Carotid arterial plaque stress analysis using fluid-structure interactive simulation based on in-vivo magnetic resonance images of four patients

The rupture of atherosclerotic plaques is known to be associated with the stresses that act on or within the arterial wall. The extreme wall tensile stress (WTS) is usually recognized as a primary trigger for the rupture of vulnerable plaque. The present study used the in-vivo high-resolution multi-spectral magnetic resonance imaging (MRI) for carotid arterial plaque morphology reconstruction. Image segmentation of different plaque components was based on the multi-spectral MRI and co-registered with different sequences for the patient. Stress analysis was performed on totally four subjects with different plaque burden by fluid-structure interaction (FSI) simulations. Wall shear stress distributions are highly related to the degree of stenosis, while the level of its magnitude is much lower than the WTS in the fibrous cap. WTS is higher in the luminal wall and lower at the outer wall, with the lowest stress at the lipid region. Local stress concentrations are well confined in the thinner fibrous cap region, and usually locating in the plaque shoulder; the introduction of relative stress variation during a cycle in the fibrous cap can be a potential indicator for plaque fatigue process in the thin fibrous cap. According to stress analysis of the four subjects, a risk assessment in terms of mechanical factors could be made, which may be helpful in clinical practice. However, more subjects with patient specific analysis are desirable for plaque-stability study.

Desarrollo de nanopartículas sólidas lipídicas como sistemas de administración de ADN para terapia génica

290 p. (Bibliogr. 257-290) Correo electrónico de la autora: ana.delpozo@ehu.es

内蒙古锡林河流域草原植物和群落热值的时空变异研究

第一部分：内蒙古锡林河流域草原植物种群和群落热值的时空变异研究 热值的研究是评价生态系统能量固定、传输和转化的基础，也是评价植物光合作用效率和植物营养值的有用参数。同种植物热值会随着植物部位、光照、养分条件、季节、土壤类型和气候条件的不同而发生变化。不同的种类和类群之间热值也存在差异。本项研究以内蒙古锡林河流域中段草原植物群落为对象，研究了植物种群和群落热值的时空变异规律。 对内蒙古羊草草原群落不同植物种群热值的时问动态研究结果表明，42种植物地上部分的热值在13.16土1.14 kJ.g-l和18.14土0.53 kJ.g-1之间变动，所有物种的平均热值为16.90土0,84 kJ.g-1，种间变异系数4.9%。小叶锦鸡儿(Caraganamicrophylla)具有最高的热值。禾草的平均热值高于杂草。根据生活型和生长型，草本物种被进一步分组，热值从高到低的排列顺序为：高禾草>豆科植物>矮禾草>其余杂草>半灌木>一二年生植物。 主要植物种群地下部分热值的分布范围为15.05-16.41 kJ.g-1。其中根茎型草地下部分热值较高。不同种类植物地下部分热值差异并不与地上部分一致。根茎型禾草地上、地下部分热值差异较小，而须根型植物差异较大。不同种群的植物地上部分热值随植物物候期的不同而波动，其变化规律是与植物种群本身的生物学特性相联系的。不同植物种群热值的年际波动规律有所不同，羊草(Leymuschinensis)、大针茅(Stipa grandis)和洽草(Koeloria cristata)的年际热值波动相关显著，但与生长季降水量和生长季累积日照时数之间无明显相关性。在某种程度上，植物热值的种内变化反映了植物生长状况的差异。 42种植物的热值和它们在群落中的相对生物量存在显著正相关关系。表现为优势种(17.74 kJ.g-1)>伴生种(17.24 kJ．g-l)>偶见种(16.65 kJ.g-1)。高热值的植物更具竞争力，在群落中通常占据优势地位，而低热值的植物竞争力通常较弱，构成草原群落的伴生种或偶见种。 以内蒙古锡林河流域3个草原群落类型（羊草典型草原，大针茅典型草原，羊草草甸草原）的放牧退化梯度系列（包括未退化，轻度退化，中度退化和重度退化4个强度）为研究对象，对主要植物种群和群落热值随草原类型和退化梯度的空间变异规律及热值与其他群落和土壤性质的相关性进行了研究。 结果表明，研究区出现的60个植物种平均热值为17.25土0.92 kJ.g-1，变异系数5.4%．热值大于18.00 kJ.g-1的高能植物包括3种优势高禾草(羊草、大针茅和羽茅(A. sibiricum))和一些有毒植物，热值小于17.00 kJ.g-1的低能值植物包括多数一年生杂草;热值在17.00-18.00 kJ.g-1之间的中能值植物包括大多数多年生杂草和矮禾草。 按照生活型分类，灌木的热值最高，多年生禾草显著高于一二年生植物，半灌木和多年生杂草介于二者之间。按照水分生态类型分类，旱生植物、中旱生、旱中生和中生植物之间在热值上没有明显差异。不同科之间热值存在显著差异，禾本科、豆科、菊科植物热值较高，藜科植物平均热值最低。 二因素方差分析结果表明，主要优势物种热值在不同草原类型之间存在显著差异，表现为羊草草甸草原>羊草典型草原>大针茅典型草原。对于大多数优势禾草，热值没有随退化梯度发生明显变化，洽草(K. cristata)、冰草(A．ctistatum)和所有优势杂草随退化程度的增强热值趋于下降。对于大多数优势物种，热值随不同草原类型的空间变异大于放牧退化所导致的空间变异。 不同草原类型的群落热值为羊草草甸草原>羊草典型草原>大针茅典型草原，群落平均热值表现出随退化强度的增加而下降的趋势，这主要归因于沿退化梯度不同物种构成比例的变化，即随退化程度的加剧，高能值植物在群落中的比例下降。其次是特定物种热值随退化梯度的变化。在同一草原区，放牧对群落热值的影响大于立地条件之间的差异。 群落和主要物种热值均表现出与某些群落特征和土壤性质的相关性。 关键词：内蒙古，锡林河流域，羊草草原;物种和群落热值，时空变异，退化梯度，草原类型，土壤性质 第二部分内蒙古羊草草原17年刈割演替过程中功能群组成动态及其对群落净初级生产力稳定性的影响 基于17年的野外实验数据，研究了内蒙古羊草草原群落刈割演替过程中的功能群组成动态，探索功能群组成变化与群落净初级生产力(ANPP)之间的关系，分析结构参数怎样影响功能参数。结果显示：在17年的割草演替过程中，群落的结构与功能均发生了变化。随着羊草群落刈割演替的进行，群落的功能群组成发生了显著变化，根茎禾草在群落中的优势地位相继被一二年生植物，高丛生禾草，矮丛生禾草所取代。到17年末，群落变成根茎禾草，矮丛生禾草，高丛生禾草共同建群的群落。在对照群落中ANPP与年降水量显著相关，但在刈割群落中二者则不相关。年降水量解释对照群落ANPP变异的62%，而连年的刈割干扰则是刈割群落中ANPP动态的主要驱动因子。群落净初级生产则显出对刈割干扰的抵抗能力，在刈割干扰的前几年，依靠群落内功能群组成的不断调节，保持相对稳定的水平，当刈割进行5年之后，群落结构的变化积累到一定程度，净初级生产迅速下降到一个较低的水平，此后依靠群落结构的不断调节来维持这一功能水平。因此，群落结构是以渐变的方式改变的，而群落功能的下降则是以跃变的形式完成的。群落依赖于结构的不断调整来保持功能的相对稳定，但结构变化到一定程度也会导致功能的衰退。 关键词：内蒙古，羊草草原;刈割演替;功能群组成;净初级生产;群落;稳定性

层状反倾向结构岩质边坡变形机理及稳定性研究

Toppling is a major failure model in anti-dip layered rock slopes. Because of the limited by testing means and experimental apparatus, present research on the deformation mechanism and stability analysis are mainly focus on the 2-Dimensional deformation, and the research really based on 3-Dimension is still limited. Therefore, based on the present research station, the article rely on the important hydroelectric project of typical anti-dip layered rock slopes -- The left bank slope of Long-tan hydropower-station in Guang Xi, China, and focused on the influencing factors, deformation mechanism and stability analysis of anti-dip layered rock slopes, three problems as follows are researched in this paper. (1) Deformation influencing factor analysis on ant-dip layered rock slopes Three influencing factors are included: geological factor, engineering factor and environmental factor. It is concluded that the toppling deformation of anti-dip layered rock slopes are more sensitive to geological and engineering factors, but less sensitive to environmental factor. In addition, the sensitivity of various factors to the rock toppling deformation is also arranged sequentially as follows: construction, gravitation, rainfall (underground water) and rock structure intensity, etc. (2) 3D deformation study on the anti-dip layered toppling rock slopes Used 3D Distinct Element Method (3DEC) analyzed the 3D deformation characteristic of anti-dip layered rock slops. It can be seen that the toppling characteristics are obvious when the inter-angle between slope direction and layer striking direction is under 20o, when the inter-angle is over 20o and equal or less than 40o，the toppling deformation characteristics decrease sharply with increase of inter-angle, when the inter-angle is over 40o , the slope deformation is not controlled by joints but influenced by other failure mode. Therefore, in order to quantify the toppling characteristics, a differential value of displacement vector angle between layered rock slope and block rock slope is proposed as a key index to distinguish failure model for anti-dip layered rock slopes, and it was applied to study the toppling of the rock slopes at Guangxi Long-tan hydropower station, China. The results indicated that the index was effective and instructive for analyzing the anti-dip layered rock slopes. (3) Stability analysis methods Because of the imperfection of some present slope analysis methods, based on slope failure mode and those three influencing factors, “slope stability entropy” method is defined in this paper, which makes good use of the sensitivity of relational matrix to influencing factors on slope stability and the qualification characteristics for information entropy to the irregularity of slope deformation. By this method, not only the randomness of geologic body on the base of dynamic analysis of slope failure mode is fully concerned, but also it makes the analysis time-saving and simple. Finally, the research findings were used to the engineering example successfully, and rational conclusion has been obtained.

大型反倾岩体变形破坏机制及稳定性分析———以金沙江宽谷坝址龙蟠边坡为例

A large number of catastrophic accidents were aroused by the instability and destruction of anti-dip rock masses in the worldwide engineering projects, such as hydropower station, mine, railways and so on. Problems in relation to deformation and failure about anti-dip rock slopes are significant for engineering geology research. This dissertation takes the Longpan slope in the Jinsha River as a case to study the deformation mechanism of large-scale anti-dip rock masses and the slope stability analysis method. The primary conclusions are as follows. The Dale Reach of Jinsha River, from Longpan to the debouchment of Chongjiang tributary, is located in the southeastern margin of the Qinghai-Tibet Plateau. Longpan slope is the right embankment of Dale dam, it is only 26 km to the Shigu and 18 km to Tiger Leaping Gorge. The areal geology tectonic structures here area are complicated and blurry. Base on the information of geophysical exploration (CSAMT and seismology) and engineering geological investigation, the perdue tectonic pattern of Dale Reach is put forward for the first time in this paper. Due to the reverse slip of Longpan fault and normal left-rotation of Baihanchang fault, the old faulted valley came into being. The thick riverbed sediments have layered characters of different components and corresponding causes, which attribute to the sedimentary environments according with the new tectonic movements such as periodic mountain uplifting in middle Pleistocene. Longpan slope consists of anti-dip alternate sandstone and slate stratums, and the deformable volume is 6.5×107m3 approximately. It was taken for an ancient landslide or toppling failure in the past so that Dale dam became a vexed question. Through the latest field surveying, displacement monitoring and rock masses deforming characters analyses, the geological mechanism is actually a deep-seated gravitational bending deformation. And then the discrete element method is used to simulate the deforming evolution process, the conclusion accords very well with the geo-mechanical patterns analyses. In addition strength reduction method based on DEM is introduced to evaluate the factor of safety of anti-dip rock slope, and in accordance with the expansion way of the shear yielding zones, the progressive shear failure mechanism of large-scale anti-dip rock masses is proposed for the first time. As an embankment or a close reservoir bank to the lower dam, the stability of Longpan slope especially whether or not resulting in sliding with high velocity and activating water waves is a key question for engineering design. In fact it is difficult to decide the unified slip surface of anti-dip rock slope for traditional methods. The author takes the shear yielding zones acquired form the discrete element strength reduction calculation as the potential sliding surface and then evaluates the change of excess pore pressure and factor of stability of the slope generated by rapid drawdown of ponded water. At the same time the dynamic response of the slope under seismic loading is simulated through DEM numerical modeling, the following results are obtained. Firstly the effective effect of seismic inertia force is resulting in accumulation of shear stresses. Secondly the discontinuous structures are crucial to wave transmission. Thirdly the ultimate dynamic response of slope system takes place at the initial period of seismic loading. Lastly but essentially the effect of earthquake load to bringing on deformation and failure of rock slope is the coupling effect of shear stresses and excess pore water pressure accumulation. In view of limitations in searching the critical slip surface of rock slope of the existing domestic and international software for limit equilibrium slope stability analyses, this article proposes a new method named GA-Sarma Algorithm for rock slope stability analyses. Just as its name implies, GA-Sarma Algorithm bases on Genetic Algorithm and Sarma method. GA-Sarma Algorithm assumes the morphology of slip surface to be a broken line with traceability to extend along the discontinuous surface structures, and the slice boundaries is consistent with rock mass discontinuities such as rock layers, faults, cracks, and so on. GA-Sarma Algorithm is revolutionary method that is suitable for global optimization of the critical slip surface for rock slopes. The topics and contents including in this dissertation are closely related to the difficulties in practice, the main conclusions have been authorized by the engineering design institute. The research work is very meaningful and useful for the engineering construction of Longpan hydropower station.

土石混合体细观结构力学及其边坡稳定性研究

Soil-rock mixture (S-RM) refers to one extremely uneven loose rock and soil materials system with certain stone content. Its formation has started since Quaternary and it is composed of block stone, fine grained soil and pore with certain project scale and high strength. S-RM has extensive distribution in nature, especially in southwest China where the geotectonic background is complicated, the fracture activity is developed and the geomorphological characteristics of high mountain and steep gorge area are protuberant. This kind of complicated geologic body has developed wider in these areas. S-RM has obvious difference with the general soil or rock (rock mass) in physical and mechanical properties because its two components-“soil” and “rock-block” has extreme differences in physical and mechanical properties. The proposition of S-RM and its deep research are needed in the modern engineering construction. It is also the necessity in the modern development of rock and soil mechanics. The dissertation starts from the meso-structural characteristics of soil-rock and takes a systematic research on its meso-structural mechanics, deformation and failure mechanism and the stability of S-RM slope. In summary, it achieves the following innovative results and conclusions. There are various views on the conception of S-RM and its classification system. Based on the large number of field tests, the dissertation makes the conception and classification of S-RM more systematic. It systematically proposed the conception of meso-structural mechanics of S-RM. Thus the dissertation has laid a foundation for its deep study. With the fast development of the computer technology and digital image processing theory, digital image processing technology has been successfully applied in many fields and provided reliable technology support for the quantitative description of the structural characteristics of S-RM. Based on the digital image processing technology, the dissertation systematically proposes and developed the quantitative analysis method and quantitative index for the meso-structure of S-RM. The results indicate that the meso-structure such as its internal soil-rock granularity composition, the soil-rock shape and the orientability has obvious self-organization in the macro statistical level. The dissertation makes a systematic research on the physical mechanical properties, deformation and failure mechanism of S-RM based on large field test. It proposes the field test for the underwater S-RM and deduces the 3D data analysis method of in-situ horizontal push-shear test. The result indicates that S-RM has significant phenomenon of shear dilatancy in the shearing process, and its dilatancy will be more obvious with the increased proportion of rock or the decreased confining pressure. The proportion of rock has great effect on the strength of S-RM and rock-block, especially the spatial position of particles with comparatively big size has great effect on the shape and spatial position of the sample shear zone. The dissertation makes some improvements in the single ring infiltration test equipment and its application on the permeability of S-RM. The results indicate that the increasing of rock-block would make it more difficult for the soil to fill in the vacuity between the rock-block and the proportion would increase which would result in the increased permeability coefficient. The dissertation builds the real meso-structural model of S-RM based on the digital image processing technology. By using geometric reconstruction technology, it transfers the structural mode represented by Binary image into CAD format, which makes it possible to introduce the present finite element analysis software to take research on numerical experimental investigation. It systematically realizes leaping research from the image，geometric mode, to meso-structural mechanics numerical experiment. By using this method, the dissertation takes large scale numerical direct-shear test on the section of S-RM. From the mesoscopic perspective, it reveals three extended modes about the shear failure plane of S-RM. Based on the real meso-structural model and by using the numerical simulation test, the character and mechanics of seepage failure of S-RM are studied. At the same time, it builds the real structural mode of the slope based on the analysis about the slope crosssection of S-RM. By using the strength reduction method, it takes the research on the stability of S-RM and gets great achievements. The three dimensional geometric reconstruction technology of rock block is proposed, which provides technical support for the reconstruction of the 3D meso-structural model of S-RM. For the first time, the dissertation builds the stochastic structure model of two-dimensional and three-dimensional polygons or polyhedron based on the stochastic simulation technique of monte carlo method. It breaks the traditional research which restricted to the random generation method of regular polygon and develops the relevant software system (R-SRM2D/3D) which has great effect on meso-structural mechanics of S-RM. Based on the R-SRM software system which randomly generates the meso-structural mode of S-RM according to the different meso-structural characteristics, the dissertation takes a series of research on numerical test of dual axis and real three-axis, systematically analyses the meso destroy system, the effects of meso-structural characteristics such as on the stone content, size composition and block directionality on the macro mechanical behavior and macro-permeability. Then it proposes the expression of the upper and lower limit for the macro-permeability coefficient of the inhomogeneous geomaterials, such as S-RM. By using the strength reduction FEM, the dissertation takes the research on the stability of the slope structural mode of the randomly formed S-RM. The results indicate that generally, the stability coefficient of S-RM slope increases with the increasing of stone content; on the condition of the same stone content, the stability coefficient of slope will be different with different size composition and the space position of large block at the internal slop has great effect on the stability. It suggests that meso-structural characteristics, especially the space position of large block should be considered when analyzing the stability of this kind of slope and strengthening design. Taking Xiazanri S-RM slope as an example, the dissertation proposes the fine modeling of complicated geologic body based on reverse engineering and the generation method of FLAC3D mode. It resolves the bottleneck problem about building the fine structural mode of three-dimensional geological body. By using FLAC3D, the dissertation takes research on the seepage field and the displacement field of Xiazanri S-RM slope in the process of reservoir water level rising and decreasing. By using strength reduction method, it analyses the three-dimension stability in the process of reservoir water level rising and decreasing. The results indicate that the slope stability firstly show downward trend in the process of reservoir water level rising and then rebound to increase; the sudden drawdown of reservoir water level has great effect on the slope stability and this effect will increase with the sudden drawdown amplitude rising. Based on the result of the rock block size analysis of S-RM, and using R-SRM2D the stochastic structure model of Xiazanri S-RM slope is built. By using strength reduction method, the stability of the stochastic structure model is analysis, the results shows that the stability factor increases significantly after considering the block.

边坡动力响应分析及应用研究

As a marginal subject, dynamic responses of slopes is not only an important problem of engineering geology (Geotechnical problem), but also of other subjects such as seismology, geophysics, seismic engineering and engineering seismic and so on. Owning to the gulf between different subjects, it is arduous to study dynamic responses of slopes and the study is far from ripeness. Studying on the dynamic responses of slopes is very important in theories as well as practices. Supported by hundreds of bibliographies, this paper systemically details the development process of this subject, introduces main means to analyze this subject, and then gives brief remarks to each means respectively. Engineering geology qualitative analysis is the base of slopes dynamic responses study. Because of complexity of geological conditions, engineering geology qualitative analysis is very important in slopes stability study, especially to rock slopes with complex engineering geology conditions. Based on research fruits of forerunners, this paper summarizes factors influencing slopes dynamic stability into five aspects as geology background, stratums, rock mass structure, and topography as well as hydrogeology condition. Based on rock mass structure controlling theory, engineering geology model of the slope is grouped into two typical classes, one is model with obvious controlling discontinuities, which includes horizontal bedded slope, bedding slope, anti-dip slope, slide as well as slope with base rock and weathered crust; the other is model without obvious controlling discontinuities, which includes homogeneous soil slope, joint rock mass slope. Study on slope failure mechanism under dynamic force, the paper concludes that there are two effects will appear in slope during strong earthquake, one is earthquake inertia force, the other is ultra pore pressure buildup. The two effects lead to failure of the slope. To different types of slope failure, the intensity of two effects acting on the slope is different too. To plastic flow failure, pore pressure buildup is dominant; to falling rock failure and toppling failure, earthquake inertia force is dominant in general. This paper briefly introduces the principle of Lagrangian element method. Through a lot of numerical simulations with FLAC3D, the paper comprehensively studies dynamic responses of slopes, and finds that: if the slope is low, displacement, velocity and acceleration are linear enlarging with elevation increasing in vertical direction; if the slope is high enough, displacement, velocity and acceleration are not linear with elevation any more, on the other hand, they fluctuate with certain rhythm. At the same time, the rhythm appears in the horizontal direction in the certain area near surface of the slope. The distribution form of isoline of displacement, velocity and acceleration in the section of the slope is remarkably affected by the slope angle. In the certain area near the slope surface, isoline of displacement, velocity and acceleration is parallel to the surface of the slope, in the mean time, the strike direction of the extreraum area is parallel to the surface of the slope too. Beyond this area, the isoline direction and the strike direction of the extremum area turn to horizontal with invariable distance. But the rhythm appearing or not has nothing to with the slope angle. The paper defines the high slope effect and the low slope effect of slopes dynamic responses, discusses the threshold height H^t of the dynamic high slope effect, and finds that AW is proportional to square root of the dynamic elastic moduli El P , at the same time, it is proportional to period Tof the dynamic input. Thus, the discriminant of H^t is achieved. The discriminant can tell us that to a slope, if its height is larger than one fifth of the wavelength, its response regular will be the dynamic high slope effect; on the other hand, its response regular will be the dynamic low slope effect. Based on these, the discriminant of different slopes taking on same response under the same dynamic input is put forward in this paper. At the same time, the paper studies distribution law of the rhythm extremum point of displacement, velocity and acceleration, and finds that there exists relationship of N = int among the slope height H, the number of the rhythm extremum VHlhro) point N and ffthre- Furthermore, the paper points out that if N^l, the response of the slope will be dynamic high slope effect; \fNstability of the slope is a key engineering geological problem. The paper studies the dynamic stability of the slope. In the analysis, considering regional geology and regional seismology of the slope, combining with characteristics of the slope as well as the scale of the project, PGA(peak ground acceleration) of the site is decided (about 197.1cm/s2) by engineering seismology, and then the seismic input used in the slope dynamic analysis is determined. Comprehensive studies are carried out on the slope, especially to its deep fractures, and then the paper concludes that the deep fractures of slope are the result of the combination unloading effect of gravity and tectonic stress. At the same time, the failure model of the slope under dynamic input is attained. Based on these, the stability is comprehensively studied for section IV-IV with numerical simulation method as well as method putting forward in chapter 5. At last, the paper concludes that under dynamic input, the section will slide along fault f9, some deep fractures and fault/5 with certain permanent displacement, and this must be taken into consideration in the engineering.

Development and validation of the first high performance-lateral flow immunoassay (HP-LFIA) for the rapid screening of domoic acid from shellfish extracts

A lateral flow immunoassay (LFIA) has been developed and fully validated to detect the primary amnesic shellfish poisoning (ASP) toxin, domoic acid (DA). The performance characteristics of two versions of the test were investigated using spiked and naturally contaminated shellfish (mussels, scallops, oysters, clams, and cockles). The tests provide a qualitative result, to indicate the absence or presence of DA in extracts of shellfish tissues, at concentrations that are relevant to regulatory limits. The new rapid assay (LFIA version 2) was designed to overcome the performance limitations identified in the first version of the assay. The improved test uses an electronic reader to remove the subjective nature of the generated results, and the positive cut-off for screening of DA in shellfish was increased from 10 ppm (version 1) to 17.5 ppm (version 2). A simple extraction and test procedure was employed, which required minimal equipment and materials; results were available 15 min after sample preparation. Stability of the aqueous extracts at room temperature (22 C) at four time points (up to 245 min after extraction) and across a range of DA concentrations was 100.3±1.3% and 98.8±2.4% for pre- and post-buffered extracts, respectively. The assay can be used both within laboratory settings and in remote locations. The accuracy of the new assay, to indicate negative results at or below 10 ppm DA, and positive results at or above 17.5 ppm, was 99.5% (n=216 tests). Validation data were obtained from a 2-day, randomised, blind study consisting of multiple LFIA lots (n=3), readers (n=3) and operators (n=3), carrying out multiple extractions of mussel tissue (n=3) at each concentration (0, 10, 17.5, and 20 ppm). No matrix effects were observed on the performance of the assay with different species (mussels, scallops, oysters, clams, and cockles). There was no impact on accuracy or interference from other phycotoxins, glutamic acid or glutamine with various strip incubations (8, 10, and 12 min). The accuracy of the assay, using naturally contaminated samples to indicate negative results at or below 12.5 ppm and positive results at or above 17.5 ppm, was 100%. Variability between three LFIA lots across a range of DA concentrations, expressed as coefficient of variation (% CV), was 1.1±0.4% (n=2 days) based on quantitative readings from the electronic reader. During an 8 week stability study, accuracy of the method with test strips stored at various temperatures (6, 22, 37 and 50 C) was 100%. Validation for both versions included comparisons with results obtained using reference LC-UV methods. © 2013 Elsevier B.V.

Préparations de docosanol nanoformulées pour usage topique

La réduction de la taille des particules jusqu’à l’obtention de nanocristaux est l’une des approches utilisées afin d’améliorer la pénétration cutanée des médicaments à usage topique. Nous proposons que la fabrication d’une formulation semi solide (hydrogel) à base de nanosuspension de docosanol, aboutira à une diffusion du principe actif supérieure à celle du produit commercial Abreva®, à travers des membranes synthétiques de polycarbonates. Le broyage humide est la technique proposée pour la production des nanoparticules de docosanol. Nous proposons aussi la préparation d’une formulation semi-solide (hydrogel) à usage topique à partir de la nanosuspension de docosanol. La nanosuspension de docosanol est obtenue par dispersion du docosanol en solution aqueuse en présence du polymère stabilisant hydroxypropylcellulose (HPC) et du surfactant laurylsulfate de sodium (SDS) suivi d’un broyage humide à faible ou à haute énergie. L’hydrogel de docosanol nanoformulé est préparé à l’aide de la nanosuspension de docosanol qui subit une gélification par le carbopol Ultrez 21 sous agitation mécanique suivie d’une neutralisation au triéthanolamine TEA. La taille des particules de la nanosuspension et de l’hydrogel a été déterminée par diffusion dynamique de la lumière (DLS). Une méthode analytique de chromatographie liquide à haute performance (HPLC) munie d’un détecteur évaporatif (ELSD) a été développée et validée pour évaluer la teneur de docosanol dans les préparations liquides, dans les différentes nanosuspensions et dans les hydrogels de docosanol. L’état de cristallinité des nanocristaux dans la nanosuspension et dans l’hydrogel a été étudié par calorimétrie différentielle à balayage. La morphologie de la nanosuspension et de l’hydrogel de docosanol a été examinée par microscopie électronique à balayage (MEB). Les propriétés rhéologiques et de stabilité physique à différentes températures ont été aussi étudiées pour la formulation semi-solide (hydrogel). De même, la libération in vitro du docosanol contenu dans l’hydrogel et dans le produit commercial Abreva® a été étudiée à travers deux membranes de polycarbonates de taille de pores 400 et 800 nm. Dans le cas de nanosuspensions, des cristaux de docosanol de taille nanométrique ont été produits avec succès par broyage humide. Les nanoparticules de tailles variant de 197 nm à 312 nm ont été produites pour des pourcentages différents en docosanol, en polymère HPC et en surfactant SDS. Après lyophilisation, une augmentation de la taille dépendant de la composition de la formulation a été observée tout en restant dans la gamme nanométrique pour la totalité presque des formulations étudiées. Dans le cas des hydrogels examinés, la taille moyenne des particules de docosanol est maintenue dans la gamme nanométrique avant et après lyophilisation. L’analyse thermique des mélanges physiques, des nanosuspensions et des hydrogels de docosanol a révélé la conservation de l’état de cristallinité des nanocristaux de docosanol après broyage et aussi après gélification. L’examen par microscopie électronique à balayage (MEB) a montré que la nanosuspension et l’hydrogel ont tous deux une morphologie régulière et les nanoparticules ont une forme sphérique. De plus les nanoparticules de la nanosuspension ont presque la même taille inférieure à 300 nm en accord avec le résultat obtenu par diffusion dynamique de la lumière (DLS). Les nanoparticules de l’hydrogel ont une légère augmentation de taille par rapport à celle de la nanosuspension, ce qui est en accord avec les mesures de DLS. D’après les mesures rhéologiques, l’hydrogel de docosanol a un comportement pseudoplastique et un faible degré de thixotropie. L’étude de stabilité physique a montré que les formulations d’hydrogel sont stables à basse température (5°C) et à température ambiante (21°C) pendant une période d’incubation de 13 semaines et instable au-delà de 30°C après deux semaines. La méthode HPLC-ELSD a révélé des teneurs en docosanol comprises entre 90% et 110% dans le cas des nanosuspensions et aux alentours de 100% dans le cas de l’hydrogel. L’essai de diffusion in vitro a montré qu’il y a diffusion de docosanol de l’hydrogel à travers les membranes de polycarbonates, qui est plus marquée pour celle de pore 800 nm, tandis que celui du produit commercial Abreva® ne diffuse pas. Le broyage humide est une technique bien adaptée pour la préparation des nanosuspensions docosanol. Ces nanosuspensions peuvent être utilisée comme base pour la préparation de l’hydrogel de docosanol nanoformulé.

Administration de [6]-gingérol intrathécal pour le traitement de la douleur neuropathique chez le rat mâle Sprague-Dawley

Le [6]-gingérol est un analogue structurel de la capsaïcine, une molécule agoniste au récepteurs TRPV1 et ayant des propriétés thérapeutiques connues dans le traitement de la douleur. Deux objectifs principaux ont été poursuivis lors de la réalisation de ce projet de recherche. D’abord, établir une meilleure caractérisation du métabolisme du [6]-gingérol chez le rat. Pour ce faire, une méthode sensible et spécifique pour la quantification du [6]-gingérol et ses métabolites par HPLC-ESI/MS/MS a été développée. Une étude de stabilité métabolique in vitro utilisant des microsomes hépatiques de rats a ensuite été réalisée. Les résultats démontrent une dégradation lente avec un temps de demi-vie de 163 minutes et une clairance intrinsèque relativement basse de 0.0043 mL/min. D’autres analyses ont ensuite été performées pour caractériser les métabolites in vitro et in vivo. Trois principaux métabolites de phase I et quatre métabolites de phase II ont été identifiés par HPLC-MS/MS et HPLC-MSD TOF. Les résultats suggèrent que le principal métabolite excrété dans l’urine est un glucuronide du [6]-gingérol hydroxylé. Le second objectif de ce projet était de déterminer l’effet central du [6]-gingérol sur la douleur neuropathique lorsqu’injecté par voie intrathécale. La distribution de la molécule a d’abord été évaluée suite à une administration intra-péritonéale de 40 mg/kg de [6]-gingérol et les ratios des concentrations cerveau-plasma et moelle épinière-plasma (0.73 et 1.7, respectivement) suggèrent que le [6]-gingérol se distribue efficacement au niveau du système nerveux central. Une injection intrathécale de 10 μg de [6]-gingérol à été performée chez les rats suite à l’induction de douleur par la pose de ligatures au niveau du nerf sciatique. Les résultats suggèrent une réduction significative de l’allodynie mécanique et de l’hyperalgésie thermique à 30 min, 2 h et 4 h suivant l’injection (p < 0.05, p < 0.01 et p < 0.001). Le [6]-gingérol se distribue donc adéquatement au niveau du système nerveux central des rats, permettant une action au niveau des récepteurs TRPV1. Ainsi, le [6]-gingérol pourrait soulager la douleur neuropathique en agissant centralement au niveau de la moelle épinière.

Estabilidade e eficácia de fotoprotetores contendo filtros inorgânicos e quercetina

A exposição ao sol traz benefícios à saúde, no entanto, o excesso pode ocasionar danos cutâneos dentre os quais se destacam as neoplasias. A fotoproteção é um método para a prevenção dos efeitos danosos da radiação ultravioleta (UV) e a biodiversidade Brasileira é campo fértil para pesquisas nesta área. Dessa forma, os objetivos deste estudo envolveram o desenvolvimento de formulações fotoprotetoras contendo quercetina (composto bioativo) e filtros solares físicos (dióxido de titânio e óxido de zinco), com posterior caracterização das formulações e avaliação da sua estabilidade. As formulações contendo o composto bioativo, isolado ou em associação com os filtros físicos, possuíram valores de pH biocompatíveis com a pele,intervalo de viscosidade aparente entre 10550 e 23600 cP; fator de proteção solar (FPS) estimado entre 2.1 e 22.5; e amplo espectro de proteção, com comprimentos de onda crítico acima de 379 nm. Constatou-se que não foi adequado utilizar a quercetina associada aos filtros solares físicos devido às interações negativas que ocorreram entre o composto e os metais, somente identificadas ao longo do estudo de estabilidade. No entanto, em função da eficácia estimada in vitro apresentada pelo flavonoide, seu uso ainda pode ser explorado como substituto alternativo aos filtros solares clássicos.

Análise botânica, química e biológica comparativa entre flores das espécies sambucus nigra L. e sambucus australis cham. & Schltdt. e avaliação preliminar da estabilidade

Flores das espécies Sambucus nigra, de origem européia, e Sambucus australis, nativa da América do Sul (Caprifoliaceae), denominadas sabugueiro e sabugueirodo- brasil, respectivamente, são utilizadas popularmente sob forma de infusão, como antiinflamatórias, laxativas e para condições febris resultantes de afecções do trato respiratório. Estudos prévios para S. nigra indicam compostos fenólicos como principais constituintes químicos, sendo estes relacionados às principais atividades biológicas avaliadas. Objetivando comparar esta espécie com Sambucus australis, foram realizadas análises botânicas macro e microscópicas das flores, identificando as principais diferenças entre as espécies, tais como o número de lóculos no ovário e presença de idioblastos cristalíferos em algumas estruturas, e observando os possíveis contaminantes (pedicelos). Também foram determinados os parâmetros farmacopéicos: cinzas totais e perda por dessecação. Após a análise química, foi escolhido o flavonóide rutina como marcador das espécies, para realizar análises quantitativas nas 31 amostras adquiridas e / ou coletadas, utilizando método de CLAE previamente validado. Soluções hidroetanólicas apresentaram maior capacidade de extração do produto alvo. Os limites mínimos de rutina observados para ambas as espécies foram de aproximadamente 0,65%. Também foram quantificados, por método espectrofotométrico, os flavonóides totais expressos em quercetina, sendo 0,93% e 1,46% os teores mínimos determinados para S.nigra e S. australis, respectivamente. O estudo da estabilidade acelerada (50°C ± 90% U.R.), avaliando a degradação dos constituintes químicos presentes permitiu sugerir a cinética de degradação de segunda ordem para da rutina nas duas espécies. Comparações de atividades biológicas das espécies foram realizadas pelos ensaios das atividades antiinflamatória (inibição do edema em pata de rato induzido por carragenina) e antioxidante (DPPH). Os resultados para o primeiro ensaio demonstraram ação equivalente em ambas as espécies para extratos hidroetanólicos a 80% (86% de inibição) e aquosos (81%), com atividade semelhante ao padrão indometacina (~83%); para a atividade antioxidante os extratos hidroetanólicos a 80% foram mais ativos (CE50 = 16 μg/ml) que os aquosos (CE50 = 27 μg/ml) em S. australis, e ambos extratos, superiores ao 28 extrato padronizado Gingko biloba (CE50 = 40 μg/ml) e aos extratos de S. nigra (CE50= 50 μg/ml – hidroetanólico e CE50= 32 μg/ml – aquoso).

Preparação e caracterização de sistemas emulsionados lipidicos contendo praziquantel

Praziquantel (PRZ) is the main drug used for treatment of schistosomiasis in Brazil. It is administered by oral rout as tablets. However, has low aqueous solubility which limits this therapeutic success dosage form and availability of liquid forms. The emulsion systems have great potential and represent an interesting strategy to increase the solubility of drugs. The aim of study was the development and characterization of lipid-emulsified liquid systems of the type oil in water (O / W), the base of soybean oil as the internal phase stabilized by surfactants pair Tween® 80 and Span® 80, for improving the phase biopharmaceutical of PRZ. After selecting the best value of Hydrophilic-Lipophilic Balance (HLB = 11), the parameters of the preparation of the formulations were optimized emulsification technique. The emulsions were successfully obtained; the liquid forms provided exhibited Newtonian behavior and an increase in solubility of PRZ higher than 20 times. The accelerated stability study demonstrated the stability of the emulsions and the effect of cosurfactants investigated. The study of the dynamics of interaction between components in the diagram showed pseudoternary phase regions to obtain O/W emulsions, whereas the study of the interaction of the components and their effect on system structure and the efficiency of incorporation of the drug led to systems with an amount of soluble drug even higher (about 1.5%), which demonstrates the potential of this new input mainly for the treatment of schistosomiasis, which resulted in the filing of patent BR 10 2013 0004 55 3

Dispersões sólidas de sinvastatina: preparação, caracterização, no estado sólido utilizando técnicas emergentes e estudo de estabilidade

This thesis aimed to assess the increase in solubility of simvastatin (SINV) with solid dispersions using techniques such as kneading (MA), co-solvent evaporation (ES), melting carrier (FC) and spray dryer (SD). Soluplus (SOL), PEG 6000 (PEG), PVP K-30 (PVP) e sodium lauryl sulphate (LSS) were used as carriers. The solid dispersions containing PEG [PEG-2(SD)], Soluplus [SOL-2(MA)] and sodium lauryl sulphate [LSS-2(ES)] were presented with a greater increase in solubility (5.02, 5.60 and 5.43 times respectively); analyses by ANOVA between the three groups did not present significant difference (p<0.05). In the phase solubility study, the calculation of the Gibbs free energy (ΔG) revealed that the spontaneity of solubilisation of SINV occurred in the order SOL>PEG >PVP 75%>LSS, always 80%. The phase diagrams of PEG and LSS presented solubilization stoichiometry of type 1:1 (type AL). The diagrams with PVP and SOL tend to 1:2 stoichiometry (type AL + AP). The stability coefficients (Ks) of the phase diagrams revealed that the most stable reactions occurred with LSS and PVP. The solid dispersions were characterized by Fourier transform infrared (FTIR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), particle size distribution (PSD), near-infrared spectroscopy imaging (NIR-CI) and X-ray diffraction of the powder using the Topas software (PDRX-TOPAS). The solid dispersion PEG-2(SD) presented the greatest homogeneity and the lowest degree of crystallinity (18.2%). The accelerated stability study revealed that the solid dispersions are less stable than SINV, with PEG-2(SD) being the least stable, confirmed by FTIR and DSC. The analyses by PDRX-TOPAS revealed the amorphous character of the dispersions and the mechanism of increasing solubility

Desenvolvimento de Modelos no Programa DigSILENT PowerFactoryTM para o Estudo de Estabilidade Transitória em Sistemas Elétricos de Potência com Aerogerador

This work presents a description of models development at DigSILENT PowerFactoryT M program for the transient stability study in power systems with wind turbine. The main goal is to make available means to use a dynamic simulation program in power systems, widely published, and utilize it as a tool that helps in programs results evaluations used for this intent. The process of simulations and analyses results starts after the models setting description phase. The results obtained by the DigSILENT PowerFactoryT M and ATP, program chosen to the validation also international recognized, are compared during this phase. The main tools and guide lines of PowerFactoryT M program use are presented here, directing these elements to the solution of the approached problem. For the simulation it is used a real system which it will be connected a wind farm. Two different technologies of wind turbines were implemented: doublyfed induction generator with frequency converter, connecting the rotor to the stator and to the grid, and synchronous wind generator with frequency converter, interconnecting the generator to the grid. Besides presenting the basic conceptions of dynamic simulation, it is described the implemented control strategies and models of turbine and converters. The stability of the wind turbine interconnected to grid is analyzed in many operational conditions, resultant of diverse kinds of disturbances