Friction and wear in thrust ball bearings lubricated with biodegradable greases

Thrust ball bearings lubricated with several different types of grease, including three biodegradable low-toxicity greases, were tested in a modified four-ball machine in order to evaluate the bearing friction torque. At the end of each test, grease samples were obtained and analysed through ferrography, allowing the quantification and evaluation of the bearing wear. In order to compare the grease performance in terms of friction and wear, a correlation between the grease characteristics (base oil, bleed oil, thickener structure, and rheological parameters) and the experimental results was established.

Low torque loss gears: austempered ductile iron versus carburized steel

Low-loss power transmission gears operate at lower temperature than conventional ones because their teeth geometry is optimized to reduce friction. The main objective of this work is to compare the operating stabilization temperature and efficiency of low-loss austempered ductile iron (ADI) and carburized steel gears. Three different low-loss tooth geometries were adopted (types 311, 411 and 611, all produced using standard 20° pressure angle tools) and corresponding steel and ADI gears were tested in a FZG machine. The results obtained showed that low-loss geometries had a significant influence on power loss, gears 611 generating lower power loss than gears 311. At low speeds (500 and 1000 rpm) and high torque ADI gears generated lower power loss than steel gears. However, at high speed and high torque (high input power and high stabilization temperature) steel gears had better efficiency.

Friction torque in grease lubricated thrust ball bearings

Thrust ball bearings lubricated with several different greases were tested on a modified Four-Ball Machine, where the Four-Ball arrangement was replaced by a bearing assembly. The friction torque and operating temperatures in a thrust ball bearing were measured during the tests. At the end of each test a grease sample was analyzed through ferrographic techniques in order to quantify and evaluate bearing wear. A rolling bearing friction torque model was used and the coefficient of friction in full film lubrication was determined for each grease, depending on the operating conditions. The experimental results obtained showed that grease formulation had a very significant influence on friction torque and operating temperature. The friction torque depends on the viscosity of the grease base oil, on its nature (mineral, ester, PAO, etc.), on the coefficient of friction in full film conditions, but also on the interaction between grease thickener and base oil, which affected contact replenishment and contact starvation, and thus influenced the friction torque.

Influence of grease formulation on thrust bearings power loss

The minimization of the power loss and the use of the biodegradable greases have attracting considerable attention. To compare the energetic performance of biodegradable lubricant greases, power loss tests were performed on a modified four-ball machine. A correlation between the grease formulation and rheology was established with its energetic performance

Einfluss des Zylinderdruckverlaufes auf den Reibmitteldruck eines Benzinmotors mit Direkteinspritzung

Friction; tribology; gasoline direct injection; oil film thinkness; in-cylinder pressure; friction mean effective pressure; heat release; tangential piston forces; film temperatures

Obtencion de recubrimientos autolubricados por proyeccion termica de plasma atmosferico (APS) como alternativa a los lubricantes liquidos

La obtención de recubrimientos con bajos coeficientes de fricción, es una innovadora respuesta a la creciente demanda industrial de alternativas para los tradicionales sistemas lubricados con aceites. Para este fin, la introducción de un sólido lubricante, en una matriz con buenas propiedades mecánicas, ha de conferir al conjunto un bajo coeficiente de fricción y mejorar la resistencia al desgaste del recubrimiento, favoreciendo además, la utilización a elevadas temperaturas, en las que los lubricantes líquidos convencionales presentan limitaciones. En el Centro de Proyección Térmica (CPT) de la Universidad de Barcelona se han obtenido mediante proyección de Plasma Atmosférico (APS) recubrimientos autolubricados de Ni-Grafito y Cr2O3-CaF2, estudiando con especial interés las propiedades y el efecto que produce el grafito y el CaF2 en las matrices metálica y cerámica respectivamente. Se ha determinado en los dos casos que el desgaste originado en los recubrimientos es bajo, si bien los coeficientes de fricción varían ostensiblemente en función del sistema indicado. Los resultados obtenidos indican que el recubrimiento de Ni-Grafito posee un comportamiento idóneo capaz de competir con los tradicionales lubricantes líquidos.

Tribologia de Recubrimientos de Cermet/NiCrBSi Aplicables a la Obtencion de Recubrimientos y Conformados Resistentes al Desgaste

El trabajo consta de un completo estudio tribológico del sistema WX que consiste en la mezcla mecánica de WC-12Co y NiCrBSi en diferentes proporciones: 20% NiCrBSi (W2), 40% NiCrBSi (W4) y 60% NiCrBSi (W6). Los recubrimientos se han obtenido por proyección térmica de alta velocidad (HVOF). Para todos los sistemas, el coeficiente de fricción es menor que 0.5 y la energía intercambiada entre el par friccionante y el recubrimiento es inferior a 10 KJ. Para cuantificar el desgaste por fricción se han utilizado la profundidad de la huella y el volumen perdido durante el ensayo, obtenidos mediante Interferometría de Barrido de Luz Blanca (SLWI) y SEM. La profundidad de la huella sigue una evolución directamente proporcional al contenido en NiCrBSi. Un mayor contenido en WC-12Co aumenta la resistencia al desgaste por fricción y disminuye la velocidad de desgaste por abrasión (ensayo Rubber Wheel). En los recubrimientos obtenidos, no se observa difusión entre las fases, la adherencia con el sustrato es excelente, la porosidad menor al 2% y se produce un incremento de la dureza del recubrimiento debido al endurecimiento por trabajo de la matriz causada por impacto.

Estudio Mediante Tecnicas Interferometricas de las Propiedades Tribologicas de la ZrO2 Obtenida por Proyeccion Termica

Las barreras térmicas poseen unas propiedades mecánicas y tribológicas limitadas. Los tratamientos térmicos de sintetizado pueden utilizarse como una posible solución para su mejora. En el presente trabajo se evalúa la evolución de diversas propiedades tribológicas y mecánicas, a diferentes tiempos de sinterización, a temperatura de 1.000 °C. Se observa que el sintetizado produce un aumento de la resistencia al desgaste, de la dureza y del módulo de Young. A partir de los ensayos ball-on-disk, realizados utilizando un par friccionante de ZrO2 y de acero, se han estudiado los mecanismos de desgaste dominantes para cada uno de los pares friccionantes. Se ha observado que la delaminación entre partículas y la fractura frágil durante el proceso de desgaste son los mecanismos principales que controlan el proceso. Los caminos de desgaste estudiados mediante microscopía electrónica de barrido (SEM) e interferometría de barrido de luz blanca (SWLI) han permitido cuantificar el desgaste en cada uno de los casos. A fin de poder estudiar los recubrimientos de ZrO2 mediante SEM y SWLI ha sido necesario realizar una metalización con oro para así aumentar la conductividad eléctrica y reflectividad de las muestras.

Materials selection for superheater tubes in municipal solid waste incineration plants

Corrosion reduces the lifetime of municipal solid waste incineration (MSWI) superheater tubes more than any other cause. It can be minimized by the careful selection of those materials that are most resistant to corrosion under operating conditions. Since thousands of different materials are already known and many more are developed every year, here the selection methodology developed by Prof. Ashby of the University of Cambridge was used to evaluate the performance of different materials to be used as MSWI superheater tubes. The proposed materials can operate at steam pressures and temperatures over 40 bars and 400ºC, respectively. Two case studies are presented: one makes a balanced selection between mechanical properties and cost per thermal unit; and the other focuses on increasing tube lifetime. The balanced selection showed that AISI 410 martensitic stainless steel (wrought, hard tempered) is the best candidate with a good combination of corrosion resistance, a relatively low price (0.83-0.92 e/kg) and a good thermal conductivity (23-27 W/m K). Meanwhile, Nitronic 50/XM-19 stainless steel is the most promising candidate for longterm selection, as it presents high corrosion resistance with a relatively low price (4.86-5.14 e/kg) compared to Ni-alloys.

A Mass-Conserving Algorithm for Dynamical Lubrication Problems With Cavitation

A numerical algorithm for fully dynamical lubrication problems based on the Elrod-Adams formulation of the Reynolds equation with mass-conserving boundary conditions is described. A simple but effective relaxation scheme is used to update the solution maintaining the complementarity conditions on the variables that represent the pressure and fluid fraction. The equations of motion are discretized in time using Newmark`s scheme, and the dynamical variables are updated within the same relaxation process just mentioned. The good behavior of the proposed algorithm is illustrated in two examples: an oscillatory squeeze flow (for which the exact solution is available) and a dynamically loaded journal bearing. This article is accompanied by the ready-to-compile source code with the implementation of the proposed algorithm. [DOI: 10.1115/1.3142903]

Influence of surface texture on the galling characteristics of lean duplex and austenitic stainless steels

Two simulative test methods were used to study galling in sheet forming of two types of stainlesssteel sheet: austenitic (EN 1.4301) and lean duplex LDX 2101 (EN 1.4162) in different surface conditions. Thepin-on-disc test was used to analyse the galling resistance of different combinations of sheet materials and lubricants. The strip reduction test, a severe sheet forming tribology test was used to simulate the conditionsduring ironing. This investigation shows that the risk of galling is highly dependent on the surface texture of theduplex steel. Trials were also performed in an industrial tool used for high volume production of pumpcomponents, to compare forming of LDX 2101 and austenitic stainless steel with equal thickness. The forming forces, the geometry and the strains in the sheet material were compared for the same component.It was found that LDX steels can be formed to high strain levels in tools normally applied for forming ofaustenitic steels, but tool adaptations are needed to comply with the higher strength and springback of thematerial.

Mechanical and tribological properties of PVD-coated cemented carbide as evaluated by a new multi-pass scratch testing method

A new test method based on multipass scratch testing has been developed for evaluating the mechanical and tribological properties of thin, hard coatings. The proposed test method uses a pin-on-disc tribometer and during testing a Rockwell C diamond stylus is used as the “pin” and loaded against the rotating coated sample. The influence of normal load on the number of cycles to coating damage is investigated and the resulting coating damage mechanisms are evaluated by posttest scanning electron microscopy. The present study presents the test method by evaluating the performance of Ti0.86Si0.14N, Ti0.34Al0.66N, and (Al0.7Cr0.3)2O3 coatings deposited by cathodic arc evaporation on cemented carbide inserts. The results show that the test method is quick, simple, and reproducible and can preferably be used to obtain relevant data concerning the fatigue, wear, chipping, and spalling characteristics of different coating-substrate composites. The test method can be used as a virtually nondestructive test and, for example, be used to evaluate the fatigue and wear resistance as well as the cohesive and adhesive interfacial strength of coated cemented carbide inserts prior to cutting tests.

Microstructural, Mechanical and Tribological Characterisation of CVD and PVD Coatings for Metal Cutting Applications

The present thesis focuses on characterisation of microstructure and the resulting mechanical and tribological properties of CVD and PVD coatings used in metal cutting applications. These thin and hard coatings are designed to improve the tribological performance of cutting tools which in metal cutting operations may result in improved cutting performance, lower energy consumption, lower production costs and lower impact on the environment.  In order to increase the understanding of the tribological behaviour of the coating systems a number of friction and wear tests have been performed and evaluated by post-test microscopy and surface analysis. Much of the work has focused on coating cohesive and adhesive strength, surface fatigue resistance, abrasive wear resistance and friction and wear behaviour under sliding contact and metal cutting conditions. The results show that the CVD deposition of accurate crystallographic phases, e.g. α-Al2O3 rather than κ-Al2O3, textures and multilayer structures can increase the wear resistance of Al2O3. However, the characteristics of the interfaces, e.g. topography as well as interfacial porosity, have a strong impact on coating adhesion and consequently on the resulting properties.  Through the deposition of well designed bonding and template layer structures the above problems may be eliminated. Also, the presence of macro-particles in PVD coatings may have a significant impact on the interfacial adhesive strength, increasing the tendency to coating spalling and lowering the surface fatigue resistance, as well as increasing the friction in sliding contacts. Finally, the CVD-Al2O3 coating topography influences the contact conditions in sliding as well as in metal cutting. In summary, the work illuminates the importance of understanding the relationships between deposition process parameters, composition and microstructure, resulting properties and tribological performance of CVD and PVD coatings and how this knowledge can be used to develop the coating materials of tomorrow.

Desgaste de polímeros estruturais de engenharia em contato de deslizamento com cilindro metálico

Present work proposed to map and features the wear mechanisms of structural polymers of engineering derived of the sliding contact with a metallic cylindrical spindle submitted to eccentricity due to fluctuations in it is mass and geometric centers. For this it was projected and makes an experimental apparatus from balancing machine where the cylindrical counterbody was supported in two bearings and the polymeric coupon was situated in a holder with freedom of displacement along counterbody. Thus, the experimental tests were standardized using two position of the two bearings (Fixed or Free) and seven different positions along the counterbody, that permit print different conditions to the stiffness from system. Others parameters as applied normal load, sliding velocity and distance were fixed. In this investigation it was used as coupon two structural polymers of wide quotidian use, PTFE (polytetrafluroethylene) and PEEK (poly-ether-ether-ketone) and the AISI 4140 alloy steel as counterbody. Polymeric materials were characterized by thermal analysis (thermogravimetric, differential scanning calorimetry and dynamic-mechanical), hardness and rays-X diffractometry. While the metallic material was submitted at hardness, mechanical resistance tests and metallographic analysis. During the tribological tests were recorded the heating response with thermometers, yonder overall velocity vibration (VGV) and the acceleration using accelerometers. After tests the wear surface of the coupons were analyzed using a Scanning Electronic Microscopy (SEM) to morphological analysis and spectroscopy EDS to microanalysis. Moreover the roughness of the counterbody was characterized before and after the tribological tests. It was observed that the tribological response of the polymers were different in function of their distinct molecular structure. It were identified the predominant wear mechanisms in each polymer. The VGV of the PTFE was smaller than PEEK, in the condition of minimum stiffness, in function of the higher loss coefficient of that polymer. Wear rate of the PTFE was more of a magnitude order higher than PEEK. With the results was possible developed a correlation between the wear rate and parameter (E/ρ)1/2 (Young modulus, E, density, ρ), proportional at longitudinal elastic wave velocity in the material.