Multiple interchangeable tool tips of the robotic device initially consist of three end effectors: a grasper, scissors, and an atraumatic Babcock clamp. The tool changer is capable of selecting and switching between the three tools depending on the surgical task using a miniature mechanism driven by micro-motors. The robotic tool is remotely controlled through a joystick and computer interface. In this thesis, the following aspects of this robotic tool will be detailed. The first-generation robot is designed as a conceptual model for implementing a novel mechanism of switching, advancing, and controlling the tool tips using two micro-motors. It is believed that this mechanism achieves a reduction in cumbersome instrument exchanges and can reduce overall procedure time and the risk of inadvertent tissue trauma during exchanges with a natural orifice approach. Also, placing actuators directly at the surgical site enables the robot to generate sufficient force to operate effectively. Mounting the multifunctional robot on the distal end of an articulating tube provides freedom from restriction on the robot kinematics and helps solve some of the difficulties otherwise faced during surgery using NOTES or related approaches. The second-generation multifunctional robot is then introduced in which the overall size is reduced and two arms provide 2 additional degrees of freedom, resulting in feasibility of insertion through the esophagus and increased dexterity. Improvements are necessary in future iterations of the multifunctional robot; however, the work presented is a proof of concept for NOTES robots capable of abdominal surgical interventions.

Analysis of aircraft load spectrum by means of flight simulator

Damage tolerance analysis is a quite new methodology based on prescribed inspections. The load spectra used to derive results of these analysis strongly influence the final defined inspections programs that for this reason must be as much as possible representative of load acting on the considered structural component and at the same time, obtained reducing both cost and time. The principal purpose of our work is in improving the actual condition developing a complete numerical Damage Tolerance analysis, able to prescribe inspection programs on typical aircraft critical components, respecting DT regulations, starting from much more specific load spectrum then those actually used today. In particular, these more specific load spectrum to design against fatigue have been obtained through an appositively derived flight simulator developed in a Matlab/Simulink environment. This dynamic model has been designed so that it can be used to simulate typical missions performing manually (joystick inputs) or completely automatic (reference trajectory need to be provided) flights. Once these flights have been simulated, model’s outputs are used to generate load spectrum that are then processed to get information (peaks, valleys) to perform statistical and/or comparison consideration with other load spectrum. However, also much more useful information (loads amplitude) have been extracted from these generated load spectrum to perform the previously mentioned predictions (Rainflow counting method is applied for this purpose). The entire developed methodology works in a complete automatic way, so that, once some specified input parameters have been introduced and different typical flights have been simulated both, manually or automatically, it is able to relate the effects of these simulated flights with the reduction of residual strength of the considered component.

Algorithms for autonomous tandem operation of a dual M113 system

In mid-July 2003, the U.S. Army Tank-Automotive & Armaments Command (TACOM) performed a series of experiments at Keweenaw Research Center (KRC), with a remote operated mine roller system. This system, named Panther Lite, consists of two M113 Armored Personnel Carriers (APC’s) connected by a Tandem Vehicle Linkage Assembly (TVLA). The system has three sets of mine rollers, two of which are connected to the front of the lead vehicle with one set trailing from the trail vehicle. Currently, the system requires two joystick controllers. One regulates the braking of the tracks, throttle, and transmission of the lead vehicle and the other controls the braking and throttle of the rear vehicle. One operator controls both joysticks, attempting to maneuver the lead vehicle along a desired path. At the same time, this operator makes compensation maneuvers to reduce lateral loads in the TVLA and to guide the rear mine rollers along the desired path. The purpose of this project is to create algorithms that would allow the slave (trail) vehicle to operate using inputs that maneuver the control (lead) vehicle. The project will be completed by first reconstructing the experimental data. Kinematic models will be generated and simulations created. The models will then be correlated with the reconstructions of the experimental data. The successful completion of this project will be a first step to eliminating the need for the second joystick.

Radialer externer Fixateur zur geschlossenen Behandlung problematischer suprakondylärer Humerusfrakturen Typ III und IV bei Kindern und Jugendlichen

Operationsziel Geschlossene, anatomische Reposition und sichere Fixation von problematischen suprakondylären Typ-III- und Typ-IV-Humerusfrakturen, die mit den herkömmlichen Operationsmethoden nur schwierig geschlossen zu behandeln sind. Indikationen Gemäß der AO-Kinderklassifikation der suprakondylären Humerusfrakturen vom Typ III und IV: Frakturen, welche nicht geschlossen mittels üblicher Repositionsmethoden reponierbar sind sowie Frakturen, die nicht mittels der üblichen, gekreuzten perkutanen Kirschner-Draht-Technik zu fixieren sind. Bei schweren Schwellungszuständen, offener Fraktur oder initial neurologischen und/oder vaskulären Problemen („pulseless pink hand“) sowie bei mehrfachverletzten Kindern, welche eine optimale Rehabilitation benötigen und die Extremität gipsfrei sein sollte. Bei Kindern mit Komorbiditäten (z. B. Anfälle, Spastizität), die eine bessere Stabilität benötigen. Kontraindikationen Prinzipiell keine Kontraindikationen Operationstechnik Im nichtreponierten Zustand unter Durchleuchtungskontrolle Einbringen einer einzelnen Schanz-Schraube in den lateralen (radialen) Aspekt des distalen Fragments, welches sich in der streng seitlichen Röntgenprojektion als „Sand-Uhr“- bzw. Kreisform des Capitulum humeri darstellt. Je nach Größe dieses distalen Fragments kann die Schanz-Schraube rein epiphysär oder metaphysär liegen. Danach in absolut streng seitlicher Projektion des distalen Humerus im Bereich des meta-diaphysären Übergangs Einbohren einer 2. Schanz-Schraube unabhängig von der Ersten, die möglichst rechtwinklig zur Längsachse des Humerus in der a.-p.-Ebene zu liegen kommen sollte, um spätere Manipulationen mittels „Joy-Stick“-Technik zu erleichtern. Sind die beiden Schanz-Schrauben mehr oder weniger in beiden Ebenen parallel, so ist die Fraktur praktisch anatomisch reponiert. Nach erreichter Reposition Feinjustierung aller Achskomponenten. Sicherung der Flexion/Extension mittels einem von radial, distal eingebrachten sog. Anti-Rotations-Kirschner-Drahts, der die Stabilität signifikant erhöht und eine Drehung des distalen Fragments um die einzelne Schanz-Schraube verhindert. Postoperative Behandlung Keine zusätzliche Gipsruhigstellung notwendig. Es sollte eine funktionelle Nachbehandlung erfolgen. Ergebnisse Gemäß unserer Langzeitstudien bewegen die meisten Kinder bereits zum Zeitpunkt der ambulanten Pin-Entfernung in der Frakturambulanz ihren Ellbogen weitgehend normal. Bei einer Follow-up-Zeit über 40 Monate hatten 30/31 Kindern eine seitengleiche Achse und Beweglichkeit.

E-Racer

The E-Racer was made for a young boy with cerebral palsy. The client cannot use his legs and control in his left arm is very limited. The client's family expressed a desire for an electric go-kart, and also for the go-kart to resemble a "normal" go-kart. To that end, the E-Racer has been outfitted with both steering wheel and joystick modes so the client can choose which control system he would like to use depending on what he is comfortable with. The E-Racer is a stock go-kart which was modified in several key ways. The electronics were drastically modified to accommodate the two controls systems. In addition, both the steering and braking systems were modified so they could be controlled electrically rather than mechanically. Finally, several modifications were made to the go-kart to improve the rider's comfort and safety.

CORRELAÇÕES ENTRE PERCEPÇÃO DA PASSAGEM DO TEMPO, ATENÇÃO DIFUSA E ANSIEDADE

O presente estudo teve como objetivo avaliar aspectos psicofisiológicos da ansiedade em particular a atenção e a percepção da passagem do tempo. Foi aplicada a escala psicométrica de ansiedade do IDATE em 180 alunos do curso de Educação Física da Universidade de São Paulo em sala de aula. Foram selecionados 15 voluntários mais ansiosos e 15 menos ansiosos foi considerado o IDATE traço por apresentar características mais constantes da ansiedade. O experimento 1 foi a tarefa de Tempo Espontâneo onde os participantes deviam bater o dedo no botão A do joystick da forma mais regular e precisa possível por um minuto. Já no experimento 2 os participantes foram orientados a responder o mais rápido possível ao surgimento do estimulo (ponto branco 0,4 grau) com uma luminância de 80 cd/m contra um fundo cinza pressionando o botão A do joystick com qualquer dedo da mão dominante (TRS). Os estímulos eram apresentados randomicamente por 82 posições diferentes na tela do computador. Após tratamento dos dados e analise estatística, o estudo de caráter geral e exploratório apresentado aqui mostra tendências, mas não correlações significativas entre as medidas. Alguns dados, no entanto, chamam a atenção e devem ser considerados no planejamento de experimentos futuros.

Development of an active orthosis prototype for lower limbs

ARAUJO, Márcio V. ; ALSINA, Pablo J. ; MEDEIROS, Adelardo A. D. ; PEREIRA, Jonathan P.P. ; DOMINGOS, Elber C. ; ARAÚJO, Fábio M.U. ; SILVA, Jáder S. . Development of an Active Orthosis Prototype for Lower Limbs. In: INTERNATIONAL CONGRESS OF MECHANICAL ENGINEERING, 20., 2009, Gramado, RS. Proceedings… Gramado, RS: [s. n.], 2009

Sillas de ruedas eléctricas. Opciones de mandos de control y cambios de postura

En una persona con movilidad reducida, el desplazamiento en una silla de ruedas con motor es equiparable a caminar, porque facilita la igualdad de acceso para: elegir y tomar decisiones, acceder a la información, participar en la educación, el empleo, el ocio y la vida familiar. Hasta hace pocos años, una persona que no podía propulsar una silla de ruedas manual y tampoco podía manejar el joystick de una silla de ruedas eléctrica, se veía obligado a que fuera otra persona quien le "llevara", o le cambiara de postura. Hoy en día las sillas de ruedas eléctricas han evolucionado tanto, que muchas personas pueden desplazarse, ponerse más erguidas, reclinarse o ponerse de pie en la silla, incluso sin el movimiento de las manos. El propósito de este documento es ofrecer asesoramiento sobre los aspectos a tener en cuenta al valorar el acceso más eficaz para controlar la silla de ruedas eléctrica y proporcionar información sobre los diferentes mandos de control y opciones de cambios de postura que hoy día están disponibles en el mercado nacional.