Stochastic gauges in quantum dynamics for many-body simulations

Quantum dynamics simulations can be improved using novel quasiprobability distributions based on non-orthogonal Hermitian kernel operators. This introduces arbitrary functions (gauges) into the stochastic equations. which can be used to tailor them for improved calculations. A possible application to full quantum dynamic simulations of BEC's is presented. (C) 2001 Elsevier Science B.V. All rights reserved.

Lanczos subspace time-independent wave packet calculations of S(D-1)+H-2 reactive scattering

In this paper. we present the results of quantum dynamical simulations of the S (D-1) + H-2 insertion reaction on a newly developed potential energy surface (J. Chem. Phys. 2001, 114, 320). State-to-state reaction probabilities. product state distributions, and initial-state resolved cumulative reaction probabilities from a given incoming reactant channel are obtained from a time-independent wave packet analysis, performed within a single Lanczos subspace. Integral reaction cross sections are then estimated by J-shifting method and compared with the results from molecular beam experiment and QCT calculations.

Application of the maximum entropy method to the (2 + 1)D four-fermion model

We investigate spectral functions extracted using the maximum entropy method from correlators measured in lattice simulations of the (2+1)-dimensional four-fermion model. This model is particularly interesting because it has both a chirally broken phase with a rich spectrum of mesonic bound states and a symmetric phase where there are only resonances. In the broken phase we study the elementary fermion, pion, sigma, and massive pseudoscalar meson; our results confirm the Goldstone nature of the π and permit an estimate of the meson binding energy. We have, however, seen no signal of σ→ππ decay as the chiral limit is approached. In the symmetric phase we observe a resonance of nonzero width in qualitative agreement with analytic expectations; in addition the ultraviolet behavior of the spectral functions is consistent with the large nonperturbative anomalous dimension for fermion composite operators expected in this model.

The folding of knotted proteins: insights from lattice simulations

We carry out systematic Monte Carlo simulations of Go lattice proteins to investigate and compare the folding processes of two model proteins whose native structures differ from each other due to the presence of a trefoil knot located near the terminus of one of the protein chains. We show that the folding time of the knotted fold is larger than that of the unknotted protein and that this difference in folding time is particularly striking in the temperature region below the optimal folding temperature. Both proteins display similar folding transition temperatures, which is indicative of similar thermal stabilities. By using the folding probability reaction coordinate as an estimator of folding progression we have found out that the formation of the knot is mainly a late folding event in our shallow knot system.

Monte Carlo modeling and simulations of the High Definition (HD120) micro MLC and validation against measurements for a 6 MV beam

Purpose: The most recent Varian® micro multileaf collimator(MLC), the High Definition (HD120) MLC, was modeled using the BEAMNRCMonte Carlo code. This model was incorporated into a Varian medical linear accelerator, for a 6 MV beam, in static and dynamic mode. The model was validated by comparing simulated profiles with measurements. Methods: The Varian® Trilogy® (2300C/D) accelerator model was accurately implemented using the state-of-the-art Monte Carlo simulation program BEAMNRC and validated against off-axis and depth dose profiles measured using ionization chambers, by adjusting the energy and the full width at half maximum (FWHM) of the initial electron beam. The HD120 MLC was modeled by developing a new BEAMNRC component module (CM), designated HDMLC, adapting the available DYNVMLC CM and incorporating the specific characteristics of this new micro MLC. The leaf dimensions were provided by the manufacturer. The geometry was visualized by tracing particles through the CM and recording their position when a leaf boundary is crossed. The leaf material density and abutting air gap between leaves were adjusted in order to obtain a good agreement between the simulated leakage profiles and EBT2 film measurements performed in a solid water phantom. To validate the HDMLC implementation, additional MLC static patterns were also simulated and compared to additional measurements. Furthermore, the ability to simulate dynamic MLC fields was implemented in the HDMLC CM. The simulation results of these fields were compared with EBT2 film measurements performed in a solid water phantom. Results: Overall, the discrepancies, with and without MLC, between the opened field simulations and the measurements using ionization chambers in a water phantom, for the off-axis profiles are below 2% and in depth-dose profiles are below 2% after the maximum dose depth and below 4% in the build-up region. On the conditions of these simulations, this tungsten-based MLC has a density of 18.7 g cm− 3 and an overall leakage of about 1.1 ± 0.03%. The discrepancies between the film measured and simulated closed and blocked fields are below 2% and 8%, respectively. Other measurements were performed for alternated leaf patterns and the agreement is satisfactory (to within 4%). The dynamic mode for this MLC was implemented and the discrepancies between film measurements and simulations are within 4%. Conclusions: The Varian® Trilogy® (2300 C/D) linear accelerator including the HD120 MLC was successfully modeled and simulated using the Monte CarloBEAMNRC code by developing an independent CM, the HDMLC CM, either in static and dynamic modes.

Monte Carlo simulations for dosimetric verification in photon and electron beam radiotherapy

Dissertação para obtenção do Grau de Doutor em Engenharia Biomédica

Lithium ion rechargeable batteries: State of the art and future needs of microscopic theoretical models and simulations

This review deals with the recent developments and present status of the theoretical models for the simulation of the performance of lithium ion batteries. Preceded by a description of the main materials used for each of the components of a battery -anode, cathode and separator- and how material characteristics affect battery performance, a description of the main theoretical models describing the operation and performance of a battery are presented. The influence of the most relevant parameters of the models, such as boundary conditions, geometry and material characteristics are discussed. Finally, suggestions for future work are proposed.

Simulations of parasitic and intrinsic capacitances related to Multiple-Gate-Field-Effect Transistor architectures

Report for the scientific sojourn carried out at the Université Catholique de Louvain, Belgium, from March until June 2007. In the first part, the impact of important geometrical parameters such as source and drain thickness, fin spacing, spacer width, etc. on the parasitic fringing capacitance component of multiple-gate field-effect transistors (MuGFET) is deeply analyzed using finite element simulations. Several architectures such as single gate, FinFETs (double gate), triple-gate represented by Pi-gate MOSFETs are simulated and compared in terms of channel and fringing capacitances for the same occupied die area. Simulations highlight the great impact of diminishing the spacing between fins for MuGFETs and the trade-off between the reduction of parasitic source and drain resistances and the increase of fringing capacitances when Selective Epitaxial Growth (SEG) technology is introduced. The impact of these technological solutions on the transistor cut-off frequencies is also discussed. The second part deals with the study of the effect of the volume inversion (VI) on the capacitances of undoped Double-Gate (DG) MOSFETs. For that purpose, we present simulation results for the capacitances of undoped DG MOSFETs using an explicit and analytical compact model. It monstrates that the transition from volume inversion regime to dual gate behaviour is well simulated. The model shows an accurate dependence on the silicon layer thickness,consistent withtwo dimensional numerical simulations, for both thin and thick silicon films. Whereas the current drive and transconductance are enhanced in volume inversion regime, our results show thatintrinsic capacitances present higher values as well, which may limit the high speed (delay time) behaviour of DG MOSFETs under volume inversion regime.

Models de simulació per coordinar serveis d'emergència

El projecte exposat té com a propòsit definir i implementar un model de simulació basat en la coordinació i assignació dels serveis d’emergència en accidents de trànsit. La definició del model s’ha realitzat amb l’ús de les Xarxes de Petri Acolorides i la implementació amb el software Rockwell Arena 7.0. El modelatge de la primera simulació ens mostra un model teòric basat en cues mentre que el segon, mostra un model més complet i real gràcies a la connexió mitjançant la plataforma Corba a una base de dades amb informació geogràfica de les flotes i de les rutes. Com a resultat de l’estudi i amb l’ajuda de GoogleEarth, podem realitzar simulacions gràfiques per veure els accidents generats, les flotes dels serveis i el moviment dels vehicles des de les bases fins als accidents.

Disseny i caracterització d'estructures RF amb printed electronics per a RFID

En els últims anys printed electronics està aixecant un gran interès entre la indústria electrònica. Aquest tipus de procés consisteix en imprimir circuits amb tècniques d'impressió convencionals utilitzant tintes conductores, resistives, dielèctriques o semiconductores sobre substrats flexibles de baix cost com paper o plàstic. Fer servir aquestes tècniques s'espera que suposi una reducció dels costos de producció degut a que és un procés totalment additiu el que fa que sigui més senzill i es redueixi la quantitat de material emprat. El disseny de dispositius bàsics com resistències, condensadors i bobines per posteriorment veure la relació entre simulacions i valors obtinguts ha ocupat la primera part del projecte. La segona s’ha centrat en fer prototips d’antenes per a RFID (Radio Frequency IDentification) amb la tecnologia que es disposa a CEPHIS (Centre de Prototips i Solucions Hardwre-Software). Tot això ha servit per caracteritzar la tecnologia de la que es disposa i saber en quins apartats s’ha de seguir treballant per aconseguir millors prestacions.

Sistemes lidar (radar laser) d'ona contínua i baixa potència per a la detecció i mesura de concentració de gasos amb resolució espacial

The present project has performed the study and development of a new technique for the detection of gases with range resolution. This technique called FMCW-lidar is a technique that evolves from the FMCW-radar technique to be applied to lidar systems. Moreover, it takes advantage of the appearance of spectral absorption lines because of the interaction between light and gases to tune the light wavelength of a laser emitter with one of this spectral lines and then detects the backscattered light and analyzes it in order to obtain gas concentration measurements. The first part of the project consisted in the analysis of the WMS technique which is a technique for the in-situ measurement of gases. A complete theoretical analysis has been performed and some experiments have been carried out in order to test the technique and to validate its application to an FMCW-modulated system for the detection of gases. The second part of the project consisted in the analysis of the lidar FMCW technique for solid target detection and its extension to continuous media. The classical form of this technique has been analyzed for a distributed medium and a filtering effect has been found which prevents the accurate acquisition of the medium response. A modification of the technique has been proposed and a validation via simulations and some experiments has been carried on. After performing these tests, a novel system is proposed to be developed and tested in order to perform the indicated gas detection with range resolution.

Consolidació de la Plataforma COMalaWEB com a eina Web d'autoaprenentatge per a l'EEES

La plataforma d’e-learning: COMalaWEB és una eina multimedia de suport a l’estudi, l’experimentació i l’adquisició de tècniques d’autoaprenentatge. COMalaWEB s’ofereix com a punt de trobada entre estudiants, professors i altres professionals relacionats amb el mon de les telecomunicacions i/o de la docència universitària. Mitjançant el present projecte s’ha dut a terme la consolidació de la plataforma COMalaWEB com a eina WWW d'autoaprenentatge per a l'EEES (Estudis de Bachelor i de Màster): Dins de la plataforma s’hi ha integrat un Laboratori Virtual per a comunicacions analògiques i digitals (LaViCAD) que ofereix activitats experimentals amb un gran ventall de possibilitats que van des de les demostracions teòriques fins a l’emulació de sistemes de comunicacions quotidians com per exemple la televisió digital o el sistema Wifi dels sistemes WLAN. L’altre gran component de la plataforma es la base de dades de continguts empaquetada en unitats bàsiques anomenades objectes de coneixement, organitzada en cursos, integren tant continguts teòrics com un conjunt d’exercicis proposats per a aprofundir cadascun dels temes tractats. Amb l’actual projecte s’ha treballat en les següents línies d’actuació: - Integració dels simuladors del laboratori LAVICAD a la plataforma d’autoaprenentatge. - Creació de base de dades de recursos docents basats en paquets SCORM per a oferir materials docents de tipus teòric i col·leccions d’exercicis resolts en el marc de les diferents assignatures participants en el projecte. - Creació de base de dades de tipus qüestionari per a oferir exercicis a treballar en el marc de les diferents assignatures participants en el projecte. - Inserció de metodologies docents basades en els anteriors recursos en diferents assignatures d’estudis d’enginyeria i de màster.

L'aprenentatge basat en problemes (PBL) en la regulació del metabolisme. Desenvolupament del portal per a l'intercanvi d'experiències en PBL en ciències biomèdiques

L’aprenentatge basat en problemes està en fase experimental en tot el món i és objecte d’anàlisi i reflexió en moltes reunions internacionals. Tanmateix, no hi ha massa feina feta en aquesta direcció en el nostre camp més proper. Hem elaborat problemes per l’aprenentatge de la Regulació del Metabolisme i els hem incorporat a un porta virtual (http://www.ub.edu/GID-BBM). La finalitat d’aquesta estratègia és que mitjançant l’aprenentatge basat en problemes reals o simulacions de problemes reals s’aconsegueixi motivar l’alumnat a treballar de forma continuada durant tot el curs. La millora dels resultats acadèmics haurà de ser la conseqüència lògica d’aquest treball. La finalitat última del projecte que hem desenvolupat és preparar l’alumnat per la seva futura activitat professional a on serà molt important i valorat la seva capacitat de resposta davant de diferents problemes

Estudi de comportaments socials d'aixams robòtics amb aplicació a la neteja d'espais no estructurats

La intel·ligència d’eixams és una branca de la intel·ligència artificial que està agafant molta força en els últims temps, especialment en el camp de la robòtica. En aquest projecte estudiarem el comportament social sorgit de les interaccions entre un nombre determinat de robots autònoms en el camp de la neteja de grans superfícies. Un cop triat un escenari i un robot que s’ajustin als requeriments del projecte, realitzarem una sèrie de simulacions a partir de diferents polítiques de cerca que ens permetran avaluar el comportament dels robots per unes condicions inicials de distribució dels robots i zones a netejar. A partir dels resultats obtinguts serem capaços de determinar quina configuració genera millors resultats.