Subsurface urban heat island and its effects on horizontal ground-source heat pump potential under climate change

Recent urban air temperature increase is attributable to the climate change and heat island effects due to urbanization. This combined effects of urbanization and global warming can penetrate into the underground and elevate the subsurface temperature. In the present study, over-100 years measurements of subsurface temperature at a remote rural site were analysed, and an increasing rate of 0.17⁰C per decade at soil depth of 30cm due to climate change was identified in the UK, but the subsurface warming in an urban site showed a much higher rate of 0.85⁰C per decade at a 30cm depth and 1.18⁰C per decade at 100cm. The subsurface urban heat island (SUHI) intensity obtained at the paired urban-rural stations in London showed an unique 'U-shape', i.e. lowest in summer and highest during winter. The maximum SUHII is 3.5⁰C at 6:00 AM in December, and the minimum UHII is 0.2⁰C at 18:00PM in July. Finally, the effects of SUHI on the energy efficiency of the horizontal ground source heat pump (GSHP) were determined. Provided the same heat pump used, the installation at an urban site will maintain an overall higher COP compared with that at a rural site in all seasons, but the highest COP improvement can be achieved in winter.

The urban cool island phenomenon in a high-rise high-density city and its mechanisms

The urban heat island (UHI) phenomenon has been studied extensively, but there are relatively fewer reports on the so-called urban cool island (UCI) phenomenon. We reveal here that the UCI phenomenon exists in Hong Kong during the day, and is associated with the UHI at night under all wind and cloud conditions. The possible mechanisms for the UCI phenomenon in such a high-rise compact city have been discovered using a lumped urban air temperature model. A new concept of urban cool island degree hours (UCIdh) to measure the UCI intensity and duration is proposed. Our analyses reveal that when anthropogenic heat is small or absent, a high-rise and high-density city experiences a significant daytime UCI effect. This is explained by an intensified heat storage capacity and the reduced solar radiation gain of urban surfaces. However, if anthropogenic heat in the urban area increases further, the UCI phenomenon still exists, yet UCIdh decrease dramatically in a high-rise compact city. In a low-rise, low-density city, the UCI phenomenon also occurs when there is no anthropogenic heat, but easily disappears when there is little anthropogenic heat, and the UHI phenomenon dominates. This probably explains why the UHI phenomenon is often observed, but the UCI phenomenon is rarely observed. The co-existence of urban heat/cool island phenomena implies reduction of the daily temperature range (DTR) in such cities, and its dependence on urban morphology also implies that urban morphology can be used to control the urban thermal environment.

Using phenology to assess urban heat islands in tropical and temperate regions

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Heat island simulations in Londrina city, Brazil

This work aims to study the urban heat island on North region of Parana state, Brazil and the influence of land use and urban settlements on the intensity and frequency of occurrence of these events. Through atmospheric modeling whith WRF/Chem model two simulations were made with different land and use files, one with the original land use another obtained from a composition of MODIS-Landsat imagery. The simulations showed good skills compared to observed data. Urban areas presented higher temperatures. Landsat land use has represented better urban heat islands (UHI), the gradient between urban and rural areas was well demonstrated and the correlation coefficient was above 0.92. The model underestimated the maximum values and overestimated the minimum compared with observed data in both simulations.

Surface thermal analysis of North Brabant cities and neighbourhoods during heat waves

The urban heat island effect is often associated with large metropolises. However, in the Netherlands even small cities will be affected by the phenomenon in the future (Hove et al., 2011), due to the dispersed or mosaic urbanisation patterns in particularly the southern part of the country: the province of North Brabant. This study analyses the average night time land surface temperature (LST) of 21 North-Brabant urban areas through 22 satellite images retrieved by Modis 11A1 during the 2006 heat wave and uses Landsat 5 Thematic Mapper to map albedo and normalized difference temperature index (NDVI) values. Albedo, NDVI and imperviousness are found to play the most relevant role in the increase of nighttime LST. The surface cover cluster analysis of these three parameters reveals that the 12 “urban living environment” categories used in the region of North Brabant can actually be reduced to 7 categories, which simplifies the design guidelines to improve the surface thermal behaviour of the different neighbourhoods thus reducing the Urban Heat Island (UHI) effect in existing medium size cities and future developments adjacent to those cities.

Evaluating green infrastructure in urban environments using a multi-taxa and functional diversity approach

Forested areas within cities host a large number of species, responsible for many ecosystem services in urban areas. The biodiversity in these areas is influenced by human disturbances such as atmospheric pollution and urban heat island effect. To ameliorate the effects of these factors, an increase in urban green areas is often considered sufficient. However, this approach assumes that all types of green cover have the same importance for species. Our aim was to show that not all forested green areas are equal in importance for species, but that based on a multi-taxa and functional diversity approach it is possible to value green infrastructure in urban environments. After evaluating the diversity of lichens, butterflies and other-arthropods, birds and mammals in 31 Mediterranean urban forests in south-west Europe (Almada, Portugal), bird and lichen functional groups responsive to urbanization were found. A community shift (tolerant species replacing sensitive ones) along the urbanization gradient was found, and this must be considered when using these groups as indicators of the effect of urbanization. Bird and lichen functional groups were then analyzed together with the characteristics of the forests and their surroundings. Our results showed that, contrary to previous assumptions, vegetation density and more importantly the amount of urban areas around the forest (matrix), are more important for biodiversity than forest quantity alone. This indicated that not all types of forested green areas have the same importance for biodiversity. An index of forest functional diversity was then calculated for all sampled forests of the area. This could help decision-makers to improve the management of urban green infrastructures with the goal of increasing functionality and ultimately ecosystem services in urban areas.

Estimation of Effective Impervious Surface Area of Cochin using Satellite Images

Urbanization refers to the process in which an increasing proportion of a population lives in cities and suburbs. Urbanization fuels the alteration of the Land use/Land cover pattern of the region including increase in built-up area, leading to imperviousness of the ground surface. With increasing urbanization and population pressures; the impervious areas in the cities are increasing fast. An impervious surface refers to an anthropogenic ally modified surface that prevents water from infiltrating into the soil. Surface imperviousness mapping is important for the studies related to water cycling, water quality, soil erosion, flood water drainage, non-point source pollution, urban heat island effect and urban hydrology. The present study estimates the Total Impervious Area (TIA) of the city of Kochi using high resolution satellite image (LISS IV, 5m. resolution). Additionally the study maps the Effective Impervious Area (EIA) by coupling the capabilities of GIS and Remote Sensing. Land use/Land cover map of the study area was prepared from the LISS IV image acquired for the year 2012. The classes were merged to prepare a map showing pervious and impervious area. Supervised Maximum Likelihood Classification (Supervised MLC),which is a simple but accurate method for image classification, is used in calculating TIA and an overall classification accuracy of 86.33% was obtained. Water bodies are 100% pervious, whereas urban built up area are 100% impervious. Further based on percentage of imperviousness, the Total Impervious Area is categorized into various classes

Energy efficient building design

This chapter covers the basic concepts of passive building design and its relevant strategies, including passive solar heating, shading, natural ventilation, daylighting and thermal mass. In environments with high seasonal peak temperatures and/or humidity (e.g. cities in temperate regions experiencing the Urban Heat Island effect), wholly passive measures may need to be supplemented with low and zero carbon technologies (LZCs). The chapter also includes three case studies: one residential, one demonstrational and one academic facility (that includes an innovative passive downdraught cooling (PDC) strategy) to illustrate a selection of passive measures.

British container breeding mosquitoes: the impact of urbanisation and climate change on community composition and phenology

The proliferation of artificial container habitats in urban areas has benefitted urban adaptable mosquito species globally. In areas where mosquitoes transmit viruses and parasites, it can promote vector population productivity and fuel mosquito-borne disease outbreaks. In Britain, storage of water in garden water butts is increasing, potentially expanding mosquito larval habitats and influencing population dynamics and mosquito-human contact. Here we show that the community composition, abundance and phenology of mosquitoes breeding in experimental water butt containers were influenced by urbanisation. Mosquitoes in urban containers were less species-rich but present in significantly higher densities (100.4±21.3) per container than those in rural containers (77.7±15.1). Urban containers were dominated by Culex pipiens (a potential vector of West Nile Virus [WNV]) and appear to be increasingly exploited by Anopheles plumbeus (a human-biting potential WNV and malaria vector). Culex phenology was influenced by urban land use type, with peaks in larval abundances occurring earlier in urban than rural containers. Among other factors, this was associated with an urban heat island effect which raised urban air and water temperatures by 0.9°C and 1.2°C respectively. Further increases in domestic water storage, particularly in urban areas, in combination with climate changes will likely alter mosquito population dynamics in the UK.

Emergy-based sustainability assessment of different energy options for green buildings

It is necessary to minimize the environmental impact and utilize natural resources in a sustainable and efficient manner in the early design stage of developing an environmentally-conscious design for a heating, ventilating and air-conditioning system. Energy supply options play a significant role in the total environmental load of heating, ventilating and air-conditioning systems. To assess the environmental impact of different energy options, a new method based on Emergy Analysis is proposed. Emergy Accounting, was first developed and widely used in the area of ecological engineering, but this is the first time it has been used in building service engineering. The environmental impacts due to the energy options are divided into four categories under the Emergy Framework: the depletion of natural resources, the greenhouse effect (carbon dioxide equivalents), the chemical rain effect (sulphur dioxide equivalents), and anthropogenic heat release. The depletion of non-renewable natural resources is indicated by the Environmental Load Ratio, and the environmental carrying capacity is developed to represent the environmental service to dilute the pollutants and anthropogenic heat released. This Emergy evaluation method provides a new way to integrate different environmental impacts under the same framework and thus facilitates better system choices. A case study of six different kinds of energy options consisting of renewable and non-renewable energy was performed by using Emergy Theory, and thus their relative environmental impacts were compared. The results show that the method of electricity generation in energy sources, especially for electricity-powered systems, is the most important factor to determine their overall environmental performance. The direct-fired lithium-bromide absorption type consumes more non-renewable energy, and contributes more to the urban heat island effect compared with other options having the same electricity supply. Using Emergy Analysis, designers and clients can make better-informed, environmentally-conscious selections of heating, ventilating and air-conditioning systems.

Energy savings in buildings or UHI mitigation? Comparison between green roofs and cool roofs

The intensification of the Urban Heat Island effect (UHI) is a problem that involves several fields, and new adequate solutions are required to mitigate its amplitude. The construction sector is strictly related with this phenomenon; in particular, roofs are the envelope components subject to the highest solar irradiance, hence any mitigation strategy should start from them and involve their appropriate design process. For this purpose, cool materials, i.e. materials which are able to reflect a large amount of solar radiation and avoid overheating of building surfaces have been deeply analyzed in the last years both at building and urban scales, showing their benefits especially in hot climates. However, green roofs also represent a possible way to cope with UHI, even if their design is not straightforward and requires taking into account many variables, strictly related with the local climatic conditions. In this context, the present paper proposes a comparison between cool roofs and green roofs for several Italian cities that are representative of different climatic conditions. In search of the most effective solution, the answers may be different depending on the perspective that leads the comparison, i.e. the need to reduce the energy consumption in buildings or the desire to minimize the contribution of the UHI effect.

La prise en compte de l’adaptation au changement climatique dans les politiques publiques de verdissement (2005-2015) : le cas de Montréal

Les connaissances scientifiques sur le changement climatique (CC) évoluent rapidement. Toutefois, des incertitudes persistent sur l’étendue de ses conséquences, particulièrement dans les milieux urbains, qui subiront des impacts différents de ceux vécus par les milieux ruraux. Les autorités publiques ont récemment commencé à élaborer des politiques publiques d’adaptation au changement climatique (ACC) qui visent à en limiter les conséquences indésirables. En milieu urbain, la littérature suggère qu’un des outils que devraient privilégier ces politiques est le verdissement. Des auteurs signalent que les actions visant l’ACC peuvent se greffer dans des politiques existantes. L’ACC, comme enjeu public, peut donc être réalisée par l’entremise de sa prise en compte dans les politiques publiques de verdissement. Cette prise en compte devrait affecter le contenu (quoi?) et le pilotage (comment?) des différentes étapes des politiques. Le cas de la politique publique de verdissement de la Ville de Montréal, au Québec, nous a permis d’étudier cette prise en compte. En utilisant un cadre d’analyse des politiques publiques développé par Knoepfel et al. (2015), qui porte entre autres sur la mobilisation des ressources par différents acteurs concernés par ces politiques, nous montrons que cette dernière s’est opérée de quelques façons. Premièrement, il y a eu un changement dans l’argumentaire pour le verdissement, outil qui vise à lutter contre les îlots de chaleur urbains et assurer une meilleure gestion des eaux pluviales. Ensuite, le choix de l’échelle d’agglomération pour la prise en compte de l’ACC a entraîné un changement d’échelle dans la gestion du verdissement. La publication d’un plan d’action majeur de verdissement urbain pour l’agglomération, et dont le leitmotiv est l’ACC, le démontre. Quelques modifications réglementaires et l’inclusion de nouveaux acteurs dans la politique témoignent aussi que la prise en compte a eu lieu. Finalement, le plan d’action fournit un cadre pour la mise en œuvre du verdissement dans les zones les plus vulnérables au CC en plus d’une structure de partage des coûts. Cependant, la mise en oeuvre du verdissement dans une visée d’ACC n'a pas été évaluée dans la présente étude. Nous avons aussi noté que la biodiversité est un enjeu d’importance qui va de pair avec l’ACC dans la politique de verdissement. Il y a donc une prise en compte, partielle, de l’ACC dans la politique publique de verdissement à Montréal (avec certains écueils). Nous arguons que l’enjeu de l’ACC sert peut-être d’argument supplémentaire pour verdir la ville plutôt que d’être un véritable moteur de transformation de la politique de verdissement.

La prise en compte de l’adaptation au changement climatique dans les politiques publiques de verdissement (2005-2015) : le cas de Montréal

Les connaissances scientifiques sur le changement climatique (CC) évoluent rapidement. Toutefois, des incertitudes persistent sur l’étendue de ses conséquences, particulièrement dans les milieux urbains, qui subiront des impacts différents de ceux vécus par les milieux ruraux. Les autorités publiques ont récemment commencé à élaborer des politiques publiques d’adaptation au changement climatique (ACC) qui visent à en limiter les conséquences indésirables. En milieu urbain, la littérature suggère qu’un des outils que devraient privilégier ces politiques est le verdissement. Des auteurs signalent que les actions visant l’ACC peuvent se greffer dans des politiques existantes. L’ACC, comme enjeu public, peut donc être réalisée par l’entremise de sa prise en compte dans les politiques publiques de verdissement. Cette prise en compte devrait affecter le contenu (quoi?) et le pilotage (comment?) des différentes étapes des politiques. Le cas de la politique publique de verdissement de la Ville de Montréal, au Québec, nous a permis d’étudier cette prise en compte. En utilisant un cadre d’analyse des politiques publiques développé par Knoepfel et al. (2015), qui porte entre autres sur la mobilisation des ressources par différents acteurs concernés par ces politiques, nous montrons que cette dernière s’est opérée de quelques façons. Premièrement, il y a eu un changement dans l’argumentaire pour le verdissement, outil qui vise à lutter contre les îlots de chaleur urbains et assurer une meilleure gestion des eaux pluviales. Ensuite, le choix de l’échelle d’agglomération pour la prise en compte de l’ACC a entraîné un changement d’échelle dans la gestion du verdissement. La publication d’un plan d’action majeur de verdissement urbain pour l’agglomération, et dont le leitmotiv est l’ACC, le démontre. Quelques modifications réglementaires et l’inclusion de nouveaux acteurs dans la politique témoignent aussi que la prise en compte a eu lieu. Finalement, le plan d’action fournit un cadre pour la mise en œuvre du verdissement dans les zones les plus vulnérables au CC en plus d’une structure de partage des coûts. Cependant, la mise en oeuvre du verdissement dans une visée d’ACC n'a pas été évaluée dans la présente étude. Nous avons aussi noté que la biodiversité est un enjeu d’importance qui va de pair avec l’ACC dans la politique de verdissement. Il y a donc une prise en compte, partielle, de l’ACC dans la politique publique de verdissement à Montréal (avec certains écueils). Nous arguons que l’enjeu de l’ACC sert peut-être d’argument supplémentaire pour verdir la ville plutôt que d’être un véritable moteur de transformation de la politique de verdissement.

Simulation of urban microclimates

Urban microclimates are greatly affected by urban form and texture and have a significant impact on building energy performance. The impact of urban form on energy consumption in buildings mainly relates to the availability of the uses of solar radiation, daylighting and natural ventilation. The urban heat island (UHI) effect increases the risk of overheating in buildings as well as the maximum energy demand for cooling. A need has arisen for a robust calculation tool (using the first-cut calculation method) to enable planners, architects and environmental assessors, to quickly and accurately compare the impact of different urban forms on local climate and UHI mitigation strategies. This paper describes a tool for the simulation of urban microclimates, which is developed by integrating image processing with a coupled thermal and airflow model.

Effects of urban ventilation patterns on the carbon monoxide concentration in a high-rise mega city

Carbon monoxide (CO) concentration data from 1999–2006, monitored at 5 different pollution stations in a high-rise mega city (Hong Kong), were collected and investigated. The spatio-temporal characteristics of urban CO concentration profiles were obtained. A new approach was put forward to examine the relationship between urban CO concentration and different wind flow patterns. Rather than relying on the meteorological data from a single weather station, usually adopted in previous studies, four weather stations on the boundary of Hong Kong territory were used in the present study so as to identify 16 different wind flow patterns, among which a typical urban heat island circulation (UHIC) can be distinguished. Higher concentrations were observed to be associated with the flow pattern of an inflow from Lau Fau Shan (LFS) station which is located in the northwest of Hong Kong. This suggests that the ability of dilution for north-to-west wind is relatively weak due to the pollutants carried from outside Hong Kong. The effectiveness of wind speed on the alleviation of urban concentration is dependent on the initial concentration of the approaching wind. The increase of wind speed of north-to-west wind from 0 m/s to 6 m/s has little effect on the reduction of urban CO concentration, especially on the non-roadside stations. By contrast, for the southerly marine wind, pollution concentration decreases sharply with an increase in the wind speed. It was also found that urban heat island circulation (UHIC) is conducive of the accumulation of pollutants, especially at night. There exists a positive correlation between CO concentration and UHI intensity. This correlation is much stronger at night compared to during the day. Keywords: urban pollution monitoring, urban ventilation pattern, urban heat island circulation, mega city