Diamond-like carbon coating for optical windows

Hard, low stress diamond-like carbon films have been deposited by plasma assisted chemical vapour deposition technique, The various substrates include soft IR components like ZnS and ZnSe windows, Gaseous precursors such as propene, ethyl alcohol and acetone have been used to synthesize the films to study the nature of precursors in determining the film compatibility with the underlying component (substrate), The residual compressive stresses, the Young's modulus and the adhesion energy of the films have been estimated to be 10(10) dynes/cm(2), 10(10) N/m(2) and 1000 ergs/cm(2) respectively. To alleviate film failure, a study on the effects of additive gases such as hydrogen and the use of buffer layers such as ZrO2, has been undertaken, The diamond-like carbon films produced here are hard (5000 kg/mm(2)), specularly smooth in the wavelength region from 2.5 mu m to 20 mu m, with no microstructural features and have excellent adhesion on ZnS and ZnSe windows. The figure of merit of these films for aero-space applications has been evaluated by subjecting the film-buffer layer ZnS or ZnSe composite stack to wind, dust and rain erosion studies and by establishing the integrity of the specular IR transmittance of the stack upto 16 or 20 mu m as the case may be.

A Microtube Viscometer with a Thermostat

The viscometer presented in this paper is suit-able for measuring the viscosity of liquids in micro-litre quantities. It consists of a micro-flow experimental system with a thermostat. Using the measurements of the flow rates and pressure drops of a liquid passing through a microtube, the liquid's viscosity can be calculated from on Hagen-Poiseuille theory. After calibration, the viscometer was used to measure viscosities of deionized water and ethyl alcohol at temperatures ranging from 0 to 40 "C. For both test liquids, the relative deviation of the measured values from those quoted in the literature (obtained using other viscometers) was less than 2.6o/o. The relative uncertainty of the experimental system was reduced to +-l.8% using the relative measuring method. Due to the micro-scale of the test section, only a micro-litre quantity of liquid is needed for a test, this is a potential advantage for measurement of bio-liquid viscosities.

Microwave Resonant and Zero-Field Absorption Study of Doped Magnetite Prepared by a Co-Precipitation Method

Fe3O4 and ZnxFe3-xO4 pure and doped magnetite magnetic nanoparticles (NPs) were prepared in aqueous solution (Series A) or in a water-ethyl alcohol mixture (Series B) by the co-precipitation method. Only one ferromagnetic resonance line was observed in all cases under consideration indicating that the materials are magnetically uniform. The shortfall in the resonance fields from 3.27 kOe (for the frequency of 9.5 GHz) expected for spheres can be understood taking into account the dipolar forces, magnetoelasticity, or magnetocrystalline anisotropy. All samples show non-zero low field absorption. For Series A samples the grain size decreases with an increase of the Zn content. In this case zero field absorption does not correlate with the changes of the grain size. For Series B samples the grain size and zero field absorption behavior correlate with each other. The highest zero-field absorption corresponded to 0.2 zinc concentration in both A and B series. High zero-field absorption of Fe3O4 ferrite magnetic NPs can be interesting for biomedical applications.

Efeitos da exposição precoce ao etanol na atividade locomotora e na expressão dos genes de controle do ritmo circadiano de camundongos adolescentes em diferentes períodos do ciclo claro/escuro

A hiperatividade locomotora e as alterações nos ritmos circadianos têm sido descritas em roedores e humanos expostos ao etanol durante o desenvolvimento. Considerando que a atividade locomotora em camundongos é conhecida por variar ao longo das fases do ciclo claro escuro, é possível que o fenótipo hiperativo resultante da exposição precoce ao etanol também varie em função da hora do dia. Além disso, é possível que a hiperatividade apresentada pelos indivíduos expostos ao etanol durante o desenvolvimento esteja associada com distúrbios no sistema de controle do ritmo circadiano. Neste estudo, avaliamos estas duas possibilidades realizando uma análise circadiana da atividade locomotora e da expressão dos genes de relógio de camundongos adolescentes expostos ao etanol durante o período de surto de crescimento cerebral. Para tanto, camundongos suíços criados e mantidos em um ciclo claro/escuro de 12h (luzes acesas às 2:00h, apagadas as 14:00h) foram injetados com etanol (5g/kg ip, grupo ETOH) ou um volume equivalente de solução salina (grupo SAL) em dias alternados do segundo ao oitavo dias pós-natais. No 30 dia pós-natal, os animais foram testados em campo aberto por 15 minutos em diferentes momentos do ciclo claro/escuro: durante a fase clara entre 6:00 e 7:30h e entre12:00 e 13:30h; durante a fase escura entre 18:00 e 19:30h e entre 0:00 e 01:30h. Durante a fase escura os testes foram realizados sob iluminação com luz vermelha. Após os testes comportamentais, alguns animais foram randomicamente selecionados para as análises de imunofluorescência da expressão dos genes PER 1, 2 e 3 no núcleo supraquiasmático. Ao longo dos seis primeiros minutos, a atividade locomotora dos animais testados durante o período claro não mudou significativamente ou apresentou um leve aumento e a dos animais testados no período escuro apresentou uma marcante redução. Além disso, o grupo de animais testados entre 00:00 e 1:30h apresentou a maior atividade locomotora e o grupo dos animais testados entre 12:00 e 13:30h apresentou a menor atividade locomotora. De modo importante, a exposição neonatal ao etanol promoveu hiperatividade locomotora apenas no grupo de animais testados entre 00:00 e 1:30h. Em relação aos genes de controle do ritmo circadiano, a exposição precoce ao etanol afetou apenas a expressão do gene Per1 que foi menor entre 18:00 e 19:30h. O fato de que a expressão dos genes de controle do ritmo circadiano foi alterada no meio da fase escura e que a hiperatividade locomotora foi observada apenas no final da fase escura é compatível com a hipótese de que a hiperatividade induzida pelo etanol pode estar associada com as perturbações de controle do ritmo circadiano.

Studies on the preparation of fish protein concentrate

The paper deals with the method of preparation of an edible fish protein concentrate from cheap miscellaneous fish. The method consists in cooking the fish with 0.5% glacial acetic acid, and extracting batch—wise, using ethyl alcohol followed by an azeotropic mixture of hexane and alcohol (B. Pt. 58-68°C). The product is finally vacuum dried during which the residual solvent is also removed. The concentrate prepared by this method contains 85% protein of which 96% is pepsin digestible. The product is practically odorless and almost white in color.

A pilot plant for fish protein concentrate

This communication deals with the design aspect and functions of individual pieces of equipment of a pilot plant of fifty kg capacity for the production of fish protein concentrate (FPC) per day. Design is based on a solvent extraction process of wet pressed cake with an azeotropic mixture of hexane and ethyl alcohol. A flow sheet for the process and equipment layout has been indicated.

The genetic diversity of Acipenser stellatus populations in the Caspian Sea was studied using microsatellite technique

A total of 361 caudal fin samples were collected from adult A. stellatus specimens caught in the north Caspian Sea, including specimens from Kazakhstan (Ural River), Russia (Volga River), Azerbaijan (Kura River), specimens caught in the south Caspian Sea including specimens from Fishery Zone 1 (from Astara to Anzali), Fishery Zone 2 (from Anzali to Ramsar), Fishery Zone 3 (from Nowshahr to Babolsar), Fishery Zone 4 (from Miyankaleh to Gomishan) as well as from specimens caught in Turkmenistan (all specimens were collected during the sturgeon stock assessment survey). About 2 g of fin tissue was removed from each caudal fin sample, stored in 96% ethyl alcohol and transferred to the genetic laboratory of the International Sturgeon Research Institute. Genomic DNA was extracted using phenol-chloroform method. The quality and quantity of DNA was assessed using 1% Agarose gel electrophoresis and Polymerase Chain Reaction (PCR) was conducted on the target DNA using 15 paired microsatellite primer. PCR products were electrophoresed on polyacrylamide gels (6%) that were stained using silver nitrate. Electrophoretic patterns and DNA bands were analyzed with BioCapt software. Allele count and frequency, genetic diversity, expected heterozygosity and observed heterozygosity allele number, and the effective allele number, genetic similarity and genetic distance, FST and RST were calculated. The Hardy Wienberg Equilibrium based on X2 and Analysis of Molecular Variance (AMOVA) at 10% confidence level was calculated using the Gene Alex software. Dendrogram for genetic distances and identities were calculated using TFPGA program for any level of the hierarchy. It is evident from the results obtained that the 15 paired primers studied, polymorphism was observed in 10 pairs in 12 loci, while one locus did not produce DNA bands. Mean allele number was 13.6. Mean observed and expected heterozygosity was 0.86 and 0.642, respectively. It was also seen that specimens from all regions were not in Hardy Wienberg Equilibrium in most of the loci (P≤0.001). Highest Fst (0.063) was observed when comparing specimens from Fishery Zone 2 and Fishery Zone 4 (Nm=3.7) and lowest FST (0.028) was observed when comparing specimens from the Volga River and those from the Ural River (8.7). Significant differences (P<0.01) were observed between RST recorded in the specimens studied. Highest genetic distance (0.604) and lowest genetic resemblance (0.547) were observed between specimens from Fishery zones 2 and 4. Lowest genetic distance (0.311) and highest genetic resemblance (0.733) was observed between specimens from Turkmenistan and specimens from Fishery zone 1. Based on the genetic dendrogeram tree derived by applying UPGMA algorithm, A. stellatus specimens from Fishery zone 2 or in other words specimens from the Sepidrud River belong to one cluster which divides into two clusters, one of which includes specimens from Fishery zones 1, 3 and 4 and specimens from Turkmenistan while the other cluster includes specimens from Ural, Volga and Kura Rivers. It is thus evident that the main population of this species belongs to the Sepidrud River. Results obtained from the present study show that at least eight different populations of A. stellatus are found in the north and south Caspian Sea, four of which are known populations including the Ural River population, the Volga River population, the Kura River population and the Sepidrud River populations. The four other populations identified belonging to Fishery zones 1, 3, and 4 and to Turkmenistan are most probably late or early spawners of the spring run and autumn run of each of the major rivers mentioned. Specific markers were also identified for each of the populations identified. The Ural River population can be identified using primers Spl-68, 54b and Spl-104, 163 170, 173, the Volga River population can be identified using primers LS-54b and Spl-104, 170, 173 113a and similarly the population from the Kura River can be identified using primers LS-34, 54b and Spl-163, 173 and that from the Sepidrud River can be identified using primers LS-19, 34, 54b and Spl-105, 113b. This study gives evidence of the presence of different populations of this species and calls for serious measures to be taken to protect the genetic stocks of these populations. Considering that the population of A. stellatus in Fishery zone 2 is an independent population of the Sepidrud River in the Gilan Province, the catch of these fishes in the region needs to be controlled and regulated in order to restore the declining stocks of this species.

The genetic structure and phylogenetics of pikeperch (Sander lucioperca) Anzali and Amirkolaye wetlands and perch (Perca fluviatilis) populations in Aras Dam and south-west of the Caspian Sea

The genetic structure of pikeperch (Sander lucioperca) and perch (Perca fluviatilis) populations was studied using microsatellite technique. A total of 207 specimens of adult pikeperch were collected from Aras dam (57 specimens), Anzali wetland (50 specimens), Talesh (50 specimens) and Chaboksar (50 specimens) coasts. Also a total of 158 specimens of adult perch were collected from Anzali (Abkenar (50 specimens)and Hendekhale(48 specimens)) and Amirkolaye(60 specimens) wetlands. About 2 g of each specimen's dorsal fin was removed, stored in 96% ethyl alcohol and transferred to the genetic laboratory of the International Sturgeon Research Institute. Genomic DNA was extracted using ammonium-acetate method. The quality and quantity of DNA was assessed using 1% agarose gel electrophoresis. Polymerase Chain Reaction (PCR) was conducted on the target DNA using 15 pairs of microsatellite primers. PCR products were electrophoresed on poly acryl amide gels (6%) that were stained that were stained using silver nitrate. DNA bands were analyzed with BioCapt software. Allele count and frequency, genetic diversity, expected and observed heterozygosity , allele number and the effective allele number, genetic similarity and genetic distance, Fst, Rst, Hardy Weinberg Equilibrium based on X2 and Analysis of Molecular Variance (AMOVA) at 10% confidence level was calculated using the Gene Alex software. Dendogram for genetic distances and identities were calculated using TFPGA program for any level of hierarchy. The results for P. fluviatilis showed that from 15 pair of primers that were examined 6 polymorphic and 7 monomorphic loci were produced, while 2 loci didn't produce any DNA bands. Mean allele number was 4.1±1.1 and mean observed and expected heterozygosity was 0.56±0.12 and 0.58±0.14 respectively. It was also seen that specimens from all regions were not in Hardy Weinberg Equilibrium in some of loci (P<0.001). Highest Fst (0.095) with Nm=2.37 was observed between Hendekhale and Amirkolaye and the lowest Fst (0.004) with Nm=59.31 was observed between Abkenar and Hendekhale. According to AMOVA Significant difference (P<0.05) was observed between recorded Rst in the studied regions in Anzali and Amirkolaye lagoons. In another words there are two distinct populations of this species in Anzali and Amirkolaye lagoons. The highest genetic distance (0.181) and lowest genetic resemblance (0.834) were observed between specimens from Hendekhale and Amirkolaye and the lowest genetic distance (0.099) and highest genetic 176 resemblance (0.981) were observed between specimens from Abkenar and Hendekhale. Based on the genetic dendogram tree derived by applying UPGMA algorithm, specimens from Anzali and Amirkolaye wetlands have the same ancestor. On the other hand there is no noticeable genetic distance between the specimens of these two regions. Also the results for S. lucioperca showed that from 15 pair of primers that were examined 6 polymorphic and 7 monomorphic loci were produced, while 2 loci didn't produce any DNA bands. Mean allele number was 3.0±0.6 and mean observed and expected heterozygosity was 0.52±0.21 and 0.50±0.14 respectively. It was also seen that specimens from all regions were not in Hardy Weinberg Equilibrium in some of loci (P<0.001). Highest Fst (0.093) with Nm=2.43 was observed between Aras dam and Anzali wetland and the lowest Fst (0.022) with Nm=11.27 was observed between Talesh and Chaboksar coasts. Significant differences (P<0.05) were observed between recorded Rst in the studied regions exept for Talesh and Chaboksar Coasts. In another words there are three distinct populations of this species in Caspian sea, Anzali wetland and Aras dam. Highest genetic distance (0.110) and lowest genetic resemblance (0.896) were observed between specimens from Aras dam and Anzali wetland and the lowest genetic distance (0.034) and highest genetic resemblance (0.966) were observed between specimens from Talesh and Chaboksar coasts. Based on the genetic dendogram tree derived by applying UPGMA algorithm, specimens from Talesh and Chaboksar coasts have the lowest genetic distance. On the other hand the main population of this species belongs to Anzali wetland. Phylogenetic relationship of these two species was inferred using mitochondrial cytochrome b gene sequencing. For this purpose 2 specimens of P. fluviatilis from Anzali wetland, 2 specimens of S. lucioperca from Aras dam and 2 specimens of S. lucioperca from Anzali wetland were sequenced and submitted in Gene Bank. These sequences were aligned with Clustal W. The phylogenic relationships were assessed with Mega 4. The results of evolutionary history studies of these species using Neighbor-Joining and Maximum Parsimony methods showed that the evolutionary origin of pikeperch in Aras Dam and Anzali wetland is common. On the other hand these two species had common ancestor in about 4 million years ago. Also different sequences of any region specimens are supposed as different haplotypes. 177 As a conclusion the results of this study showed that microsatellite and mtDNA sequencing methods respectively are effective in genetic structure and phylogenic studies of P. fluviatilis and S. lucioperca.

Traitement des mélanges par le système trigéminal

Le système trigéminal –tout comme l’olfaction et la gustation– est un sens chimique qui permet la perception des informations chimiosensorielles de notre environnement. Contrairement à l’olfaction et à la gustation, notre connaissance du traitement des mélanges par le système trigéminal est limitée. Nous avons donc utilisé des mélanges de trois agonistes relativement spécifiques à des récepteurs (eucalyptol, agoniste TRPM8; aldéhyde cinnamique, agoniste TRPA1 ; camphre, agoniste TRPV1) et d’une odeur pure (alcool phényléthylique) dans différentes proportions afin de déterminer les dimensions de base de la perception trigéminale. Quatre dimensions principales se sont avérées pertinentes: l’intensité, la sensation de chaleur, la sensation de froid et la douleur. Nous avons utilisé ces dimensions pour étudier la perception de mélanges et de combinaisons dans différentes proportions d’un stimulus qui procure une sensation de froid (eucalyptol) et d’un stimulus qui procure une sensation de chaleur (aldéhyde cinnamique). Les résultats indiquent que les mélanges obtiennent généralement des scores plus élevés que les combinaisons sur les dimensions « intensité », « sensation de chaleur » et « douleur » alors que les combinaisons obtiennent des scores plus élevés sur la dimension « sensation de froid ». Ces résultats suggèrent des interactions spécifiques pour les différentes dimensions de la perception trigéminale. Nous en venons à la conclusion d’un effet d’additivité pour les mélanges sur les dimensions « intensité », « sensation de chaleur » et « douleur » alors que nous observons plutôt un effet de suppression de la perception de froid pour les deux stimuli dans les mélanges, ce qui semble indiquer des interactions particulières pouvant prendre place aux niveaux périphérique ou central.

Emission of polycyclic aromatic hydrocarbons from gasohol and ethanol vehicles

The exhaust emission of the polycyclic aromatic hydrocarbons (PAHs) considered toxic to human health were investigated on two spark ignition light duty vehicles, one being gasohol (Gasohol, in Brazil, is the generic denomination for mixtures of pure gasoline plus 20-25% of anhydrous ethyl alcohol fuel (AEAF).)-fuelled and the other a flexible-fuel vehicle fuelled with hydrated ethanol. The influence of fuel type and quality, aged lubricant oil type and use of fuel additives on the formation of these compounds was tested using standardized tests identical to US FTP-75 cycle. PAH sampling and chemical analysis followed the basic recommendations of method TO-13 (United States. Environmental Protection Agency, 1999. Compendium Method TO-13A - Determination of polycyclic Aromatic hydrocarbons (PAH) in Ambient Air Using Gas Chromatography/Mass Spectrometry (CG/MS). Center for environmental research information, Cincinnati, p. 78), with the necessary modification for this particular application. Results showed that the total PAH emission factor varied from 41.9 mu g km(-1) to 612 mu g km(-1) in the gasohol vehicle, and from 11.7 mu g km(-1) to 27.4 mu g km(-1) in the ethanol-fuelled vehicle, a significant difference in favor of the ethanol vehicle. Generally, emission of light molecular weight PAHs was predominant, while high molecular weights PAHs were not detected. In terms of benzo(a)pyrene toxicity equivalence, emission factors varied from 0.00984 mu g TEQ km(-1) to 4.61 mu g TEQ km(-1) for the gasohol vehicle and from 0.0117 mu g TEQ km(-1) to 0.0218 mu g TEQ km(-1) in the ethanol vehicle. For the gasohol vehicle, results showed that the use of fuel additive causes a significant increase in the emission of naphthalene and phenanthrene at a confidence level of 90% or higher; the use of rubber solvent on gasohol showed a reduction in the emission of naphthalene and phenanthrene at the same confidence level; the use of synthetic oil instead of mineral oil also contributed significantly to a decrease in the emission of naphthalene and fluorene. In relation to the ethanol vehicle, the same factors were tested and showed no statistically significant influence on PAH emission. (c) 2008 Elsevier Ltd. All rights reserved.

Characterization and spectroscopic analysis of phenol-ethanol hydrogen bonded clusters

Different hydrogen bonded clusters involving phenol and ethanol are studied theoretically using MP2/aug-cc-pVDZ. Nine different 1: 1 clusters are obtained and analyzed according to their stability and spectroscopic properties. Different isomeric forms of ethanol are considered. Attention is also devoted to the spectral shift of the characteristic pi -> pi* transition of phenol. Using TDHF, CIS, CIS(D) and TDB3LYP in aug-cc-pVDZ basis set, all results agree that a red shift is obtained when phenol is the hydrogen donor and a blue shift is obtained in the opposite case. These results are used to rationalize the red shift observed for phenol in liquid ethanol. (C) 2010 Elsevier B.V. All rights reserved.

Corrosão de vários materiais metálicos em álcool etílico hidratado combustível e sua inibição a 25 graus C

Estudou-se o comportamento à corrosão de diversos materiais metálicos como aço, cobre, latão e pares galvânicos (aço-latão) em álcool etilico combustível (91.1 - 93.9 -INPM) adicionado de várias substâncias a fim de avaliar possíveis efeitos inibidores ou aceleradores da corrosão. Foi verificado a influência na corrosão, de ion cloreto, acetato de sódio, ácido benzóico, trietanolamina, butinodiol e um inibidor comercial. O acetato de sódio seguido do produto comercial se revelaram os melhores aditivos sob o ponto de vista da inibição da corrosão. A adição de cloreto, como um possível contaminante foi estudada e obteve-se um aumento bastante grande na taxa de corrosão. A adição de perclorato de potássio ao álcool combustível normalmente utilizado para aumentar a condutividade da solução nos ensaios eletroquímicos, mostrou ser prejudicial por modificar apreciavelmente as características do comportamento à corrosão dos materiais ensaiados, aumentando-a ou diminuindo-a conforme o caso.

Obtenção e caracterização de dióxido de estanho nanoestruturado pelo método de síntese contínua por combustão em solução

Continuous Synthesis by Solution Combustion was employed in this work aiming to obtain tin dioxide nanostructured. Basically, a precursor solution is prepared and then be atomized and sprayed into the flame, where its combustion occurs, leading to the formation of particles. This is a recent technique that shows an enormous potential in oxides deposition, mainly by the low cost of equipment and precursors employed. The tin dioxide (SnO2) nanostructured has been widely used in various applications, especially as gas sensors and varistors. In the case of sensors based on semiconducting ceramics, where surface reactions are responsible for the detection of gases, the importance of surface area and particle size is even greater. The preference for a nanostructured material is based on its significant increase in surface area compared to conventional microcrystalline powders and small particle size, which may benefit certain properties such as high electrical conductivity, high thermal stability, mechanical and chemical. In this work, were employed as precursor solution tin chloride dehydrate diluted in anhydrous ethyl alcohol. Were utilized molar ratio chloride/solvent of 0,75 with the purpose of investigate its influence in the microstructure of produced powder. The solution precursor flux was 3 mL/min. Analysis with X-ray diffraction appointed that a solution precursor with molar ratio chloride/solvent of 0,75 leads to crystalline powder with single phase and all peaks are attributed to phase SnO2. Parameters as distance from the flame with atomizer distance from the capture system with the pilot, molar ratio and solution flux doesn t affect the presence of tin dioxide in the produced powder. In the characterization of the obtained powder techniques were used as thermogravimetric (TGA) and thermodiferential analysis (DTA), particle size by laser diffraction (GDL), crystallographic analysis by X-ray diffraction (XRD), morphology by scanning electron microscopy (SEM), transmission electron microscopy (TEM), specific surface area (BET) and electrical conductivity analysis. The techniques used revealed that the SnO2 exhibits behavior of a semiconductor material, and a potentially promising material for application as varistor and sensor systems for gas

UTILIZAÇÃO da PRÓPOLIS E ÁLCOOL ETÍLICO NO CONTROLE DE Salmonella em RAÇÕES AVÍCOLAS

Em quatro experimentos foram avaliados como agentes antibacterianos os produtos própolis em solução alcoólica e álcool etílico, adicionados às rações artificialmente contaminadas com os respectivos sorotipos: Salmonella typhimurium Nalr - Specr, (resistentes ao ácido Nalidíxico e a Spectinomicina) nos três primeiros experimentos e Salmonella agona Nalr - Specr, Salmonella infantis Nalr - Specr e Salmonella enteritidis Nalr - Specr no quarto experimento. As rações foram fornecidas a grupos de 10-16 pintos de corte de um dia. em todos os experimentos os produtos testados foram adicionados na base de 2% da ração. Quando se utilizou solução hidroalcóolica de própolis (exp. 1), seguidas 120 horas após o desafio, detectou-se a presença da bactéria nos cecos. No segundo experimento, testou-se a solução de própolis e seu diluente, o álcool etílico; seguidas 96 horas após o desafio, não foi observada a presença da bactéria nos cecos (< 2,0 log10). Avaliou-se, no terceiro experimento, a ação da solução de própolis e do álcool etílico no tempo, adicionados na ração 14 dias e 28 dias antes do fornecimento às aves. Após 72 horas do desafio, a leitura nas placas acusou a presença da bactéria nos cecos. Dentro deste último período, também se avaliou a ação da própolis em pó (extrato seco) e esse mesmo extrato em uma solução aquosa, adicionados à ração 48 horas antes do fornecimento às aves sendo que os resultados confirmaram a presença da bactéria nos cecos. No quarto experimento avaliou-se somente o álcool etílico nas rações artificialmente contaminadas com os sorotipos S. agona, S. enteritidis e S. infantis, registrando-se contagem zero (<2,0 log10) apenas com o último sorotipo. Os resultados obtidos permitem concluir que o tratamento com a solução de própolis apresentou ação sobre a S. typhimurium somente quando em solução alcóolica, dentro de um período de 48 horas, indicando que o efeito bactericida se deveu ao álcool etílico presente na solução. A ação do tratamento com o álcool etílico sobre os demais sorotipos demonstrou resultado parcial sendo observado efeito bactericida nos sorotipos S. typhimurium e S. enteritidis artificialmente inoculados na ração.

Extração, caracterização e aplicação do corante de urucum (Bixa orellana L.) no tingimento de fibras naturais

The increasing demand for natural dyes in place of synthetic ones is justified by the non-toxicity or low toxicity of the former. The synthetic dyes are associated with diseases like cancer as well as when released in the environment takes longer to degrade and the intermediates could be still more toxic. The Annatto (Bixa Orellana L.) is a carotenoid and one of the more important natural dyes used in the food industry. In the form of dye, it represents nearly 70% of the world natural dye production and 90% in Brazil. In the present work, annatto seeds were used of the species peruana paulista, which had nearly 2.1% of bixin. The process of dye extraction with ethyl alcohol showed 4% of dye in the form of powder with particle diameter of 28mm. The extraction process did not alter the chemical composition of the dye, which was confirmed by the electronic spectrum of absorption. Dyeings were carried out with different mordents to study the total colour difference as well as the wash fastness properties and friction fastness properties under wet and dry conditions. The samples treated with copper sulphate showed colour difference but at the same time showed better fastness results. The samples treated with resin (no formaldehyde) did not alter the colour significantly still better the fastness properties. From the results, it could be stated that the resin could be an alternative for heavy metallic mordents