Anomalous profile of a self-reversed resonance line from Ba+ in a laser produced plasma from YBa2Cu307

A laser produced plasma from the multielement solid target YBa2Cu3O7 is generated using 1.06 μm, 9 ns pulses from a Q-switched Nd:YAG laser in air at atmospheric pressure. A time resolved analysis of the profile of the 4554.03 Å resonance line emission from Ba II at various laser power densities has been carried out. It has been found that the line has a profile which is strongly self-reversed. It is also observed that at laser power densities equal to or exceeding 1.6×1011 W cm−2, a third peak begins to develop at the centre of the self-reversed profile and this has been interpreted as due to the anisotropic resonance scattering (fluorescence). The number densities of singly ionized barium ions evaluated from the width of the resonance line as a function of time delay with respect to the beginning of the laser pulse give typical values of the order of 1019 cm−3. The higher ion concentrations existing at smaller time delays are seen to decrease rapidly. The Ba II ions in the ground state resonantly absorb the radiation and this absorption is maximum around 120 ns after the laser pulse.

Hepatozoon griseisciuri in grey squirrels (Sciurus carolinensis): changes of blood leucocyte numbers resulting from infection

Numbers of leucocytes in squirrels with gametocytes of Hepatozoon in their blood (infected) were compared with animals without gametocytes (uninfected). Typical values for leucocytes/mm(3) blood in uninfected squirrels were: leucocytes 5-7 x 10(3), granulocytes 3-4 x 10(3), lymphocytes 2-0 x 10(3) and monocytes 0-3 x 10(3) cells. Infection caused an increase in monocytes, lymphocytes and granulocytes, and there was a significant positive association between parasitaemia level and numbers of both total leucocytes and monocytes. Infected animals had more uninfected monocytes/mm(3) blood than did uninfected animals. The proportions of monocytes were more variable over time in infected animals, but no shift between infected and uninfected status was detected. Transfer of serum from infected squirrels to mice resulted in elevated counts of total blood leucocytes, monocytes and granulocytes, but not of lymphocytes, as compared with controls. Serum from squirrels with high parasitaemias had a more marked effect than serum from squirrels with low parasitaemias. Results indicate an infection - related monocytosis, possibly controlled by cytokines, that increases the number of cells available for invasion by gametocytes, thus enhancing the chances of parasite transmission.

Verification of cloud-fraction forecasts

Cloud radar and lidar can be used to evaluate the skill of numerical weather prediction models in forecasting the timing and placement of clouds, but care must be taken in choosing the appropriate metric of skill to use due to the non- Gaussian nature of cloud-fraction distributions. We compare the properties of a number of different verification measures and conclude that of existing measures the Log of Odds Ratio is the most suitable for cloud fraction. We also propose a new measure, the Symmetric Extreme Dependency Score, which has very attractive properties, being equitable (for large samples), difficult to hedge and independent of the frequency of occurrence of the quantity being verified. We then use data from five European ground-based sites and seven forecast models, processed using the ‘Cloudnet’ analysis system, to investigate the dependence of forecast skill on cloud fraction threshold (for binary skill scores), height, horizontal scale and (for the Met Office and German Weather Service models) forecast lead time. The models are found to be least skillful at predicting the timing and placement of boundary-layer clouds and most skilful at predicting mid-level clouds, although in the latter case they tend to underestimate mean cloud fraction when cloud is present. It is found that skill decreases approximately inverse-exponentially with forecast lead time, enabling a forecast ‘half-life’ to be estimated. When considering the skill of instantaneous model snapshots, we find typical values ranging between 2.5 and 4.5 days. Copyright c 2009 Royal Meteorological Society

Characterization and antimicrobial efficacy against E. coli of a helium/air plasma at atmospheric pressure created in a plastic package

A plasma source, sustained by the application of a floating high voltage (±15 kV) to parallel-plate electrodes at 50 Hz, has been achieved in a helium/air mixture at atmospheric pressure (P = 105 Pa) contained in a zip-locked plastic package placed in the electrode gap. Some of the physical and antimicrobial properties of this apparatus were established with a view to ascertain its performance as a prototype for the disinfection of fresh produce. The current–voltage (I–V) and charge–voltage (Q–V) characteristics of the system were measured as a function of gap distance d, in the range (3 × 103 ≤ Pd ≤ 1.0 × 104 Pa m). The electrical measurements showed this plasma source to exhibit the characteristic behaviour of a dielectric barrier discharge in the filamentary mode and its properties could be accurately interpreted by the two-capacitance in series model. The power consumed by the discharge and the reduced field strength were found to decrease quadratically from 12.0 W to 4.5 W and linearly from 140 Td to 50 Td, respectively, in the range studied. Emission spectra of the discharge were recorded on a relative intensity scale and the dominant spectral features could be assigned to strong vibrational bands in the 2+ and 1− systems of N2 and ${\rm N}_2^+$ , respectively, with other weak signatures from the NO and OH radicals and the N+, He and O atomic species. Absolute spectral intensities were also recorded and interpreted by comparison with the non-equilibrium synthetic spectra generated by the computer code SPECAIR. At an inter-electrode gap of 0.04 m, this comparison yielded typical values for the electron, vibrational and translational (gas) temperatures of (4980 ± 100) K, (2700 ± 200) K and (300 ± 100) K, respectively and an electron density of 1.0 × 1017 m−3. A Boltzmann plot also provided a value of (3200 ± 200 K) for the vibrational temperature. The antimicrobial efficacy was assessed by studying the resistance of both Escherichia coli K12 its isogenic mutants in soxR, soxS, oxyR, rpoS and dnaK selected to identify possible cellular responses and targets related with 5 min exposure to the active gas in proximity of, but not directly in, the path of the discharge filaments. Both the parent strain and mutants populations were significantly reduced by more than 1.5 log cycles in these conditions, showing the potential of the system. Post-treatment storage studies showed that some transcription regulators and specific genes related to oxidative stress play an important role in the E. coli repair mechanism and that plasma exposure affects specific cell regulator systems.

Is the LHC observing the pseudoscalar state of a two-Higgs-doublet model?

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Structural features of silicas prepared in n-heptane/water/ethanol/sodium dodecylsulfate microemulsions

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Asymptotic approach for the nonlinear equatorial long wave interactions

In the present work we use an asymptotic approach to obtain the long wave equations. The shallow water equation is put as a function of an external parameter that is a measure of both the spatial scales anisotropy and the fast to slow time ratio. The values given to the external parameters are consistent with those computed using typical values of the perturbations in tropical dynamics. Asymptotically, the model converge toward the long wave model. Thus, it is possible to go toward the long wave approximation through intermediate realizable states. With this approach, the resonant nonlinear wave interactions are studied. To simplify, the reduced dynamics of a single resonant triad is used for some selected equatorial trios. It was verified by both theoretical and numerical results that the nonlinear energy exchange period increases smoothly as we move toward the long wave approach. The magnitude of the energy exchanges is also modified, but in this case depends on the particular triad used and also on the initial energy partition among the triad components. Some implications of the results for the tropical dynamics are disccussed. In particular, we discuss the implications of the results for El Nĩo and the Madden-Julian in connection with other scales of time and spatial variability. © Published under licence by IOP Publishing Ltd.

Experimental study of bottom feed updraft gasifier

The updraft biomass gasifiers currently available produce a gas with high tar content. For almost all downstream applications a substantial reduction of the tar concentration is required. The gravimetric tar concentration behavior in producer gas, obtained at a modified updraft fixed bed gasifier, was studied. The feedstock feeding system was modified respect to the traditional updraft gasification design in order to decrease the tar concentration in the producer gas; the material is feeding continuously through a conduit in the base of the reactor over the grate. The caloric power of the syngas obtained was slightly lower than the typical value for this type of reactor and the highest efficiency obtained for the woodchip gasification was 77%. The highest tar concentration obtained during the experiments was 1652.7 mg N m-3 during the first our of experiments, comparable with the smaller value reported for the updraft reactors, this value is reduced significantly after the stabilization of the gasification process in the reactor. The smaller value obtained was 21 mg N m-3. © 2013 Elsevier Ltd.

Mathematical modeling and analysis of the flocculation process in chambers in series

In this study, the flocculation process in continuous systems with chambers in series was analyzed using the classical kinetic model of aggregation and break-up proposed by Argaman and Kaufman, which incorporates two main parameters: K (a) and K (b). Typical values for these parameters were used, i. e., K (a) = 3.68 x 10(-5)-1.83 x 10(-4) and K (b) = 1.83 x 10(-7)-2.30 x 10(-7) s(-1). The analysis consisted of performing simulations of system behavior under different operating conditions, including variations in the number of chambers used and the utilization of fixed or scaled velocity gradients in the units. The response variable analyzed in all simulations was the total retention time necessary to achieve a given flocculation efficiency, which was determined by means of conventional solution methods of nonlinear algebraic equations, corresponding to the material balances on the system. Values for the number of chambers ranging from 1 to 5, velocity gradients of 20-60 s(-1) and flocculation efficiencies of 50-90 % were adopted.

Measuring the Spin of Black Holes in Binary Systems Using Gravitational Waves

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Propriedades estruturais de géis de sílica preparados com adições de dodecil sulfato de sódio

This work aims to study the structural characteristics of silica gels obtained from the acid hydrolysis of tetraethoxysilane (TEOS) in water solutions with different concentrations of sodium dodecyl sulfate (SDS). The structural characteristics were studied in stages ranging from the wet gel to the dry stages of the gels (aerogels and xerogels). Aerogels were obtained by ambient pressure drying (APD) after silylation process using trimethylchlorosilane (TMCS) as silylating agent. Xerogels were obtained by conventional evaporating the liquid phase from non silylated gels. The samples were characterized by nitrogen adsorption and small angle X-ray scattering (SAXS). The structure of the wet gels and of the aerogels prepared with the surfactant exhibited characteristics of mass-fractal structures with fractal dimension D in the range 2.1-2.2 for the wet gels and 2.3-2.4 for the aerogels. The characteristic size  of the fractal domain reduces while the size a0 of the primary silica particle composing the fractal structure increases with the drying of the gels, in a process in which share of the porosity is eliminated. Aerogels exhibited typical values for the specific surface of 900 m2g-1 and of 3.5 cm3.g-1 for the total pore volume. These values are correspondingly comparable to those of the aerogels prepared by supercritical drying, since the silylation process replaces hydrophilic –OH groups by hydrophobic –Si-R3 ones, inhibiting the porosity elimination on drying. The silica particle size also increases lightly with the silylation because the attachment of the –Si-R3 groups on the silica surface. The pore size distribution curves of the aerogels are similar for all samples exhibiting a maximum in around 40 nm, independent the concentration of surfactant. This suggests that the characteristic size of 40 nm is due to the association of surfactant micelles... (Complete abstract click electronic access below)

A proposal for reservoir volume calculation in rainwater harvesting systems

This paper introduces a proposal for reservoir volume calculation in rainwater harvesting systems. The proposed method can be used for reservoir volume design in rainwater harvesting systems and is based on three important variables. These variables are water demand, system efficiency and repayment time. Several simulations were carried out in different scenarios considering typical values of both catchment area (for low-income and medium-income households) and water demand, with fixed water and tank costs. Results showed that the integrated analysis of demand, efficiency and repayment time may assist designers to determine a more adequate reservoir volume.

Análiseda percolação de água em barragem de terra pelo método da eletrorresistividade

Interventions in nature made by man are very common since the beginnings of human history, especially in the case regarding the storage of water. The construction of dams have been and still are fundamental in maintaining human life due to the vital importance that water plays. The size of these structures vary according to need, such as water catchment, fish-farming or electricity generation. Embankment dams are the most common type of these structures. Can be defined as dams natural material obtained from loan chambers located near the dam site. This type of barrier may be divided into earth dams and rockfill dams. The study area covers an earth dam located in Cordeirópolis (SP) and is essentially composed of diabases altered soil of the Serra Geral Formation of the Paraná Basin. With the aid of geophysics, more specifically of the Electrical Resistivity method, the aim is to check any water infiltration zones in the dam's body. Given the risks associated with water seepage in earth dams, that may generate breakdown structures, erosion, and consequently accidents and / or harmful factors in the nearby areas. One of the main structural problems married by water infiltration is the possible generation of pipes that could jeopardize the dam structure. This work aims to contribute towards the evaluation of the effectiveness of using an indirect technique of research and monitoring in aid to direct research techniques such as piezometers and drive stakes. The results are presented in the form of 2D and 3D geophysical models, the analysis shows a low resistivity zone with typical values of the presence of humidity originating upstream of the dam and downstream bottleneck trend, that are the basis for interpretation by percolation or not water in the dam

Is the LHC observing the pseudoscalar state of a two-Higgs-doublet model?

The ATLAS and CMS collaborations have recently shown data suggesting the presence of a Higgs boson in the vicinity of 125 GeV. We show that a two-Higgs-doublet model spectrum, with the pseudoscalar state being the lightest, could be responsible for the diphoton signal events. In this model, the other scalars are considerably heavier and are not excluded by the current LHC data. If this assumption is correct, future LHC data should show a strengthening of the gamma gamma signal, while the signals in the ZZ(()*()) -> 4l and WW(*()) -> 2l2 nu channels should diminish and eventually disappear, due to the absence of diboson tree-level couplings of the CP-odd state. The heavier CP-even neutral scalars can now decay into channels involving the CP-odd light scalar which, together with their larger masses, allow them to avoid the existing bounds on Higgs searches. We suggest additional signals to confirm this scenario at the LHC, in the decay channels of the heavier scalars into AA and AZ. Finally, this inverted two-Higgs-doublet spectrum is characteristic in models where fermion condensation leads to electroweak symmetry breaking. We show that in these theories it is possible to obtain the observed diphoton signal at or somewhat above the prediction for the standard model Higgs for the typical values of the parameters predicted.

Hygroskopische Eigenschaften atmosphärischer Partikel in kontinentalen Luftmassen

Die hygroskopischen Eigenschaften sind wichtige Parameter des atmosphärischen Aerosols. Sie beeinflussen sowohl direkt über den Strahlungsantrieb, als auch indirekt über die Wechselwirkung von Aerosol und Wolken die globale Strahlungsbilanz und somit das Klima. Auch die Sichtweiteveränderung ist von ihnen abhängig. Sie beeinflussen die Partikeldeposition in der Lunge und müssen zur Vermeidung von Artefaktbildung bei der Aerosolmessung berücksichtigt werden.
Die vorliegende Dissertation beinhaltet Messungen des wasserlöslichen Volumenanteils und des hygroskopischen Wachstumsfaktors des atmosphärischen Aerosols. Mit diesen Untersuchungen konnte der überwiegende Teil (50 nm bis 4 µm Partikeldurchmesser) des für atmosphärische Prozesse relevanten Größenbereichs gleichzeitig größenaufgelöst und detailliert erfasst werden. Messungen wurden in ruralen, semi-urbanen und frei-troposphärischen Luftmassen durchgeführt. Messverfahren sind die SoFA (Water-Soluble Fraction of Large and Giant Atmospheric Particles)-Methode und der HTDMA (Hygroscopic Tandem Differential Mobility Analyzer). Im Rahmen dieser Arbeit wurde die SoFA-Methode weiterentwickelt.
Ein umfangreiches Messprogramm zeigt, dass der mittlere lösliche Volumenanteil des Aerosols mit Werten von ca. 59 % geringe Variationen zwischen den Messstandorten aufweist, lediglich in frei-troposphärischen Luftmassen liegt er mit 66 % erwartungsgemäß höher. Betrachtet man die Daten größenaufgelöst, so zeigt sich, dass im Größenbereich zwischen 200 und 500 nm Partikeldurchmesser der lösliche Volumenanteil ein Maximum aufweist. Ein in semi-urbanem Aerosol gemessener Jahresgang weist, vor allem für Partikel kleiner 300 nm, im Sommer geringere Werte als im Winter auf. Unterhalb 300 nm Partikeldurchmesser treten üblicherweise zwei, oberhalb bis zu drei Partikeltypen unterschiedlicher Hygroskopizität auf: der fast unlösliche Partikeltyp mit löslichen Volumenanteilen bis 12 %, der wahrscheinlich aus Ruß, sekundärem organischem, mineralischem und biologischem Material besteht; der teilweise lösliche Partikeltyp (50 bis 75 %), der als Mischpartikel anzusprechen ist; schließlich der überwiegend lösliche Partikeltyp (ca. 90 %), der wahrscheinlich durch Wolkenprozessierung entsteht. Der Unterschied zwischen den Messstandorten ist auch hier gering. Üblicherweise dominieren die löslicheren Partikeltypen mit relativen Anteilen von 60 bis 95 %, wobei sich ein Minimum der Häufigkeit der löslicheren Partikel zwischen 1.5 und 2.5 µm zeigt. Abschließende größenaufgelöste Modellrechnungen zum Aerosol-Feuchtewachstum unterstreichen die Relevanz dieser Untersuchungen für Strahlungs- und Wolkenprozesse.