In-plane stiffness of timber floors strengthened with CLT

Five full-scale timber floors were tested in order to analyse the in-plane behaviour of these structural systems. The main objective was an assessment of the effectiveness of in-plane strengthening using cross-laminated timber (CLT). To this end, one unstrengthened specimen (original), one specimen strengthened with a second layer of floorboards, two specimens strengthened with three CLT panels, and one specimen strengthened with two CLT panels, were tested. A numerical analysis was then performed in order to analyse the composite behaviour of the timber floors in more detail. Due to its importance as regards composite behaviour, the first phase of the experimental programme was composed of push-out tests on specimens representing the shear connection between the timber beams and the CLT panels. This paper describes the tests performed and the numerical modelling applied to evaluate the composite behaviour of the strengthened timber floors. The use of CLT panels is revealed to be an effective way to increase the in-plane stiffness of timber floors, through which the behaviour of the composite structure can be significantly changed, depending on the connection applied, or modified as required.

Influence of the wood mechanical properties in the dovetail joint behavior

The force distribution inside a dovetail joint is complex. Wood is simultaneously loaded in different directions in the several connected surfaces. The analytical solutions available for the analysis of the behavior of those carpentry joints rely on the mechanical properties of wood. In particular, the stiffness properties of wood under compression are crucial for the forces equilibrium. Simulations showed that the stiffness values considered in each of the springs normally assumed in the analytical models, have great influence in the bearing capacity and stiffness of the dovetail joints, with important consequence on the stress distribution over the overall structure. In a wide experimental campaign, the properties under compression of the most common wood species of existing timber structures have been determined. Then, a solved example of a dovetail joint is presented assuming different wood species and the corresponding strength and stiffness properties values obtained in the tests.

Behaviour of a dovetail joint solved using force analyses

Dovetail joints are one of the most cornrnonly used joints during Gothic and Baroque periods. Despite being coristructed in the sarne way during the ages, there is no analyticai solution available to help its analysis and design so required in reconstruction works of existing timber structures. An analytical solution based on the principie of virtual works under different types of loading is presented in this paper as weli as differences in bearing capacity of the joint for chosen types of loading, when different wood species are used. The accuracy of the presented solution is confirrned by data obtained from experimental tests of scaied modeis of a dovetail joint.

Structural analysis of the timber structure of Ica Cathedral, Peru

Dissertação de mestrado em Structural Analysis of Monuments and Historical Constructions

A integração de técnicas BIM (Building Information Modeling) no projeto e na construção de estruturas de madeira

Dissertação de mestrado integrado em Engenharia Civil

Reforço de ligações tradicionais de madeira

Dissertação de mestrado integrado em Engenharia Civil

Sustainability, Fashion Design, and Consumerism: Undergraduate Entry Level Fashion Students' Knowledge, Attitudes, and Habits

This qualitative inquiry explored 7 undergraduate students' attitudes, habits, and knowledge of consumerism, fashion design, and sustainability. The postmodern study employed crystallization as its methodological framework to gain insight into how participants' knowledge is manifested in their daily habits, and used 4 methods of data gathering: semistructured interviews, visual exercises, journal entries, and the researcher's own reflections. Four major themes emerged: Knowledge-Concepts Linked and Fragmented; Dissonance Between Knowledge Versus Attitudes and Consumer Habits; Surrendering to the Unsustainable Structures; Design Process and Caring Attitude. Findings indicate that participants possessed some knowledge of sustainability but lacked a well-rounded understanding of environmental and humanitarian implications of Western consumer society. Findings also reveal a dissonance between participants' knowledge and attitudes-affecting how their knowledge influences their behaviour-and how reflection, creative thinking, and drawing initiate change in participants' underlying attitudes. Recommendations are made to merge a variety of theoretical frameworks into the educational system in order to create curricula that offer a holistic overview and unique insights into sustainability challenges, particularly in specialized areas of the fashion industry.

Design of a control system using linear matrix inequalities for the active vibration control of a plate

The study of algorithms for active vibration control in smart structures is an area of interest, mainly due to the demand for better performance of mechanical systems, such as aircraft and aerospace structures. Smart structures, formed using actuators and sensors, can improve the dynamic performance with the application of several kinds of controllers. This article describes the application of a technique based on linear matrix inequalities (LMI) to design an active control system. The positioning of the actuators, the design of a robust state feedback controller and the design of an observer are all achieved using LMI. The following are considered in the controller design: limited actuator input, bounded output (energy) and robustness to parametric uncertainties. Active vibration control of a flat plate is chosen as an application example. The model is identified using experimental data by an eigensystem realization algorithm (ERA) and the placement of the two piezoelectric actuators and single sensor is determined using a finite element model (FEM) and an optimization procedure. A robust controller for active damping is designed using an LMI framework, and a reduced model with observation and control spillover effects is implemented using a computer. The simulation results demonstrate the efficacy of the approach, and show that the control system increases the damping in some of the modes.

Reliability of timber bridges using nailed plywood box beams

The Nailed Box Beam structural efficiency is directly dependent of the flange-web joint behavior, which determines the partial composition of the section, as the displacement between elements reduces the effective rigidity of the section and changes the stress distribution and the total displacement of the section. This work discusses the use of Nailed Plywood Box Beams in small span timber bridges, focusing on the reliability of the beam element. It is presented the results of tests carried out in 21 full scale Nailed Plywood Box Beams. The analysis of maximum load tests results shows that it presents a normal distribution, permitting the characteristic values calculation as the normal distribution theory specifies. The reliability of those elements was analyzed focusing on a timber bridge design, to estimate the failure probability in function of the load level.

Variação, herdabilidade e ganhos genéticos em progênies de eucalyptus tereticornis aos 25 anos de idade em Batatais – SP

Pós-graduação em Agronomia - FEIS

Variação, herdabilidade e ganhos genéticos em progênies de Eucalyptus tereticornis aos 25 anos de idade em Batatais-SP

The wood of Eucalyptus tereticornis is intensively used for timber, structures, buildings, poles, posts and coal. The aim of this study was to estimate genetic parameters and genetic and phenotypic correlations in growth and stem form traits of 52 open-pollinated progenies of E. tereticornis sampled from three Australian populations (20 progenies from Helenvale, 19 from Ravenshoe and 13 from Mt. Garnet). The progenies were compared with three commercial control also from Australian. The experimental design used was the compact family block, with the effect of provenance allocated in the plots and progenies within provenances in the subplots. Ten repetitions of the 52 treatments, sub-plots with six plants and the spacing of 3 x 2 m was used. At 25 years of age it was measured the diameter at breast height (DBH), total height, true volume and the stem form. We found genetic variation amon and within the three provenances and the possibility of obtaining high gains from mass selection and individual among and within progenies. The provenance Helenvale showed the best development for DBH, height and volume. The traits DBH, height and volume showed high genetic correlations (> 0.9), indicating the possibility to use the indirect selection. The coefficient of heritability on a progeny mean for the traits DBH and height was median, being 0.31 and 0.30, respectively. The expected genetic gain with the selection were estimated at 12.4% for DBH and 8.5 % for plant height. These results will subsidize the transformation of the provenance and progeny test in a seedling seed orchard and a clonal seed orchard.

Comparação entre valores de ensaios experimentais e calculados da resistência ao embutimento da madeira de Pinus taeda L.

To design connections between timber parts with metal dowels (nails or bolts), two phenomena must be considered: bending of the metal dowel and the embedment strength in the wood. The Brazilian Standard ABNT NBR 7190:1997 proposes the methods used in the laboratory tests to determine the embedment strength with the metal dowell and, in the absence of testing, specifies relations to calculate the embedment strength from the compression strength. The aim of this research was to compare the embedment strength values obtained by experimental tests and calculated by the relationships established by the Brazilian Standard ABNT NBR 7190:1997. By the results of the hypothesis tests, it was possible to conclude that the estimate of the embedment strength parallel to the grain proposed by the Brazilian standard ABNT NBR 7190:1997, establishing equivalence with the strength compression results in the same direction, must be effective to the wood species Pinus taeda L., however, the same was not found in the perpendicular direction with respect to the grain, possibly explained by the alpha(e) values in the equation to calculed fe(90)

Influence of the number of load cycles to obtain the stiffness properties of angico preto (Anadenanthera macrocarpa) wood specie

The tests used to obtain the stiffness properties of wood are made with two loading cycles, as defined by the Brazilian standard ABNT NBR 7190 (Design of Timber Structures). However, the possibility of reducing the number of cycles allows decrease the operating time of the machine, resulting in reduced spending on electricity used during the tests. This research aimed to investigate, with the aid of the analysis of variance (ANOVA), the influence of the use of three load cycles to obtain the modulus of elasticity in compression parallel to grain (Ec0), in tensile parallel to the grain (Et0), in bending (Em) and in compression perpendicular to the grain (Ec90) of Angico Preto (Anadenanthera macrocarpa) wood specie. For the number of cycles and stiffness were manufactured 12 samples, totaling 144 specimens. The results of the ANOVA revealed statistical equivalence between the stiffness properties for both load cycle numbers evaluated, indicating that it is possible to carry out the tests with a single charge cycle, allowing savings in time and energy in the operation of the equipment.

Bonding shear strength in timber and GFRP glued with epoxy adhesives

The bonding quality of epoxy glued timber and glass fibre reinforced polymers (GFRP) was evaluated by means of compression loading shear test. Three timber species (Radiata pine, Laricio pine and Oak) and two kinds of GFRP (plates and rods made with polyester resin reinforced with mat and roving glass fibre) were glued and tested using three epoxy formulations. The increase in shear strength with age after the setting of epoxy formulations and the effect of surface roughness on timber and GRP gluing (the planing of the surface of timber and the previous sanding of GRP) were studied. It can be concluded that the mechanical properties of these products make them suitable for use in the reinforcement of deteriorated timber structures, and that a rough timber surface is preferable to a planed one, while the previous sanding of GRP surfaces is not advantageous.

Visual grading of large cross section structural timber of Pinus sylvestris L. according to UNE 56544:2007 standard

Large cross section structural timber have been used in many structures over long periods of time and still make up an important part of the market due to its mechanical properties. Furthermore, it is frequent its employment in new construction site. It involves the need for a visual grading standard for timber used in construction according to the quality assessment. The material has to satisfy the requirements according to the currently regulations. UNE 56544 is the Spanish visual grading standard for coniferous structural timber. The 2007 version defined a new visual grade in the standard for large section termed Structural Large Timber (MEG). This research checks the new visual grading and consists of 116 structural size specimens of sawn coniferous timber of Scotch pine (Pinus sylvestris L.) from Segovia, Spain. The pieces had a cross section of 150 by 200 mm. They were visually graded according to UNE 56544:2007. Also, mechanical properties have been obtained according to standard EN 408. The results show very low output with an excessive percentage of rejected pieces (33%). The main reasons for the rejection of pieces are fissures and twist