The influence of curing conditions on the mechanical performance of concrete made with recycled concrete waste

Research on the use of Construction and Demolition Waste (CDW) as recycled aggregate (in particular crushed concrete) for the production of new concrete has by now established the feasibility of this environmentally-friendly use of otherwise harmful waste. However, contrary to conventional concrete (CC), no large applications of concrete made with recycled concrete have been made and there is still a lack of knowledge in some areas of production and performance of recycled aggregate concrete (RAC). One issue concerns curing conditions: these greatly affect the performance of concrete made on site and some potential users of RAC wonder how RAC is affected by far-from-ideal curing conditions. This paper shows the main results of experiments to determine the influence of different curing conditions on the mechanical performance of concrete made with coarse recycled aggregate from crushed concrete. The properties analyzed include compressive strength, splitting tensile strength, modulus of elasticity, and abrasion resistance. The general conclusion in terms of mechanical performance is that RAC is affected by curing conditions roughly in the same way as CC. (C) 2011 Elsevier Ltd. All rights reserved.

Behavior of Carbonate Rocks as Concrete Aggregates, HR-15, 1962

The problem of determining the suitability of carbonate rocks as concrete aggregates is extremely complex and calls for more new data than has been available or obtainable from usual methods. Since 1955 the approach which has served as a primary basis for the project has been to gather as much new information as possible to apply to the problem. New information obtained by new and different techniques provides better understanding. This approach was decided on since, in all prior studies, a standard petrographic and petrologic approach correlated in many instances with standard engineering tests did not provide the answer in Iowa or elsewhere. One can theorize that concrete fails (excluding external causes such as traffic, foundation failure, etc.) because of stresses of internal origin. The stresses can be of a physical nature, such as frost action, or result from chemical activity such as the alkali aggregate reaction. If, as service records show, the aggregate is considered the cause of distress in concrete, it will without doubt be the manner in which an aggregate can create or contribute to stress of internal origin by physical or chemical means. Therefore the main emphasis was placed on studying physical and chemical properties of aggregates as well as the behavior of carbonate rocks in concrete environments. Although standard geologic and engineering methods were also utilized, the approach adopted required considerable effort in devising new techniques and methods. This report is intended to be a detailed summary of the research performed. Whenever possible, the work accomplished will be summarized and all pertinent data will be included. For further details, reference to the various theses and publications transmitted with this report or at previous times will be made wherever possible.

Evaluation of Asphalt Mixes Made from Reclaimed Concrete Aggregates, MLR-85-07, 1986

Three comparable hot mixed asphalt paving mixes were produced using two different aggregates produced from reclaimed portland cement concrete paving and one from a crushed limestone aggregate. These were subjected both dry and soaked to indirect tensile tests to determine the wet strength retention. One mix made from reclaimed concrete demonstrated a slightly better strength retention than the limestone mix and the other less. Satisfactory asphalt paving mixes can be produced from reclaimed concrete pavements but the increased asphalt demand (about 1%) negates part of the potential savings.

The encore project: sustainable solutions for cementitious materials

Since concrete is the most widely utilized construction material, several solutions are currently being developed and investigated for enhancing the sustainability of cementitious materials. One of these solutions is based on producing Recycled Concrete Aggregates (RCA) from existing concrete members resulting by either industrial processes or demolitions of existing structures as a whole. Moreover, waste resulting from industrial processes other than the building construction (i.e., tire recycling, production of steel, powders resulting from other depuration processes) are also being considered as possible low-impact constituents for producing structural concrete and Fiber-Reinforced Cementitious Composites (FRCC). Furthermore, the use of natural fibers is another option for producing environmentally-friendly and cost-effective materials, depending on the local availability of raw materials. To promote the use of concretes partially composed of recycled constituents, their influence on the mechanical and durability performance of these concretes have to be deeply investigated and correlated. This was the main goal of the EnCoRe Project (www.encore-fp7.unisa.it), a EU-funded initiative, whose activities and main findings are summarized in this paper.

Guide to Cement-Based Integrated Pavement Solutions, August 2011

This guide provides a clear, concise, and cohesive presentation of cement-bound materials options for 10 specific engineering pavement applications: new concrete pavements, concrete overlays, previous concrete, precast pavements, roller-compacted concrete, cement-treated base, full-depth reclamation with cement, cement-modified soils, recycled concrete aggregates, and repair and restoration. Each application is presented as a method for meeting specific design and construction objectives that today’s pavement practitioners must accomplish. The benefits, considerations, brief description, and summary of materials, design, and construction requirements, as well as a list of sustainable attributes, are provided for every solution. This guide is intended to be short, simple, and easy to understand. It was designed so that the most up-to-date and relevant information is easily extractable. It is not intended to be used as a design guide for any of the applications identified herein. Recommendations for additional information that can provide such details are given at the end of each solution discussion. The intended audience is practitioners, including engineers and managers who face decisions regarding what materials to specify in the pavement systems they design or manage. The audience also includes city and county engineers, along with the A/E firms that often represent them, and state DOT engineers at all levels who are seeking alternatives in this era of changing markets.

Physical, chemical and mineralogical properties of fine recycled aggregates made from concrete waste

This paper assesses the physical, chemical and mineralogical characteristics of fine recycled aggregates obtained from crushed concrete waste, comparing them with two types of natural fine aggregates from different origins. A commercial concrete was jaw crushed, and the effect of different aperture sizes on the particle size distribution of the resulting aggregates was evaluated. The density and water absorption of the recycled aggregates was determined and a model for predicting water absorption over time is proposed. Both natural and recycled aggregates were characterized regarding bulk density and fines content. Recycled aggregates were additionally characterized by XRD, SEM/EDS and DTA/TG of individual size fractions. The results show that natural and recycled fine aggregates have very different characteristics. This should be considered in potential applications, both in terms of the limits for replacing amounts and of the rules and design criteria of the manufactured products. (C) 2015 Elsevier Ltd. All rights reserved.

Classification of recycled sands and their applications as fine aggregates for concrete and bituminous mixtures

As a result of the drive towards waste-poor world and reserving the non-renewable materials, recycling the construction and demolition materials become very essential. Now reuse of the recycled concrete aggregate more than 4 mm in producing new concrete is allowed but with natural sand a fine aggregate while. While the sand portion that represent about 30\% to 60\% of the crushed demolition materials is disposed off. To perform this research, recycled concrete sand was produced in the laboratory while nine recycled sands produced from construction and demolitions materials and two sands from natural crushed limestone were delivered from three plants. Ten concrete mix designs representing the concrete exposition classes XC1, XC2, XF3 and XF4 according to European standard EN 206 were produced with partial and full replacement of natural sand by the different recycled sands. Bituminous mixtures achieving the requirements of base courses according to Germany standards and both base and binder courses according to Egyptian standards were produced with the recycled sands as a substitution to the natural sands. The mechanical properties and durability of concrete produced with the different recycled sands were investigated and analyzed. Also the volumetric analysis and Marshall test were performed hot bituminous mixtures produced with the recycled sands. According to the effect of replacement the natural sand by the different recycled sands on the concrete compressive strength and durability, the recycled sands were classified into three groups. The maximum allowable recycled sand that can be used in the different concrete exposition class was determined for each group. For the asphalt concrete mixes all the investigated recycled sands can be used in mixes for base and binder courses up to 21\% of the total aggregate mass.

Concretes and mortars recycled with water treatment sludge and construction and demolition rubble

There are about 7500 water treatment plants in Brazil. The wastes these plants generate in their decantation tanks and filters are discharged directly into the same brooks and rivers that supply water for treatment. Another serious environmental problem is the unregulated disposal of construction and demolition rubble, which increases the expenditure of public resources by degrading the urban environment and contributing to aggravate flooding and the proliferation of vectors harmful to public health. In this study, an evaluation was made of the possibility of recycling water treatment sludge in construction and demolition waste recycling plants. The axial compressive strength and water absorption of concretes and mortars produced with the exclusive and joint addition of these two types of waste was also determined. The ecoefficiency of this recycling was evaluated by determining the concentration of aluminum in the leached extract resulting from the solubilization of the recycled products. The production of concretes and mortars with the joint addition of water treatment sludge and recycled concrete rubble aggregates proved to be a viable recycling alternative from the standpoint of axial compression strength, modulus of elasticity, water absorption and tensile strength by the Brazilian test method. (C) 2008 Elsevier Ltd. All rights reserved.

Concrete deterioration due to sulfide-bearing aggregates

Dans la région de Trois-Rivières (Québec, Canada), plus de 1 000 bâtiments résidentiels et commerciaux montrent de graves problèmes de détérioration du béton. Les problèmes de détérioration sont liés à l’oxydation des sulfures de fer incorporés dans le granulat utilisé pour la confection du béton. Ce projet de doctorat vise à mieux comprendre les mécanismes responsables de la détérioration de béton incorporant des granulats contenant des sulfures de fer, et ce afin de développer une méthodologie pour évaluer efficacement la réactivité potentielle de ce type de granulats. Un examen pétrographique détaillé de carottes de béton extraites de fondations résidentielles montrant différents degré d’endommagement a été réalisé. Le granulat problématique contenant des sulfures de fer a été identifié comme un gabbro à hypersthène incorporant différentes proportions (selon les différentes localisations dans les deux carrières d’origine) de pyrrhotite, pyrite, chalcopyrite et pentlandite. Les produits de réaction secondaires observés dans les échantillons dégradés comprennent des formes minérales de "rouille", gypse, ettringite et thaumasite. Ces observations ont permis de déterminer qu’en présence d’eau et d’oxygène, la pyrrhotite s’oxyde pour former des oxyhydroxides de fer et de l’acide sulfurique qui provoquent une attaque aux sulfates dans le béton. Tout d’abord, la fiabilité de l’approche chimique proposée dans la norme européenne NF EN 12 620, qui consiste à mesurer la teneur en soufre total (ST,% en masse) dans le granulat pour détecter la présence (ou non) de sulfures de fer, a été évaluée de façon critique. Environ 50% (21/43) des granulats testés, représentant une variété de types de roches/lithologies, a montré une ST > 0,10%, montrant qu’une proportion importante de types de roches ne contient pas une quantité notable de sulfure, qui, pour la plupart d’entre eux, sont susceptibles d’être inoffensifs dans le béton. Ces types de roches/granulats nécessiteraient toutefois d’autres tests pour identifier la présence potentielle de pyrrhotite compte tenu de la limite de ST de 0,10 % proposée dans les normes européennes. Basé sur une revue exhaustive de la littérature et de nombreuses analyses de laboratoire, un test accéléré d’expansion sur barres de mortier divisé en deux phases a ensuite été développé pour reproduire, en laboratoire, les mécanismes de détérioration observés à Trois-Rivières. Le test consiste en un conditionnement de 90 jours à 80°C/80% RH, avec 2 cycles de mouillage de trois heures chacun, par semaine, dans une solution d’hypochlorite de sodium (eau de javel) à 6% (Phase I), suivi d’une période pouvant atteindre 90 jours de conditionnement à 4°C/100 % HR (Phase II). Les granulats ayant un potentiel d’oxydation ont présenté une expansion de 0,10 % au cours de la Phase I, tandis que la formation potentielle de thaumasite est détectée par le regain rapide de l’expansion suivi par la destruction des échantillons durant la Phase II. Un test de consommation d’oxygène a également été modifié à partir d’un test de Drainage Minier Acide, afin d’évaluer quantitativement le potentiel d’oxydation des sulfures de fer incorporés dans les granulats à béton. Cette technique mesure le taux de consommation d’oxygène dans la partie supérieure d’un cylindre fermé contenant une couche de matériau compacté afin de déterminer son potentiel d’oxydation. Des paramètres optimisés pour évaluer le potentiel d’oxydation des granulats comprennent une taille de particule inférieure à 150 μm, saturation à 40 %, un rapport de 10 cm d’épaisseur de granulat par 10 cm de dégagement et trois heures d’essai à 22ᵒC. Les résultats obtenus montrent que le test est capable de discriminer les granulats contenant des sulfures de fer des granulats de contrôle (sans sulfures de fer) avec un seuil limite fixé à 5% d’oxygène consommé. Finalement, un protocole d’évaluation capable d’estimer les effets néfastes potentiels des granulats à béton incorporant des sulfures de fer a été proposé. Le protocole est divisé en 3 grandes phases: (1) mesure de la teneur en soufre total, (2) évaluation de la consommation d’oxygène, et (3) un test accéléré d’expansion sur barres de mortier. Des limites provisoires sont proposées pour chaque phase du protocole, qui doivent être encore validées par la mise à l’essai d’un plus large éventail de granulats.

Fly Ash Concrete Compressive Strength and Freeze-Thaw Durability, MLR-81-06, 1981

The current study investigated the effect of fly ash class, source and amount on the compressive strength and freeze-thaw durability of fly ash concrete. Concrete aggregates of varying quality were also included as test variables. The current results and those obtained from previous laboratory and field work indicate that compressive strength can·be affected by fly ash class, source and amount while aggregate quality is shown to have no effect on strength. Freeze-thaw durability of fly ash concrete is strongly affected by aggregate quality and to a lesser degree by fly ash class, amount and source.

Evaluation of the performance and cost-effectiveness of pavement sections containing open-graded base courses

Moisture induced distresses have been the prevalent distress type affecting the deterioration of both asphalt and concrete pavement sections. While various surface techniques have been employed over the years to minimize the ingress of moisture into the pavement structural sections, subsurface drainage components like open-graded base courses remain the best alternative in minimizing the time the pavement structural sections are exposed to saturated conditions. This research therefore focuses on assessing the performance and cost-effectiveness of pavement sections containing both treated and untreated open-graded aggregate base materials. Three common roadway aggregates comprising of two virgin aggregates and one recycled aggregate were investigated using four open-ended gradations and two binder types. Laboratory tests were conducted to determine the hydraulic, mechanical and durability characteristics of treated and untreated open-graded mixes made from these three aggregate types. Results of the experimental program show that for the same gradation and mix design types, limestone samples have the greatest drainage capacity, stability to traffic loads and resistance to degradation from environmental conditions like freeze-thaw. However, depending on the gradation and mix design used, all three aggregate types namely limestone, natural gravel and recycled concrete can meet the minimum coefficient of hydraulic conductivity required for good drainage in most pavements. Tests results for both asphalt and cement treated open-graded samples indicate that a percent air void content within the range of 15-25 will produce a treated open-graded base course with sufficient drainage capacity and also long term stability under both traffic and environmental loads. Using the new Mechanistic and Empirical Design Guide software, computer simulations of pavement performance were conducted on pavement sections containing these open-graded base aggregate base materials to determine how the MEPDG predicted pavement performance is sensitive to drainage. Using three truck traffic levels and four climatic regions, results of the computer simulations indicate that the predicted performance was not sensitive to the drainage characteristics of the open-graded base course. Based on the result of the MEPDG predicted pavement performance, the cost-effectiveness of the pavement sections with open-graded base was computed on the assumption that the increase service life experienced by these sections was attributed to the positive effects of subsurface drainage. The two cost analyses used gave two contrasting results with the one indicating that the inclusion of open-graded base courses can lead to substantial savings.

Estudio de hormigones reciclados no estructurales fabricados con árido reciclado mixto : propiedades mecánicas y expansión debida al contenido de sulfatos

El objetivo principal de este trabajo de investigación es estudiar las posibilidades de utilización del árido reciclado mixto para un hormigón reciclado en aplicaciones no estructurales, justificando mediante la experimentación la validez para esta aplicación, tanto del árido reciclado como del hormigón reciclado. Esta tesis se centró en los aspectos más restrictivos y limitativos en la utilización de los áridos mixtos en hormigón reciclado, basándose tanto en la normativa internacional existente como en los resultados obtenidos en los estudios bibliográficos consultados. La primera tarea realizada fue la caracterización completa de las propiedades del árido reciclado mixto, recogiendo especialmente los siguientes aspectos: granulometría, contenido de finos, absorción y densidades, composición del árido reciclado, índice de lajas, coeficiente de Los Ángeles, partículas ligeras y contenido de sulfatos. De este estudio de los áridos reciclados, se han destacado relaciones entre las propiedades. Las diferentes correlaciones permiten proponer criterios de calidad de un árido reciclado mixto para un hormigón reciclado. Se ha elegido un árido reciclado mixto entre los estudiados, de características límite admisibles, para obtener resultados conservadores sobre el hormigón reciclado fabricado con él. En una segunda etapa, se ha realizado un estudio de dosificación completo del hormigón reciclado, evaluando la consistencia del hormigón en estado fresco y la resistencia a compresión del hormigón en estado endurecido y se ha comparado con las mismas propiedades de un hormigón convencional. Se ha analizado la capacidad de absorción del árido conseguida con los métodos de presaturación empleados y en función de su estado de humedad, para poder evaluar las relaciones agua/cemento totales y efectivas del hormigón. Se ha estudiado el efecto de estos dos parámetros tanto en la consistencia como en la resistencia del hormigón reciclado. Finalmente, se ha estudiado el hormigón fabricado con un 50% y 100% de una partida de árido reciclado mixto de calidad admisible y se han ensayado las siguientes propiedades: consistencia, resistencia a compresión, resistencia a tracción indirecta, módulo de elasticidad dinámico, cambios de longitud, porosidad abierta y microscopía. Para analizar el efecto de los sulfatos, se han añadido artificialmente cantidades de yeso controladas en el hormigón reciclado. Se fabricaron hormigones con dos tipos de cemento, un cemento CEM I 42,5 R con elevado contenido de C3A, que debería dar lugar a expansiones mayores y un cemento con adiciones puzolánicas CEM II A-P 42,5 R, que atenuaría el comportamiento expansivo en el hormigón. Los resultados finales indican que la utilización del árido reciclado mixto en proporciones de hasta un 50%, permiten cubrir la gama de resistencias más exigentes dentro del hormigón no estructural. El contenido de sulfatos puede variar desde un 0,8% hasta un 1,9%, según el tipo de cemento y la proporción de sustitución del árido natural por árido reciclado mixto. Tanto en el caso del árido reciclado como en el hormigón, se ha realizado un estudio comparativo entre el conjunto de datos recopilados en la bibliografía y los obtenidos en este estudio experimental. En varias propiedades del hormigón reciclado, se han comparado los resultados con las fórmulas de la Instrucción EHE-08, para establecer unos coeficientes de corrección a aplicar a un hormigón reciclado con fines no estructurales. The main objective of this investigation work is to study the possibilities of using recycled mixed aggregate for a recycled concrete in non structural applications, justifying by means of experimentation both the validity of the recycled aggregate and recycled concrete. This thesis focused on the most restrictive and limiting aspects in the mixed aggregate use in recycled concrete, on the basis of the international standards as well on the results obtained in the bibliographic studies consulted. The first task achieved was the complete charcaterization of the mixed recycled aggregate properties, specially the following aspects: grain size analysis, fines content, absorption and densities, recycled aggregate composition, flakiness index, Los Angeles coefficient, lightweight particles and sulphate content. From this study, correlations between the properties were highlighted. The different correlations make possible to propose quality criterions for recycled mixed aggregate in concrete. Among the recycled aggregates studied, one of acceptable characteristics but near the limits established, was chosen to obtain conservative results in the recycled concrete made with it. In a second step, a complete recycled concrete mix design was made, to evaluate concrete consistency in the fresh state and concrete compressive strength in the hardened state and its properties were compared to those of a control concrete. The aggregate absorption capacity was analized with the presaturation methods achieved and in function of its state of humidity, to evaluate the total and effective water/cement ratios. The effect of these two parameters, both in consistency and compressive strength of recycled concrete, was studied. Finally, the concrete made with 50% and 100% of the elected recycled mixed aggregate was studied and the following concrete properties were tested: consistency, compressive strength, tensile strength, dynamic modulus of elasticity, length changes, water absorption under vacuum and microscopy. To analize the effect of sulphate content, some controlled quantities of gypsum were artificially added to the recycled concrete. Concretes with two types of cement were made, a cement CEM I 42,5 R with a high content of C3A, that would lead to major expansions and a cement with puzzolanic additions CEM II A-P 42,5 R that would lower the expansive behaviour of concrete. The final results indicate that the use of mixed recycled aggregate in proportions up to 50% make possible to cover the overall demanding strengths within the non structural concrete. Sulphates content can range between 0,8% and 1,9%, in function of the type of cement and the proportion of natural aggregate replacement by mixed recycled one. Both in the case of recycled aggregate and concrete, a comparative study was made between the data coming from the bibliography and those obtained in the experimental study. In several recycled concrete properties, the results were compared to the formulas of Spanish Instruction of Structural Concrete (Instruction EHE-08), to establish some correction coefficients to apply for a non structural recycled concrete.

Estudio de hormigón autocompactante con árido reciclado

La tesis doctoral “Estudio de hormigón autocompactante con árido reciclado” realizada dentro del programa de doctorado de la Universidad Politécnica de Madrid “Máster en técnicas experimentales avanzadas en la ingeniería civil”, investiga la sustitución de áridos gruesos naturales por reciclados en hormigones autocompactantes, para demostrar la posibilidad de utilización de este tipo de árido en la fabricación de hormigones autocompactantes. En cuanto a la línea experimental adoptada, la primera fase corresponde a la caracterización de los cementos y de los áridos naturales y reciclados. En ella se han obtenido las principales características físicas y mecánicas. Una vez validadas las características de todos los materiales y adoptada una dosificación de hormigón autocompactante, se han elaborado cuatro dosificaciones con cuatro grados de incorporación de árido reciclado cada una, y una dosificación con seis grados de incorporación de árido reciclado. Fabricándose un total de 22 tipos de hormigón diferentes, sin contar todas las amasadas iniciales hasta la consecución de un hormigón autocompactante. Las cinco dosificaciones se han dividido en dos grupos para poder analizar con mayor grado de definición las características de cada uno. El primer grupo es aquel que contienen los hormigones con diferentes relaciones a/c, que incluye a la muestra A (a/c=0.55), muestra D (a/c=0.50) y muestra E (a/c=0.45). Por el contrario, el segundo grupo dispone de una relación fija de a/c=0.45 pero diferentes relaciones a/c efectivas, ya que algunas de las muestras disponen de un contenido de agua que permite contrarrestar la mayor absorción del árido reciclado. Estando en este grupo la muestra E (sin agua adicional), la muestra H (con presaturación de los áridos) y la muestra I (con un aporte de agua junto con el agua de amasado. Una vez fabricados los hormigones, se pasa a la segunda fase del estudio correspondiente a la caracterización del hormigón en estado fresco. En esta fase se han llevado a cabo los ensayos de escurrimiento, escurrimiento con anillo japonés, ensayo embudo en V y embudo V a los 5 minutos. Todos estos ensayos permiten evaluar la autocompactabilidad del hormigón según el anejo 17 de la EHE-08. La tercera fase del estudio se centra en la caracterización de los hormigones en estado endurecido, evaluando las características resistentes del hormigón. Para ello, se han realizado los ensayos de resistencia a compresión, a tracción, módulo de elasticidad y coeficiente de Poisson. En la cuarta y última fase, se han analizado la durabilidad de los hormigones, debido que a pesar de ofrecer una adecuada autocompactabilidad y resistencia mecánica, se debe de obtener un hormigón con una correcta durabilidad. Para tal fin, se ha determinado la resistencia a la penetración de agua bajo presión y carbonatación de las probetas. Este último ensayo se ha realizado teniendo en cuenta las condiciones del denominado método natural, con una exposición al ambiente de 90 días y 365 días. Con todos estos resultados se elaboraron las conclusiones derivadas de la investigación, demostrándose la posibilidad de fabricación de hormigones autocompactantes con árido reciclado (HACR) con sustituciones de hasta un 40%, e incluso dependiendo de la relación a/c con sustituciones del 60% y el 80%. ABSTRACT The doctoral thesis titled Analysis of self-compacting concrete with recycled aggregates, has been developed in accordance with the doctoral program: Master degree in advanced experimental techniques in civil engineering, at UPM. It investigates the possibility of replacing natural coarse aggregates with recycled coarse aggregates, in the field of self-compacting concrete. The aim of this dissertation is to analyze the possibility of using recycled coarse aggregates in the manufacture process of self-compacting concretes. Regarding the experimental part, the first phase refers to mechanical and physical characterization of some materials such as cement, natural aggregates and recycled aggregates. Once the characteristics of all materials have been validated and the mixing proportions have been adopted, four different mixes are elaborated by using four dosage rates of recycled aggregates in each one of the samples. Moreover, an additional sample consisting of six different dosages of recycled aggregates is considered. A total number of 22 concrete specimens have been manufactured, without including all the initial kneading samples used to obtain this type of self-compacting concrete. The aforementioned mixes have been divided in two different groups to be able to analyze with more definition. The first group is the one in which the concrete contains different values of the water - cement ratio. It includes the next samples: A (w/c=0.55), D (w/c=0.50) and E (w/c=0.45). The second group has a fixed water -cement ratio, w/c=0.45, but a different effective water - cement ratio, since some of the samples have a water content that enables to offset the major absorption of the recycled aggregates, being in this group the mixing E (without additional water), the mixing H (with saturated recycled aggregate) and the mixing I (with an additional water content to the existing kneading water). Once the concrete samples have been manufactured, the following section deals with the characterization of the concrete in fresh conditions. To accomplish this, several characterization tests are carried out such as the slump-flow test, test slump flow with Japanese ring, test V-funnel and V-funnel to 5 minutes. These tests are used to assess the self-compacting conditions according to the annex 17 of the EHE-08 The third phase of the study focuses on the mechanical characterization, the assessment of the strength properties of the concrete such as compressive strength, tensile strength, modulus of elasticity and Poisson´s ratio. Within the fourth and last phase, durability of the concrete is evaluated. This fact is motivated by the need to obtain not only good self-compacting and mechanical strength properties, but also adequate durability conditions. To accomplish the aforementioned durability, resistance of the samples under certain conditions such as water penetration pressure and carbonation, has been obtained. The latter test has been carried out taking into account the natural method, with an exhibition period to the environment of 90 days and 365 days. Through the results coming from this research work, it has been possible to obtain the main conclusions. It has been demonstrated the possibility to manufacture self-compacting concrete by using recycled aggregates with replacement rates up to 40% or, depending on the w/c ratio, rates of 60% and 80% might be reached.

Performance of electric and microwave batch plant moisture meters in determining the moisture contents of fine-aggregate materials for concrete production /

Mode of access: Internet.

Assessment and Life-Cycle Analysis of Recycled Materials for Sustainable Highway

Recycled materials replacing part of virgin materials in highway applications has shown great benefits to the society and environment. Beneficial use of recycled materials can save landfill places, sparse natural resources, and energy consumed in milling and hauling virgin materials. Low price of recycled materials is favorable to cost-saving in pavement projects. Considering the availability of recycled materials in the State of Maryland (MD), four abundant recycled materials, recycled concrete aggregate (RCA), recycled asphalt pavement (RAP), foundry sand (FS), and dredged materials (DM), were studied. A survey was conducted to collect the information of current usage of the four recycled materials in States’ Department of Transportation (DOTs). Based on literature review, mechanical and environmental properties, recommendations, and suggested test standards were investigated separately for the four recycled materials in different applications. Constrains in using these materials were further studied in order to provide recommendations for the development of related MD specifications. To measure social and environmental benefits from using recycled materials, life-cycle assessment was carried out with life-cycle analysis (LCA) program, PaLATE, and green highway rating system, BEST-in-Highway. The survey results indicated the wide use of RAP and RCA in hot mix asphalt (HMA) and graded aggregate base (GAB) respectively, while FS and DM are less used in field. Environmental concerns are less, but the possibly low quality and some adverse mechanical characteristics may hinder the widely use of these recycled materials. Technical documents and current specifications provided by State DOTs are good references to the usage of these materials in MD. Literature review showed consistent results with the survey. Studies from experimental research or site tests showed satisfactory performance of these materials in highway applications, when the substitution rate, gradation, temperature, moisture, or usage of additives, etc. meet some requirements. The results from LCA revealed significant cost savings in using recycled materials. Energy and water consumption, gas emission, and hazardous waste generation generally showed reductions to some degree. Use of new recycled technologies will contribute to more sustainable highways.