Optimized design of high power mid-infrared Er3+, Pr3+ -codoped ZBLAN fiber laser

Based on the rate equations describing the operation of the Er3+, Pr3+ -codoped ZBLAN fiber lasers with different pump configurations, theoretical calculations that relate to the population characteristics and optimization of CW operation of high power Er3+, Pr3+ :ZBLAN double-clad fiber lasers are presented. Using the measured ET (energy-transfer), ETU (energy-transfer-upconversion) and CR (cross-relaxation) parameters relevant to Er3+, Pr3+ -codoped ZBLAN, a good agreement between the theoretical results from the model and recently reported experimental measurements is obtained. The effects on the slope efficiency of a number of laser parameters including fiber length, reflectance of the output mirror and pumping configuration are quantitatively analyzed and used for the design and optimization of high power Er3+, Pr3+ -codoped ZBLAN fiber lasers.

Optimized design of high power mid-infrared Er3+, Pr3+ -codoped ZBLAN fiber laser

Based on the rate equations describing the operation of the Er3+, Pr3+ -codoped ZBLAN fiber lasers with different pump configurations, theoretical calculations that relate to the population characteristics and optimization of CW operation of high power Er3+, Pr3+ :ZBLAN double-clad fiber lasers are presented. Using the measured ET (energy-transfer), ETU (energy-transfer-upconversion) and CR (cross-relaxation) parameters relevant to Er3+, Pr3+ -codoped ZBLAN, a good agreement between the theoretical results from the model and recently reported experimental measurements is obtained. The effects on the slope efficiency of a number of laser parameters including fiber length, reflectance of the output mirror and pumping configuration are quantitatively analyzed and used for the design and optimization of high power Er3+, Pr3+ -codoped ZBLAN fiber lasers.

Highly sensitive liquid-level sensor based on dual-wavelength double-ring fiber laser assisted by beat frequency interrogation

A highly sensitive liquid-level sensor based on dual-wavelength single-longitudinal-mode fiber laser is proposed and demonstrated. The laser is formed by exploiting two parallel arranged phase-shift fiber Bragg gratings (ps-FBGs), acting as ultra-narrow bandwidth filters, into a doublering resonators. By beating the dual-wavelength lasing output, a stable microwave signal with frequency stability better than 5 MHz is obtained. The generated beat frequency varies with the change of dual-wavelength spacing. Based on this characteristic, with one ps-FBG serving as the sensing element and the other one acting as the reference element, a highly sensitive liquid level sensor is realized by monitoring the beat frequency shift of the laser. The sensor head is directly bonded to a float which can transfer buoyancy into axial strain on the fiber without introducing other elastic elements. The experimental results show that an ultra-high liquidlevel sensitivity of 2.12 × 107 MHz/m within the measurement range of 1.5 mm is achieved. The sensor presents multiple merits including ultra-high sensitivity, thermal insensitive, good reliability and stability. © 2012 Optical Society of America.

掺镱双包层光纤放大器高功率脉冲放大特性

从放大器速率方程出发，分析了掺镱双包层光纤放大器的放大特性。模拟计算了无信号输入时放大器上能级粒子数、泵浦功率和放大自发辐射（ASE）在放大器中的稳态分布。分析了前向和后向泵浦时，高功率高斯脉冲放大时的脉冲波形畸变、上能级粒子数的时间特性、放大器存储能量和脉冲能量演化等动态特性。讨论了掺镱双包层光纤放大器输出脉冲能量随不同输入脉冲峰值功率和泵浦功率的关系。该模型和结论对高功率脉冲放大器的设计和优化具有一定的理论指导意义。

高功率光纤激光器抽运耦合技术研究进展

综述了双包层光纤激光器端面、侧面和集中抽运耦合技术，分析表明侧面抽运耦合技术比端面抽运耦合技术更有利于获得高功率输出，其中分布包层抽运耦合技术是很理想的一种侧面抽运耦合方式。阐述了高功率光纤激光器的特点并介绍了光子晶体光纤和螺旋芯光纤的抽运耦合方式。

掺镱双包层光纤放大器的放大特性

从掺镱(Yb)光纤放大器的功率传输方程出发,利用有限差分法对小模场面积(SMA)和大模场面积(LMA)掺镱双包层光纤放大器的放大特性进行了分析比较。采用模场直径(MFD)6.5 μm和20 μm的双包层掺镱光纤作为放大器增益介质进行窄线宽连续信号的放大,在915 nm激光抽运下模拟计算了大、小模场面积输出功率随输入信号功率、抽运光功率和光纤长度的变化特性,特别是对于大模场面积光纤放大器,最优光纤长度的选择至关重要;讨论了模场直径不同时的最优抽运功率和光纤长度的选择,得出4 m光纤放大时的临界抽运功率为4

不同腔结构下的声光调Q双包层光纤激光器特性研究

报道了半导体激光器端面抽运不同结构的声光调Q的双包层光纤激光器的脉冲输出特性.对前向、后向不同抽运方式的掺镱调Q双包层光纤激光器在输出平均功率,调Q脉冲宽度及脉冲稳定性进行了对比及讨论;其中后向抽运的光纤激光器,在10kHz重复频率调制下,获得了斜效率为60%的平均功率输出,其脉冲宽度为52ns,单脉冲能量为0·3mJ.最后利用不同抽运方式下的速率方程,理论分析调Q脉冲的特性,分析结果与实验相符.

PPLT倍频宽线宽掺镱双包层光纤放大激光

分别通过理论和实验研究了周期性极化的钽酸锂（PPLT）倍频宽线宽准连续掺镱双包层光纤放大激光．PPLT样品长为40mm，极化周期为7．67μm．基频光的中心波长为1064nm，线宽约为6nm。从基频光的光谱特性出发，利用超晶格倍频理论，解释了实验中获得的倍频温度与二次谐波功率之间的关系．在基频光的功率为2．2W时，获得的宽线宽光纤激光倍频效率为1．8％。

采用国产大模场面积双包层光纤的714W连续光纤激光器

采用两个中心波长约976nm准直输出的高功率半导体激光模块为抽运源，通过空间滤波和非球面透镜耦合技术，双端抽运长度为21m的大模场面积国产掺镱双包层光纤，获得了714．5W的高功率连续激光输出。采用反向抽运，当人纤抽运功率为760W时，激光输出功率达到501W；采用双端抽运，当人纤抽运功率为1137W时，获得了714．5W的高功率连续输出，光光转换效率为62．8％，斜率效率为67％。

国产掺镱双包层光纤的激光特性

采用MCVD方法研发了掺镱双包层光纤，并对其结构特性、荧光特性和激光特性进行了测试和研究。其D形内包层尺寸为400／450μm，数值孔径为0．36，纤芯直径约为16μm，数值孔径约为0．18。荧光谱线的范围为1000-1140nm，1030nm处的峰宽大于50nm。采用大功率激光二极管单端泵浦6m长的双包层光纤，在泵浦人纤功率为61W时，获得了32W的激光输出，斜率效率为64％。该光纤在高功率处未发现饱和现象，通过优化光纤参数与泵浦方式还可以提高转化效率和输出功率。实验表明该光纤可以取代进口光纤用作高功率

7.3 W国产单频光纤放大器

报道了一种MOPA式国产单频光纤放大器。该放大器采用连续波单频激光器作为主振荡器，采用我国自行设计和制造的大模场面积掺Yb双包层光纤作为功率放大器，在波长1064 nm处实现了最高7.3 W的连续激光输出，斜率效率为39%，光－光转换效率为26%。此外，对光谱特性及放大的自发发射的抑制也进行了探讨。

高功率双包层光纤放大器

高功率双包层光纤放大器在光纤传感、光纤通讯、光谱测量和惯性约束聚变等领域有广泛应用。介绍了两种获得放大激光输出的高功率双包层光纤放大器：单频双包层光纤放大器和脉冲双包层光纤放大器。分析了它们的工作原理及关键技术，并对国内外近期进展作了综述。

种子光功率对脉冲双包层光纤放大器性能的影响

采用国产的大模场面积双包层光纤和(2+1)×1多模泵浦耦合器，研制出近衍射极限输出的MOPA式脉冲光纤放大器。基于该放大器，发现种子光输出平均功率对放大性能有一定的影响。在泵浦功率一定的情况下，为保证脉冲光纤放大器稳定可靠地运行，对种子光功率来讲，存在一个特定的取值范围。种子光输出平均功率70 mW时，对该脉冲光纤放大器的放大性能进行了研究。

瓦级双包层光纤超荧光光源的实验研究

采用大功率半导体激光器抽运25m掺Yb双包层光纤，在单程装置中，前向(SPF)和后向(SPB)分别获得了1．46w和1．82w最大超荧光功率，斜度效率分别为23．4％0和29．2％，3dB带宽最大为11nm。采用特定范围波长双色镜作为前腔镜，形成双程前向(DPF)装置，获得最大超荧光输出功率2．12W，此时斜度效率为43．2％，中心波长在1070nm，输出光谱平坦性较好，3dB带宽从单程的11nm提高到42nm。

Electromagnetic analysis of novel class of multiple core/multiple clad step index single mode optical fiber by analytical means

General propagation properties and universal curves are given for double clad single mode fibers with inner cladding index higher or lower than the outer cladding index, using the parameter: inner cladding/core radii ratio. Mode cut-off conditions are also examined for the cases. It is shown that dispersion properties largely differ from the single clad single mode fiber case, leading to large new possibilities for extension of single mode operation for large wavelength tange. Paper demonstrates that how substantially we can extend the single mode operation range by using the raised inner cladding fiber. Throughout we have applied our own computations technique to find out the eigenvalue for a given modes. Detail derivations with all trivial mathematics for eigenmode equation are derived for each case. Paper also demonstrates that there is not much use of using depressed inner cladding fiber. We have also concluded that using the large inner cladding/inner core radius we can significantly increase the single mode operation range for the large wavelength region. (C) 2015 Elsevier GmbH. All rights reserved.