Simulation of Deformation Texture Evolution During Multi Axial Forging of Interstitial Free Steel

Bulk texture measurement of multi-axial forged body center cubic interstitial free steel performed in this study using x-ray and neutron diffraction indicated the presence of a strong {101}aOE (c) 111 > single texture component. Viscoplastic self-consistent simulations could successfully predict the formation of this texture component by incorporating the complicated strain path followed during this process and assuming the activity of {101}aOE (c) 111 > slip system. In addition, a first-order estimate of mechanical properties in terms of highly anisotropic yield locus and Lankford parameter was also obtained from the simulations.

Analysis of Microstructure and Texture Evolution in Mg-3Al-1Zn Alloy Processed Through Groove Rolling

The mechanism of grain refinement in a AZ31 Mg alloy subjected to hot groove rolling is investigated up to large strain (epsilon(t) similar to 2.5). The alloy shows enhanced yield strength without compromising ductility. The change in strain path during rolling has resulted in significant weakening of basal texture. The microstructure analyses show that dynamic recrystallization (DRX) contributed significantly to grain refinement and hence to the observed mechanical properties. The combined effects of DRX and texture evolution on mechanical properties have been addressed.

A material model for multiaxial stretching and stress relaxation of polypropylene under process conditions

Polypropylene sheets have been stretched at 160 °C to a state of large biaxial strain of extension ratio 3, and the stresses then allowed to relax at constant strain. The state of strain is reached via a path consisting of two sequential planar extensions, the second perpendicular to the first, under plane stress conditions with zero stress acting normal to the sheet. This strain path is highly relevant to solid phase deformation processes such as stretch blow moulding and thermoforming, and also reveals fundamental aspects of the flow rule required in the constitutive behaviour of the material. The rate of decay of stress is rapid, and such as to be highly significant in the modelling of processes that include stages of constant strain. A constitutive equation is developed that includes Eyring processes to model both the stress relaxation and strain rate dependence of the stress. The axial and transverse stresses observed during loading show that the use of a conventional Levy-Mises flow rule is ineffective, and instead a flow rule is used that takes account of the anisotropic state of the material via a power law function of the principal extension ratios. Finally the constitutive model is demonstrated to give quantitatively useful representation of the stresses both in loading and in stress relaxation.

Material properties under drawing and extrusion with cyclic torsion

A copper bar was drawn while a lead bar was extruded through a cyclically twisting die in a specifically designed experimental rig. The drawing/extrusion load fluctuated at the same frequency as that of die twisting. The load tended to be at a level of monotonic deformation when the die was changing direction. The degree of the reduction in load for both the drawing and extrusion processes depended on the deformation conditions and requires optimisation for industrial application.

A Taylor Model Based Description of the proof stress of magnesium AZ31 during hot working

A series of hot-compression tests and Taylor-model simulations were carried out with the intention of developing a simple expression for the proof stress of magnesium alloy AZ31 during hot working. A crude approximation of wrought textures as a mixture of a single ideal texture component and a random background was employed. The shears carried by each deformation system were calculated using a full-constraint Taylor model for a selection of ideal orientations as well as for random textures. These shears, in combination with the measured proof stresses, were employed to estimate the critical resolved shear stresses for basal slip, prismatic slip, ⟨c+a⟩ second-order pyramidal slip, and { } twinning. The model thus established provides a semianalytical estimation of the proof stress (a one-off Taylor simulation is required) and also indicates whether or not twinning is expected. The approach is valid for temperatures between ∼150 °C and ∼450 °C, depending on the texture, strain rate, and strain path.

Constitutive modelling of drawing and extrusion with cyclic torsion

In the current work, constitutive models are developed to describe the cyclic hardening and softening led by the strain path chaneg.  The contribution of deformation conditions such as drawing and extrusion speed, cyclic rotating angle on the drawing and extrusion force will be investigated.  The development of such constitutive models will provide insight into the optimization of operation conditions to explore the potential of industrial applications.

Stress-based predictions of formability and failure in incremental sheet forming

 This research investigates the deformation mechanism in incremental sheet forming (ISF) with relation to necking and failure. A strain-based forming limit criterion is widely used in sheet-metal forming industry to predict necking. However, this criterion is strictly valid only when the strain path is linear throughout the deformation process. Where the strain path in ISF is often found to be severely nonlinear throughout the deformation history. Therefore, the practice of using a strain-based forming limit criterion often leads to erroneous assessments of formability and failure prediction. On the other hands, stress-based forming limit is insensitive against any changes in the strain path and hence it is used to model the necking and fracture limits. Simulation model is evaluated for a single point incremental forming using AA 6022-T4E32 and checked the accuracy against experiments.

Texture analyses of ODP Site 131-808 sediments

The microfabric of 11 mudrock specimens from ODP Site 808 (Nankai accretionary prism) was quantitatively analyzed using X-ray texture goniometry and optical petrography. The objectives of the study were to learn about rock strain and to detect a component of bulk lateral shortening in the deformation of the mudstones. Strain evaluation is based on the predictions of March theory, and on distortions of initially homogeneous marker particle distributions (the Fry technique). The main results are as follows. The specimens underwent a strain path of progressive flattening, which is closely related to loss of pore space by vertical loading. A component of bulk lateral shortening is detectable in the top 550 mbsf at Site 808, but compared with the amount of uniaxial vertical shortening, its relative magnitude is probably small. Moreover, it cannot be said with confidence whether this is caused by toe contraction of the accretionary wedge or by gravitationally induced downslope movement of the sediment pile. The mudstones examined were deposited in a marine environment with an oxic bottom water column. Micropore collapse is an important fabric building mechanism, but below 400 mbsf its effects are at least partly overridden by recrystallization of smectite. We conclude that mud microfabrics are not very precise deformation gauges, but can be used for rough estimations of strain.

Stress based prediction of formability and failure in incremental sheet forming

A strain-based forming limit criterion is widely used in sheet-metal forming industry to predict necking. However, this criterion is usually valid when the strain path is linear throughout the deformation process [1]. Strain path in incremental sheet forming is often found to be severely nonlinear throughout the deformation history. Therefore, the practice of using a strain-based forming limit criterion often leads to erroneous assessments of formability and failure prediction. On the other hands, stress-based forming limit is insensitive against any changes in the strain path and hence it is first used to model the necking limit in incremental sheet forming. The stress-based forming limit is also combined with the fracture limit based on maximum shear stress criterion to show necking and fracture together. A derivation for a general mapping method from strain-based FLC to stress-based FLC using a non-quadratic yield function has been made. Simulation model is evaluated for a single point incremental forming using AA 6022-T43, and checked the accuracy against experiments. By using the path-independent necking and fracture limits, it is able to explain the deformation mechanism successfully in incremental sheet forming. The proposed model has given a good scientific basis for the development of ISF under nonlinear strain path and its usability over conventional sheet forming process as well.

Texture evolution and grain refinement of ultrafine-grained copper during micro-extrusion

Samples of oxygen-free high conductivity (OFHC) coarse-grained (CG) and ultrafine-grained (UFG) copper were micro-extruded to an equivalent strain of 2.8 in one pass at room temperature. Samples of the OFHC copper were annealed at 650C for 2 h to produce CG copper. Some samples were subsequently processed by equal channel angular pressing of eight passes, route Bc, at room temperature to produce the UFG material. Crystallographic texture and misorientation distributions were obtained locally from EBSD mappings at different radial positions after micro-extrusion. To model the strain path during micro-extrusion, the analytic flow line model of Altan etal. [J Mater. Process. Tech. 33 (1992) p.263] was used and also validated by finite element calculations. Modelling was carried out using the viscoplastic self-consistent (VPSC) model and a recently developed grain refinement model. The results showed large texture variations along the cross-section of the extruded sample for both UFG and CG copper. These cyclic drawing textures in UFG copper were simulated in good agreement with experiments using the presented modelling framework.

Finite element modeling of tube deformation during cold pilgering

A three-dimensional finite element model of cold pilgering of stainless steel tubes is developed in this paper. The objective is to use the model to increase the understanding of forces and deformations in the process. The focus is on the influence of vertical displacements of the roll stand and axial displacements of the mandrel and tube. Therefore, the rigid tools and the tube are supported with elastic springs. Additionally, the influences of friction coefficients in the tube/mandrel and tube/roll interfaces are examined. A sensitivity study is performed to investigate the influences of these parameters on the strain path and the roll separation force. The results show the importance of accounting for the displacements of the tube and rigid tools on the roll separation force and the accumulative plastic strain.

Performance study of a pressure transducer with meandering-path thin film strain gauges

The performance of a pressure transducer with meandering-path thin film strain gauges has been studied. Details of the procedure followed to prepare the thin film strain gauge system on the pressure transducer diaphragm are given. The effect of post-deposition heat treatment on the resistance of the sensing films of the strain gauges and the insulating base layers are discussed. The output of the pressure transducer was studied with various input pressures and excitation voltages. It was found that up to a maximum of 10 V bridge excitation the output was stable and repetitive. The maximum non-linearity and hysteresis observed are ±0.15%, ±0.16% and ±0.14% FSO (full-scale output) for 5, 7.5 and 10 V excitation respectively. Information on the output behaviour of the pressure transducer with temperature is also included.

Crack Tip Field and J-Integral with Strain Gradient Effect

The mode I plane strain crack tip field with strain gradient effects is presented in this paper based on a simplified strain gradient theory within the framework proposed by Acharya and Bassani. The theory retains the essential structure of the incremental version of the conventional J_2 deformation theory No higher-order stress is introduced and no extra boundary value conditions beyond the conventional ones are required. The strain gradient effects are considered in the constitutive relation only through the instantaneous tangent modulus. The strain gradient measures are included into the tangent modulus as internal parameters. Therefore the boundary value problem is the same as that in the conventional theory Two typical crack Problems are studied: (a) the crack tip field under the small scale yielding condition induced by a linear elastic mode-I K-field and (b) the complete field for a compact tension specimen. The calculated results clearly show that the stress level near the crack tip with strain gradient effects is considerable higher than that in the classical theory The singularity of the strain field near the crack tip is nearly equal to the square-root singularity and the singularity of the stress field is slightly greater than it. Consequently, the J-integral is no longer path independent and increases monotonically as the radius of the calculated circular contour decreases.

The influence of particle shape on the stress-strain and creep response of a fine silica sand

The influence of particle shape on the stress-strain response of fine silica sand is investigated experimentally. Two sands from the same source and with the same particle size distribution were examined using Fourier descriptor analysis for particle shape. Their grains were, on average, found to have similar angularity but different elongation. During triaxial stress path testing, the stress-strain behavior of the sands for both loading and creep stages were found to be influenced by particle elongation. In particular, the behavior of the sand with less elongated grains was more like that of rounded glass beads during creep. The results highlight the role of particle shape in stress transmission in granular packings and suggest that shape should be taken more rigorously into consideration in characterizing geomaterials. © 2005 Taylor & Francis Group.