An improved representation of vehicle incompatibility in frontal NCAP tests using a modified rigid barrier

With the objective of better understanding the significance of New Car Assessment Program (NCAP) tests conducted by the National Highway Traffic Safety Administration (NHTSA), head-on collisions between two identical cars of different sizes and between cars and a pickup truck are studied in the present paper using LS-DYNA models. Available finite element models of a compact car (Dodge Neon), midsize car (Dodge Intrepid), and pickup truck (Chevrolet C1500) are first improved and validated by comparing theanalysis-based vehicle deceleration pulses against corresponding NCAP crash test histories reported by NHTSA. In confirmation of prevalent perception, simulation-bascd results indicate that an NCAP test against a rigid barrier is a good representation of a collision between two similar cars approaching each other at a speed of 56.3 kmph (35 mph) both in terms of peak deceleration and intrusions. However, analyses carried out for collisions between two incompatible vehicles, such as an Intrepid or Neon against a C1500, point to the inability of the NCAP tests in representing the substantially higher intrusions in the front upper regions experienced by the cars, although peak decelerations in cars arc comparable to those observed in NCAP tests. In an attempt to improve the capability of a front NCAP test to better represent real-world crashes between incompatible vehicles, i.e., ones with contrasting ride height and lower body stiffness, two modified rigid barriers are studied. One of these barriers, which is of stepped geometry with a curved front face, leads to significantly improved correlation of intrusions in the upper regions of cars with respect to those yielded in the simulation of collisions between incompatible vehicles, together with the yielding of similar vehicle peak decelerations obtained in NCAP tests.

Performance of polymeric reinforcements in vehicle structures submitted to frontal impact

Preformed structural reinforcements have shown good performance in crash tests, where the great advantage is their weight. These reinforcements are designed with the aim of increasing the rigidity of regions with large deformations, thus stabilising sections of the vehicle that work as load path during impact. The objective of this work is to show the application of structural reinforcements made of polymeric material PA66 in the field of vehicle safety, through finite element simulations. Simulations of frontal impact at 50 km/h and in ODB (offset deformable barrier) at 57 km/h configurations (standards such as ECE R-94 and ECE R-12) were performed in the software LS-DYNA R (R) and MADYMO (R). The simulations showed that the use of polymeric reinforcements leads to a 70% reduction in A-pillar intrusion, a 65% reduction in the displacement of the steering column and a 59% reduction in the deformation in the region of the occupant legs and feet. The level of occupant injuries was analysed by MADYMO (R) software, and a reduction of 23.5% in the chest compression and 80% in the tibia compression were verified. According to the standard, such conditions lead to an improvement in the occupant safety in a vehicle collision event.

Final report of 270 degree contoured moving barrier impact into a 1985 Chrysler LeBaron 5-door hatchback in support of CRASH III damage algorithm reformation.

Mode of access: Internet.

Final report of 270 degree contoured moving barrier impact into a 1985 Chevrolet Celebrity 4-door sedan in support of CRASH III damage algorithm reformation.

Mode of access: Internet.

Final report of 270 degree contoured moving barrier impact into a 1983 Honda Prelude 2-door coupe in support of CRASH III damage algorithm reformation.

Mode of access: Internet.

Final report of 270 degree contoured moving barrier impact into a 1985 Nissan Sentra 2-door coupe in support of CRASH III damage algorithm reformation.

Mode of access: Internet.

Final report of 270 degree contoured moving barrier impact into a 1983 Ford Tempo 4-door sedan in support of CRASH III damage algorithm reformation. Final report.

Mode of access: Internet.

Crash III model improvements: MRB-to-car side impact of a 90 [degree] moving rigid barrier to a 1983 Mitsubishi Tredia: test #1 - 16.7 mph, test #2 - 33.5 mph. Test report.

Mode of access: Internet.

An energy-absorbing frangible-tube bridge barrier system. Final report.

Mode of access: Internet.

CRASH III model improvements: MRB-to-car side impact test of a 90 [degree] moving rigid barrier to a 1981 Chevrolet Citation test speed 35.2 mph.

Mode of access: Internet.

Testing and simulation of extruded polystyrene foam at low to moderate strain rates

This paper presents a study into the behaviour of extruded polystyrene foam at low strain rates. The foam is being studied in order assess its potential for use as part of a new innovative design of portable road safety barrier the aim to consume less water and reduce rates of serious injury. The foam was tested at a range of low strain rates, with the stress and strain behaviour of the foam specimens being recorded. The energy absorption capabilities of the foam were assessed as well as the response of the foam to multiple loadings. The experimental data was then used to create a material model of the foam for use in the explicit finite element solver LS-DYNA. Simulations were carried out using the material model which showed excellent correlation between the numerical material model and the experimental data.

A simultaneous equations model of crash frequency by collision type for rural intersections

Safety at roadway intersections is of significant interest to transportation professionals due to the large number of intersections in transportation networks, the complexity of traffic movements at these locations that leads to large numbers of conflicts, and the wide variety of geometric and operational features that define them. A variety of collision types including head-on, sideswipe, rear-end, and angle crashes occur at intersections. While intersection crash totals may not reveal a site deficiency, over exposure of a specific crash type may reveal otherwise undetected deficiencies. Thus, there is a need to be able to model the expected frequency of crashes by collision type at intersections to enable the detection of problems and the implementation of effective design strategies and countermeasures. Statistically, it is important to consider modeling collision type frequencies simultaneously to account for the possibility of common unobserved factors affecting crash frequencies across crash types. In this paper, a simultaneous equations model of crash frequencies by collision type is developed and presented using crash data for rural intersections in Georgia. The model estimation results support the notion of the presence of significant common unobserved factors across crash types, although the impact of these factors on parameter estimates is found to be rather modest.

Development of a test methodology for evaluating crash compatibility and aggressiveness. Test report 1: 1975 Honda Civic CVCC-to-NHTSA test device.

National Highway Traffic Safety Administration, Washington, D.C.

Development of a test methodology for evaluating crash compatibility and aggressiveness. Test report 2: 1975 Ford Torino-to-NHTSA test device.

National Highway Traffic Safety Administration, Washington, D.C.

Moving deformable barrier into left side of 1995 Solectria Force at 52.9 kph. Final report.

National Highway Traffic Safety Administration, Washington, D.C.