Use of axially graded burnable boron for hot-spot temperature reduction in a pressurized water reactor core

Shortly after the loading of a pressurized water reactor (PWR) core, the axial power distribution in fresh fuel has already attained the characteristic, almost flat shape, typical of burned fuel. At beginning of cycle (BOC), however, the axial distribution is centrally peaked. In assemblies hosting uniform burnable boron rods, this BOC peaking is even more pronounced. A reduction in the axial peaking is today often achieved by shortening the burnable boron rods by some 30 cm at each edge. It is shown that a two-zone grading of the boron rod leads, in a representative PWR cycle, to a reduction of the hot-spot temperature of approximately 70 °C, compared with the nongraded case. However, with a proper three-zone grading of the boron rod, an additional 20 °C may be cut off the hot-spot temperature. Further, with a slightly skewed application of this three-zone grading, an additional 50 °C may be cut off. The representative PWR cycle studied was cycle 11 of the Indian Point 2 station, with a simplification in the number of fuel types and in the burnup distribution. The analysis was based on a complete three-dimensional burnup calculation. The code system was ELCOS, with BOXER as an assembly code for the generation of burnup-dependent cross sections and SILWER as a three-dimensional core code with thermal-hydraulic feedback.

Application of axial discontinuity factors for high conversion water reactors

The paper shows that generating cross sections using three-dimensional geometry and application of axial discontinuity factors are essential requirements for obtaining accurate prediction of criticality and zone average reaction rates in highly heterogeneous RBWR-type systems using computer codes based on diffusion theory approximation. The same methodology as presented here will be used to generate discontinuity factors for each axial interface between fuel assembly zones to ensure preservation of reaction rates in each zone and global multiplication factor. The use of discontinuity factors and three-dimensional cross sections may allow for a coarser energy group structure which is desirable to simplify and speed up transient calculations.

Thorium fuel cycles for light water reactors: homogeneous design

The proliferation potential of the present light water reactor (LWR) fuel cycle is related primarily to the quantity and the quality of the residual Pu contained in the spent-fuel stockpile, although other potentially “weapons usable” materials are also a concern. Thorium-based nuclear fuel produces much smaller amounts of Pu in comparison with standard LWR fuel, and consequently, it is more proliferation resistant than conventional slightly enriched all-U fuel; the long-term toxicity of the spent-fuel stockpile is also reduced

Potential issues related to emergency core cooling system strainers performance at boiling water reactors: application to Cofrentes NPP (Spain)

From the 60s to the 90s, a great number of events related to the Emergency Core Cooling Systems Strainers have been happened in all kind of reactors all over the world. Thus, the Nuclear Regulatory Commission of the USA emitted some Bulletins to address the concerns about the adequacy of Emergency Core Cooling Systems (ECCS) strainer performance at boiling water reactors (BWR). In Spain the regulatory body (Consejo de Seguridad Nuclear, CSN) adopted the USA regulation and Cofrentes NPP installed new strainers with a considerable bigger size than the old strainers. The nuclear industry conducted significant and extensive research, guidance development, testing, reviews, and hardware and procedure changes during the 90s to resolve the issues related to debris blockage of BWR strainers. In 2001 the NRC and CSN closed the Bulletins. Thereafter, the strainers issues were moved to the PWR reactors. In 2004 the NRC issued a Generic Letter (GL). It requested the resolution of several effects which were not noted in the past. The GL regarded to be resolved by the PWR reactors but the NRC in USA and the CSN in Spain have requested that the BWR reactors investigate differences between the methodologies used by the BWRs and PWRs. The developments and improvements done for Cofrentes NPP are detailed. Studies for this plant show that the head loss due to the considered debris is at most half of the limited head loss for the ECCS strainer and the NPSH (Net Positive Suction Head) required for the ECCS pumps is at least three times lower than the NPSH available.

Boiling water reactors : an annotated bibliography of selected literature /

"June 1959."

Zirconium-water reactions /

Reproduced by NTIS.

Kinetic studies of heterogeneous water reactors : Annual summary report - 1959.

Prepared under Contract AT(04-3)-165 for the U.S. Atomic Energy Commission, San Francisco Operations Office.

Kinetic studies of heterogeneous water reactors : Annual summary report - 1960.

Prepared under Contract AT(04-3)-165 for the U.S. Atomic Energy Commission, San Francisco Operations Office.

Proceedings of the U.S. Nuclear Regulatory Commission Thirteenth Water Reactor Safety Research Information Meeting, held at National Bureau of Standards, Gaithersburg, Maryland, October 22-25, 1985 /

Includes bibliographies.

Nuclear powerplant standardization : light water reactors.

"April 1981" (v. 1); "June 1981" (v. 2)

CFD-modeling and experiments of insulation debris transport phenomena in water flow

The investigation of insulation debris generation, transport, and sedimentation becomes more important with regard to reactor safety research for pressurized water reactors and boiling water reactors when considering the long-term behavior of emergency core coolant systems during all types of loss-of-coolant accidents (LOCAs). The insulation debris released near the break during a LOCA incident consists of a mixture of disparate particle populations that varies with size, shape, consistency, and other properties. Some fractions of the released insulation debris can be transported into the reactor sump, where it may perturb/impinge on the emergency core cooling systems. Open questions of generic interest are, for example, the particle load on strainers and corresponding pressure drop, the sedimentation of the insulation debris in a water pool, and its possible resuspension and transport in the sump water flow. A joint research project on such questions is being performed in cooperation with the University of Applied Sciences Zittau/Görlitz. The project deals with the experimental investigation and the development of computational fluid dynamics (CFD) models for the description of particle transport phenomena in coolant flow. While the experiments are performed at the University of Applied Sciences Zittau/Görlitz, the theoretical work is concentrated at Forschungszentrum Dresden-Rossendorf. In the current paper the basic concepts for CFD modeling are described and feasibility studies including the conceptual design of the experiments are presented.