Valorización de cenizas de lodo de depuradora como componente de hormigones para prefabricados

Se plantea la combinación binaria y ternaria de cenizas de lodo de depuradora (CLD) con ceniza volante, polvo de mármol y ceniza de cáscara de arroz, como sustitución parcial o como adición respecto al cemento Portland en hormigones, con una dosificación similar a la utilizada en la prefabricación de bloques (consistencia muy seca). Se llevaron a cabo ensayos físico-mecánicos sobre probetas de mortero y hormigón con edades de curado de 28 y 90 días: densidad, absorción y resistencia a compresión. Se comprueba que la sustitución de cemento por CLD supone una disminución de la densidad y de la resistencia respecto a la muestra patrón, sin embargo, las combinaciones con otros residuos mejoran notablemente las características de los materiales cementantes. La adición de CLD proporcionó densidades y resistencias similares a la muestra de control y reduce significativamente la absorción de agua.

Energy conversion assessment of vacuum, slow and fast pyrolysis processes for low and high ash paper waste sludge

The performance of vacuum, slow and fast pyrolysis processes to transfer energy from the paper waste sludge (PWS) to liquid and solid products was compared. Paper waste sludges with low and high ash content (8.5 and 46.7 wt.%) were converted under optimised conditions for temperature and pellet size to maximise both product yields and energy content. Comparison of the gross energy conversions, as a combination of the bio-oil/tarry phase and char (ECsum), revealed that the fast pyrolysis performance was between 18.5% and 20.1% higher for the low ash PWS, and 18.4% and 36.5% higher for high ash PWS, when compared to the slow and vacuum pyrolysis processes respectively. For both PWSs, this finding was mainly attributed to higher production of condensable organic compounds and lower water yields during FP. The low ash PWS chars, fast pyrolysis bio-oils and vacuum pyrolysis tarry phase products had high calorific values (∼18-23 MJ kg-1) making them promising for energy applications. Considering the low calorific values of the chars from alternative pyrolysis processes (∼4-7 MJ kg-1), the high ash PWS should rather be converted to fast pyrolysis bio-oil to maximise the recovery of usable energy products.

Precipitation of heavy metals from wastewater using simulated flue gas: sequent additions of fly ash, lime and carbon dioxide

Lime is a preferred precipitant for the removal of heavy metals from industrial wastewater due to its relatively low cost. To reduce heavy metal concentration to an acceptable level for discharge, in this work, fly ash was added as a seed material to enhance lime precipitation and the suspension was exposed to CO2 gas. The fly ash-lime-carbonation treatment increased the particle size of the precipitate and significantly improved sedimentation of sludge and the efficiency of heavy metal removal. The residual concentrations of chromium, copper, lead and zinc in effluents can be reduced to (mg L-1) 0.08, 0.14, 0.03 and 0.45, respectively. Examination of the precipitates by XRD and thermal analysis techniques showed that calcium-heavy metal double hydroxides and carbonates were present. The precipitate agglomerated and hardened naturally, facilitating disposal without the need for additional solidification/stabilization measures prior to landfill. It is suggested that fly ash, lime and CO2, captured directly from flue gas, may have potential as a method for wastewater treatment. This method could allow the ex-situ sequestration of CO2, particularly where flue-gas derived CO2 is available near wastewater treatment facilities. (C) 2009 Elsevier Ltd. All rights reserved.

Influence of carbonation on the acid neutralization capacity of cements and cement-solidified/stabilized electroplating sludge

Portland cement (PC) and blended cements containing pulverized fuel ash (PFA) or granulated blast-furnace slag (GGBS) were used to solidify/stabilize an electroplating sludge in this work. The acid neutralization capacity (ANC) of the hydrated pastes increased in the order of PC > PC/GGBS > PC/PFA. The GGBS or PFA replacement (80 wt%) reduced the ANC of the hydrated pastes by 30–50%. The ANC of the blended cement-solidified electroplating sludge (cement/sludge 1:2) was 20–30% higher than that of the hydrated blended cement pastes. Upon carbonation, there was little difference in the ANC of the three cement pastes, but the presence of electroplating sludge (cement/sludge 1:2) increased the ANC by 20%. Blended cements were more effective binders for immobilization of Ni, Cr and Cu, compared with PC, whereas Zn was encapsulated more effectively in the latter. Accelerated carbonation improved the immobilization of Cr, Cu and Zn, but not Ni. The geochemical code PHREEQC, with the edited database from EQ3/6 and HATCHES, was used to calculate the saturation index and solubility of likely heavy metal precipitates in cement-based solidification/stabilization systems. The release of heavy metals could be related to the disruption of cement matrices and the remarkable variation of solubility of heavy metal precipitates at different pH values.

Bauxite residue (Red mud) as a pulverised fuel ash substitute in the manufacture of lightweight aggregate

This study looked at the potential of bauxite residue or red mud to be used in the manufacture of lightweight aggregate in replacement of pulverised fuel ash (PFA), commonly used as a way of recycling problematic wastes. The percentage replacements of red mud with PFA were as follows: 25, 31, 38, 44 and 50%. These were blended in a mix with waste excavated clay and sewage sludge – all from the Chongqing municipality in China. Lightweight pellets were produced using a Trefoil rotary kiln and were sintered to 1200 °C. Results showed that 44 % bauxite residue replacement produced lightweight pellets with the highest compressive strength, highest density and largest water holding capacity. This would be expected in materials with a low level of silicates, which causes insufficient glass phase viscosity and therefore poor bloating during firing; producing an aggregate with a higher density but with open pores that allowed for larger water absorption. All ratios of red mud aggregates were significantly reduced in pH after firing to around pH 8, and this reduced the leachability of the aggregates to levels below those set by the European landfill directive (2003/33/EC).

Study of the pozzolanic reaction kinetics in sugar cane bagasse-clay ash/calcium hydroxide system: kinetic parameters and pozzolanic activity

This paper presents a study of the pozzolanic reaction kinetics between calcium hydroxide and a mixture of sugar cane bagasse with 20 and 30% of clay, burned at 800 and 1000 degrees C (SCBCA) by electrical conductivity measurements. A kinetic-diffusive model produced in previous studies by some of the authors was used. The model was fitted to the experimental data, which allowed the computation of the kinetic parameters of the pozzolanic reaction (reaction rate constant and free energy of activation) that rigorously characterised the pozzolanic activity of the materials. The results show that SCBCA demonstrated reactivity and good pozzolanic qualities in the range 800-1000 degrees C.

Evaluation by respirometry of the degradability of retort water using a shale ash and overburden packed column

Oil shale processing produces an aqueous wastewater stream known as retort water. The fate of the organic content of retort water from the Stuart oil shale project (Gladstone, Queensland) is examined in a proposed packed bed treatment system consisting of a 1:1 mixture of residual shale from the retorting process and mining overburden. The retort water had a neutral pH and an average unfiltered TOC of 2,900 mg l(-1). The inorganic composition of the retort water was dominated by NH4+. Only 40% of the total organic carbon (TOC) in the retort water was identifiable, and this was dominated by carboxylic acids. In addition to monitoring influent and effluent TOC concentrations, CO2 evolution was monitored on line by continuous measurements of headspace concentrations and air flow rates. The column was run for 64 days before it blocked and was dismantled for analysis. Over 98% of the TOC was removed from the retort water. Respirometry measurements were confounded by CO2 production from inorganic sources. Based on predictions with the chemical equilibrium package PHREEQE, approximately 15% of the total CO2 production arose from the reaction of NH4+ with carbonates. The balance of the CO2 production accounted for at least 80% of the carbon removed from the retort water. Direct measurements of solid organic carbon showed that approximately 20% of the influent carbon was held-up in the top 20cm of the column. Less than 20% of this held-up carbon was present as either biomass or as adsorbed species. Therefore, the column was ultimately blocked by either extracellular polymeric substances or by a sludge that had precipitated out of the retort water.

Mixing and drying mud and ash at Tully Mill

Disposal of mud and ash, particularly in wet weather conditions, is a significant expense for mills. This paper reports on part of a process to pelletise mud and ash, aimed at making mud and ash more attractive to growers across entire mill districts. The full process and the re-constituting and centrifuging rotary vacuum filter mud part of the process were described in two papers to the 2011 conference. The component described in this paper involves aspects of mixing mud and ash with subsequent drying using boiler exit gas. The mud material needs to mix easily with boiler ash and the mixture has to feed easily into and be pneumatically conveyed by a flue gas dryer. The performance of a pilot flue gas dryer for drying mud and ash was evaluated. The mud and ash mixture was found to dry much faster than final bagasse, provided the mud and ash material was broken up into individual particles. A previously developed computer model of bagasse drying was updated to take into account the smaller particle size of the mud and ash mixture. This upgraded model predicted the performance of the pilot flue gas dryer well.

The Ash Burner

Growing up with his father in a small coastal town, all Ted knows about his mother is that she died when he was a boy. His father has brought them halfway across the world to start anew, but her absence defines and haunts their lives. When Ted meets Anthony and Claire, an intense friendship begins, carrying them to Sydney and university. They introduce him to poetry and art, and he feels a sense of belonging at last. But as the trio’s friendship deepens over the years, Ted must learn to negotiate the boundaries of love, and come to terms with a legacy of secrets and silence. Written with extraordinary grace and sensitivity, The Ash Burner explores beauty and desire, grief and loss, and the search for one’s true self.