柴油、甲醇和水三组元乳化液流变特性的研究

对柴油、甲醇和水三组元乳化液的流变特性进行了研究。实验发现，乳化液在本实验的组分配比下近似为牛顿流体，而且乳化剂的种类、含量以及乳化液的组分均对乳化液的流变特性具有显著的影响。对于组分相同的乳化液，乳化液的粘度随着乳化剂含量和粘度的增加而增加；当乳化剂的含量和粘度相同时，若甲醇和水之间的相对质量分数保持不变，减少乳化液中柴油的质量分数（不少于50%），乳化液的粘度随之增加。水和甲醇的含量对乳化液粘度的影响比较复杂，还需要做深入细致的机理研究。

柴油、乙醇和水三组元乳化液流变特性的研究

研究了柴油、乙醇和水三组元乳化液的流变特性.实验发现乳化液在本文的组分配比下近似为牛顿流体,而且乳化剂的种类、含量以及乳化液的组分等均对乳化液的流变特性具有显著的影响.对于组分相同的乳化液,乳化液的粘度随着乳化剂含量和粘度的增加而增加;当乳化剂的含量和粘度相同时,若乙醇和水之间的相对质量分数保持不变,减少乳化液中柴油的含量(柴油不少于50%),乳化液的粘度随之增加.但是,柴油、乙醇和水三组元乳化液的粘度要比柴油、甲醇和水三组元乳化液的粘度大2到3倍.

柴油与水乳化液的流变特性

采用自行配置的复合型乳化剂，通过超声波方法制得了柴油和水乳化液，并进行了相应乳化液的黏度特性实验．乳化液在给定组分配比下近似为牛顿流体，乳化剂种类、质量分数以及乳化液组分等均对乳化液的流变特性具有显著的影响．组分相同的乳化液，黏度随着乳化剂质量分数和黏度的增加而增加；当乳化剂质量分数和黏度相同时，乳化液的黏度随着乳化液中柴油质量分数（柴油不少于50％）的减少而增加．

Improved Melting Strength of Polypropylene by Reactive Compounding With Ultrafine Full-Vulcanized Polybutadiene Rubber (UFBR) Particles

Ultrafine full-vulcanized polybutadiene rubber (UFBR) in particle sizes of ca. 50-100 nm has been used for modifying mechanical and processing performances of polypropylene (PP), and PP-g-maleic anhydride (PP-MA) has been used as a compatibilizer for enhancing the interfacial adhesion between the two components. The results show that PP/UFBR possesses rheological behaviors such as highly branched PP when UFBR content in blends reaches 10 wt%, while in contrast, the much low content of UFBR combining small amount of PP-MA endows the material with rheological characteristics of high melt strength materials like highly branched PP.

青藏高原东部电性结构特征及地球动力学意义

As the largest and highest plateau on the Earth, the Tibetan Plateau has been a key location for understanding the processes of mountain building and plateau formation during India-Asia continent-continent collision. As the front-end of the collision, the geological structure of eastern Tibetan Plateau is very complex. It is ideal as a natural laboratory for investigating the formation and evolution of the Tibetan Plateau. Institute of Geophysics, Chinese Academy of Sciences (CAS) carried out MT survey from XiaZayii to Qingshuihe in the east part of the plateau in 1998. After error analysis and distortion analysis, the Non-linear Conjugate Gradient inversion(NLCG), Rapid Relaxation Inversin (RRI) and 2D OCCAM Inversion algorithms were used to invert the data. The three models obtained from 3 algorithms provided similar electrical structure and the NLCG model fit the observed data better than the other two models. According to the analysis of skin depth, the exploration depth of MT in Tibet is much more shallow than in stable continent. For example, the Schmucker depth at period 100s is less than 50km in Tibet, but more than 100km in Canadian Shield. There is a high conductivity layer at the depth of several kilometers beneath middle Qiangtang terrane, and almost 30 kilometers beneath northern Qiangtang terrane. The sensitivity analysis of the data predicates that the depth and resistivity of the crustal high conductivity layer are reliable. The MT results provide a high conductivity layer at 20~40km depth, where the seismic data show a low velocity zone. The experiments show that the rock will dehydrate and partially melt in the relative temperature and pressure. Fluids originated from dehydration and partial melting will seriously change rheological characteristics of rock. Therefore, This layer with low velocity and high conductivity layer in the crust is a weak layer. There is a low velocity path at the depth of 90-110 km beneath southeastern Tibetan Plateau and adjacent areas from seismology results. The analysis on the temperature and rheological property of the lithosphere show that the low velocity path is also weak. GPS measurements and the numerical simulation of the crust-mantle deformation show that the movement rate is different for different terranes. The regional strike derived from decomposition analysis for different frequency band and seismic anisotropy indicate that the crust and upper mantle move separately instead of as a whole. There are material flow in the eastern and southeastern Tibetan Plateau. Therefore, the faults, the crustal and upper mantle weak layers are three different boundaries for relatively movement. Those results support the "two layer wedge plates" geodynamic model on Tibetan formation and evolution.

Influence of mix proprtions on rheolgy of cement grouts containing limestone powder

In this paper the parameters of cement grout affecting rheological behaviour and compressive strength are investigated. Factorial experimental design was adopted in this investigation to assess the combined effects of the following factors on fluidity, rheological properties, induced bleeding and compressive strength: water/binder ratio (W/B), dosage of superplasticiser (SP), dosage of viscosity agent (VA), and proportion of limestone powder as replacement of cement (LSP). Mini-slump test, Marsh cone, Lombardi plate cohesion meter, induced bleeding test, coaxial rotating cylinder viscometer were used to evaluate the rheology of the cement grout and the compressive strengths at 7 and 28 days were measured. A two-level fractional factorial statistical model was used to model the influence of key parameters on properties affecting the fluidity, the rheology and compressive strength. The models are valid for mixes with 0.35-0.42 W/B, 0.3-1.2% SP, 0.02-0.7% VA (percentage of binder) and 12-45% LSP as replacement of cement. The influences of W/B, SP, VA and LSP were characterised and analysed using polynomial regression which can identify the primary factors and their interactions on the measured properties. Mathematical polynomials were developed for mini-slump, plate cohesion meter, inducing bleeding, yield value, plastic viscosity and compressive strength as function of W/B, SP, VA and proportion of LSP. The statistical approach used highlighted the limestone powder effect and the dosage of SP and VA on the various rheological characteristics of cement grout

Comparison of tack of pressure-sensitive adhesives (PSAs) at different temperatures

Pressure-sensitive adhesives (PSAs) have applications in the fields of packaging, joining, wound care, and personal care. Depending on the application of the PSA, different performance tests are carried out when new products are developed or the quality of the existing products is checked. Tack is the property of an adhesive that enables it to form instant bond on the surface under light pressure. The tack of a PSA strongly depends on the way the bond is created. Parameters such as the bonded area, contact time and the nature of tack materials all affect the tack force measured. In the development of any PSA, it is desirable to correlate the performance related properties such as tack and peel strength to the rheological behaviour. Finding these correlations would make it possible to evaluate the performance of a PSA using its rheological characteristics. In this investigation we have studied the influence of rheological behaviour of three different PSAs on their tackiness. The three different PSAs used in this study are a low molecular weight rosin ester, high molecular weight rosin ester, and dicyclopentadiene. Various rheological properties such as viscosity, phase angle, and elastic and viscous moduli are measured versus the frequency and temperature. Also the tack properties at various removal speeds and temperatures are evaluated. Analysis of the results indicates different performances of the three PSAs which could be related to their rheological properties, especially the phase angle, at different frequencies and temperatures. The PSA with high molecular weight rosin ester is more sensitive to temperature changes and showed drastic changes in tackiness from high temperature to low temperature. On the other hand, rosin ester with low molecular weight is less sensitive to temperature changes. © 2010 VSP.

Influence des caractéristiques rhéologiques des bétons autoplaçants sur leur durabilité

Résumé : De même degré d’importance que les paramètres de formulation, les conditions de consolidation sont des facteurs déterminants pour la durabilité des bétons conventionnels vibrés. Dans le cas des bétons autoplaçants (BAP), grâce à leur grande fluidité, la mise en place dans les coffrages a lieu par écoulement libre sous l’effet de leur poids propre. Leur consolidation se fait sans vibration grâce à leurs caractéristiques rhéologiques. Il est donc légitime de penser que les caractéristiques rhéologiques des BAP peuvent avoir une influence importante sur les propriétés qui déterminent la durabilité. Cette thèse étudie les liens possibles entre les caractéristiques rhéologiques des BAP et leur durabilité vis-à-vis du transport des agents agressifs. Dix-sept formulations de BAP couvrant une large gamme de caractéristiques rhéologiques et se différenciant uniquement par leur dosage en adjuvants ont été étudiées à cet effet. Trois modèles rhéologiques classiques ont été mis en œuvre pour la détermination des paramètres rhéologiques des bétons étudiés. L’essai de sorptivité et dans une moindre mesure l’essai de carbonatation accélérée ont été utilisés comme indicateur de durabilité vis-à-vis du transport des agressifs. La durabilité de la couche superficielle au contact respectivement avec le coffrage en bois et en PVC a été étudiée et les résultats ont été comparés à la durabilité du béton à cœur. Cette étude a été faite en tenant compte des échanges hydriques et de l’arrangement granulaire au droit du coffrage. D’autre part, l’étude de la durabilité de la couche superficielle dans des conditions de mise en place proches du chantier a été faite sur 6 poutres partiellement armées longues de 2 m ainsi que sur 3 bétons semi-autoplaçants légèrement vibrés. Les résultats montrent qu’il existe une corrélation forte entre la viscosité plastique du modèle Bingham modifié ou le coefficient de consistance du modèle Herschel-Bulkley et la sorptivité. Très probablement, la viscosité agit sur le volume relatif des pores capillaires de gros diamètres. L’étude spécifique de la couche superficielle a montré que sa sorptivité dépend du type de coffrage utilisé à cause des éventuels échanges hydriques opérés entre le béton et la surface du coffrage. De plus, l’arrangement granulaire au droit du coffrage est également influencé. Ainsi, la sorptivité de la couche superficielle au contact du PVC est proche mais inférieure à celle du béton à cœur. La sorptivité de la couche superficielle au contact du bois est significativement inférieure à celle de la couche superficielle au contact du PVC tout en restant corrélé avec la viscosité plastique du modèle Bingham modifié ou le coefficient de consistance du modèle Herschel-Bulkley.

Rheology of Short Nylon -6 Fiber Reinforced Styrene-Butadiene Rubber

The rheological characteristics of short Nylon-6 fiber reinforced styrene butadiene rubber (SBR) were studied using a capillary rheometer. The study was done with respect to the effect of shear rate, fiber concentration, and temperature on shear viscosity and die swell. All the melts showed pseudoplastic nature, which decreased with increasing temperature. Shear viscosity increased in the presence of fibers. Introduction of fiber reduces the temperature sensitivity of the rubber matrix. A reduction in die swell was found in presence of fibers.

Studies on short Nylon-6 fiber - elastomer composites with epoxy resin as bonding agent

The thesis describes the development and evaluation of epoxy resin as interfacial bonding agent for short Nylon-6 fiber elastomer composites. Epoxy resin is well known for its adhesive property. The potential use of it as interfacial bonding agent in short fiber composite is not explored yet. Three rubbers viz., acrylonitrile butadiene rubber (NBR), Neoprene rubber (CR) and styrene butadiene rubber (SBR) were selected and different fiber loading were tried. The resin concentration was optimized for each fiber loading with respect to cure characteristics and mechanical properties. Rheological characteristics and thermal degradation of the composites containing different fiber loading and different resin concentrations were studied in detail to find the effect of epoxy resin bonding system. The mechanical properties were studied in detail. The short Nylon -6 fiber improved most of the mechanical properties of all the three rubbers. Tensile strength showed a dip at 10 phr fiber loading in the case of CR while it was continuously increased with fiber loading in the case of NBR and SBR. All the composites showed anisotropy in mechanical properties. The epoxy resin is an effective bonding agent for short Nylon -6 fiber reinforced NBR and CR composites. Epoxy resin improved tensile strength, abrasion resistance and modulus of these composites. SEM studies confirmed the improved bonding of fiber and matrix in the presence of epoxy bonding agent. Epoxy resin was not effective as bonding agent in the case of short Nylon fiber- SBR composite. From the rheological studies of the composites with and without bonding agent it was observed that all the composite exhibited pseudoplasticity, which decreased with temperature. At higher shear rates all the mixes showed plug flow. SEM pictures showed that maximum orientation of fibers occured at a shear rate, just before the onset of plug flow. The presence of fiber reduced the temperature sensitivity of the flow at a given shear rate. Die swell was reduced in the presence of fiber. Shear viscosity of the composite was increased in the presence of resin. Die swell was increased in the presence of epoxy resin for composites at all shear rates. The thermal degradation of NBR and SBR composites with and without bonding agent followed single step degradation pattern. Thermal stability of the composites was improved in the presence of bonding agent. The degradation of virgin elastomer and the composites followed first order kinetics.

EPDM/CIIR Blends: Compatibility, Morphology and Physical Properties

A detailed study of the blends of ethylene-propylene-diene rubber (EPDM) and chlorobutyl rubber (CIIR) is proposed in this study. These blends may find application in the manufacture of curing diaphragms/curing envelopes for tire curing applications. EPDM possesses better physical properties such as high heat resistance, ozone resistance, cold and moisture resistance, high resistance to permanent defonnation, very good resistance to flex cracking and impact. Because of the low gas and moisture penneability, good weathering resistance and high thermal stability of CIIR, blends of EPDM with CIlR may be attractive, if sufficient mechanical strength can be developed. Although a lot of work has been done on elastomer blends, studies on the blends of EPDM and CIIR rubbers are meagre. Hence in this investigation it is proposed to make a systematic study on the characteristics of EPDM and CIIR rubber blends.The mechanical and physical properties of an elastomer blend depend mainly on the blend compatibility. So in the first part of the study, it is proposed to develop compatible blends of EPDM with CIIR. Various commercial grades of ethylenepropylene- diene rubber are proposed to be blended with a specific grade of chlorobutyl rubber at varying proportions. The extent of compatibility in these blends is proposed to be evaluated based on their mechanical properties such as tensile strength, tear strength and ageing resistance. In addition to the physical property measurements, blend compatibility is also proposed to be studied based on the glass transition behavlour of the blends in relation to the Tg's of the individual components using Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA). The phase morphology of the blends is also proposed to be investigated by Scanning Electron Microscopy (SEM) studies of the tensile fracture surfaces. In the case of incompatible blends, the effect of addition of chlorosulfonated polyethylene as a compatibiliser is also proposed to be investigated.In the second part of the study, the effect of sulphur curing and resin curing on the curing behaviour and the vulcanizate properties of EPDM/CIIR blends are planned to be evaluated. Since the properties of rubber vulcanizates are determined by their network structures, it is proposed to determine the network structure of the vulcanizates by chemical probes so as to correlate it with the mechanical properties.In the third part of the work, the effect of partial precuring of one of the components prior to blending as a possible means of improving the properties of the blend is proposed to be investigated. This procedure may also help to bring down the viscosity mismatch between the constituent e1astomers and provide covulcanization of the blend.The rheological characteristics and processability of the blends are proposed to be investigated in the last part of the study. To explore their possible applications, the air permeability of the blend samples at varying temperatures is proposed to be measured. The thermal diffusivity behaviour of EPDM/CIlR blends is also proposed to be investigated using novel laser technique. The thermal diffusivity of the blends along with the thermal degradation resistance may help to determine whether the blends are suitable for high temperature applications such as in the manufacturing of curing envelope.

Studies on LDPE/LLDPE Blends

Department of Polymer Science and Rubber Technology, Cochin University of Science and Technology

Avaluació del procés de desintegració de papers recuperats

La desintegració és una etapa important en la recuperació de paper vell, ja que té importants conseqüències en consum d'energia i en el comportament de les etapes posteriors. Per això els objectius es centren en analitzar la desintegració des del punt de vista del temps de desintegració, els aspectes energètics, modelització de la màquina de desintegració utilitzada i anàlisi dels factors de cisallament calculats com a mesura global de les forces implicades en la desintegració. Els autors que hi han treballat donen diferents explicacions a aquestes forces. Fins avui només s'ha pogut avaluar qualitativament la influència que tenen cada un dels mecanismes en el temps necessari per a desintegrar i en el consum energètic. Les característiques reològiques de les suspensions papereres, i el seu comportament no newtonià tenen una clara influència en el consum energètic i les forces de desfibrat en el desintegrador. Els experiments de desintegració s'han realitzat en un púlper convencional, amb tres tipus de paper recuperat: paper estucat d'alta qualitat imprès offset (PQ), paper revista estucat imprès en color (PR), paper blanc imprès en impresora làsser (PF). Anàlisi del temps de desintegració Per cada un del papers estudiats (PQ, PR i PF), les fraccions màssiques des de 0.06 fins a la màxima que estat possible per cada paper (de 0.14 a 0.18), i a dues velocitats d'agitació diferents, s'ha determinat el temps de desintegració (tD) fins a aconseguir un índex de Sommerville de 0.01%. S'obté que en augmentar la fracció màssica disminueix potencialment el temps de desintegració. S'ha estudiat la velocitat de desintegració, la producció teòrica del púlper en cada cas, i la seva relació amb les forces d'impacte i de fregament que produeixen la desintegració. Aspectes energètics El consum específic d'energia (SEC), definit com l'energia consumida per a desintegrar 1 kg de paper recuperat, disminueix molt en augmentar Xm, ja que a més de disminuir l'energia consumida en cada desintegració, el contingut en paper és més elevat. Pel disseny de desintegradors, cal tenir en compte que en augmentar Xm i en augmentar la velocitat, sempre augmenta la potència consumida. Però així com els beneficis de treballar a Xm alt són de 10 vegades en termes de SEC i de producció, l'augment de potència és només de l'ordre de 2 vegades la necessària respecte de la Xm baixa. Viscositat aparent i energia de fluidització S'estudia la relació entre el temps de desintegració, les forces de fregament i els valors de viscositat aparent de la bibliografia. Per cada paper i velocitat s'ha observat que el consum específic d'energia disminueix en funció de la viscositat aparent. Reologia del púlper Utilitzant el mètode de Metzner i Otto (1957) per determinar la viscositat aparent mitjana de les suspensions papereres, modificat per Roustan, s'ha caracteritzat el pulper mitjançant el model: Np= K· Rex·Fry S'han utilitzat dissolucions de glicerina com a fluid newtonià per a calcular les constants d'ajust, i a partir d'aquí, aïllar la viscositat aparent en funció de la potència neta i els paràmetres d'agitació. La viscositat aparent, d'acord amb Fabry (1999) es substitueix pel concepte de factor de cisallament. Factor de cisallament Calculat el factor de cisallament per a cada paperot i condicions d'agitació, s'ha relacionat amb Xm, SEC, tD, consum de potència, potència instal·lada i fracció cel·lulòsica. El factor de cisallament és un paràmetre útil per a quantificar les forces globals implicades en la desintegració.

Effects of endogenous flour lipids on the quality of semisweet biscuits

Fractionation and reconstitution techniques were used to study the contribution of enclogenous flour lipids to the quality of semisweet (Rich Tea-type) biscuits. Biscuit flour was defatted with chloroform and baked with bakery fat but without enclogenous lipid addition. Semisweet biscuits baked from defatted flour were flatter, denser, and harder and showed collapse of gas cells during baking when compared with control biscuits. Defatted flour semisweet doughs exhibited a different rheological behavior from the control samples showing higher storage and loss moduli (G' and G" values), that is, high viscoelasticity. Functionality was restored when total nonstarch flour lipids were added back to defatted flour. Both the polar and nonpolar lipid fractions had positive effects in restoring flour quality, but the polar lipid fraction was of greatest benefit. Both fractions were needed for complete restoration of both biscuit quality and dough rheological characteristics.

Effects of endogenous flour lipids on the quality of short-dough biscuits

Fractionation and reconstitution techniques were used to study the contribution of endogenous flour lipids to the quality of short-dough (shortcake type) biscuits. Biscuit flour was defatted with chloroform and baked with bakery fat, but without endogenous lipid. Short-dough biscuits baked from defatted flour had smaller diameters, and were flatter, denser and harder than control biscuits. Defatted flour shortcake doughs exhibited different rheological behaviour from the control samples, showing higher storage and loss moduli (G' and G" values), ie higher viscoelasticity. Functionality was restored when total non-starch flour lipids were added back to defatted flour. The polar lipid fraction had a positive effect in restoring flour quality whereas the non-polar lipid fraction had no effect. Both fractions were needed for complete restoration of both biscuit quality and dough rheological characteristics. A study of the microstructure of defatted biscuits revealed that their gluten protein was more hydrated and developed than the gluten of the control biscuits. This conclusion was supported by the higher water absorption of the defatted gluten. (C) 2004 Society of Chemical Industry.