An analytical model for guided wave inspection optimization for prismatic structures of any cross section.

This paper presents an analytical modeling technique for the simulation of long-range ultrasonic guided waves in structures. The model may be used to predict the displacement field in a prismatic structure arising from any excitation arrangement and may therefore be used as a tool to design new inspection systems. It is computationally efficient and relatively simple to implement, yet gives accuracy similar to finite element analysis and semi-analytical finite element analysis methods. The model has many potential applications; one example is the optimization of part-circumferential arrays where access to the full circumference of the pipe is restricted. The model has been successfully validated by comparison with finite element solutions. Experimental validation has also been carried out using an array of piezoelectric transducer elements to measure the displacement field arising from a single transducer element in an 88.9-mm-diameter pipe. Good agreement has been obtained between the two models and the experimental data.

Flaw sizing in pipes using long-range guided wave testing

The absence of adequate inspection data from difficult-to-access areas on pipelines, such as cased-road crossings, makes determination of fitness for continued service and compliance with increasingly stringent regulatory requirements problematic. Screening for corrosion using long-range guided wave testing is a relatively new inspection technique. The complexity of the possible modes of vibration means the technique can be difficult to implement effectively but this also means that it has great potential for both detecting and characterizing flaws. The ability to determine flaw size would enable the direct application of standard procedures for determining fitness-for-service, such as ASME B31G, RSTRENG, or equivalent for tens of metres of pipeline from a single inspection location. This paper presents a new technique for flaw sizing using guided wave inspection data. The technique has been developed using finite element models and experimentally validated on 6'' Schedule 40 steel pipe. Some basic fitness-for-service assessments have been carried out using the measured values and the maximum allowable operating pressure was accurately determined. © 2011 American Institute of Physics.

PHOTOSIGNAL ENHANCEMENT IN AL-GAAS DIODES DUE TO SURFACE-PLASMONS AND GUIDED-WAVE MODES

Light of wavelength 632.8 nm and p-polarization is incident on a prism-air gap (varied from 0.7 to 7 mum)-Al-GaAs arrangement. Both the photosignal generated by the Schottky diode and the reflectance are measured as a function of the internal angle of incidence in the prism. There is significant, well-defined enhancement of the photosignal, up to a factor of approximately 7.5, associated with two different types of enhanced absorption modes. For air gaps <1.5 mum there is photosignal enhancement due to an enhanced absorption feature (reflectance dip) that occurs at an angle of incidence just above critical angle in the prism; this feature corresponds to the excitation of a surface plasmon polariton at the Al-air interface. For air gaps > 1 mum there are between one and ten photoresponse peaks at input angles less than the critical angle. The corresponding enhanced absorption features are due to leaky guided wave modes set up in the air gap.

Wave optics analysis by phase-shifting real-time holographic interferometry

The purpose of this work is to study the potentialities in the phase-shifting real-time holographic interferometry using photorefractive crystals as the recording medium for wave-optics analysis in optical elements and non-linear optical materials. This technique was used for obtaining quantitative measurements from the phase distributions of the wave front of lens and lens systems along the propagation direction with in situ visualization, monitoring and analysis in real time. (C) 2008 Elsevier GmbH. All rights reserved.

Damage Characterization Using Guided-Wave Linear Arrays and Image Compounding Techniques

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Combining Monte Carlo methods with coherent wave optics for the simulation of phase-sensitive X-ray imaging

Phase-sensitive X-ray imaging shows a high sensitivity towards electron density variations, making it well suited for imaging of soft tissue matter. However, there are still open questions about the details of the image formation process. Here, a framework for numerical simulations of phase-sensitive X-ray imaging is presented, which takes both particle- and wave-like properties of X-rays into consideration. A split approach is presented where we combine a Monte Carlo method (MC) based sample part with a wave optics simulation based propagation part, leading to a framework that takes both particle- and wave-like properties into account. The framework can be adapted to different phase-sensitive imaging methods and has been validated through comparisons with experiments for grating interferometry and propagation-based imaging. The validation of the framework shows that the combination of wave optics and MC has been successfully implemented and yields good agreement between measurements and simulations. This demonstrates that the physical processes relevant for developing a deeper understanding of scattering in the context of phase-sensitive imaging are modelled in a sufficiently accurate manner. The framework can be used for the simulation of phase-sensitive X-ray imaging, for instance for the simulation of grating interferometry or propagation-based imaging.

Wave optics and atomics.

Physical optics.--Physical electronics.--Atomic physics.--Nuclear physics.

Optics-Based Quantum Information and Sensing Platforms Utilizing the Nitrogen-Vacancy Center in Diamond

Thesis (Ph.D.)--University of Washington, 2016-08

溶胶-凝胶光波导环形谐振腔的挥发性有机化合物传感特性

采用溶胶-凝胶法制作波导环形谐振腔, 讨论了环形谐振腔器件的传输特性。测量了在不同物质、不同体积分数的挥发性有机化合物(VOC)蒸气气氛下器件的传输光谱的敏感性。结果表明, 谐振波长随甲醇、乙醇、丙醇等醇类化合物, 以及丙酮、甲醛等蒸气体积分数的上升而向长波方向移动, 具有高的灵敏度, 且两者基本呈线性关系。其中, 对丙醇最敏感, 灵敏度达到1.403 pm/10-6。对甲烷和二甲苯也有微弱反应, 但是其灵敏度很低。也测量了水蒸气对传输谱特性的影响。观察到传输谱衬比度对不同挥发性有机化合物物质蒸气的不同敏

溶胶-凝胶条波导Sagnac环的乙醇蒸气传感特性

采用有机/无机混合溶胶-凝胶法制作条形光波导,并将条波导接入光纤Sagnac 环中,测量了输出光功率随环境气氛中乙醇蒸气体积分数变化的特性,表明在实验研究的范围内,输出信号与乙醇蒸气体积分数呈正弦变化。根据Sagnac环结构输出特性的基本关系,反映了溶胶-凝胶条波导在乙醇蒸气气氛下产生了双折射效应。观察到双折射相移与乙醇体积分数的亚线性关系。对实验数据拟合,计算了偏振相移的线性项和二次项系数,得到所制备的条波导的双折射对乙醇体积分数的响应为Δn≈4.4×10-2。测量了信号变化的时间演变特性,典型的上升和

平面交叉型微透镜阵列的制作及成像特性研究

介绍了采用光刻离子交换工艺制作平面交叉型微透镜阵列的方法。利用积分形式的光线方程式讨论了平面交叉型微透镜的近轴光学特性，研究了微透镜的光线轨迹方程式和一些重要的近轴成像特性，利用ABCD定理得到了平面交叉型微透镜像距、焦距、像高、横向放大率和主平面位置的数学表达式，焦距的理论计算结果和实验数据吻合得很好。

掺铒磷酸盐玻璃波导放大器的特性研究

研究了掺铒磷酸盐玻璃波导放大器的特性。利用重叠因子将980nm光抽运的掺铒玻璃波导放大器四能级模型的速率-传输方程进行化简，在考虑上转换效应和放大自发发射的情况下．利用数值模拟的方法，得到了掺铒玻璃波导放大器的增益与Er^3+离子浓度、抽运功率、波导长度等参量之间的关系曲线；同时模拟出放大自发发射曲线并与实验测量结果进行比较。结果表明在考虑上转换效应和放大自发发射的情况下,理论结果和实验测量结果是一致的。同时看到，选择合适的铒离子浓度是制作掺铒玻璃波导放大器的关键；并且为了全面发挥掺铒玻璃波导放大器的性能

偏振光斯托克斯参量的高速实时测量技术

为了满足对高速变化的偏振态的测量,提出一种能够对偏振态实现高速测量的技术。阐述了利用1/4波片与起偏器测量偏振光的斯托克斯参量常规的原理和方法,根据高速测量的要求推导出了新的斯托克斯参量计算公式,并依据此公式设计了基于多通道偏振态高速测量的方案,设计了具体的方法并编写了控制与算法程序。测试表明,该系统的测量速度达到了每秒700次偏振态测量,测量速度主要由电子线路的性能决定,测得的结果稳定可靠实现了光纤传输偏振态的高速测量。

Design, Fabrication and Characterization of Passive and Active Polymer Photonic Devices

The rapid developments in fields such as fibre optic communication engineering and integrated optical electronics have expanded the interest and have increased the expectations about guided wave optics, in which optical waveguides and optical fibres play a central role. The technology of guided wave photonics now plays a role in generating information (guided-wave sensors) and processing information (spectral analysis, analog-to-digital conversion and other optical communication schemes) in addition to its original application of transmitting information (fibre optic communication). Passive and active polymer devices have generated much research interest recently because of the versatility of the fabrication techniques and the potential applications in two important areas – short distant communication network and special functionality optical devices such as amplifiers, switches and sensors. Polymer optical waveguides and fibres are often designed to have large cores with 10-1000 micrometer diameter to facilitate easy connection and splicing. Large diameter polymer optical fibres being less fragile and vastly easier to work with than glass fibres, are attractive in sensing applications. Sensors using commercial plastic optical fibres are based on ideas already used in silica glass sensors, but exploiting the flexible and cost effective nature of the plastic optical fibre for harsh environments and throw-away sensors. In the field of Photonics, considerable attention is centering on the use of polymer waveguides and fibres, as they have a great potential to create all-optical devices. By attaching organic dyes to the polymer system we can incorporate a variety of optical functions. Organic dye doped polymer waveguides and fibres are potential candidates for solid state gain media. High power and high gain optical amplification in organic dye-doped polymer waveguide amplifier is possible due to extremely large emission cross sections of dyes. Also, an extensive choice of organic dye dopants is possible resulting in amplification covering a wide range in the visible region.