New Iowans Pilot Project, 2001

Governor Vilsack and Lt. Governor Pederson are encouraging the development of a strategic community plan to encourage a smooth transition for bringing skilled workers and their families to Iowa from other countries. Skilled workers from other countries can provide a valuable resource to Iowa employers and can add cultural richness and diversity to Iowa's communities. New Iowans can help Iowa's communities, businesses, and economy grow

Traffic Signal Inventory Project, 2001

The Center for Transportation Research and Education performed a traffic signal inventory study for the Iowa Department of Transportation. The purpose of this study was to determine the level of compliance with the Manual on Uniform Traffic Control Devices (MUTCD) and other industry standards of traffic signals on the state highway system. Signals were randomly selected throughout the State of Iowa. Only signals in cities with a population less than 5,000 were considered. Several intersections need to be addressed immediately to correct clearance timing settings. Red clearance intervals were frequently too short. A handful of intersections had inadequate pedestrian clearance times. Six intersections had at least one yellow clearance interval that did not meet Institute of Transportation Engineers standards. Some of the intersections likely would not meet traffic signal warrants and should be investigated for possible removal. The most common problem found with traffic signals was a lack of maintenance. Many of the signals had at least one of the following problems: burned out lights (signals and/or pedestrian heads), pedestrian lenses in need of replacement, dirty cabinet/missing or poor filter, missing visors, or inoperative pedestrian push buttons. Timing sheets were frequently missing or out of date. Another frequent noncompliance issue was the use of backplates. The MUTCD states that backplates should be used on signals viewed against a bright sky. The majority of signals inventoried did not have backplates on the mast-arm mounted signals. The timing at some intersections could likely be improved by reducing the cycle length. Where there were multiple signals in close proximity rarely was there any attempt at signal coordination. Finally, a number of intersections had equipment that by today’s standards would be considered obsolete.

Design,implementation and use of an Internet kiosk as an an information system for CNC machinists

Tätä diplomityötä sponsoroi suuri Isobritannialainen lentokoneteollisuudessa toimiva yritys, joka huomasi että globaalin tuotantostrategian ollessa painopisteenä ja tietoteknisten järjestelmien kuten CAD/CAM ollessa merkittävänä osana tuotantoa, on löydettävä ymmärrys siitä, mitkä ovat tuotannon tietojärjestelmien tarpeet ja onko niiden kehittämisestä hyötyä yritykselle.Diplomityössä selitetään Internet teknologiaan perustuvan kioskin kehittämisestä tietotukijärjestelmäksi tuotanto-osastolle, jossa valmistetaan moottorin osia CNC-koneilla. Kioskeissa on piirteitä, jotka voisivat osoittautua hyödyllisiksi myös tuotantoympäristöissä ja siksi tässä työssä tutkitaan kioskiin perustuvaa lähestymistapaa tuotantoympäristöön sovellettuna.Diplomityö kuvaa informaatiokioskin kehittämistä alkaen alkuvaatimusten keruusta tietojärjestelmää varten, tietojärjestelmän suunnittelu- ja kehitysvaiheen sekä lopuksi analysoi kioskin onnistuneisuutta tuotantoympäristössä käytettävyystutkimuksen avulla, joka suoritettiin sen jälkeen kun kioski oli implementoitu tehtaassa.Johtopäätökset osoittavat, että kioski on hyvin implementoitavissa tuotantoympäristöön ja todistaa, että tuotantoinformaation jakelu sähköisessä muodossa on huomattavasti tehokkaampaa kuin paperilla. Käyttäjien kommentit osoittavat että kioski on sopiva heidän tietotarpeisiinsa ja siitä on hyötyä heidän työlleen. Kioski tarjoaa hyötyjä tuotantotason lisäksi myös johtotasolle.

Towards increased productivity and quality in software development using agile, lean and collaborative approaches

Dagens programvaruindustri står inför alltmer komplicerade utmaningar i en värld där programvara är nästan allstädes närvarande i våra dagliga liv. Konsumenten vill ha produkter som är pålitliga, innovativa och rika i funktionalitet, men samtidigt också förmånliga. Utmaningen för oss inom IT-industrin är att skapa mer komplexa, innovativa lösningar till en lägre kostnad. Detta är en av orsakerna till att processförbättring som forskningsområde inte har minskat i betydelse. IT-proffs ställer sig frågan: “Hur håller vi våra löften till våra kunder, samtidigt som vi minimerar vår risk och ökar vår kvalitet och produktivitet?” Inom processförbättringsområdet finns det olika tillvägagångssätt. Traditionella processförbättringsmetoder för programvara som CMMI och SPICE fokuserar på kvalitets- och riskaspekten hos förbättringsprocessen. Mer lättviktiga metoder som t.ex. lättrörliga metoder (agile methods) och Lean-metoder fokuserar på att hålla löften och förbättra produktiviteten genom att minimera slöseri inom utvecklingsprocessen. Forskningen som presenteras i denna avhandling utfördes med ett specifikt mål framför ögonen: att förbättra kostnadseffektiviteten i arbetsmetoderna utan att kompromissa med kvaliteten. Den utmaningen attackerades från tre olika vinklar. För det första förbättras arbetsmetoderna genom att man introducerar lättrörliga metoder. För det andra bibehålls kvaliteten genom att man använder mätmetoder på produktnivå. För det tredje förbättras kunskapsspridningen inom stora företag genom metoder som sätter samarbete i centrum. Rörelsen bakom lättrörliga arbetsmetoder växte fram under 90-talet som en reaktion på de orealistiska krav som den tidigare förhärskande vattenfallsmetoden ställde på IT-branschen. Programutveckling är en kreativ process och skiljer sig från annan industri i det att den största delen av det dagliga arbetet går ut på att skapa något nytt som inte har funnits tidigare. Varje programutvecklare måste vara expert på sitt område och använder en stor del av sin arbetsdag till att skapa lösningar på problem som hon aldrig tidigare har löst. Trots att detta har varit ett välkänt faktum redan i många decennier, styrs ändå många programvaruprojekt som om de vore produktionslinjer i fabriker. Ett av målen för rörelsen bakom lättrörliga metoder är att lyfta fram just denna diskrepans mellan programutvecklingens innersta natur och sättet på vilket programvaruprojekt styrs. Lättrörliga arbetsmetoder har visat sig fungera väl i de sammanhang de skapades för, dvs. små, samlokaliserade team som jobbar i nära samarbete med en engagerad kund. I andra sammanhang, och speciellt i stora, geografiskt utspridda företag, är det mera utmanande att införa lättrörliga metoder. Vi har nalkats utmaningen genom att införa lättrörliga metoder med hjälp av pilotprojekt. Detta har två klara fördelar. För det första kan man inkrementellt samla kunskap om metoderna och deras samverkan med sammanhanget i fråga. På så sätt kan man lättare utveckla och anpassa metoderna till de specifika krav som sammanhanget ställer. För det andra kan man lättare överbrygga motstånd mot förändring genom att introducera kulturella förändringar varsamt och genom att målgruppen får direkt förstahandskontakt med de nya metoderna. Relevanta mätmetoder för produkter kan hjälpa programvaruutvecklingsteam att förbättra sina arbetsmetoder. När det gäller team som jobbar med lättrörliga och Lean-metoder kan en bra uppsättning mätmetoder vara avgörande för beslutsfattandet när man prioriterar listan över uppgifter som ska göras. Vårt fokus har legat på att stöda lättrörliga och Lean-team med interna produktmätmetoder för beslutsstöd gällande så kallad omfaktorering, dvs. kontinuerlig kvalitetsförbättring av programmets kod och design. Det kan vara svårt att ta ett beslut att omfaktorera, speciellt för lättrörliga och Lean-team, eftersom de förväntas kunna rättfärdiga sina prioriteter i termer av affärsvärde. Vi föreslår ett sätt att mäta designkvaliteten hos system som har utvecklats med hjälp av det så kallade modelldrivna paradigmet. Vi konstruerar även ett sätt att integrera denna mätmetod i lättrörliga och Lean-arbetsmetoder. En viktig del av alla processförbättringsinitiativ är att sprida kunskap om den nya programvaruprocessen. Detta gäller oavsett hurdan process man försöker introducera – vare sig processen är plandriven eller lättrörlig. Vi föreslår att metoder som baserar sig på samarbete när processen skapas och vidareutvecklas är ett bra sätt att stöda kunskapsspridning på. Vi ger en översikt över författarverktyg för processer på marknaden med det förslaget i åtanke.

Design, implementation and application of a generic framework for integrated regional land-use modeling

Land use is a crucial link between human activities and the natural environment and one of the main driving forces of global environmental change. Large parts of the terrestrial land surface are used for agriculture, forestry, settlements and infrastructure. Given the importance of land use, it is essential to understand the multitude of influential factors and resulting land use patterns. An essential methodology to study and quantify such interactions is provided by the adoption of land-use models. By the application of land-use models, it is possible to analyze the complex structure of linkages and feedbacks and to also determine the relevance of driving forces. Modeling land use and land use changes has a long-term tradition. In particular on the regional scale, a variety of models for different regions and research questions has been created. Modeling capabilities grow with steady advances in computer technology, which on the one hand are driven by increasing computing power on the other hand by new methods in software development, e.g. object- and component-oriented architectures. In this thesis, SITE (Simulation of Terrestrial Environments), a novel framework for integrated regional sland-use modeling, will be introduced and discussed. Particular features of SITE are the notably extended capability to integrate models and the strict separation of application and implementation. These features enable efficient development, test and usage of integrated land-use models. On its system side, SITE provides generic data structures (grid, grid cells, attributes etc.) and takes over the responsibility for their administration. By means of a scripting language (Python) that has been extended by language features specific for land-use modeling, these data structures can be utilized and manipulated by modeling applications. The scripting language interpreter is embedded in SITE. The integration of sub models can be achieved via the scripting language or by usage of a generic interface provided by SITE. Furthermore, functionalities important for land-use modeling like model calibration, model tests and analysis support of simulation results have been integrated into the generic framework. During the implementation of SITE, specific emphasis was laid on expandability, maintainability and usability. Along with the modeling framework a land use model for the analysis of the stability of tropical rainforest margins was developed in the context of the collaborative research project STORMA (SFB 552). In a research area in Central Sulawesi, Indonesia, socio-environmental impacts of land-use changes were examined. SITE was used to simulate land-use dynamics in the historical period of 1981 to 2002. Analogous to that, a scenario that did not consider migration in the population dynamics, was analyzed. For the calculation of crop yields and trace gas emissions, the DAYCENT agro-ecosystem model was integrated. In this case study, it could be shown that land-use changes in the Indonesian research area could mainly be characterized by the expansion of agricultural areas at the expense of natural forest. For this reason, the situation had to be interpreted as unsustainable even though increased agricultural use implied economic improvements and higher farmers' incomes. Due to the importance of model calibration, it was explicitly addressed in the SITE architecture through the introduction of a specific component. The calibration functionality can be used by all SITE applications and enables largely automated model calibration. Calibration in SITE is understood as a process that finds an optimal or at least adequate solution for a set of arbitrarily selectable model parameters with respect to an objective function. In SITE, an objective function typically is a map comparison algorithm capable of comparing a simulation result to a reference map. Several map optimization and map comparison methodologies are available and can be combined. The STORMA land-use model was calibrated using a genetic algorithm for optimization and the figure of merit map comparison measure as objective function. The time period for the calibration ranged from 1981 to 2002. For this period, respective reference land-use maps were compiled. It could be shown, that an efficient automated model calibration with SITE is possible. Nevertheless, the selection of the calibration parameters required detailed knowledge about the underlying land-use model and cannot be automated. In another case study decreases in crop yields and resulting losses in income from coffee cultivation were analyzed and quantified under the assumption of four different deforestation scenarios. For this task, an empirical model, describing the dependence of bee pollination and resulting coffee fruit set from the distance to the closest natural forest, was integrated. Land-use simulations showed, that depending on the magnitude and location of ongoing forest conversion, pollination services are expected to decline continuously. This results in a reduction of coffee yields of up to 18% and a loss of net revenues per hectare of up to 14%. However, the study also showed that ecological and economic values can be preserved if patches of natural vegetation are conservated in the agricultural landscape. -----------------------------------------------------------------------

Productivity and optimum plant density of pigeonpea in different environments in Tanzania

The objective of the present study was to determine the optimum plant density of four pigeonpea genotypes, representing early, medium and late maturing types, grown in five contrasting environments in Tanzania. ICPL 86005 (early), Kat 50/3 and QP 37 (medium) and Local (late) were grown at four plant densities (40 000-320 000 plants/ha) in irrigated and rainfed conditions at Ilonga and under rainfed conditions at Kibaha, Selian and Ismani. At maturity, total above-ground biomass and seed yield (SY) were measured. The highest yields were obtained in the irrigated experiment at Ilonga, where the medium/late genotypes produced 25 t biomass/ha and 5 center dot 6 t seed/ha. The lowest SY were at Kibaha, 0 58 to 1 center dot 76 t/ha, where a severe drought occurred. In nearly all cases the response to density was linear or asymptotic. The response of ICPL 86005 was significantly different from the other three genotypes. The optimum density for SY varied from 37 000 to 227 000 plants/ha in ICPL 86005, compared with 3000 to 101000 plants/ha in the medium/late genotypes. The highest optimum density was at Selian and Ismani and the lowest at Ilonga and Kibaha, where drought occurred. Optimum densities therefore varied greatly with genotype (duration) and environment, and this variation needs to be considered when planning trials.

A low cost one-camera optical tracking system for indoor wide-area augmented and virtual reality environments

In the last years the number of industrial applications for Augmented Reality (AR) and Virtual Reality (VR) environments has significantly increased. Optical tracking systems are an important component of AR/VR environments. In this work, a low cost optical tracking system with adequate attributes for professional use is proposed. The system works in infrared spectral region to reduce optical noise. A highspeed camera, equipped with daylight blocking filter and infrared flash strobes, transfers uncompressed grayscale images to a regular PC, where image pre-processing software and the PTrack tracking algorithm recognize a set of retro-reflective markers and extract its 3D position and orientation. Included in this work is a comprehensive research on image pre-processing and tracking algorithms. A testbed was built to perform accuracy and precision tests. Results show that the system reaches accuracy and precision levels slightly worse than but still comparable to professional systems. Due to its modularity, the system can be expanded by using several one-camera tracking modules linked by a sensor fusion algorithm, in order to obtain a larger working range. A setup with two modules was built and tested, resulting in performance similar to the stand-alone configuration.

Structural reforms, productivity and technological change in Latin America

Includes bibliography

Leaf spray fertilization of boron and zinc on productivity and fruit quality of Japanese pear tree

The cultivation of fruit plants from temperate climate in tropical or subtropical regions can be a good income alternative for the producer. However, due to the little existent information about cultivation of those fruit plants, the producers use imported techniques of other producing areas, or even an association of practices used for other fruit plants, pointing out the leaf spray fertilization of micronutrients without appropriate scientific base. In this context, the objective of this study was to verify the effect of the leaf spray fertilization of B and Zn on productivity and fruit quality of Japanese pear tree. The experiment was conducted from 2004 to 2005, in Ilha Solteira, in northwestern São Paulo State-Brazil. The climate is, according to the Köpppen Classification, tropical wet and dry (Aw). The 'Okusankichi' cultivar, grafted on Pyrus communis L. rootstock was used as well as doses of 110 g.ha-1 of B and 250 g.ha-1 of Zn in each application. The treatments were: T1. water, T2. boric acid, T3. zinc sulfate, T4. T2 + T3, T5. boric acid + urea + citric acid + EDTA, T6. zinc sulfate + urea + citric acid + EDTA, T7. T5 + T6, T8. boric acid + urea + citric acid + EDTA + sodium molibdate + sulfur + calcium chloride, T9. zinc sulfate + urea + citric acid + EDTA + Fe sulfate + Mn sulfate + Mg sulfate and, T10. T8+T9. A randomized blocks design was used and the averages were compared by Tukey test. In the first crop the mixture of boric acid with quelating agents were efficient to supply B to the plants and zinc sulfate plus quelating agents were efficient to increase Zn leaf content. However, the productivity and the fruit quality were not influenced by the leaf spray of B and Zn. In the second crop the leaf content of B and Zn and the productivity were not influenced by the leaf spray; the boric acid and the zinc sulfate with or without quelating agents increased the contents of total soluble solids and, the boric acid with or without quelating agents increased the contents of total titratable acidity.

Intensive Rotational Grazing of Steers on Highly Erodible Land at the Adams County CRP Project, 2001

A steer grazing demonstration was conducted in 2001 at the CRP Research and Demonstration Project farm near Corning, Iowa. Ninety-five steers were delivered to the Adams County CRP farm on April 27, 2001. The steer pasture at the CRP farm was 76 acres, divided into 33 paddocks with electric fence. Cattle were moved 101 times to a fresh paddock during the grazing season. Most of the moves (79.2%) followed 1 day of grazing in a paddock. No paddock was grazed for more than 3 days in succession. Rate of gain on pasture (2.12 lbs./animal/day) was higher in 2001 than in any previous year in the 8-year steer grazing project at the CRP farm. The 95 steers gained a total of 21,056 pounds on pasture, and the cost of the gain on pasture was $51.30/cwt. The 2001 steer grazing project showed a small profit above all costs. The net profit was $4.12/steer or $5.15/acre. Large profits and large losses are possible, primarily depending on the difference between the buying and selling prices.

Design, Technology and Characterization of Micromechanised Sensors and Actuators for Harsh Environments

Los sistemas micro electro mecánicos (MEMS) han demostrado ser una exitosa familia de dispositivos que pueden usarse como plataforma para el desarrollo de dispositivos con aplicaciones en óptica, comunicaciones, procesado de señal y sensorización. Los dispositivos MEMS estándar suelen estar fabricados usando tecnología de silicio. Sin embargo, el rendimiento de estos MEMS se puede mejorar si se usan otros materiales. Por ejemplo, el diamante nanocristalino (NCD) ofrece unas excelentes propiedades mecánicas, transparencia y una superficie fácil de funcionalizar. Por otro lado, el sistema de materiales (In; Ga; Al)N, los materiales IIIN, se pueden usar para producir estructuras monocristalinas con alta sensibilidad mecánica y química. Además, el AlN se puede depositar por pulverización catódica reactiva sobre varios substratos, incluyendo NCD, para formar capas policristalinas orientadas con alta respuesta piezoeléctrica. Adicionalmente, tanto el NCD como los materiales III-N muestran una gran estabilidad térmica y química, lo que los hace una elección idónea para desarrollar dispositivos para aplicaciones para alta temperatura, ambientes agresivos e incluso para aplicaciones biocompatibles. En esta tesis se han usado estos materiales para el diseño y medición de demostradores tecnológicos. Se han perseguido tres objetivos principales: _ Desarrollo de unos procesos de fabricación apropiados. _ Medición de las propiedades mecánicas de los materiales y de los factores que limitan el rendimiento de los dispositivos. _ Usar los datos medidos para desarrollar dispositivos demostradores complejos. En la primera parte de esta tesis se han estudiado varias técnicas de fabricación. La estabilidad de estos materiales impide el ataque y dificulta la producción de estructuras suspendidas. Los primeros capítulos de esta disertación se dedican al desarrollo de unos procesos de transferencia de patrones por ataque seco y a la optimización del ataque húmedo sacrificial de varios substratos propuestos. Los resultados de los procedimientos de ataque se presentan y se describe la optimización de las técnicas para la fabricación de estructuras suspendidas de NCD y materiales III-N. En un capítulo posterior se estudia el crecimiento de AlN por pulverización catódica. Como se ha calculado en esta disertación para obtener una actuación eficiente de MEMS, las capas de AlN han de ser finas, típicamente d < 200 nm, lo que supone serias dificultades para la obtención de capas orientadas con respuesta piezoeléctrica. Las condiciones de depósito se han mapeado para identificar las fronteras que proporcionan el crecimiento de material orientado desde los primeros pasos del proceso. Además, durante la optimización de los procesos de ataque se estudió un procedimiento para fabricar películas de GaN nanoporoso. Estas capas porosas pueden servir como capas sacrificiales para la fabricación de estructuras suspendidas de GaN con baja tensión residual o como capas para mejorar la funcionalización superficial de sensores químicos o biológicos. El proceso de inducción de poros se discutirá y también se presentarán experimentos de ataque y funcionalización. En segundo lugar, se han determinado las propiedades mecánicas del NCD y de los materiales III-N. Se han fabricado varias estructuras suspendidas para la medición del módulo de Young y de la tensión residual. Además, las estructuras de NCD se midieron en resonancia para calcular el rendimiento de los dispositivos en términos de frecuencia y factor de calidad. Se identificaron los factores intrínsecos y extrínsecos que limitan ambas figuras de mérito y se han desarrollado modelos para considerar estas imperfecciones en las etapas de diseño de los dispositivos. Por otra parte, los materiales III-N normalmente presentan grandes gradientes de deformación residual que causan la deformación de las estructuras al ser liberadas. Se han medido y modelado estos efectos para los tres materiales binarios del sistema para proporcionar puntos de interpolación que permitan predecir las características de las aleaciones del sistema III-N. Por último, los datos recabados se han usado para desarrollar modelos analíticos y numéricos para el diseño de varios dispositivos. Se han estudiado las propiedades de transducción y se proporcionan topologías optimizadas. En el último capítulo de esta disertación se presentan diseños optimizados de los siguientes dispositivos: _ Traviesas y voladizos de AlN=NCD con actuación piezoeléctrica aplicados a nanoconmutadores de RF para señales de alta potencia. _ Membranas circulares de AlN=NCD con actuación piezoeléctrica aplicadas a lentes sintonizables. _ Filtros ópticos Fabry-Pérot basados en cavidades aéreas y membranas de GaN actuadas electrostáticamente. En resumen, se han desarrollado unos nuevos procedimientos optimizados para la fabricación de estructuras de NCD y materiales III-N. Estas técnicas se han usado para producir estructuras que llevaron a la determinación de las principales propiedades mecánicas y de los parámetros de los dispositivos necesarios para el diseño de MEMS. Finalmente, los datos obtenidos se han usado para el diseño optimizado de varios dispositivos demostradores. ABSTRACT Micro Electro Mechanical Systems (MEMS) have proven to be a successful family of devices that can be used as a platform for the development of devices with applications in optics, communications, signal processing and sensorics. Standard MEMS devices are usually fabricated using silicon based materials. However, the performance of these MEMS can be improved if other material systems are used. For instance, nanocrystalline diamond (NCD) offers excellent mechanical properties, optical transparency and ease of surface functionalization. On the other hand, the (In; Ga; Al)N material system, the III-N materials, can be used to produce single crystal structures with high mechanical and chemical sensitivity. Also, AlN can be deposited by reactive sputtering on various substrates, including NCD, to form oriented polycrystalline layers with high piezoelectric response. In addition, both NCD and III-N materials exhibit high thermal and chemical stability, which makes these material the perfect choice for the development of devices for high temperatures, harsh environments and even biocompatible applications. In this thesis these materials have been used for the design and measurement of technological demonstrators. Three main objectives have been pursued: _ Development of suitable fabrication processes. _ Measurement of the material mechanical properties and device performance limiting factors. _ Use the gathered data to design complex demonstrator devices. In a first part of the thesis several fabrication processes have been addressed. The stability of these materials hinders the etching of the layers and hampers the production of free standing structures. The first chapters of this dissertation are devoted to the development of a dry patterning etching process and to sacrificial etching optimization of several proposed substrates. The results of the etching processes are presented and the optimization of the technique for the manufacturing of NCD and III-N free standing structures is described. In a later chapter, sputtering growth of thin AlN layers is studied. As calculated in this dissertation, for efficient MEMS piezoelectric actuation the AlN layers have to be very thin, typically d < 200 nm, which poses serious difficulties to the production of c-axis oriented material with piezoelectric response. The deposition conditions have been mapped in order to identify the boundaries that give rise to the growth of c-axis oriented material from the first deposition stages. Additionally, during the etching optimization a procedure for fabricating nanoporous GaN layers was also studied. Such porous layers can serve as a sacrificial layer for the release of low stressed GaN devices or as a functionalization enhancement layer for chemical and biological sensors. The pore induction process will be discussed and etching and functionalization trials are presented. Secondly, the mechanical properties of NCD and III-N materials have been determined. Several free standing structures were fabricated for the measurement of the material Young’s modulus and residual stress. In addition, NCD structures were measured under resonance in order to calculate the device performance in terms of frequency and quality factor. Intrinsic and extrinsic limiting factors for both figures were identified and models have been developed in order to take into account these imperfections in the device design stages. On the other hand, III-N materials usually present large strain gradients that lead to device deformation after release. These effects have been measured and modeled for the three binary materials of the system in order to provide the interpolation points for predicting the behavior of the III-N alloys. Finally, the gathered data has been used for developing analytic and numeric models for the design of various devices. The transduction properties are studied and optimized topologies are provided. Optimized design of the following devices is presented at the last chapter of this dissertation: _ AlN=NCD piezoelectrically actuated beams applied to RF nanoswitches for large power signals. _ AlN=NCD piezoelectrically actuated circular membranes applied to tunable lenses. _ GaN based air gap tunable optical Fabry-Pérot filters with electrostatic actuation. On the whole, new optimized fabrication processes has been developed for the fabrication of NCD and III-N MEMS structures. These processing techniques was used to produce structures that led to the determination of the main mechanical properties and device parameters needed for MEMS design. Lastly, the gathered data was used for the design of various optimized demonstrator devices.

Project Skywater; proceedings: Skywater Conference II: design and evaluation of weather modification experiments.

On t.p.: "Atmospheric water resources program."

A comparative assessment of performance and productivity of health centres in Seychelles

Purpose - The purpose of this paper is to measure the technical and scale efficiency of health centres; to evaluate changes in productivity; and to highlight possible policy implications of the results for policy makers. Design/methodology/approach - Data envelopment analysis (DEA) is employed to assess the technical and scale efficiency, and productivity change over a four-year period among 17 public health centres. Findings - During the period of study, the results suggest that the public health centres in Seychelles have exhibited mean overall or technical efficiency of above 93 per cent. It was also found that the overall productivity increased by 2.4 per cent over 2001-2004. Research limitations/implications - Further research can be undertaken to gather data on the prices of the various inputs to facilitate an estimation of the allocative efficiency of clinics. If such an exercise were to be undertaken, researchers may also consider collecting data on quantities and prices of paramedical, administrative and support staff to ensure that the analysis is more comprehensive than the study reported in this paper. Institutionalization of efficiency monitoring would help to enhance further the already good health sector stewardship and governance. Originality/value - This paper provides new empirical evidence on a four-year trend in the efficiency and productivity of health centres in Seychelles. © Emerald Group Publishing Limited.