Concretes and mortars recycled with water treatment sludge and construction and demolition rubble

There are about 7500 water treatment plants in Brazil. The wastes these plants generate in their decantation tanks and filters are discharged directly into the same brooks and rivers that supply water for treatment. Another serious environmental problem is the unregulated disposal of construction and demolition rubble, which increases the expenditure of public resources by degrading the urban environment and contributing to aggravate flooding and the proliferation of vectors harmful to public health. In this study, an evaluation was made of the possibility of recycling water treatment sludge in construction and demolition waste recycling plants. The axial compressive strength and water absorption of concretes and mortars produced with the exclusive and joint addition of these two types of waste was also determined. The ecoefficiency of this recycling was evaluated by determining the concentration of aluminum in the leached extract resulting from the solubilization of the recycled products. The production of concretes and mortars with the joint addition of water treatment sludge and recycled concrete rubble aggregates proved to be a viable recycling alternative from the standpoint of axial compression strength, modulus of elasticity, water absorption and tensile strength by the Brazilian test method. (C) 2008 Elsevier Ltd. All rights reserved.

Simulation of the micro-physics of rocks using LSMearth

The particle-based Lattice Solid Model (LSM) was developed to provide a basis to study the physics of rocks and the nonlinear dynamics of earthquakes (MORA and PLACE, 1994; PLACE and MORA, 1999). A new modular and flexible LSM approach has been developed that allows different microphysics to be easily included in or removed from the model. The approach provides a virtual laboratory where numerical experiments can easily be set up and all measurable quantities visualised. The proposed approach provides a means to simulate complex phenomena such as fracturing or localisation processes, and enables the effect of different micro-physics on macroscopic behaviour to be studied. The initial 2-D model is extended to allow three-dimensional simulations to be performed and particles of different sizes to be specified. Numerical bi-axial compression experiments under different confining pressure are used to calibrate the model. By tuning the different microscopic parameters (such as coefficient of friction, microscopic strength and distribution of grain sizes), the macroscopic strength of the material and can be adjusted to be in agreement with laboratory experiments, and the orientation of fractures is consistent with the theoretical value predicted based on Mohr-Coulomb diagram. Simulations indicate that 3-D numerical models have different macroscopic properties than in 2-D and, hence, the model must be recalibrated for 3-D simulations. These numerical experiments illustrate that the new approach is capable of simulating typical rock fracture behaviour. The new model provides a basis to investigate nucleation, rupture and slip pulse propagation in complex fault zones without the previous model limitations of a regular low-level surface geometry and being restricted to two-dimensions.

Cromatografia preparativa: caracterização e purificação de produtos e impurezas com aplicação na indústria de APIs

Neste trabalho efectuou-se o desenvolvimento de métodos de purificação de princípios activos farmacêuticos utilizando a cromatografia preparativa em coluna (eluição batch). Por motivos de confidencialidade as amostras tiveram a denominação de Amostra Projecto A, Amostra Projecto B, Amostra Projecto C e Amostra 2 - Projecto A. Estudou-se a performance de coluna para cada projecto utilizando colunas pré-preparadas e colunas preparadas com a tecnologia DAC (Dynamical Axial Compression). Elaborou-se o procedimento experimental de enchimento de colunas preparativas sob compressão axial. As impurezas isoladas por cromatografia preparativa foram sujeitas a caracterização HPLC e LC-MS. Com colunas pré-preparadas, obteve-se para a amostra do projecto A um rendimento de 70,59% e relativamente à amostra projecto B obteve-se u, rendimento de 15,39%. Relativamente à impureza isolada da amostra do projecto A, o estudo por HPLC revelou 98,69% de pureza, quanto à impureza da amostra projecto B obteve-se 88,80% de pureza. A impureza da amostra do projecto A exibiu por LC-MS a massa de 467,15 enquanto que a impureza da amostra do projecto B obteve 503,31. O enchimento de colunas preparativas sob pressão axial dinâmica foi realizado numa coluna de dimensão 260 X 25 mm, onde 76,60% da coluna foi compactada com o material de enchimento SepTech ST150-C18, 10 µm. A coluna foi testada com a impureza isolada do projecto A. Isolou-se o pico referente à impureza, e por LC-MS verificou-se que a impureza foi isolada eficientemente com 97,20& de pureza e massa 467,15 como indicado anteriormente. Em relação à preparação de colunas com a tecnologia DAC concluímos que, neste caso, é mais vantajoso realizar o enchimento das colunas do que efectuar a compra de colunas pré-preparadas. Com estes resultados pode-se concluir que a cromatografia preparativa é um método eficaz no isolamento de impurezas de APIs (Active Pharmaceutical Ingredients) face a métodos de purificação clássicos que foram realizados previamente noutros estudos. Com futuros desenvolvimentos e investimentos, facilmente poderá tornar-se num método de purificação indispensável na Indústria de Química Fina.

Consolidating preservative-treated wood: Combined mechanical performance of boron and polymeric products in wood degraded by Coniophora puteana

When timber elements in heritage buildings are moderately degraded by fungi and assuming underlying moisture problems have been solved, two actions can be taken: i) use a biocide to stop fungal activity; ii) consolidate the degraded elements so that the timber keeps on fulfilling its structural and decorative functions. The aim of this work is to investigate the mechanical performance of maritime pine wood degraded by fungi after being treated with a biocide followed by impregnation with a polymer product. Three commercially available products were used: a boron water-based biocide, an acrylic consolidant and an epoxy-based consolidant. Treated and consolidated specimens were subjected to mechanical tests: axial compression test (NP 618), static surface hardness (ISO 3350) and bending test (NP 619). Sets of replicates were subjected to an evaporation ageing test (EN 73) after application of the products and also tested for mechanical behaviour. An increase in mechanical strength was observed for both consolidants with no significant influence from the previous use of biocide product. The specimens subjected to ageing showed a slightly better general mechanical performance.

Experimental research on rubble stone masonry walls

HMC08 - 1st Historical Mortars Conference: Characterization, Diagnosis, Conservation, Repair and Compatibility, LNEC, Lisbon, 24-26 September 2008

Biomechanical characterization and in vitro mechanical injury of elderly human femoral head cartilage: comparison to adult bovine humeral head cartilage.

OBJECTIVES: In vitro mechanical injury of articular cartilage is useful to identify events associated with development of post-traumatic osteoarthritis (OA). To date, many in vitro injury models have used animal cartilage despite the greater clinical relevance of human cartilage. We aimed to characterize a new in vitro injury model using elderly human femoral head cartilage and compare its behavior to that of an existing model with adult bovine humeral head cartilage. DESIGN: Mechanical properties of human and bovine cartilage disks were characterized by elastic modulus and hydraulic permeability in radially confined axial compression, and by Young's modulus, Poisson's ratio, and direction-dependent radial strain in unconfined compression. Biochemical composition was assessed in terms of tissue water, solid, and glycosaminoglycan (GAG) contents. Responses to mechanical injury were assessed by observation of macroscopic superficial tissue cracks and histological measurements of cell viability following single injurious ramp loads at 7 or 70%/s strain rate to 3 or 14 MPa peak stress. RESULTS: Confined compression moduli and Young's moduli were greater in elderly human femoral cartilage vs adult bovine humeral cartilage whereas hydraulic permeability was less. Radial deformations of axially compressed explant disks were more anisotropic (direction-dependent) for the human cartilage. In both cartilage sources, tissue cracking and associated cell death during injurious loading was common for 14 MPa peak stress at both strain rates. CONCLUSION: Despite differences in mechanical properties, acute damage induced by injurious loading was similar in both elderly human femoral cartilage and adult bovine humeral cartilage, supporting the clinical relevance of animal-based cartilage injury models. However, inherent structural differences such as cell density may influence subsequent cell-mediated responses to injurious loading and affect the development of OA.

Investigation of Steel-Stringer Bridges: Superstructures and Substructures, Volume I, TR-522, 2007

There are hundreds of structurally deficient or functionally obsolete bridges in the state of Iowa. With the majority of these bridges located on rural county roads where there is limited funding available to replace the bridges, diagnostic load testing can be utilized to determine the actual load carrying capacity of the bridge. One particular family or fleet of bridges that has been determined to be desirable for load testing consists of single-span bridges with non-composite, cast-in-place concrete decks, steel stringers, and timber substructures. Six bridges with poor performing superstructure and substructure from the aforementioned family of bridges were selected to be load tested. The six bridges were located on rural roads in five different counties in Iowa: Boone, Carroll, Humboldt, Mahaska, and Marshall. Volume I of this report focuses on evaluating the superstructure for this family of bridges. This volume discusses the behavior characteristics that influence the load carrying capacity of this fleet of bridges. In particular, the live load distribution, partial composite action, and bearing restraint were investigated as potential factors that could influence the bridge ratings. Implementing fleet management practices, the bridges were analyzed to determine if the load test results could be predicted to better analyze previously untested bridges. For this family of bridges it was found that the ratings increased as a result of the load testing demonstrating a greater capacity than determined analytically. Volume II of this report focuses on evaluating the timber substructure for this family of bridges. In this volume, procedures for detecting pile internal decay using nondestructive ultrasonic stress wave techniques, correlating nondestructive ultrasonic stress wave techniques to axial compression tests to estimate deteriorated pile residual strength, and evaluating load distribution through poor performing timber substructure elements by instrumenting and load testing the abutments of the six selected bridges are discussed. Also, in this volume pile repair methods for restoring axial and bending capacities of pile are developed and evaluated.

Estudo da viabilidade técnica da utilização de escórias de aciaria do processo LD como adição em cimentos

A reciclagem de resíduos apresenta-se como uma alternativa adequada com relação à preservação dos recursos naturais e do meio ambiente. As escórias de aciaria são resíduos siderúrgicos originados na fabricação do aço, e são geradas em grandes quantidades. Estes resíduos são estocados nos pátios siderúrgicos, onde permanecem, na sua maioria, sem qualquer destino. Normalmente, as escórias de aciaria são volumetricamente instáveis, apresentando características expansivas, e por esta razão, a aplicação das mesmas em materiais de construção torna-se restrita. Esta pesquisa tem como objetivo estudar a viabilidade técnica do uso das escórias de aciaria LD como adição em cimentos, propondo um método de estabilização por meio de granulação por resfriamento brusco destas escórias, buscando, desta forma, a eliminação do fenômeno da expansão, e visando a melhoria das características destes resíduos. No processo de estabilização, a escória líquida foi granulada em uma usina siderúrgica. Estudos complementares de granulação foram realizados nos laboratórios da UFRGS, empregando-se escórias refundidas. A granulação por resfriamento brusco favoreceu a redução do CaOlivre, a eliminação do MgO na forma de periclásio, e a eliminação do bC2S das escórias, considerados agentes causadores da expansão. No entanto, a elevada basicidade da escória LD dificulta a formação da estrutura vítrea e a separação da fração metálica após o resfriamento brusco. Foram realizados ensaios de expansão das escórias, atividade pozolânica, e resistência mecânica de argamassas com escórias granuladas. O resfriamento brusco proporcionou a eliminação da expansão e o desenvolvimento das propriedades pozolânicas/cimentícias da escória granulada. Como adição em cimentos, do ponto de vista da resistência mecânica, as argamassas compostas com escórias granuladas e clínquer apresentaram níveis de resistência à compressão axial compatíveis com as especificações referentes ao cimento Portland composto, apesar destes resultados serem inferiores aos obtidos para as argamassas de referência.

O Zoledronato no tratamento da osteoporose umeral em ratas: estudo prospectivo e randomizado

OBJETIVO: Investigar as repercussões clínicas, biomecânicas e histomorfométricas do zoledronato no tratamento da osteoporose umeral em ratas osteoporóticas. MÉTODOS: Analisou-se, prospectivamente, 40 ratas (Rattus novergicus albinus). Com 60 dias de vida, foram aleatorizadas em dois grupos de acordo com o procedimento cirúrgico: ooforectomia bilateral (O) (n=20) e pseudo-cirurgia (P) (n=20). Após trinta dias, os animais foram novamente randomizados, de acordo com a administração de 0,1mg/kg de zoledronato (AZ) ou água destilada (AD): OAZ (n=10), OAD (n=10), PAZ (n=10) e PAD (n=10). Após doze meses, os animais foram eutanasiados e seus úmeros retirados. Clinicamente considerou-se o peso dos animais; biomecanicamente foram realizados ensaios compressivos e histomorfometricamente foi determinada a área trabecular óssea. RESULTADOS: Os grupos O tiveram um aumento de peso maior que os grupos P (p=0,005). Os grupos com zoledronato suportaram maior carga máxima que os grupos com água destilada (p=0,02). Nos grupos com zoledronato verificou-se o aumento da área trabecular óssea quando comparados aos grupos com água destilada (p=0,001). Houve correlação positiva entre a área trabecular e a carga máxima (p=0,04; r=0,95). CONCLUSÃO: O zoledronato não influiu no peso dos animais. Os resultados mostraram o aumento da resistência óssea umeral e da área trabecular óssea.

Influência dos constituintes do esgoto no colapso de um solo arenoso

Este trabalho analisa o comportamento colapsível de um solo tropical arenoso inundado com diferentes fluidos de saturação que constituem o esgoto doméstico. Para tal análise, foram levados em consideração parâmetros físicos e químicos e aspectos estruturais do solo no âmbito do fenômeno da colapsibilidade dos solos, assim como as principais características dos fluidos de inundação de água destilada, esgoto doméstico e algumas soluções à base de substâncias que compõem os esgotos e as deformações axiais do solo a um metro de profundidade em ensaios edométricos. As propriedades físicas e químicas dos fluidos de inundação e dos solos, bem como a combinação entre tais propriedades, desempenham relevante papel na compreensão do fenômeno do colapso, mostrando que a sua ocorrência não pode ser atribuída a um ou outro parâmetro do solo ou do fluido isoladamente.

Brazilian results on structural masonry concrete blocks

The purpose of this paper is to study the mechanical behavior of concrete blocks and prisms when performing axial compression tests within the Brazilian base of knowledge, intending to foment data of this kind for a world-based network. The blocks were built using five different mixtures in which the quantity of cement and the compacting ratio (density) were varied (during the fabrication process). The three-course-high prisms were assembled using 1 cm (0.39 in.) thick full-bedded joints, always trying to leave the mortar's characteristics constant. The axial compression tests were conducted according to Brazilian practice code recommendations, because most of these standards are very similar to international practice codes. The compressive strength, strains, and rupture form of each mixture studied were recorded. Attempts were made to correlate the strength, efficiency ratio (block strength/prism strength) of the prisms, strains, and rupture form; with the quantity of cement and compacting ratio. The data are presented in tables and figures, and the obtained results are discussed throughout the text. Copyright © 2007, American Concrete Institute. All rights reserved.

Detecting early biomechanical effects of zoledronic acid on femurs of osteoporotic female rats

Aim. To investigate the biomechanical effects of zoledronic acid (ZA) on femurs of female osteoporotic rats after follow-up periods of 9 and 12 months. Methods. Eighty female Wistar rats were prospectively assessed. At 60 days of age, the animals were randomly divided into two groups: bilateral oophorectomy (O) (n=40) and sham surgery (S) (n=40). At 90 days of age, groups O and S were randomly subdivided into four groups, according to whether 0.1 mg/kg of ZA or distilled water (DW) was intraperitoneally administered: OZA (n=20), ODW (n=20), SZA (n=20), and SDW (n=20). The animals were sacrificed at 9 and 12 months after the administration of the substances, and then their right femurs were removed and analyzed biomechanically. Axial compression tests that focused on determining the maximum load (N), yield point (N), and stiffness coefficient (N/mm) of the proximal femur were performed in the biomechanical study. Results. ZA significantly increased the maximum load and yield point, reducing the stiffness coefficient concerning the oophorectomy status and follow-up period. Conclusion. Zoledronic acid, at a dose of 0.1 mg/kg, significantly increased the maximum loads and yield points and reduced the stiffness coefficients in the femurs of female rats with osteoporosis caused by bilateral oophorectomy. © 2012 Evandro Pereira Palacio et al.

The effect of locked screw angulation on the biomechanical properties of the S.P.S. Free-Block plate

Objectives: Among the locked internal fixators is one denominated S.P.S. (Synthesis Pengo System) Free-Block, which was designed with a locking ring that allows the screw to be locked and positioned obliquely. Due to the paucity of biomechanical studies on this system, the present work aimed to evaluate the influence of locked screw angulation on the resistance of the S.P.S. Free--Block plate. Methods: Forty synthetic bone cylinders with 10 mm fracture gap were used. Forty seven-hole 3.5 mm stainless steel plates (two AO-like dynamic compression holes and five locked holes) were assembled according to the orientation of the locked screws: mono cortical screws were positioned at 90° to the long axis of the cylinder (Group 1), and monocortical screws were positioned at 70° to its cylinder long axis (Group 2). In both groups, AO-like dynamic compression hole screws were positioned bicortically and neutrally. For each group, six specimens were tested until failure, three in bending and three in compression, to determine the loads for fatigue testing. Subsequently, for each group, 14 specimens were tested for failure --seven by bending and seven in compression. Results: No significant failure differences were observed between Groups 1 and 2 under static-loading or fatigue test. Clinical significance: In a fracture gap model the orientation of the locked monocortical screws did not show any influence on the mechanical performance of the S.P.S. Free-Block to tests of axial compression and four-point bending. © Schattauer 2013.

Utilização do pó de pedra basáltica em substituição à areia natural do concreto

Pós-graduação em Engenharia Civil - FEIS

Influência do graute e da taxa de armadura no comportamento da alvenaria de blocos de concreto

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)