Electrical switching studies on the thin films of polyfuran and polyacrylonitrile prepared by plasma polymerisation and vacuum evaporated amorphous silicon

This thesis Entitled Electrical switching studies on the thin flims of polyfuran and polyacrylonitrile prepared by plasma polymerisation and vacuum evaporated amorphous silicon.A general introduction to the switching and allied phenomena is presented. Subsequently, developments of switching in thin films are described. The Mott transition is qualitatively presented. The working of a switching transitor is outlined and compared to the switching observed in thin films. Characteristic parameters of switching such as threshold voltage, time response to a, voltage pulse, and delay time are described. The various switching configurations commonly used are discussed. The mechanisms used to explain the switching behaviour like thermal, electrothermal and purely electronic are reviewed. Finally the scope, feasibility and the importance of polymer thin films in switching are highlighted.

Formation And Electrical Properties Of Polyacrylonitrile Thin Films Prepared By Plasma - Polymerisation

Due to the great versatility of the properties of polymer thin films, special interest has been taken in recent years on their preparation and electrical properties. The present thesis is entirely devoted to the study of the formation, structure and electrical properties of plasma» polymerised polyacrylonitrile (PAN) thin films. Eventhough the studies are confined to a single polymer film, the results in general are applicable to similar polar polymer films.

Microfabrication of high-performance aromatic polymers as nanotubes or fibrils by in situ ring-opening polymerisation of macrocyclic precursors

Melt-phase nucleophilic ring-opening polymerisation of macrocyclic aromatic ethers and thioethers at high temperatures within the cylindrical pores of an anodic-alumina membrane, followed by dissolution of the template, enables replication of the membrane's internal pore structure and so affords high-performance aromatic polymers with well-defined fibrillar or tubular morphologies.

Correlation between regioselectivity and site charge in propene polymerisation catalysed by metallocene

The reactions of propene with [Zr(cyclopentadienyl)(2)Me](+) have been investigated using density functional theory in order to study the correlation between regioselectivity and site charge in propene polymerisation. The reaction paths of the 1,2 and 2,1 additions of the methyl group to propene have been established. The geometries and energies of the reactants, transition states and products have been obtained using both PBEPBE/LANL2DZ and B3LYP/LANL2DZ methodologies. The results with both density functionals show that the activation energy for 1,2-insertion is lower than that for 2,1-insertion (Fig. 5) and this is consistent with the experiment results. Also for both density functionals, the difference of the thermal dynamic driving forces between the 2,1 product named 2-21 and the 1,2 product named 2-12 is significantly lower than the difference between the energy barriers. It is noted that in the reactants, the Mulliken partial charge on the central carbon atom C2 is positive and it can be concluded that 1,2-insertion is favoured because it can proceed via a cationic reaction.

A novel study of the polymerisation process involved in the formation of the network component of polymer-stabilised liquid crystals within electro-optic cells using high performance liquid chromatography

Polymer-stabilised liquid crystals are systems in which a small amount of monomer is dissolved within a liquid crystalline host, and then polymerised in situ to produce a network. The progress of the polymerisation, performed within electro-optic cells, was studied by establishing an analytical method novel to these systems. Samples were prepared by photopolymerisation of the monomer under well-defined reaction conditions; subsequent immersion in acetone caused the host and any unreacted monomer to dissolve. High performance liquid chromatography was used to separate and detect the various solutes in the resulting solutions, enabling the amount of unreacted monomer for a given set of conditions to be quantified. Longer irradiations cause a decrease in the proportion of unreacted monomer since more network is formed, while a more uniform LC director alignment (achieved by decreasing the sample thickness) or a higher level of order (achieved by decreasing the polymerisation temperature) promotes faster reactions.

Synthesis and polymerisation of α,ω-bis(3-pyrrolyl)alkanes

The synthesis, characterisation and polymerisation studies of a homologous series of α,ω-bis(pyrrolyl)alkanes are described. These α,ω-bis(pyrrolyl)alkanes were produced using Friedel–Crafts acylation followed by reduction of the carbonyl group using Red-Al®. Chemical polymerisation of the resultant dimers using FeCl₃ produced poly(α,ω-bis(pyrrolyl)alkane) films, which were characterised by SEM, FTIR and tested for conductivity.

Robust, electro-conductive, self-healing superamphiphobic fabric prepared by one-step vapour-phase polymerisation of poly(3,4-ethylenedioxythiophene) in the presence of fluorinated decyl polyhedral oligomeric silsesquioxane and fluorinated alkyl silane

A robust, electrically conductive, superamphiphobic fabric was prepared by vapour-phase polymerisation of 3,4-ethylenedioxythiophene (EDOT) on fabric in the presence of fluorinated decyl polyhedral oligomeric silsesquioxane (FD-POSS) and a fluorinated alkyl silane (FAS). The coated fabric had contact angles of 169° and 156° respectively to water and hexadecane, and a surface resistance in the range of 0.8–1.2 kΩ o⁻¹ . The incorporation of FD-POSS and FAS into the PEDOT layer showed a very small influence on the conductivity but improved the washing and abrasion stability considerably. The coated fabric can withstand at least 500 cycles of standard laundry and 10000 cycles of abrasion without apparently changing the superamphiphobicity, while the conductivity only had a small reduction after the washing and abrasion. More interestingly, the coating had a self-healing ability to auto-repair from chemical damages to restore the liquid repellency.