Managing Nile perch using slot size: is it possible?

The fishery of Lake Victoria became a major commercial fishery with the introduction of Nile perch in 1950s and 1960s. Biological and population characteristics point to a fishery under intense fishing pressure attributed to increased capacity and use of illegal fishing gears. Studies conducted between 1998 to 2000 suggested capture of fish between slot size of 50 to 85 cm TL to sustain the fishery. Samples from Kenya and Uganda factories in 2008 showed that 50% and 71% of individuals processed were below the slot size respectively. This study revealed that fish below and above the slot has continued being caught and processed. This confirms that the slot size is hardly adhered to by both the fishers and the processors. The paper explores why the slot size has not been a successful tool in management of Nile perch and suggests strategies to sustain the fishery

A novel ultra-fast optical router using time-slot switching

We present a novel optical routing scheme scalable to greater than 50×50 channels with a potential aggregate bit-rate of 1Tbps. The proof-of-principle experiment demonstrates the feasibility of the router with a de-multiplexed Q-factor of 6.35. © 2004 Optical Society of America.

Enhanced light emission in active silicon-on-insulator photonic crystal slabs and slot waveguides

We present experimental measurements on Silicon-on-insulator (SOI) photonic crystal slabs with an active layer containing Er3+ ions-doped Silicon nanoclusters (Si-nc), showing strong enhancement of 1.54 μm emission at room temperature. We provide a systematic theoretical analysis to interpret such results. In order to get further insight, we discuss experimental data on the guided luminescence of unpatterned SOI planar slot waveguides, which show enhanced light emission in transverse-magnetic (TM) modes over transverse-electric (TE) ones. ©2007 IEEE.

Modelling and analysis of modal behaviour in SOI slot waveguides

Mode behaviour for SOI slot waveguides is modelled and analysed using a numerical full vectorial method based on the film mode matching method (MMM). Only the quasi-TE mode is investigated. Waveguide heights and slot widths, as well as silicon widths are properly chosen with respect to the single mode behaviour in the slot region. Comparison between the effective index method and our side loss method shows that our single mode condition is creditable. The optical power confinement in slot region for the quasi-TE mode is also studied and presented. We demonstrate that the maximum achievable optical power confinement P-slot and the maximum normalized average optical intensity I-slot are 42% and 26 mu m(-2), respectively.

Simulation demonstration and experimental fabrication of a multiple-slot waveguide

A multiple-slot waveguide is presented and demonstrated through theoretical simulation. Taking a double-slot waveguide as an example, the results show a nearly 30% enhancement of optical intensity compared with the traditional single-slot waveguide with the same slot gap width. Therefore, the E-field intensity of the slot can be increased by adding another smaller slot. A double-slot waveguide with oxide and air as low index slot materials is realized experimentally and the formation processes of the slots are analyzed.

High efficiency fiber to waveguide optical coupler in silicon-on-insulator-based slot waveguides - art. no. 68310R

We propose a novel optical fiber-to-waveguide coupler for integrated optical circuits. The proper materials and structural parameters of the coupler, which is based on a slot waveguide, are carefully analyzed using a full-vectorial three dimensional mode solver. Because the effective refractive index of the mode in a silicon-on-insulator-based slot waveguide can be extremely close to that of the fiber, a highly efficient fiber-to-waveguide coupling application can be realized. For a TE-like mode, the calculated minimum mismatch loss is about 1.8dB at 1550nm, and the mode conversion loss can be less than 0.5dB. The discussion of the present state-of-the-art is also involved. The proposed coupler can be used in chip-to-chip communication.

A Geometric Approach to Slot Alignment in Wireless Sensor Networks

Traditionally, slotted communication protocols have employed guard times to delineate and align slots. These guard times may expand the slot duration significantly, especially when clocks are allowed to drift for longer time to reduce clock synchronization overhead. Recently, a new class of lightweight protocols for statistical estimation in wireless sensor networks have been proposed. This new class requires very short transmission durations (jam signals), thus the traditional approach of using guard times would impose significant overhead. We propose a new, more efficient algorithm to align slots. Based on geometrical properties of space, we prove that our approach bounds the slot duration by only a constant factor of what is needed. Furthermore, we show by simulation that this bound is loose and an even smaller slot duration is required, making our approach even more efficient.