Anaerobic retting of banana and arecanut wastes in a plug flow digester for recovery of fiber, biogas and compost

Leaves and leaf sheath of banana and areca husk (Areca catechu) constitute an important component of urban solid waste (USW) in India which are difficult to degrade under normal windrow composting conditions. A successful method of anaerobic digestion built around the fermentation properties of these feedstock has been evolved which uses no moving parts, pretreatment or energy input while enabling recovery of four products: fiber, biogas, compost and pest repellent. An SRT of 27 d and 35 d was found to be optimum for fiber recovery for banana leaf and areca husk, respectively. Banana leaf showed a degradation pattern different from other leaves with slow pectin-1 degradation (80%) and 40% lignin removal in 27 d SRT. Areca husk however, showed a degradation pattern similar to other plant biomass. Mass recovery levels for banana leaf were fiber-20%, biogas-70% (400 ml/g TS) and compost-10%. For areca husk recovery was fiber-50%, biogas-45% (250 ml/g TS) and compost-5%. (C) 2012 Elsevier Inc. All rights reserved.

Full Chemical Kinetic Simulation of Biogas Early Phase Combustion in SI Engines

This paper presents computational work on the biogas early phase combustion in spark ignition (SI) engines using detailed chemical kinetics. Specifically, the early phase combustion is studied to assess the effect of various ignition parameters such as spark plug location, spark energy, and number of spark plugs. An integrated version of the KIVA-3V and CHEMKIN codes was developed and used for the simulations utilizing detailed kinetics involving 325 reactions and 53 species The results show that location of the spark plug and local flow field play an important role. A central plug configuration, which is associated with higher local flow velocities in the vicinity of the spark plug, showed faster initial combustion. Although a dual plug configuration shows the highest rate of fuel consumption, it is comparable to the rate exhibited by the central plug case. The radical species important in the initiation of combustion are identified, and their concentrations are monitored during the early phase of combustion. The concentration of these radicals is also observed to correlate very well with the above-mentioned trend.Thus, the role of these radicals in promoting faster combustion has been clearly established. It is also observed that the minimum ignition energy required to initiate a self-sustained flame depends on the flow field condition in the vicinity of the spark plug.Increasing the methane content in the biogas has shown improved combustion.

Strategies for high efficiency and stability in biogas-fuelled small engines

This work assesses the performance of small biogas-fuelled engines and explores high-efficiency strategies for power generation in the very low power range of less than 1000 W. Experiments were performed on a small 95-cc, single-cylinder, four-stroke spark-ignition engine operating on biogas. The engine was operated in two modes, i.e., `premixed' and `fuel injection' modes, using both single and dual spark plug configurations. Measurements of in-cylinder pressure, crank angle, brake power, air and fuel flow rates, and exhaust emissions were conducted. Cycle-to-cycle variations in engine in-cylinder pressure and power were also studied and assessed quantitatively for various loading conditions. Results suggest that biogas combustion can be fairly sensitive to the ignition strategies thereby affecting the power output and efficiency. Further, results indicate that continuous fuel injection shows superior performance compared to the premixed case especially at low loads owing to possible charge stratification in the engine cylinder. Overall, this study has demonstrated for the first time that a combination of technologies such as lean burn, fuel injection, and dual spark plug ignition can provide highly efficient and stable operation in a biogas-fuelled small S.I. engine, especially in the low power range of 450-1000W. (C) 2014 Elsevier Inc. All rights reserved.

Performance Assessment of a Small Biogas-fuelled Power Generator Prototype

This study reports the development and performance evaluation of prototypes of biogas-fuelled stationary power generators in the range of 1 kW. Strategies to achieve high engine efficiency namely pulsed manifold injection, electronic throttle control and dual spark plugs, have been incorporated in the prototype. A complete closed-loop control of the engine operation to maintain a steady engine speed of 3000 rpm (+/- 5%) across the entire load range while maintaining an optimum fuel-air equivalence ratio is made possible by an electronic control unit (ECU) controlling the injection duration, ignition timing and throttle position. This study specifically focuses on the response of the generator to transient loads, and the overall efficiency obtained. The results obtained from testing the prototype have been found to be satisfactory and show that biogas power generators for low power applications can be made efficient (overall efficiency of 19% at electrical load of 640 W) using the strategies of biogas fuel injection.

SWEETENING OF BIOGAS IN SPRAY TOWERS FOR POWER GENERATION

This paper presents the experience of the new design of using impinging jet spray columns for scrubbing hydrogen sulfide from biogas that has been developed by Indian Institute of Science and patented. The process uses a chelated polyvalent metal ion which oxidizes the hydrogen sulfide to sulfur as a precipitate. The sulfur generated is filtered and the scrubbing liquid recycled after oxidation. The process involves in bringing contact the sour gas with chelated liquid in the spray columns where H2S reacts with chelated Fe3+ and precipitates as sulfur, whereas Fe3+ gets reduced to Fe2+. Fe2+ is regenerated to Fe3+ by reaction of oxygen in air in a separate packed column. The regenerated liquid is recirculated. Sulfur is filtered and separated as a byproduct. The paper presents the experience in using the spray towers for hydrogen sulfide removal and further use of the clean gas for generating power using gas engines. The maximum allowable limit of H2S for the gas engine is 200 ppm (v/v) in order to prevent any corrosion of engine parts and fouling of the lubricating oil. With the current ISET process, the hydrogen sulfide from the biogas is cleaned to less than 100 ppm (v/v) and the sweet gas is used for power generation. The system is designed for 550 NM3/hr of biogas and inlet H2S concentration of 2.5 %. The inlet concentration of the H2S is about 1 - 1.5 % and average measured outlet concentration is about 30 ppm, with an average gas flow of about 300 - 350 NM3/hr, which is the current gas production rate. The sweet gas is used for power generation in a 1.2 MWe V 12 engine. The average power generation is about 650 - 750 kWe, which is the captive load of the industry. The plant is a CHP (combined heat power) unit with heat from the cylinder cooling and flue being recovered for hot water and steam generation respectively. The specific fuel consumption is 2.29 kWh/m(3) of gas. The system has been in operation for more than 13,000 hours in last one year in the industry. About 8.4 million units of electricity has been generated scrubbing about 2.1 million m3 of gas. Performance of the scrubber and the engine is discussed at daily performance level and also the overall performance with an environment sustenance by precipitating over 27 tons of sulfur.

Distribution, relative abundance and developmental morphology of paralarval cephalopods in the Western North Atlantic Ocean

Paralarval and juvenile cephalopods collected in plankton samples on 21 western North Atlantic cruises were identified and enumerated. The 3731 specimens were assigned to 44 generic and specific taxa. This paper describes their spatial and temporal distributions and their developmental morphology. The smallest paralarvae recognized for a number of species are identified and illustrated. The two most abundant and most frequently collected taxa were identifiable to species based on known systematic characters of young, as well as on distribution of the adults. These were the neritic squids Loligo pealeii and Illex illecebrosus collected north of Cape Hatteras, both valuable fishery resources. Other abundant taxa included two morphotypes of ommastrephids, at least five species of enoploteuthids, two species of onychoteuthids, and unidentified octopods. Most taxa were distributed widely both in time and in space, although some seasonal and mesoscale-spatial patterns were indicated. The taxa that appeared to have distinct seasonal distribution included most of the neritic species and, surprisingly, the young of the bathypelagic cranchiids. In eight seasonal cruises over the continental shelf of the middle U.S. Atlantic states, neritic taxa demonstrated approximately the same seasonal patterns during two consecutive years. Interannual differences in the oceanic taxa collected on the shelf were extreme. The highest abundance and diversity of planktonic cephalopods in the oceanic samples were consistently found in the vicinity of the Gulf Stream. Only eight of the oceanic taxa appeared to have limited areal distributions, compared with twelve taxa that were found throughout the western North Atlantic regions sampled in this study. Many taxa, however, were not collected frequently enough to describe seasonal or spatial patterns. Comparisons with published accounts of other cephalopod surveys indicate both strengths and weaknesses in various sampling techniques for capturing the young of oceanic cephalopods. Enoploteuthids were abundant both in our study and in other studies using midwater trawls in several areas of the North Atlantic. Thus, this family probably is adequately sampled over its developmental range. In contrast, octopoteuthids and chtenopterygiids are rare in collections made by small to medium-sized midwater trawls but are comparatively common in plankton samples. For families that are relatively common in plankton samples, paralarval abundance, derived similarly to the familiar ichthyoplankton surveys of fisheries science, may be the most reliable method of gathering data on distribution and abundance. (PDF file contains 58 pages.)

Cephalopods from the stomachs of sperm whales taken off California

Cephalopod remains (beaks, bodies, and parts of bodies) were collected from the stomachs of 157 sperm whales (Physeter macrocephalus) taken off central California (lat. 37°-39°N). At least 24 species representing 14 families were identified. Frequencies of occurrence of the six most numerous taxa were Moroteuthis robusta 72.0%, Gonatopsis borealis 66.2%, Histioteuthis dofleini 36.9%, Galiteuthis spp. (including G. phyllura and G. pacifica) 36.3%, Octopoteuthis deletron 35.0%, and Vampyroteuthis infernalis 27.4%. One find of two Mesonychoteuthis hamiltoni beaks strongly suggests transequatorial migration by one large male sperm whale. (PDF file contains 18 pages.)

Identification and estimation of size from the beaks of 18 species of cephalopods from the Pacific Ocean

A method of identifying the beaks and estimating body weight and mantle length of 18 species of cephalopods from the Pacific Ocean is presented. Twenty specimens were selected from each of the following cephalopod species: Symplectoteuthis oualaniensis, Dosidicus gigas, Ommastrephes bartramii, S. luminosa, Todarodes pacificus, Nototodarus hawaiiensis, Ornithoteuthis volalilis, Hyaloteuthis pelagica, Onychoteuthis banksii, Pterygioteuthis giardi, Abraliopsis affinis, A. felis, Liocranchia reinhardti, Leachia danae, Histioteuthis heteropsis, H. dofleini, Gonalus onyx, and Loligo opalescens. Dimensions measured on the upper and lower beak are converted to ratios and compared individually among the species using an analysis of variance procedure with Tukey's omega and Duncan's multiple range tests. Significant differences (P =0.05) observed among the species' beak ratio means and structural characteristics are used to construct artificial keys for the upper and lower beaks of the 18 species. Upper and lower beak dimensions are used as independent variables in a linear regression model with mantle length and body weight (log transformed). (PDF file contains 56 pages.)

Length-weight relationship of fishes and cephalopods from the Balearic Islands (Western Mediterranean)

Length-weight relationship (LWR) parameters of 72 species of fishes and 15 species of cephalopods caught in the Balearic Islands demersal fishery are reported. This is the first compilation of LWR for these groups in the Balearic Islands.

Taxonomic study of the cephalopods, particularly the Teuthoidea (squids) and Sepoidea [i.e. Sepioidea] (cuttlefish) in the water around Sri Lanka

A preliminary taxonomic study of the local cephalopods has been undertaken. 8 spp have been identified, and a key to the Sepioidea and Teuthoidea of the Ceylon seas is presented. The spp identified are described and illustrated, with notes on distinctive characters, and on distribution

Biochemical investigations on the edible molluscs of Kerala 2. A study on the nutritional value of some gastropods and cephalopods

Data on the biochemical composition and food value of the edible portions of two gastropods, Pila virens and Achatina fulica and two cephalopods, Sepiella inermis and Loigo indica have been presented. These molluscs possess nutritive meat very rich in protein and minerals, which compare favourably with popular food fishes in caloric value. The significance of the variations met with in the biochemical constituents of the different species has been discussed.

Biogas production from novel substrates

Biogas production is the conversion of the organic material into methane (CH4) and carbon dioxide (CO2) under anaerobic conditions. Anaerobic digestion (AD) is widely used in continental and Scandinavian communities as both a waste treatment option and a source of renewable energy. Ireland however lags behind this European movement. Numerous feedstocks exist which could be digested and used to fuel a renewable transport fleet in Ireland. An issue exists with the variety of feedstocks; these need to be assessed and quantified to ascertain their potential resource and application to AD. From literature the ideal C:N ratio is between 25 and 30:1. Low levels of C:N (<15) can lead to problems with ammonia inhibition. Within the digester a plentiful supply of nutrients and a balanced C:N is required for stable performance. Feedstocks were sampled from a range of over 100 different substrates in Ireland including for first, second and third generation feedstocks. The C:N ranged from 81:1 (Winter Oats) to 7:1 (Silage Effluent). The BMP yields were recorded ranging from 38 ± 2.0 L CH4 kg−1 VS for pig slurry (weaning pigs) to 805 ± 57 L CH4 kg−1 VS for used cooking oil (UCO). However the selection of the best preforming feedstock in terms of C:N ratio or BMP yield alone is not sufficiently adequate. A total picture has to be created which includes C:N ratio, BMP yield, harvest yield and availability. Potential feedstocks which best meet these requirements include for Grass silage, Milk processing waste (MPW) and Saccharina latissima. MPW has a potential of meeting over 6 times the required energy for Ireland’s 2020 transport in energy targets. S. Latissima recorded a yield of over 10,000 GJ ha-1 yr-1 which out ranks traditional second generation biofuels by a factor of more than 4.

Algae-Based Purification of Landfill Biogas Using a CO2 Removal System and Helical Photobioreactor in Series

Biogas is a mixture of methane and other gases. In its crude state, it contains carbon dioxide (CO2) that reduces its energy efficiency and hydrogen sulfide (H2S) that is toxic and highly corrosive. Because chemical methods of removal are expensive and environmentally hazardous, this project investigated an algal-based system to remove CO2 from biogas. An anaerobic digester was used to mimic landfill biogas. Iron oxide and an alkaline spray were used to remove H2S and CO2 respectively. The CO2-laden alkali solution was added to a helical photobioreactor where the algae metabolized the dissolved CO2 to generate algal biomass. Although technical issues prevented testing of the complete system for functionality, cost analysis was completed and showed that the system, in its current state, is not economically feasible. However, modifications may reduce operation costs.