Analysis of a linear one-dimensional active noise control system by means of block diagrams and transfer functions

In arriving at the ideal filter transfer function for an active noise control system in a duct, the effect of the auxiliary sources (generally loudspeakers) on the waves generated by the primary source has invariably been neglected in the existing literature, implying a rigid wall or infinite impedance. The present paper presents a fairly general analysis of a linear one-dimensional noise control system by means of block diagrams and transfer functions. It takes into account the passive as well as active role of a terminal primary source, wall-mounted auxiliary source, open duct radiation impedance, and the effects of mean flow and damping. It is proved that the pressure generated by a source against a load impedance can be looked upon as a sum of two pressure waves, one generated by the source against an anechoic termination and the other by reflecting the rearward wave (incident on the source) off the passive source impedance. Application of this concept is illustrated for both the types of sources. A concise closed-form expression for the ideal filter transfer function is thus derived and discussed. Finally, the dynamics of an adaptive noise control system is discussed briefly, relating its standing-wave variables and transfer functions with those of the progressive-wave model presented here.

A simple method for counting bacteria with active electron transport system in water and sediment samples [Translation from: Kiel. Meeresforsch. 31(2) 83-86, 1975]

Description of a simple method for counting bacteria with active electron transport systems in water and sediment samples. Sodium succinate, NADH and NADPH served as electron donors. It is possible to see several sites of electron transport in the larger cells. Especially impressive are the plankton-algae, protozoa, and small metazoa. This is a partial translation of the ”method” section only.

MIMO system capacity improvements using radio-over-fibre distributed antenna system technology

The effect of antenna separation in a 3×3 MIMO system using RoF DAS technology is investigated. Larger antenna separation is found to improve the throughput due to reduced channel correlation and improved SNR. © 2011 Optical Society of America.

Fibre optic distributed sensor system for condition monitoring of synthetic ropes

Reliability of the measuring devices is very important problem. Optical fibre sensors are very efficient. The use of optical fibre sensors for monitoring the physical and chemical parameters has been expanding over resent years. These sensors are applied for monitoring the structural integrity of long, parallel lay synthetic ropes. Such ropes are corrosion free, however, their operational lifetime under cyclic load is not well understood and premature failure can occur due to slippage and breakage of yarns within the rope. The monitoring system has been proposed which is based on acoustic detection of yarn breakage. Monitoring the strain and temperature is performed using the array of fibre gratings distributed along the rope length.

An experimental semi-active anti-roll system

The use of anti-roll bars to provide additional roll stiffness and therefore to reduce the trade-off between ride and rollover performance has previously been studied. However, little work has been carried out to investigate the benefits of a switchable roll stiffness. Such a semi-active anti-roll system has the ability to have a low roll stiffness during straight-ahead driving for improved ride performance and high roll stiffness during cornering for improved roll performance. Modelling of such a system is conducted and the model is validated against a semi-active anti-roll system fitted to an experimental vehicle. Experimental and theoretical investigations are used to investigate the performance of such a system with several different strategies employed to switch to the high-stiffness state. The use of an air suspension on the vehicle to roll into corners is also investigated, as is the possibility of exploiting the road layout by allowing the vehicle to be in a low-roll-stiffness configuration during a corner, and then to switch to the high-roll-stiffness configuration midcorner, hence 'locking in' a roll angle. The best rollover performance improvement that was achieved was 12.5 per cent. © IMechE 2008.

MIMO System capacity improvements using radio-over-fibre distributed antenna system technology

The effect of antenna separation in a 3×3 MIMO system using RoF DAS technology is investigated. Larger antenna separation is found to improve the throughput due to reduced channel correlation and improved SNR. © OSA/OFC/NFOEC 2011.

AIDA-Based Distributed File System

This paper describes a prototype implementation of a Distributed File System (DFS) based on the Adaptive Information Dispersal Algorithm (AIDA). Using AIDA, a file block is encoded and dispersed into smaller blocks stored on a number of DFS nodes distributed over a network. The implementation devises file creation, read, and write operations. In particular, when reading a file, the DFS accepts an optional timing constraint, which it uses to determine the level of redundancy needed for the read operation. The tighter the timing constraint, the more nodes in the DFS are queried for encoded blocks. Write operations update all blocks in all DFS nodes--with future implementations possibly including the use of read and write quorums. This work was conducted under the supervision of Professor Azer Bestavros (best@cs.bu.edu) in the Computer Science Department as part of Mohammad Makarechian's Master's project.