Kinetic behavior of nitrification in the post-treatment of poultry wastewater in a sequential batch reactor

A sequential batch reactor with suspended biomass and useful volume of 5 L was used in the removal of nutrients and organic matter in workbench scale under optimal conditions obtained by central composite rotational design (CCRD), with cycle time (CT) of 16 h (10.15 h, aerobic phase, and 4.35 h, anoxic phase) and carbon: nitrogen ratio (COD/NO2--N+NO3--N) equal to 6. Complete cycles (20), nitrification followed by denitrification, were evaluated to investigate the kinetic behavior of degradation of organic (COD) and nitrogenated (NH4+-N, NO2--N and NO3--N) matter present in the effluent from a bird slaughterhouse and industrial processing facility, as well as to evaluate the stability of the reactor using Shewhart control charts of individual measures. The results indicate means total inorganic nitrogen (NH4+-N+NO2- -N+NO3--N) removal of 84.32±1.59% and organic matter (COD) of 53.65±8.48% in the complete process (nitrification-denitrification) with the process under statistical control. The nitrifying activity during the aerobic phase estimated from the determination of the kinetic parameters had mean K1 and K2 values of 0.00381±0.00043 min-1 and 0.00381±0.00043 min-1, respectively. The evaluation of the kinetic behavior of the conversion of nitrogen indicated a possible reduction of CT in the anoxic phase, since removals of NO2--N and NO3--N higher than 90% were obtained with only 1 h of denitrification.

Adaptive control of Hydraulic Drive

Adaptive control systems are one of the most significant research directions of modern control theory. It is well known that every mechanical appliance’s behavior noticeably depends on environmental changes, functioning-mode parameter changes and changes in technical characteristics of internal functional devices. An adaptive controller involved in control process allows reducing an influence of such changes. In spite of this such type of control methods is applied seldom due to specifics of a controller designing. The work presented in this paper shows the design process of the adaptive controller built by Lyapunov’s function method for the Hydraulic Drive. The calculation needed and the modeling were conducting with MATLAB® software including Simulink® and Symbolic Math Toolbox™ etc. In the work there was applied the Jacobi matrix linearization of the object’s mathematical model and derivation of the suitable reference models based on Newton’s characteristic polynomial. The intelligent adaptive to nonlinearities algorithm for solving Lyapunov’s equation was developed. Developed algorithm works properly but considered plant is not met requirement of functioning with. The results showed confirmation that adaptive systems application significantly increases possibilities in use devices and might be used for correction a system’s behavior dynamics.

Financial planning and Control in public sector undertakings in kerala

Today India is seeking a speedy transformation of her semi-stagnant economy to a dynamic one by means of economic planning in a democratic set up. In the context of this growth oriented endeavour public sector has a vital role to play. After three decades of planned development, it has become important that India must make fresh appraisals on the role of public sector in the economic renaissance of the country. Almost no comprehensive study has been made on this vital segment of the economy vis-a-vis the growth economics. This study is an attempt to fill this need in a very modest way. It presents the subject in a new perspective. An earnest attempt is made to reveal the critical problems inhibiting the growth of the public sector from a new angle which focusses the spot-light on the economics of development.

Process Variability in Micro-Embossing

A promising technique for the large-scale manufacture of micro-fluidic devices and photonic devices is hot embossing of polymers such as PMMA. Micro-embossing is a deformation process where the workpiece material is heated to permit easier material flow and then forced over a planar patterned tool. While there has been considerable, attention paid to process feasibility very little effort has been put into production issues such as process capability and eventual process control. In this paper, we present initial studies aimed at identifying the origins and magnitude of variability for embossing features at the micron scale in PMMA. Test parts with features ranging from 3.5- 630 µm wide and 0.9 µm deep were formed. Measurements at this scale proved very difficult, and only atomic force microscopy was able to provide resolution sufficient to identify process variations. It was found that standard deviations of widths at the 3-4 µm scale were on the order of 0.5 µm leading to a coefficient of variation as high as 13%. Clearly, the transition from test to manufacturing for this process will require understanding the causes of this variation and devising control methods to minimize its magnitude over all types of parts.

Controle estatístico aplicado ao processo de colheita mecanizada diurna e noturna de cana-de-açúcar

The system of mechanized harvesting can seek process improvements using quality tools that can assist in reducing losses, damaged ratoons and increase the longevity of sugarcane crop. Therefore, the objective this study was to detect the effective control of the variability of losses and damage to ratoon and identify whether they are within acceptable standards. Thus, 40 points were sampled in two periods of harvest, diurnal and nocturnal, in rectangular grids (55 x 45 m) for determining visible losses (whole and shattered billets, fixed and loose piece, stump and shrapnel), using frames of 10 m(2). Also, we measured the height of cut and degree of damage to ratoon (without damage, partial injury and fragmentation). The statistic used was descriptive variables for the loss of sugarcane during the diurnal (D) and nocturnal (N) periods, analysis of variance using the F test at 5% probability and the Tukey test for comparison of the mean, also using the statistical control through charts process. There was no difference to ratoon damage. In the process of harvest, losses of whole and shattered billets by grinding were considered under control, so as losses from the stump. on the other hand, the losses of fixed piece, shrapnel and whole-cane were not controlled. The cutting height and total losses were higher during the nocturnal harvest. The charts were shown to be effective for the evaluation of control process of diurnal and nocturnal harvests.

A utilização do controle estatístico do processo para o monitoramento do sangue: estudo de caso no Memonorte-RN

The present work is grounded basically on the use of the Basic Tools for the Statistic Process Control SPC, with the intent to detect non-conformities on a given productive process. It consists on a case study accomplished at a Hemocenter in Natal (Rio Grande do Norte). In this study it is shown that, the Statistic Process Control Technique, which was used as a tool, is useful to identify on-conformities on the volume of hemocomponents. The gathering of the used data was performed by means of document analysis, direct observations and database queries. The results achieved from the study show that the analyzed products, even though when they have presented, in some cases, points out of control, they satisfied the ANVISA standards. Finally, suggestions for further improvement of the final product and guidance for future employment of CEP, also extended to other lines of production, are presented

Aplicação da metodologia seis sigma em uma empresa de médio porte do setor têxtil

The Six Sigma methodology has received considerable attention in the last two decades. This is due to its great potencial to reduce processes variability, through the use of accurate data, facts and statistical techniques. The methodology seeks to improve the quality of products and services, maximizing the company s financial performance. Specifically, its implementation and results in medium-sized textile enterprises is unknow, although there are signs that the methodology can be applied with success. Considering this scenario, the goal of this research is to describe the application of the Six Sigma methodology in a médium-sized textile company specialized in the production of male shirts in the satate of Rio Grande do Norte, Brazil. First, we present a literature review, seeking to highlight the themes of quality, Six Sigma and its methodology for improvement. Then, we show the implementation of the project selected, depicting the steps and procedures that must be performed. The results confirm the efficiency of Six Sigma in providing significant gains to companies. It is observed substantial improvements in the speed of product development and the flexibility of the parts produced, reducing the process lead time from 12.5 to 6.2 days, which means a performance improvement of over 50%. This leads also to cultural and behaviour change, creating motivation for implementation of new projects and a continuous search for knowledge

Caracterização das perdas e distribuição de cobertura vegetal em colheita mecanizada de soja

O conceito de controle de qualidade nas operações inserido na agricultura é viabilizado por incidir diretamente nos principais objetivos do processo produtivo: retorno econômico e aumento da produtividade. A colheita mecanizada normalmente é realizada sem que haja controle efetivo para que a variabilidade das perdas fique dentro de padrões aceitáveis. Esta pesquisa teve o objetivo de determinar e caracterizar as perdas e a distribuição da cobertura vegetal após a colheita mecanizada da soja, por meio de ferramenta de controle estatístico de processo (cartas de controle). A média da perda de grãos total foi próxima do limite superior aceitável para a cultura da soja, apresentando alta variabilidade entre os pontos, tornando o processo fora de controle. A distribuição de cobertura vegetal manteve-se em processo controlado, com maior variabilidade onde o relevo foi mais inclinado. A utilização das cartas de controle foi eficiente na identificação dos pontos fora de controle e na avaliação da qualidade do processo de colheita.

Quality of mechanized coffee harvesting in circular planting system

A colheita mecanizada de café se destaca como um dos principais avanços tecnológicos em benefício dos produtores, porém, problemas com planejamento no plantio e desenvolvimento da cultura, bem como falhas na regulagem da colhedora, podem acarretar em redução na eficiência da operação, tornando-a mais estressante para a cultura que a colheita manual. Diante disso, o presente trabalho foi realizado no município de Patos de Minas, MG, com o objetivo de avaliar os danos na parte vegetativa e a qualidade da colheita mecanizada do café cultivado em plantio circular sob pivô central, com duas frequências de vibração das hastes, sob o controle estatístico do processo. Observou-se que a bienalidade negativa sobre a cultura reduziram a carga inicial de café, eliminando o efeito das condições de insolação. Os índices de qualidade da colheita apresentaram distribuição assimétrica, com grande variabilidade nas amostras, sendo apenas a eficiência de derriça influenciada pelos eixos avaliados, e se mostrando estável pelo controle estatístico. Os danos causados às plantas pela colheita apresentaram valores desejáveis, não variando em função dos fatores analisados, mas sendo considerado sob controle estatístico.

A class of multiobjective control problems

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

X̄ charts with variable sample size

The usual practice in using a control chart to monitor a process is to take samples of size n from the process every h hours. This article considers the properties of the X̄ chart when the size of each sample depends on what is observed in the preceding sample. The idea is that the sample should be large if the sample point of the preceding sample is close to but not actually outside the control limits and small if the sample point is close to the target. The properties of the variable sample size (VSS) X̄ chart are obtained using Markov chains. The VSS X̄ chart is substantially quicker than the traditional X̄ chart in detecting moderate shifts in the process.

The no-central chi-square chart with two-stage samplings

Throughout this article, it is assumed that the no-central chi-square chart with two stage samplings (TSS Chisquare chart) is employed to monitor a process where the observations from the quality characteristic of interest X are independent and identically normally distributed with mean μ and variance σ2. The process is considered to start with the mean and the variance on target (μ = μ0; σ2 = σ0 2), but at some random time in the future an assignable cause shifts the mean from μ0 to μ1 = μ0 ± δσ0, δ >0 and/or increases the variance from σ0 2 to σ1 2 = γ2σ0 2, γ > 1. Before the assignable cause occurrence, the process is considered to be in a state of statistical control (defined by the in-control state). Similar to the Shewhart charts, samples of size n 0+ 1 are taken from the process at regular time intervals. The samplings are performed in two stages. At the first stage, the first item of the i-th sample is inspected. If its X value, say Xil, is close to the target value (|Xil-μ0|< w0σ 0, w0>0), then the sampling is interrupted. Otherwise, at the second stage, the remaining n0 items are inspected and the following statistic is computed. Wt = Σj=2n 0+1(Xij - μ0 + ξiσ 0)2 i = 1,2 Let d be a positive constant then ξ, =d if Xil > 0 ; otherwise ξi =-d. A signal is given at sample i if |Xil-μ0| > w0σ 0 and W1 > knia:tl, where kChi is the factor used in determining the upper control limit for the non-central chi-square chart. If devices such as go and no-go gauges can be considered, then measurements are not required except when the sampling goes to the second stage. Let P be the probability of deciding that the process is in control and P 1, i=1,2, be the probability of deciding that the process is in control at stage / of the sampling procedure. Thus P = P1 + P 2 - P1P2, P1 = Pr[μ0 - w0σ0 ≤ X ≤ μ0+ w 0σ0] P2=Pr[W ≤ kChi σ0 2], (3) During the in-control period, W / σ0 2 is distributed as a non-central chi-square distribution with n0 degrees of freedom and a non-centrality parameter λ0 = n0d2, i.e. W / σ0 2 - xn0 22 (λ0) During the out-of-control period, W / σ1 2 is distributed as a non-central chi-square distribution with n0 degrees of freedom and a non-centrality parameter λ1 = n0(δ + ξ)2 / γ2 The effectiveness of a control chart in detecting a process change can be measured by the average run length (ARL), which is the speed with which a control chart detects process shifts. The ARL for the proposed chart is easily determined because in this case, the number of samples before a signal is a geometrically distributed random variable with parameter 1-P, that is, ARL = I /(1-P). It is shown that the performance of the proposed chart is better than the joint X̄ and R charts, Furthermore, if the TSS Chi-square chart is used for monitoring diameters, volumes, weights, etc., then appropriate devices, such as go-no-go gauges can be used to decide if the sampling should go to the second stage or not. When the process is stable, and the joint X̄ and R charts are in use, the monitoring becomes monotonous because rarely an X̄ or R value fall outside the control limits. The natural consequence is the user to pay less and less attention to the steps required to obtain the X̄ and R value. In some cases, this lack of attention can result in serious mistakes. The TSS Chi-square chart has the advantage that most of the samplings are interrupted, consequently, most of the time the user will be working with attributes. Our experience shows that the inspection of one item by attribute is much less monotonous than measuring four or five items at each sampling.

Quality of performance of the operation of sugarcane mechanized planting in day and night shifts

The sugarcane mechanized planting is becoming increasingly widespread in Brazil due to a higher operability and better working conditions offered to workers compared to other types of planting. Studies related to this topic are insufficient or scarce in Brazil. In this context, the aim of this study was to evaluate the operation quality of sugarcane mechanized planting in two operation shifts, by means of statistical process control. The mechanized planting was held on March 2012 and statistical design was completely randomized with two treatments, totaling 40 replications for the day shift and 40 replications for the night shift. The variables evaluated were: speed, engine rotation, engine oil pressure, water temperature of the engine, effective field capacity and the time consumption hourly and effective fuel. The use of statistical control charts showed that random intrinsic do not cause this process. The tractor alignment error showed outliers in the day and night shifts operations, indicating a possible delay in receiving the signal. The water temperature of the engine and the effective fuel consumption showed lower variability in nighttime operation with average values of 81°C and 22.66 L ha-1, respectively. The hourly fuel consumption had greater variability and consequently lower quality during the night of the operation, with an average consumption of 25.46 L h-1 while the day shift showed 26.86 L h-1.

Variabilidade espacial e diagnóstico da qualidade do processo em semeadura de amendoim

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise da variabilidade do processo de filtração em filtros de tambor rotativo contínuo a vácuo para lodo de caldo de cana de açúcar

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)