Mapeamento geológico-geotécnico pelo método de detalhamento progressivo: aplicação no planejamento e gestão de obras rodoviárias

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Solid electrolytes for electrochromic devices based on reversible metal electrodeposition

Air conditioning and lighting costs can be reduced substantially by changing the optical properties of "intelligent windows." The electrochromic devices studied to date have used copper as an additive. Copper, used here as an electrochromic material, was dissolved in an aqueous animal protein-derived gel electrolyte. This combination constitutes the electrochromic system for reversible electrodeposition. Cyclic voltammetry, chronoamperometric and chromogenic analyses indicated that were obtained good conditions of transparency (initial transmittance of 70%), optical reversibility, small potential window (2.1 V), variation of transmittance in visible light (63.6%) and near infrared (20%) spectral regions. Permanence in the darkened state was achieved by maintaining a lower pulse potential (-0.16 V) than the deposition potential (-1.0 V). Increasing the number of deposition and dissolution cycles favored the transmittance and photoelectrochemical reversibility of the device. The conductivity of the electrolyte (10(-3) S/cm) at several concentrations of CuCl2 was determined by electrochemical impedance spectroscopy. A thermogravimetric analysis confirmed the good thermal stability of the electrolyte, since the mass loss detected up to 100 degrees C corresponded to water evaporation and decomposition of the gel started only at 200 degrees C. Micrographic and small angle X-ray scattering analyses indicated the formation of a persistent deposit of copper particles on the ITO. (C) 2012 Elsevier B.V. All rights reserved.

Alternative incandescent traffic signal lamps and systems for improved optical and energy efficiency. Final report.

Federal Highway Administration, Office of Safety and Traffic Operations Research and Development, Washington, D.C.

Statewide pedestrian study. Phase III report: correlation and evaluation of pedestrian accident data. Final report.

Mode of access: Internet.

Evaluation of the ADDCO flip-disc variable message sign.

Federal Highway Administration, Washington, D.C.

Accident cause analysis. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Estimating health related costs and savings from balcony acoustic design for road traffic noise

A multi-faceted study is conducted with the objective of estimating the potential fiscal savings in annoyance and sleep disturbance related health costs due to providing improved building acoustic design standards. This study uses balcony acoustic treatments in response to road traffic noise as an example. The study area is the State of Queensland in Australia, where regional road traffic noise mapping data is used in conjunction with standard dose–response curves to estimate the population exposure levels. The background and the importance of using the selected road traffic noise indicators are discussed. In order to achieve the objective, correlations between the mapping indicator (LA10 (18 hour)) and the dose response curve indicators (Lden and Lnight) are established via analysis on a large database of road traffic noise measurement data. The existing noise exposure of the study area is used to estimate the fiscal reductions in health related costs through the application of simple estimations of costs per person per year per degree of annoyance or sleep disturbance. The results demonstrate that balcony acoustic treatments may provide a significant benefit towards reducing the health related costs of road traffic noise in a community.

Final : report assessing risk and variation in maintenance and rehabilitation costs for road network

This report presents the results of research projects conducted by The Australian Cooperative Research Centre for Construction Innovation, Queensland University of Technology, RMIT University, Queensland Government Department of Main Roads and Queensland Department of Public Works. The research projects aimed at developing a methodology for assessing variation and risk in investment in road network, including the application of the method in assessing road network performance and maintenance and rehabilitation costs for short- and long-term future investment.

Improved Road Design for Future Maintenance - Analysis of Road Barrier Repair Costs

The cost of a road construction over its service life is a function of the design, quality of construction, maintenance strategies and maintenance operations. Unfortunately, designers often neglect a very important aspect which is the possibility to perform future maintenance activities. The focus is mainly on other aspects such as investment costs, traffic safety, aesthetic appearance, regional development and environmental effects. This licentiate thesis is a part of a Ph.D. project entitled “Road Design for lower maintenance costs��� that aims to examine how the life-cycle costs can be optimized by selection of appropriate geometrical designs for the roads and their components. The result is expected to give a basis for a new method used in the road planning and design process using life-cycle cost analysis with particular emphasis on road maintenance. The project started with a review of literature with the intention to study conditions causing increased needs for road maintenance, the efforts made by the road authorities to satisfy those needs and the improvement potential by consideration of maintenance aspects during planning and design. An investigation was carried out to identify the problems which obstruct due consideration of maintenance aspects during the road planning and design process. This investigation focused mainly on the road planning and design process at the Swedish Road Administration. However, the road planning and design process in Denmark, Finland and Norway were also roughly evaluated to gain a broader knowledge about the research subject. The investigation was carried out in two phases: data collection and data analysis. Data was collected by semi-structured interviews with expert actors involved in planning, design and maintenance and by a review of design-related documents. Data analyses were carried out using a method called “Change Analysis”. This investigation revealed a complex combination of problems which result in inadequate consideration of maintenance aspects. Several urgent needs for changes to eliminate these problems were identified. Another study was carried out to develop a model for calculation of the repair costs for damages of different road barrier types and to analyse how factors such as road type, speed limits, barrier types, barrier placement, type of road section, alignment and seasonal effects affect the barrier damages and the associated repair costs. This study was carried out using a method called the “Case Study Research Method”. Data was collected from 1087 barrier repairs in two regional offices of the Swedish Road Administration, the Central Region and the Western Region. A table was established for both regions containing the repair cost per vehicle kilometre for different combinations of barrier types, road types and speed limits. This table can be used by the designers in the calculation of the life-cycle costs for different road barrier types.

Costs to the public due to the use of corrosive deicing chemicals and a comparison to alternate winter road maintenance procedures.

Alaska Department of Transportation and Public Facilities, Fairbanks

Allocation of road and street costs.

pt. 1. An equitable solution to the problem. Sect. 1-5 by R. G. Hennes [et al.]--pt. 2. Classification, traffic volumes and annual costs of county roads and city streets in the state of Washington, by G. A. Riedesel.--pt. 3. Bases for weight-distance taxation in the state of Washington. v. 1. Automobiles & taxicabs. v. 2. Trucks & buses.--pt. 4. The benefits of rural roads to rural property, by Wm. L. Garrison.--pt. 5. The effect of freeway access uponsuburban real property values, by R. O. Wheeler.

The economic costs of road traffic crashes: Australia, states and territories

In this paper, we obtain detailed data on road traffic crash (RTC) casualties, by severity, for each of the eight state and territory jurisdictions for Australia and use these to estimate and compare the economic impact of RTCs across these regions. We show that the annual cost of RTCs in Australia, in 2003, was approximately $17b, which is approximately 2.3% of the Gross Domestic Product (GDP). Importantly, though, there is remarkable intra-national variation in the incident rates of RTCs in Australia and costs range from approximately 0.62 to 3.63% of Gross State Product (GSP). The paper makes two fundamental contributions: (i) it provides a detailed breakdown of estimated RTC casualties, by state and territory regions in Australia, and (ii) it presents the first sub-national breakdown of RTC costs for Australia. We trust that these contributions will assist policy-makers to understand sub-national variations in the road toll better and will encourage further research on the causes of the marked differences between RTC outcomes across the states and territories of Australia. (c) 2006 Elsevier Ltd. All rights reserved.