Effect of Mechanical and Geometric Mismatching on Fatigue and Damage of Welded Joints

The future of high technology welded constructions will be characterised by higher strength materials and improved weld quality with respect to fatigue resistance. The expected implementation of high quality high strength steel welds will require that more attention be given to the issues of crack initiation and mechanical mismatching. Experiments and finite element analyses were performed within the framework of continuum damage mechanics to investigate the effect of mismatching of welded joints on void nucleation and coalescence during monotonic loading. It was found that the damage of undermatched joints mainly occurred in the sandwich layer and the damageresistance of the joints decreases with the decrease of the sandwich layer width. The damage of over-matched joints mainly occurred in the base metal adjacent to the sandwich layer and the damage resistance of the joints increases with thedecrease of the sandwich layer width. The mechanisms of the initiation of the micro voids/cracks were found to be cracking of the inclusions or the embrittled second phase, and the debonding of the inclusions from the matrix. Experimental fatigue crack growth rate testing showed that the fatigue life of under-matched central crack panel specimens is longer than that of over-matched and even-matched specimens. Further investigation by the elastic-plastic finite element analysis indicated that fatigue crack closure, which originated from the inhomogeneousyielding adjacent to the crack tip, played an important role in the fatigue crack propagation. The applicability of the J integral concept to the mismatched specimens with crack extension under cyclic loading was assessed. The concept of fatigue class used by the International Institute of Welding was introduced in the parametric numerical analysis of several welded joints. The effect of weld geometry and load condition on fatigue strength of ferrite-pearlite steel joints was systematically evaluated based on linear elastic fracture mechanics. Joint types included lap joints, angle joints and butt joints. Various combinations of the tensile and bending loads were considered during the evaluation with the emphasis focused on the existence of both root and toe cracks. For a lap joint with asmall lack-of-penetration, a reasonably large weld leg and smaller flank angle were recommended for engineering practice in order to achieve higher fatigue strength. It was found that the fatigue strength of the angle joint depended strongly on the location and orientation of the preexisting crack-like welding defects, even if the joint was welded with full penetration. It is commonly believed that the double sided butt welds can have significantly higher fatigue strength than that of a single sided welds, but fatigue crack initiation and propagation can originate from the weld root if the welding procedure results in a partial penetration. It is clearly shown that the fatigue strength of the butt joint could be improved remarkably by ensuring full penetration. Nevertheless, increasing the fatigue strength of a butt joint by increasing the size of the weld is an uneconomical alternative.

Hitsauksen laadunvarmistus teräsrakentamisessa

Suomessa on tapahtunut 2000-luvulla neljä kappaletta ns. suuronnettomuuden vaaratilanteiksi luokiteltavaa teräsrakenteiden vaurioitumisesta aiheutunutta onnettomuutta, joista yksi johti ihmishengen menetykseen. Onnettomuuden syynä oli huonolaatuisten pienahitsien pettäminen kuormituksen alaisena, joka puolestaan oli seurausta puutteellisesta hitsauksen laadunvarmistuksesta. Teräsrakenteiden valmistus ja hitsaus eivät ole yhtä tarkan viranomaisvalvonnan alaista kuten esimerkiksi painelaitteiden valmistus, vaikka teräsrakenteiden vaurioitumisesta aiheutuvat riskit ovat erittäin merkittäviä. Työn tavoitteena oli tutustua onnettomuustapauksiin, teräsrakenteista annettuihin viranomaismääräyksiin sekä ohjeisiin ja esittää laadunvarmistustoimenpiteitä, joiden avulla voidaan varmistua hitsaustyön riittävästä laadusta teräsrakentamisessa. Näitä laadunvarmistustoimenpiteitä ovat mm. hitsaushenkilöstön pätevöinti, hitsausohjeiden käyttäminen, ainetta rikkomattomat tarkastukset ja rakennesuunnitelmien tarkastukset. Toisena tavoitteena oli kartoittaa rakenteiden valmistajien ja pääurakoitsijoiden nykyistä tilannetta laadunvarmistuksen osalta sekä selvittää kiinnostusta kolmannen osapuolen tarjoamiin laadunvarmistuspalveluihin. Kyselyiden perusteella laadunvarmistuspalveluille on olemassa kysyntää tietyin kustannuksiin liittyvin varauksin. Palveluista eniten kiinnostusta herättivät ainetta rikkomattomat tarkastukset ja rakennesuunnitelmien tarkastukset.

Hitsauskoneen kunnonvalvontajärjestelmän kehittäminen

Teollisuuden kasvavien laatuvaatimusten johdosta valmistava teollisuus joutuu tiukentamaan laatuvaatimuksiaan täyttääkseen asiakasvaatimukset. Laatujärjestelmät asettavat valmistajille erilaisia vaatimuksia, kuten valmistuksessa käytettävien laitteistojen huoltodokumentaatioiden tuottaminen. Standardi SFS-EN ISO 3834-2 Metallien sulahitsauksen laatuvaatimukset: Kattavat laatuvaatimukset tuo edellä mainitut vaatimukset myös hitsaustuotantoon. Ennakoivaa kunnossapitoa käytetään monilla teollisuuden aloilla, koska tuotannon yllättävät keskeytymiset halutaan ennaltaehkäistä. Käsinhitsaukseen ei ole ollut toistaiseksi työkaluja, jotka mahdollistaisivat ennakoivan kunnossapidon hitsauskoneille. Kemppi Oy kehittää hitsauksen monitorointiratkaisua, jonka yhtenä päämääränä on kunnonvalvontajärjestelmän kehittäminen hitsauslaitteistolle. Järjestelmä ottaa huomioon myös laatujärjestelmien asettamat vaatimukset hitsauskoneiden huoltodokumentaation tuottamisesta. Diplomityön tavoitteena oli tehdä vaatimusmäärittely hitsauskoneiden kunnonvalvontajärjestelmälle. Tässä diplomityössä perehdyttiin kunnossapidon ja vikaantumisen lajeihin, laatujärjestelmiin sekä hitsauslaitteistoon. Tutkimuksessa syvennyttiin hitsauskoneiden kunnossapidon ja vikaantumistapauksien kautta suunnitteilla olevan järjestelmän tarpeisiin. Haastatteluiden avulla kartoitettiin hitsauslaitteiden kunnonvalvontajärjestelmältä vaadittavia piirteitä, järjestelmälle asetettavia vaatimuksia sekä järjestelmän monitorointikohteita. Tutkimuksen pohjalta laadittuun vaatimusmäärittelyyn saatiin muodostettua toiminnalliset vaatimukset, joista muodostetaan tuotekehityksen aikana tuotteen ominaisuudet. Lisäksi vaatimusmäärittelyyn luotiin käyttäjäryhmät, käyttötapaukset sekä alustavat monitorointikohteet. Vaatimusten täyttämiseksi kunnonvalvontajärjestelmään on suunnitteilla myös laitetietokanta, johon sisällytetään hitsauslaitteille suoritettujen huoltojen ja validointien tiedot. Varsinaisen tuotekehitystyön alkaessa nyt laadittua vaatimusmäärittelyä tullaan käyttämään suuntaviivojen näyttäjänä projektissa.

Feasibility studies of the weldability of structural steels used in the offshore environment

The rising demand for oil and gas has made it very necessary for the oil and gas industries to explore the offshore. There is a huge resources which is available in the offshore. The search for oil and gas is faced with greater challenges because of the nature of the marine environment as it poses difficult and harsh conditions for the construction of offshore structures. The major problem of the construction of offshore structure is the ability to produce a sound weld that gives the whole structure the structural integrity needed to withstand the harsh environmental conditions. This research work presents the performance of typical offshore steels with improved weldability. The ability of reducing the carbon content of thermo-mechanically rolled steels down to 0.08% makes it possible to achieve good weldability, toughness and strength for high strength steels used in offshore applications. Importantly, the ideal welding procedure should be strictly followed as recommended. The fabrication process is as important as the welding procedure in achieving a sound weld which is free of weld defects such as hydrogen induced cracking, lamellar tearing and solidification cracking. This research work also considers the corrosion as it affects offshore structure and necessary measures to mitigate the problem caused by corrosion.

Kuparin hitsaus kattavilla laatuvaatimuksilla

Kuparin ja kupariseosten hitsaus eroaa merkittävästi esimerkiksi terästen hitsauksesta. Suuri lämmönjohtavuus, lämpölaajeneminen, pehmeneminen ja kuparin taipumus liuottaa kaasuja sulaan asettavat hitsaukselle haasteita. Kuparia on perinteisesti hitsattu kaasuhitsaamalla ja kaasukaarihitsausprosesseilla, mutta uudemmat menetelmät kuten laserhitsaus, elektronisuihkuhitsaus ja FSW-hitsaus tarjoavat uudenlaisia käyttökohteita korkealla laadulla. ISO 3834-2 asettaa noudatettavat vaatimukset hitsaustoiminnalle laatuvaatimusten ollessa kattavia. Ydinvoimalaitoksella hitsauksessa tulee lisäksi noudattaa Säteilyturvakeskuksen YVL-ohjeita, joissa on määritetty lisävaatimuksia liitosten materiaalivalinnoille, pätevöittämiselle ja tarkastamiselle. Tässä työssä tutkittiin kuparimetallien hitsauksen mahdollisuutta Loviisan ydinvoimalaitoksella juottamisen sijasta siten, että kattavat laatuvaatimukset täyttyisivät. Hitsauskokeissa ja laboratoriotutkimuksissa testattiin hitsausta erilaisilla hitsausaineilla ja hitsausprosesseilla. Koetulosten pohjalta toteutettiin hitsausmenetelmä deoksidoidun kupariputken ja tinapronssilaipan TIG-hitsaukselle.

Orbitaali-TIG-hitsauksen kehittäminen compoundputkien hitsaamisessa

Tässä työssä tutkittiin orbitaali-TIG-hitsauksen hyödyntämistä paineenalaisten compoundputkien jatkohitsien hitsaamiseen. Tutkimus tehtiin Warkaus Works Oy:n omistamalle konepajalle. Tutkimuksen tavoitteena oli laatia standardin SFS-EN ISO 15613 mukaan hyväksytty hitsausmenetelmä. Työn kirjallisuuskatsauksessa esiteltiin orbitaalihitsauksessa käytettävät hitsausprosessit ja laitteistot eri liitosmuodoille. Työssä esiteltiin myös kuumavedettyjen compoundputkien valmistusprosessia ja rakennetta. Tämän lisäksi kerrottiin putkien hitsattavuudesta ja hitsauksen esivalmisteluista, sekä käyttökohteista voimalaitoskattilassa. Ennen menetelmäkokeen hitsausta suoritettiin suuri määrä koehitsauksia yrityksen orbitaali-TIG-laitteistolla. Onnistuneiden koehitsausten perusteella laadittiin hitsausohjelma, jolla hitsattiin testiputket menetelmäkokeeseen. Hitsausmenetelmää varten valittiin Sandvikin valmistama compoundputki. Testihitseille suoritettiin rikkomattomia ja rikkovia tarkastuksia. Hyväksyttyjen tarkastusten pohjalta laadittiin hitsausmenetelmän hyväksymispöytäkirjan. Lisäksi diplomityössä verrattiin mekanisoidun hitsauksen hitsausaikaa käsinhitsauksen hitsausaikaa. Orbitaali-TIG-hitsauksen käyttäminen edellyttää hitsattavalta railolta aina mahdollisimman samanlaisen lähtötilanteen, jotta sen suoritusvarmuus saadaan mahdollisimman korkeaksi. Railon valmistamisen tarkkuudella on mahdollista saada riittävän tarkkoja railoja hitsien laadukkaaseen hitsaukseen. Hitsaus edellyttää laitteiston langansyötön ja elektrodin tarkkoja asetuksia, jotta hitsaus on laadukasta. Lisäaineen jähmeä sula ja hitsin tunkeumavaatimus hankaloittavat orbitaalihitsausta.

Effects of a postweld heat treatment on a submerged arc welded ASTM A537 pressure vessel steel

Postweld heat treatment (PWHT) is frequently applied to steel pressure vessels, following the requirements of the ASME code (section VIII), which establishes the parameters of the PWHT based on the thickness and chemical composition of the welded section. This work shows the results of an analysis undertaken on a sample of ASTM A537 C1 steel subjected to qualifying welding procedure tests including PWHT (650 degreesC/5 h), the results obtained showed that this PWHT practice promoted a reduction in the mechanical properties of the base metal and the heat-affected zone (HAZ).

Efeitos do pré-aquecimento e parâmetros de pulso sobre a microestrutura e propriedades mecânicas de solda em aço ARBL

Pós-graduação em Engenharia Mecânica - FEB

Aplicação do processo laser CO2 de soldagem em aço ARBL na fabricação de rotores para máquinas elétricas

Pós-graduação em Engenharia Mecânica - FEG

Estudo do comportamento dos aços ferramentas soldados em fadiga

Sabendo-se que a fadiga é uma redução gradual da capacidade de carga do componente pela ruptura lenta e gradual do material. E que este defeito decorre do avanço infinitesimal de microtrincas, que se formam no interior do material, imperceptível a olho nu, como também é notório que a presença dos elementos de liga nos aços, propicia alterações nas propriedades metalurgias e mecânicas no material, aplicado à obra. Por outro lado, ao ser submetido a processamentos dos mais diversos, os mesmos, deformam nas zonas elásticas, plásticas e ao fim rompem-se. Ressaltando-se o objetivo deste estudo, destina se abordar as uniões soldadas, nos estágios em que ficam sujeitas a altas temperaturas e resfriam sem controle, até a temperatura ambiente. Ao fim, são solicitados por carregamentos cíclicos constantes ou alternados. Nesta particularidade, espera-se detectar mudanças estruturais profundas na Zona Termicamente Afetada – ZTA, em razão do superaquecimento sofrido, tanto na proximidade do ponto central da poça de fusão como na região localizada na vizinhança. Como não dispomos de parâmetros suficientes e necessários ao controle destas alterações, propomos analisar a ZTA da junta soldada, com a finalidade de avaliar o comportamento metalúrgico e suas implicações causadas pelas interações gás-metal. Analisar os efeitos resultantes do triangulo formado pelo material base aço AISI/SAE 4340, SAE 1020 chanfrados em V e o eletrodo revestido E-6013. A análise da estrutura será realizada pelas técnicas de ensaio metalográfico usando o método da microscopia óptica – MO o qual é de ampla difusão nas comunicações técnicas e cientificas, através das quais, distinguirão as transformações multifásicas. Transformações estas, distintas pelas transformações das austenitas diretas em martensitas sem passar pelas ferritas e perlitas. Com estas identidades, o metalógrafo pode caracterizar e predizer as reações futuras das estruturas mediante a análise das solicitações, a que possam estar submetidas. Para analisar o comportamento em fadiga dos materiais em questão, adota-se como parâmetro auxiliar, o ensaio do pêndulo de Charpy. Portanto, pelos resultados obtidos, conclui-se que as estruturas são comprometidas por tensões internas em conseqüência fragilizam, mas o procedimento de soldagem pode ser adotado, seguido de recozimento para alivio de tensões, se não fizer trincas.

Avaliação da tenacidade à fratura em juntas soldadas circunferenciais de tubulações de processo

This work aims to analyze the toughness of a welded joint in the presence of a crack through the analysis of maximum tension the material can withstand the presence of this type of defect, since a discontinuity is likely to occur in this type of joint and its detection and its design is simple, using non-destructive testing techniques. The study will be conducted through the CTOD test - Crack-Tip Opening Displacement, with type specimens SE (B) - Single Edge Bend taken from a weld in the L-C position in relation to the length (longitudinal axis) of a test tube. The main idea is to simulate the welding conditions for the manufacture of industrial pipes, made in boiler shops (pipe-shop) within petrochemical plants. These pipes are often subject to operation with flammable and toxic subjected to high pressures and temperatures, where one can break the line can cause irreparable damage to the plant, the environment and the health of surrounding communities. With this study we evaluate whether the weld metal has the same properties as fracture toughness of the base material. This study shows the importance of using a qualified welding procedure for performing quality welds while maintaining the properties of the fracture toughness of the base metal. It was found from the results of tests using a welding procedure described for carrying out welding ensures mechanical properties very close to the base metal, which in terms of design is great, since one can ensure that the weld will the same characteristics of the base metal specified for the assembly of the pipe

Estudo das alterações das propriedades mecânicas em aço A-516 grau 70 soldado e submetido a tratamento térmico de alívio de tensões

Pressure vessels are equipments that require a great care because of their high cost and human life risk in case of fail, and its fabrication methods are different for each manufacturer. Normally, pressure vessels and its parts are fabricated by welding, which may change local properties of metals. The head of a pressure vessel is a very important structural component and it is fabricated by welding and mechanical conformation. Because its excellent mechanical properties, de steel A-516 Grade 70 is often used in manufacturing of large pressure vessels that are subjected to high pressure and temperature, but was verified that its mechanical resistance is decreased when submitted to a tension relief heat treatment. By experience it was defined that before mechanical conformation of the head of a large pressure vessel, the steel should be submitted to a stress relief heat treatment in order to facilitate the mechanical conformation, but there is no quantitative analysis to prove this method and study its possible risks. In the present work the steel A-516 Grade 70 demonstrated a decrease of its mechanical resistance when submitted to a stress relief heat treatment, but keeping above the minimum limit defined in the literature. By other side its ductility was substantially increased, being possible to deduce that the stress relief heat treatment before mechanical conformation is a viable e recommended technique, but with reservations. With the data acquired during the fabrication e preparation of the specimen and the result of the tests, it was possible to elaborate a welding procedure that provides the same results obtained in this present work

LED bulb lamps technical specification and testing procedure for solar home systems.

With the consolidation of the new solid state lighting LEOs devices, te5t1n9 the compliance 01 lamps based on this technology lor Solar Home Systems (SHS) have been analyzed. The definition of the laboratory procedures to be used with final products 15 a necessary step in arder to be able to assure the quality of the lamps prior to be installed [1]. As well as with CFL technology. particular attention has been given to simplicity and technical affordability in arder to facilitate the implementation of the test with basie and simple laboratory too15 even on the same SHS electrification program locations. The block of test procedures has been applied to a set of 14 low-cost lamps. They apply to lamp resistance, reliability and performance under normal, extreme and abnormal operating conditions as a simple but complete quality meter tool 01 any LEO bulb.

LED bulbs technical specification and testing procedure for solar home systems

The definition of technical specifications and the corresponding laboratory procedures are necessary steps in order to assure the quality of the devices prior to be installed in Solar Home Systems (SHS). To clarify and unify criteria a European project supported the development of the Universal Technical Standard for Solar Home Systems (UTSfSHS). Its principles were to generate simple and affordable technical requirements to be optimized in order to facilitate the implementation of tests with basic and simple laboratory tools even on the same SHS electrification program countries. These requirements cover the main aspects of this type of installations and its lighting chapter was developed based on the most used technology at that time: fluorescent tubes and CFLs. However, with the consolidation of the new LED solid state lighting devices, particular attention is being given to this matter and new procedures are required. In this work we develop a complete set of technical specifications and test procedures that have been designed within the frame of the UTSfSHS, based on an intense review of the scientific and technical publications related to LED lighting and their practical application. They apply to lamp reliability, performance and safety under normal, extreme and abnormal operating conditions as a simple but complete quality meter tool for any LED bulb.

Strategies for genetic model specification in the screening of genome-wide meta-analysis signals for further replication

Background Meta-analysis is increasingly being employed as a screening procedure in large-scale association studies to select promising variants for follow-up studies. However, standard methods for meta-analysis require the assumption of an underlying genetic model, which is typically unknown a priori. This drawback can introduce model misspecifications, causing power to be suboptimal, or the evaluation of multiple genetic models, which augments the number of false-positive associations, ultimately leading to waste of resources with fruitless replication studies. We used simulated meta-analyses of large genetic association studies to investigate naive strategies of genetic model specification to optimize screenings of genome-wide meta-analysis signals for further replication. Methods Different methods, meta-analytical models and strategies were compared in terms of power and type-I error. Simulations were carried out for a binary trait in a wide range of true genetic models, genome-wide thresholds, minor allele frequencies (MAFs), odds ratios and between-study heterogeneity (tau(2)). Results Among the investigated strategies, a simple Bonferroni-corrected approach that fits both multiplicative and recessive models was found to be optimal in most examined scenarios, reducing the likelihood of false discoveries and enhancing power in scenarios with small MAFs either in the presence or in absence of heterogeneity. Nonetheless, this strategy is sensitive to tau(2) whenever the susceptibility allele is common (MAF epsilon 30%), resulting in an increased number of false-positive associations compared with an analysis that considers only the multiplicative model. Conclusion Invoking a simple Bonferroni adjustment and testing for both multiplicative and recessive models is fast and an optimal strategy in large meta-analysis-based screenings. However, care must be taken when examined variants are common, where specification of a multiplicative model alone may be preferable.