990 resultados para Volume total de carga levantada


Relevância:

100.00% 100.00%

Publicador:

Resumo:

Ceramic composites produced with polymerics precursors have been studied for many years, due to the facility of obtaining a complex shape, at low temperature and reduces cost. The main objective of this work is to study the process of sintering of composites of ceramic base consisting of Al2O3 and silicates, reinforced for NbC, through the technique of processing AFCOP, as well as the influence of the addition of LZSA, ICZ and Al as materials infiltration in the physical and mechanical properties of the ceramic composite. Were produced ceramic matrix composites based SiCxOy e Al2O3 reinforced with NbC, by hidrosilylation reaction between D4Vi and D1107 mixtured with Al2O3 as inert filler, Nb and Al as reactive filler. The specimens produced were pyrolised at 1200, 1250 and 1400°C and infiltred with Al, ICZ and LZSA, respectively. Density, porosity, flexural mechanical strength and fracture surface by scanning electron microscopy were evaluated. The microstructure of the composites was investigated by X-ray diffraction to identify the presence of crystalline phases. The composites presented apparent porosity varying of 31 up to 49% and mechanical flexural strength of 14 up to 34 MPa. The infiltration process improviment of the densification and reduction of the porosity, as well as increased the values of mechanical flexural strength. The obtained phases had been identified as being Al3Nb, NbSi2, Nb5S3, Nb3Si and NbC. The samples that were submitted the infiltration process presented a layer next surface with reduced pores number in relation to the total volume

Relevância:

100.00% 100.00%

Publicador:

Resumo:

In this work, were produced ceramic matrix composites based in SiCxOy e Al2O3 reinforced with NbC, by hydrosilylation reaction between D4Vi and poly(methylhydrosiloxane) mixtured with Al2O3 as inert filler, Nb and Al as reactive filler. After the mixture and compactation at 80ºC (warm pressing), the samples were pyrolised at 1200 and 1400ºC and infiltred with ICZ and LZSA respectively, and thermically, physical and structurally characterized by X-ray diffraction, density and porosity, flexural mechanical strength and fracture surface by scanning electron microscopy. The yield ceramic obtained after pyrolysis for studied composition at 1200ºC was 95%. The obtained phases had been identified as being Al3Nb, NbSi2 and NbC. The composite material presented apparent porosity varying of 15 up to 32% and mechanical flexural strenght of 32 up to 37,5MPa. After the fracture surface analysis, were observed a phases homogeneous dispersion, with some domains of amorphous and crystalline aspect. The samples that were submitted the infiltration cycle presented a layer next the surface with reduced pores number in relation to the total volume

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The prescription of strength training intensity (ST) by maximum repetition (RM) is characterized by a decrease in the number of repetitions in multiple series. Some studies have shown that reductions in the intensity of exercise can optimize the volume of training with similar acute neuromuscular behaviors. The objective of the study was to investigate the acute effect of two different ST intensities on the training volume, maximum voluntary contraction (MVC) and rate of force development (RFD) in elderly women. The study included eight trained women (66.7 ± 6.7 years; 7.6 ± 17.8 kg; 159 cm; 29.33 ± 5.80 kg/m²). They underwent to three experimental conditions: two different intensities of ST (100% and 80% of 15-RM) on a chair for Leg Extension and a control condition. In the condition to 100% of 15 RM, all participants performed three sets to the concentric muscle fatigue, whereas in the condition to 80% involved the use of two sets of 15 repetitions and only the third to the concentric muscle fatigue. The order of experimental conditions was randomized. The MVC and RFD were determined on the basis of the isometric forcetime curve analysis which was obtained by a force transducer fixed on the unit Bonnet Chair, in the pre and after four and ten minutes for each experimental conditions. The total volume was calculated by multiplying the number of repetitions in three sets by the load in kg. Descriptive statistical analysis procedures were employed (mean ± standard deviation) in addition to two-way ANOVA. The level of significance was set at p <0.05. It was neither main effect of moment or condition, nor condition x moment interaction for MVC and RFD. For the total volume, no significant difference was noted between the conditions (100 and 80% of 15-RM). For sustainability of ...(Complete abstract click electronic access below)

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Apesar da literatura sobre anestesia em equinos ser ampla, referências sobre técnicas e fármacos anestésicos em muares são escassas. Nesse contexto objetivou-se relatar o caso de uma mula com um ano e meio de idade, fêmea, pesando 232 Kg, que foi atendida no Hospital Veterinário da UNESP de Araçatuba no dia com queixa de ferida granulomatosa no membro torácico direito, na região da quartela. Ao exame físico o animal apresentava frequência cardíaca (FC) de 56 batimentos por minuto (bpm), respiratória (f) de 44 movimentos por minuto (mpm), temperatura retal de 38,1 (T°), mucosas róseas e tempo de preenchimento capilar (TPC) de dois segundos. A ferida apresentava-se com tecido de granulação exuberante, em que a remoção cirúrgica foi indicada. O hemograma completo foi realizado antes da cirurgia, não apresentando alterações significativas. Como medicação pré-anestésica (MPA) utilizou-se xilazina 2% (0,5 mg/Kg/IV) associada com Acepromazina 1% (0,05 mg/Kg/IV). Em seguida, foi feita a indução anestésica com Cetamina 10% (2 mg/kg/IV) e Midazolam 0,5% (0,05 mg/kg/IV). Concomitantimente, foi realizado o bloqueio do nervo sesamóide abaxial lateral e medial com 5 ml de Lidocaína 2% em cada ponto. A cirurgia foi realizada com o animal em decúbito lateral esquerdo, empregando-se anestesia total intavenosa (TIVA), empregando-se a associação do Éter Gliceril Guaiacol (EGG) 5%, Xilazina 2% (1mg/ML) e Cetamina 10% (2 mg/ML). O volume total infundido, totalizando duas bolsas de 250 ml, foi administrado em uma hora e meia de cirurgia. O paciente manteve-se estável durante toda a cirurgia e foi continuamente monitorado quanto a profundidade anestésica por meio dos estágios e planos de Guedel, bem como com a mensuração das frequências cardíaca (FC), que se manteve entre 35 a 40 bpm e respiratória (f) mantida entre 25 a 28 mpm. Ao termino do procedimento cirúrgico o paciente permaneceu assistido durante toda a recuperação, sendo essa tranquila e de boa qualidade, com o paciente assumindo a posição quadrupedal em 15 minutos. A técnica anestésica empregada foi adequada, eficiente e se mostrou viável para realização de cirurgias a campo em muares.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Relevância:

100.00% 100.00%

Publicador:

Resumo:

A pressurized core with CH4 hydrate or dissolved CH4 should evolve gas volumes in a predictable manner as pressure is released over time at isothermal conditions. Incremental gas volumes were collected as pressure was released over time from 29 pressure core sampler (PCS) cores from Sites 994, 995, 996, and 997 on the Blake Ridge. Most of these cores were kept at or near 0ºC with an ice bath, and many of these cores yielded substantial quantities of CH4. Volume-pressure plots were constructed for 20 of these cores. Only five plots conform to expected volume and pressure changes for sediment cores with CH4 hydrate under initial pressure and temperature conditions. However, other evidence suggests that sediment in these five and at least five other PCS cores contained CH4 hydrate before core recovery and gas release. Detection of CH4 hydrate in a pressurized sediment core through volume-pressure relationships is complicated by two factors. First, significant quantities of CH4-poor borehole water fill the PCS and come into contact with the core. This leads to dilution of CH4 concentration in interstitial water and, in many cases, decomposition of CH4 hydrate before a degassing experiment begins. Second, degassing experiments were conducted after the PCS had equilibrated in an ice-water bath (0ºC). This temperature is significantly lower than in situ values in the sediment formation before core recovery. Our results and interpretations for PCS cores collected on Leg 164 imply that pressurized containers formerly used by the Deep Sea Drilling Project (DSDP) and currently used by ODP are not appropriately designed for direct detection of gas hydrate in sediment at in situ conditions through volume-pressure relationships.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Ceramic composites produced with polymerics precursors have been studied for many years, due to the facility of obtaining a complex shape, at low temperature and reduces cost. The main objective of this work is to study the process of sintering of composites of ceramic base consisting of Al2O3 and silicates, reinforced for NbC, through the technique of processing AFCOP, as well as the influence of the addition of LZSA, ICZ and Al as materials infiltration in the physical and mechanical properties of the ceramic composite. Were produced ceramic matrix composites based SiCxOy e Al2O3 reinforced with NbC, by hidrosilylation reaction between D4Vi and D1107 mixtured with Al2O3 as inert filler, Nb and Al as reactive filler. The specimens produced were pyrolised at 1200, 1250 and 1400°C and infiltred with Al, ICZ and LZSA, respectively. Density, porosity, flexural mechanical strength and fracture surface by scanning electron microscopy were evaluated. The microstructure of the composites was investigated by X-ray diffraction to identify the presence of crystalline phases. The composites presented apparent porosity varying of 31 up to 49% and mechanical flexural strength of 14 up to 34 MPa. The infiltration process improviment of the densification and reduction of the porosity, as well as increased the values of mechanical flexural strength. The obtained phases had been identified as being Al3Nb, NbSi2, Nb5S3, Nb3Si and NbC. The samples that were submitted the infiltration process presented a layer next surface with reduced pores number in relation to the total volume

Relevância:

100.00% 100.00%

Publicador:

Resumo:

This work was carried out with the objective of studying the spatial variability of the physical attributes of a Red-Yellow Ultisol under pasture and secondary vegetation in natural regeneration. Two areas were chosen in a hillside, with the soil sampling to the depth of 0-0.2 m, with the georeferenced points in a regular grid of 10x10 m, totalizing 64 points. In each point it was evaluated the total volume of porosity, macroporosity, microporosity, bulk density, soil penetration resistance and soil water content. The studied attributes in the pasture area present indicator of soil compaction for the animals' traffic, with moderate and strong structure of spatial dependence, except for the macroporosity and penetration resistance. In the area of secondary vegetation (VN) only the macroporosity does not present spatial dependence. The total volume of porosity and the bulk density present the same spatial standard in the area under pasture.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Universidade Estadual de Campinas . Faculdade de Educação Física

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Stellate ganglion (SG) represents the main sympathetic input to the heart. This study aimed at investigating physical exercise-related changes in the quantitative aspects of SG neurons in treadmill-exercised Wistar rats. By applying state-of-the-art design-based stereology, the SG volume, total number of SG neurons, mean perikaryal volume of SG neurons, and the total volume of neurons in the whole SG have been examined. Arterial pressure and heart rate were also measured at the end of the exercise period. The present study showed that a low-intensity exercise training program caused a 12% decrease in the heart rate of trained rats. In contrast, there were no effects on systolic pressure, diastolic pressure, or mean arterial pressure. As to quantitative changes related to physical exercise, the main findings were a 21% increase in the fractional volume occupied by neurons in the SG, and an 83% increase in the mean perikaryal volume of SG neurons in treadmill-trained rats, which shows a remarkable neuron hypertrophy. It seems reasonable to infer that neuron hypertrophy may have been the result of a functional overload imposed on the SG neurons by initial posttraining sympathetic activation. From the novel stereological data we provide, further investigations are needed to shed light on the mechanistic aspect of neuron hypertrophy: what role does neuron hypertrophy play? Could neuron hypertrophy be assigned to the functional overload induced by physical exercise? (C) 2008 Wiley-Liss, Inc.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Objetivo: Analisar a padronização da coleta do lavado gástrico para diagnóstico de tuberculose em crianças. Métodos: Estudo de revisão sistemática referente aos anos de 1968 a 2008. O levantamento de artigos científicos foi feito nas bases de dados Lilacs, SciELO e Medline, utilizando-se a estratégia de busca ("gastric lavage and tuberculosis" ou "gastric washing and tuberculosis", com o limite "crianças com idade até 15 anos"; e "gastric lavage and tuberculosis and childhood" ou "gastric washing and tuberculosis and childhood"). A análise dos 80 artigos recuperados baseou-se nas informações sobre o protocolo de coleta de lavado gástrico para diagnóstico da tuberculose em crianças: preparo da criança e horas de jejum, horário da coleta, aspiração do resíduo gástrico, volume total aspirado, solução usada para aspiração do conteúdo gástrico, solução descontaminante, solução tampão, e tempo de encaminhamento das amostras para o laboratório. Desses, foram selecionados 14 artigos após análise criteriosa. Resultados: Nenhum artigo explicava detalhadamente todo o procedimento. Em alguns artigos não constavam: quantidade de aspirado gástrico, aspiração antes ou após a instilação de uma solução, solução usada na aspiração gástrica, solução tampão utilizada, tempo de espera entre coleta e processamento do material. Esses resultados mostram inconsistências entre os protocolos de coleta de lavado gástrico. Conclusões: Embora este seja um método secundário no Brasil, reservado a casos que não alcançaram pontuação diagnóstica pelo sistema preconizado pelo Ministério da Saúde, é necessário padronizar a coleta de lavado gástrico para diagnóstico de tuberculose pulmonar na infância.