984 resultados para Point-Contact


Relevância:

60.00% 60.00%

Publicador:

Resumo:

This work reports on the synthesis of chromium oxide thin films prepared by photodissociation of Cr(CO)(6) in an oxidizing atmosphere, using a pulsed UV laser (KrF, lambda = 248 nm). The experimental conditions, which should enable the synthesis of CrO2, are discussed and results on the deposition of CrxOy films on Al2O3 (0001) substrates are presented.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

This work reports on the synthesis of chromium (III, IV) oxides films by KrF laser-assisted CVD. Films were deposited onto sapphire substrates at room temperature by the photodissociation of Cr(CO)(6) in dynamic atmospheres containing oxygen and argon. A study of the processing parameters has shown that partial pressure ratio Of O-2 to Cr(CO)(6) and laser fluence are the prominent parameters that have to be accurately controlled in order to co-deposit both the crystalline oxide phases. Films consistent with such a two-phase system were synthesised for a laser fluence of 75 mJ cm(-2) and a partial pressure ratio of about 1. (c) 2005 Elsevier B.V. All rights reserved.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

A serial-link manipulator may form a mobile closed kinematic chain when interacting with the environment, if it is redundant with respect to the task degrees of freedom (DOFs) at the endpoint. If the mobile closed chain assumes a number of configurations, then loop consistency equations permit the manipulator and task kinematics to be calibrated simultaneously using only the joint angle readings; endpoint sensing is not required. Example tasks include a fixed endpoint (0 DOF task), the opening of a door (1 DOF task), and point contact (3 DOF task). Identifiability conditions are derived for these various tasks.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

We report 18 new laser lines from (CH3OH)-C-13 generated in an optically pumped far-infrared laser; the laser lines are in the range of 54.2-420 mu m and are all characterized in wavelength, polarization relative to the pumping CO2 radiation, and pump offset relative to the CO2 center frequency, the frequencies of seven of these new lines along with 10 previously reported lines were measured by an accurate heterodyne technique, mixing them in a metal-insulator-metal (MIM) point contact diode, with another laser line of known frequency.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

O estudo do comportamento dinâmico da junção que se forma ao se unir uma fibra nervosa a um semicondutor é objeto de muitas pesquisas ultimamente em grandes centros de pesquisas. Estes estudos levam basicamente a dois modelos matemáticos de modelagem da junção: o modelo de contacto de ponta e o modelo de contacto de área. Utilizando o modelo de contacto de área, resolve-se a equação diferencial que descreve o comportamento dinâmico da junção neurônio-semicondutor, através de dois métodos analíticos. No primeiro método a solução da equação diferencial é obtida através da soma de duas equações: da solução da equação homogênea mais a da equação particular, obtendo dessa forma, o resultado que consta na literatura. Já o segundo método é o que descreve a solução usando as funções de Green, cujo resultado, embora não coincidente com o da literatura, é totalmente coincidente na região de interesse dentro da junção. A vantagem do uso da função de Green na determinação da solução de uma equação diferencial, é que, uma vez determinada essa função, a solução dessa equação diferencial é obtida de forma imediata, bastando para tal, fazer um processo de integração do produto entre a função de Green e a função de excitação ou fonte. Por último, mostra-se a completa equivalência entre os dois métodos de soluções da equação diferencial.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

We report the frequency measurements of 18 optically pumped far-infrared (FIR) laser lines generated from CD3OH and (CH3OH)-C-13. We use the heterodyne technique of mixing FIR laser radiations and microwave radiation on a metal-insulator-metal point-contact tunnel diode to determine the FIR laser frequencies. Two FIR laser systems, consisting of CO2 waveguide pump lasers and Fabry-Perot FIR laser cavities, were used as optical sources. (C) 1997 Optical Society of America.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

Die Verbindung von elektrisch aktiven, lebenden Zellen zu extrazellulären Sensorsystemen eröffnet vielfälige Möglichkeiten im Bereich der Biosensorik. Die vorliegende Arbeit leistet einen Beitrag zum tieferen Verständnis der elektrischen Kopplungsmechanismen zwischen den biologischen und elektronischen Teilen solcher Hybridsysteme. Es wurden dazu drei Hauptbereiche bearbeitet:Ein System zur extrazellulären Signalableitung an lebenden Zellen bestehend aus einem Sensorchip, einem Vorverstärkerkopf und einem Hauptverstärker wurde weiterentwickelt.Als Sensoren wurden entweder Metallmikroelektroden-Chips mit 64 Kanälen oder Feldeffekt Transistoren-Chips mit 16 Kanälen (FET) eingesetzt. Es wurden zusätzlich spezielle FET Sensoren mit Rückseitenkontakten hergestellt und eingesetzt.Die elektrische Kopplung von einzelnen Nervenzellen der neuronalen Zell-Linien SH-SY5Y und TR14 oder primär kultivierten Neuronen aus dem Hirnstamm oder dem Hippocampus von embryonalen Ratten mit den extrazellulären Sensoren wurde untersucht. In der 'whole-cell' Patch-Clamp Technik wurden die Beiträge der spannungsgesteuerten Na+- und K+-Ionenkanäle zur extrazellulären Signalform identifiziert. Die Simulation der Signale mit einem Ersatzschaltkreis (Punkt-Kontakt Modell), der in PSPICE implementiert wurde, deutet auf eine starke Abhängigkeit der Signalformen in bezug auf Konzentrationsänderungen von Na+- und K+-Ionen im Volumenbereich zwischen Zelle und den ionensensitiven Transistoren hin. Ein empirisch erweitertes Punkt-Kontakt Modell wurde daraufhin vorgestellt.Im dritten Teil der Arbeit wurden Zellschichten von Kardiomyocyten embryonaler Ratten auf den extrazellulären Sensoren kultiviert. Die Eignung eines solchen Hybridsensors als Modellherz fuer das pharmazeutische Screeing wurde durch Messungen mit Herzstimulanzien und -relaktanzien bestätigt.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

Due to its high Curie temperature of 420K and band structure calculations predicting 100% spin polarisation, Sr2FeMoO6 is a potential candidate for spintronic devices. However, the preparation of good quality thin films has proven to be a non-trivial task. Epitaxial Sr2FeMoO6 thin films were prepared by pulsed laser deposition on different substrates. Differing from previous reports a post-deposition annealing step at low oxygen partial pressure (10-5 mbar) was introduced and enabled the fabrication of reproducible, high quality samples. According to the structural properties of the substrates the crystal structure and morphology of the thin films are modified. The close interrelation between the structural, magnetic and electronic properties of Sr2FeMoO6 was studied. A detailed evaluation of the results allowed to extract valuable information on the microscopic nature of magnetism and charge transport. Smooth films with a mean roughness of about 2 nm have been achieved, which is a pre-requisite for a possible inclusion of this material in future devices. In order to establish device-oriented sub-micron patterning as a standard technique, electron beam lithography and focussed ion beam etching facilities have been put into operation. A detailed characterisation of these systems has been performed. To determine the technological prospects of new spintronics materials, the verification of a high spin polarisation is of vital interest. A popular technique for this task is point contact Andreev reflection (PCAR). Commonly, the charge transport in a transparent metal-superconductor contact of nanometer dimensions is attributed solely to coherent transport. If this condition is not fulfilled, inelastic processes in the constriction have to be considered. PCAR has been applied to Sr2FeMoO6 and the Heusler compound Co2Cr0.6Fe0.4Al. Systematic deviations between measured spectra and the standard models of PCAR have been observed. Therefore existing approaches have been generalised, in order to include the influence of heating. With the extended model the measured data was successfully reproduced but the analysis has revealed grave implications for the determination of spin polarisation, which was found to break down completely in certain cases.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

Photovoltaic (PV) conversion is the direct production of electrical energy from sun without involving the emission of polluting substances. In order to be competitive with other energy sources, cost of the PV technology must be reduced ensuring adequate conversion efficiencies. These goals have motivated the interest of researchers in investigating advanced designs of crystalline silicon solar (c-Si) cells. Since lowering the cost of PV devices involves the reduction of the volume of semiconductor, an effective light trapping strategy aimed at increasing the photon absorption is required. Modeling of solar cells by electro-optical numerical simulation is helpful to predict the performance of future generations devices exhibiting advanced light-trapping schemes and to provide new and more specific guidelines to industry. The approaches to optical simulation commonly adopted for c-Si solar cells may lead to inaccurate results in case of thin film and nano-stuctured solar cells. On the other hand, rigorous solvers of Maxwell equations are really cpu- and memory-intensive. Recently, in optical simulation of solar cells, the RCWA method has gained relevance, providing a good trade-off between accuracy and computational resources requirement. This thesis is a contribution to the numerical simulation of advanced silicon solar cells by means of a state-of-the-art numerical 2-D/3-D device simulator, that has been successfully applied to the simulation of selective emitter and the rear point contact solar cells, for which the multi-dimensionality of the transport model is required in order to properly account for all physical competing mechanisms. In the second part of the thesis, the optical problems is discussed. Two novel and computationally efficient RCWA implementations for 2-D simulation domains as well as a third RCWA for 3-D structures based on an eigenvalues calculation approach have been presented. The proposed simulators have been validated in terms of accuracy, numerical convergence, computation time and correctness of results.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

L'energia solare rientra nel gruppo delle energie rinnovabili, ovvero che provengono da una fonte il cui utilizzo attuale non ne pregiudica la disponibilità nel futuro. L'energia solare ha molti vantaggi, poiché è inesauribile ed è una risorsa d'immediata disponibilità perché giunge attraverso i raggi del sole. La conversione fotovoltaica sfrutta il meccanismo di generazione di carica elettrica prodotto dall'interazione della radiazione luminosa su di un materiale semiconduttore. La necessità di creare energia riducendo al minimo l'impatto ambientale ed il contemporaneo aumento del prezzo di fonti fossili come ad esempio il petrolio ed il carbone (senza trascurare il fatto che le riserve di essi sono, di fatto, esauribili) ha portato un aumento considerevole della produzione di energia elettrica tramite conversione fotovoltaica. Allo stato attuale dell'economia e dei mercati, sebbene il settore fotovoltaico sia in forte crescita, non è esente da un parametro che ne descrive le caratteristiche economiche ed energetiche, il cosiddetto rapporto costo/efficienza. Per efficienza, si intende la quantità di energia elettrica prodotta rispetto alla potenza solare incidente per irraggiamento, mentre per costo si intende quello sostenuto per la costruzione della cella. Ridurre il rapporto costo/efficienza equivale a cercare di ottenere un'efficienza maggiore mantenendo inalterati i costi, oppure raggiungere una medio-alta efficienza ma ridurre in maniera significativa la spesa di fabbricazione. Quindi, nasce la necessità di studiare e sviluppare tecnologie di celle solari all'avanguardia, che adottino accorgimenti tecnologici tali per cui, a parità di efficienza di conversione, il costo di produzione della cella sia il più basso possibile. L'efficienza dei dispositivi fotovoltaici è limitata da perdite ottiche, di ricombinazione di carica e da resistenze parassite che dipendono da diversi fattori, tra i quali, le proprietà ottiche e di trasporto di carica dei materiali, l'architettura della cella e la capacità di intrappolare la luce da parte del dispositivo. Per diminuire il costo della cella, la tecnologia fotovoltaica ha cercato di ridurre il volume di materiale utilizzato (in genere semiconduttore), dal momento in cui si ritiene che il 40% del costo di una cella solare sia rappresentato dal materiale. Il trend che questo approccio comporta è quello di spingersi sempre di più verso spessori sottili, come riportato dalla International Technology Roadmap for Photovoltaic, oppure ridurre il costo della materia prima o del processo. Tra le architetture avanzate di fabbricazione si analizzano le Passivated Emitter and Rear Cell-PERC e le Metal Wrap Through-MWT Cell, e si studia, attraverso simulazioni numeriche TCAD, come parametri geometrici e di drogaggio vadano ad influenzare le cosiddette figure di merito di una cella solare.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

A century after the discovery of superconductivity, the design of new and more useful superconductors remains enigmatic. High-temperature super-conductors offer unique solutions to fundamental grid challenges of the 21st century and hold great promise in addressing global energy challenges in energy production, storage, and distribution. Traditionally guided by serendipity, researchers now endeavor to design new superconductors predictively. Advanced experimental techniques, such as point contact spectroscopy measurements, aid in identifying promising candidates.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

La fisuración iniciada en la superficie de los pavimentos asfálticos constituye uno de los más frecuentes e importantes modos de deterioro que tienen lugar en los firmes bituminosos, como han demostrado los estudios teóricos y experimentales llevados a cabo en la última década. Sin embargo, este mecanismo de fallo no ha sido considerado por los métodos tradicionales de diseño de estos firmes. El concepto de firmes de larga duración se fundamenta en un adecuado seguimiento del proceso de avance en profundidad de estos deterioros y la intervención en el momento más apropiado para conseguir mantenerlos confinados como fisuras de profundidad parcial en la capa superficial más fácilmente accesible y reparable, de manera que pueda prolongarse la durabilidad y funcionalidad del firme y reducir los costes generalizados de su ciclo de vida. Por lo tanto, para la selección de la estrategia óptima de conservación de los firmes resulta esencial disponer de metodologías que posibiliten la identificación precisa in situ de la fisuración descendente, su seguimiento y control, y que además permitan una determinación fiable y con alto rendimiento de su profundidad y extensión. En esta Tesis Doctoral se presentan los resultados obtenidos mediante la investigación sistemática de laboratorio e in situ llevada a cabo para la obtención de datos sobre fisuración descendente en firmes asfálticos y para el estudio de procedimientos de evaluación de la profundidad de este tipo de fisuras empleando técnicas de ultrasonidos. Dichos resultados han permitido comprobar que la metodología no destructiva propuesta, de rápida ejecución, bajo coste y sencilla implementación (principalmente empleada hasta el momento en estructuras metálicas y de hormigón, debido a las dificultades que introduce la naturaleza viscoelástica de los materiales bituminosos) puede ser aplicada con suficiente fiabilidad y repetibilidad sobre firmes asfálticos. Las medidas resultan asimismo independientes del espesor total del firme. Además, permite resolver algunos de los inconvenientes frecuentes que presentan otros métodos de diagnóstico de las fisuras de pavimentos, tales como la extracción de testigos (sistema destructivo, de alto coste y prolongados tiempos de interrupción del tráfico) o algunas otras técnicas no destructivas como las basadas en medidas de deflexiones o el georradar, las cuales no resultan suficientemente precisas para la investigación de fisuras superficiales. Para ello se han realizado varias campañas de ensayos sobre probetas de laboratorio en las que se han estudiado diferentes condiciones empíricas como, por ejemplo, distintos tipos de mezclas bituminosas en caliente (AC, SMA y PA), espesores de firme y adherencias entre capas, temperaturas, texturas superficiales, materiales de relleno y agua en el interior de las grietas, posición de los sensores y un amplio rango de posibles profundidades de fisura. Los métodos empleados se basan en la realización de varias medidas de velocidad o de tiempo de transmisión del pulso ultrasónico sobre una única cara o superficie accesible del material, de manera que resulte posible obtener un coeficiente de transmisión de la señal (mediciones relativas o autocompensadas). Las mediciones se han realizado a bajas frecuencias de excitación mediante dos equipos de ultrasonidos diferentes dotados, en un caso, de transductores de contacto puntual seco (DPC) y siendo en el otro instrumento de contacto plano a través de un material especialmente seleccionado para el acoplamiento (CPC). Ello ha permitido superar algunos de los tradicionales inconvenientes que presenta el uso de los transductores convencionales y no precisar preparación previa de las superficies. La técnica de autocalibración empleada elimina los errores sistemáticos y la necesidad de una calibración local previa, demostrando el potencial de esta tecnología. Los resultados experimentales han sido comparados con modelos teóricos simplificados que simulan la propagación de las ondas ultrasónicas en estos materiales bituminosos fisurados, los cuales han sido deducidos previamente mediante un planteamiento analítico y han permitido la correcta interpretación de dichos datos empíricos. Posteriormente, estos modelos se han calibrado mediante los resultados de laboratorio, proporcionándose sus expresiones matemáticas generalizadas y gráficas para su uso rutinario en las aplicaciones prácticas. Mediante los ensayos con ultrasonidos efectuados en campañas llevadas a cabo in situ, acompañados de la extracción de testigos del firme, se han podido evaluar los modelos propuestos. El máximo error relativo promedio en la estimación de la profundidad de las fisuras al aplicar dichos modelos no ha superado el 13%, con un nivel de confianza del 95%, en el conjunto de todos los ensayos realizados. La comprobación in situ de los modelos ha permitido establecer los criterios y las necesarias recomendaciones para su utilización sobre firmes en servicio. La experiencia obtenida posibilita la integración de esta metodología entre las técnicas de auscultación para la gestión de su conservación. Abstract Surface-initiated cracking of asphalt pavements constitutes one of the most frequent and important types of distress that occur in flexible bituminous pavements, as clearly has been demonstrated in the technical and experimental studies done over the past decade. However, this failure mechanism has not been taken into consideration for traditional methods of flexible pavement design. The concept of long-lasting pavements is based on adequate monitoring of the depth and extent of these deteriorations and on intervention at the most appropriate moment so as to contain them in the surface layer in the form of easily-accessible and repairable partial-depth topdown cracks, thereby prolonging the durability and serviceability of the pavement and reducing the overall cost of its life cycle. Therefore, to select the optimal maintenance strategy for perpetual pavements, it becomes essential to have access to methodologies that enable precise on-site identification, monitoring and control of top-down propagated cracks and that also permit a reliable, high-performance determination of the extent and depth of cracking. This PhD Thesis presents the results of systematic laboratory and in situ research carried out to obtain information about top-down cracking in asphalt pavements and to study methods of depth evaluation of this type of cracking using ultrasonic techniques. These results have demonstrated that the proposed non-destructive methodology –cost-effective, fast and easy-to-implement– (mainly used to date for concrete and metal structures, due to the difficulties caused by the viscoelastic nature of bituminous materials) can be applied with sufficient reliability and repeatability to asphalt pavements. Measurements are also independent of the asphalt thickness. Furthermore, it resolves some of the common inconveniences presented by other methods used to evaluate pavement cracking, such as core extraction (a destructive and expensive procedure that requires prolonged traffic interruptions) and other non-destructive techniques, such as those based on deflection measurements or ground-penetrating radar, which are not sufficiently precise to measure surface cracks. To obtain these results, extensive tests were performed on laboratory specimens. Different empirical conditions were studied, such as various types of hot bituminous mixtures (AC, SMA and PA), differing thicknesses of asphalt and adhesions between layers, varied temperatures, surface textures, filling materials and water within the crack, different sensor positions, as well as an ample range of possible crack depths. The methods employed in the study are based on a series of measurements of ultrasonic pulse velocities or transmission times over a single accessible side or surface of the material that make it possible to obtain a signal transmission coefficient (relative or auto-calibrated readings). Measurements were taken at low frequencies by two short-pulse ultrasonic devices: one equipped with dry point contact transducers (DPC) and the other with flat contact transducers that require a specially-selected coupling material (CPC). In this way, some of the traditional inconveniences presented by the use of conventional transducers were overcome and a prior preparation of the surfaces was not required. The auto-compensating technique eliminated systematic errors and the need for previous local calibration, demonstrating the potential for this technology. The experimental results have been compared with simplified theoretical models that simulate ultrasonic wave propagation in cracked bituminous materials, which had been previously deduced using an analytical approach and have permitted the correct interpretation of the aforementioned empirical results. These models were subsequently calibrated using the laboratory results, providing generalized mathematical expressions and graphics for routine use in practical applications. Through a series of on-site ultrasound test campaigns, accompanied by asphalt core extraction, it was possible to evaluate the proposed models, with differences between predicted crack depths and those measured in situ lower than 13% (with a confidence level of 95%). Thereby, the criteria and the necessary recommendations for their implementation on in-service asphalt pavements have been established. The experience obtained through this study makes it possible to integrate this methodology into the evaluation techniques for pavement management systems.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

Development of a novel HCPV nonimaging concentrator with high concentration (>500x) and built-in spectrum splitting concept is presented. It uses the combination of a commercial concentration GaInP/GaInAs/Ge 3J cell and a concentration Back-Point-Contact (BPC) silicon cell for efficient spectral utilization, and external confinement techniques for recovering the 3J cell's reflection. The primary optical element (POE) is a flat Fresnel lens and the secondary optical element (SOE) is a free-form RXI-type concentrator with a band-pass filter embedded in it - Both the POE and SOE performing Köhler integration to produce light homogenization on the receiver. The band-pass filter transmits the IR photons in the 900-1200 nm band to the silicon cell. A design target of an "equivalent" cell efficiency ~46% is predicted using commercial 39% 3J and 26% Si cells. A projected CPV module efficiency of greater than 38% is achievable at a concentration level larger than 500X with a wide acceptance angle of ±1°. A first proof-of concept receiver prototype has been manufactured using a simpler optical architecture (with a lower concentration, ~100x and lower simulated added efficiency), and experimental measurements have shown up to 39.8% 4J receiver efficiency using a 3J cell with a peak efficiency of 36.9%.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

A novel HCPV nonimaging concentrator concept with high concentration (>500×) is presented. It uses the combination of a commercial concentration GaInP∕GaInAs∕Ge 3J cell and a concentration Back‐Point‐Contact (BPC) concentration silicon cell for efficient spectral utilization, and external confinement techniques for recovering the 3J cell′s reflection. The primary optical element (POE) is a flat Fresnel lens and the secondary optical element (SOE) is a free‐form RXI‐type concentrator with a band‐pass filter embedded it, both POE and SOE performing Köhler integration to produce light homogenization. The band‐pass filter sends the IR photons in the 900–1200 nm band to the silicon cell. Computer simulations predict that four‐terminal terminal designs could achieve ∼46% added cell efficiencies using commercial 39% 3J and 26% Si cells. A first proof‐of concept receiver prototype has been manufactured using a simpler optical architecture (with a lower concentration, ∼ 100× and lower simulated added efficiency), and experimental measurements have shown up to 39.8% 4J receiver efficiency using a 3J with peak efficiency of 36.9%

Relevância:

60.00% 60.00%

Publicador:

Resumo:

La mejora en la eficiencia energética y la reducción de la tasa de fallos en los contactos lubricados son aspectos que resultan de gran interés en numerosos sectores de la industria, y plantean en estos momentos nuevas dificultades operativas y retos para un futuro próximo. Los avances tecnológicos han incrementado las exigencias técnicas que se requieren a los aceites para cumplir su función al extender sus variables operativas a un mayor espectro de aplicaciones, tanto de condiciones de funcionamiento como a la gran variedad de nuevos materiales constitutivos de los engranajes en los que se tiene que utilizar. Por ello, actualmente se está incentivado el desarrollo de nuevos procedimientos que permitan comprender el comportamiento de este tipo de contactos lubricados, con el fin de lograr mejoras técnicas en su diseño y la correcta selección del aceite. En esta Tesis Doctoral se presenta una metodología de cálculo numérico que permite simular el comportamiento de contactos elastohidrodinámicos (EHD) puntuales, como puede ser el caso de un rodamiento. La resolución de este problema presenta diversas complejidades matemáticas y exige el desarrollo de un elaborado procedimiento de cálculo basado en técnicas multinivel. Para hacer del procedimiento una herramienta válida en un gran número de condiciones de funcionamiento y tipos de lubricantes, se ha tenido en cuenta en el cálculo la posible aparición de comportamientos no-Newtonianos del lubricante y fenómenos de generación y disipación de calor, provocados por el movimiento relativo del fluido y las superficies en contacto. Para la validación del procedimiento, se han contrastado los resultados numéricos obtenidos con nuestro método, con los resultados numéricos y experimentales publicados por otros autores y con valores experimentales propios medidos en un equipo de ensayo de contacto puntual tipo MTM. El desarrollo de este programa ha dotado a la División de Ingeniería de Máquinas de una herramienta que ha permitido, y sobre todo va permitir, evaluar la importancia de cada uno de los parámetros reológicos en los diferentes problemas que va a tener que abordar, evaluación que hasta el momento se realizaba con métodos aproximados que describen la fenomenología con mucha menos precisión. A la hora de emplear nuestro procedimiento numérico para simular situaciones reales, nos hemos encontrado con el obstáculo de que es muy complicado encontrar, en la bibliografía y bases de datos, los parámetros que caracterizan el comportamiento reológico del lubricante en las condiciones de presión, temperatura y grado de cizallamiento habituales en las que se trabaja en este tipo de contactos, y las pocas medidas que existen para estas condiciones de funcionamiento son poco fiables. Por ello como complemento al objetivo principal de esta Tesis hemos desarrollado una metodología para caracterizar los lubricantes en estas condiciones extremas. Dicha metodología está basada en la buena descripción que hace nuestro programa del coeficiente de fricción, lo que nos ha permitido obtener los parámetros reológicos del III lubricante a partir de las medidas experimentales del coeficiente de fricción generado en un equipo MTM lubricado con el lubricante que se desea caracterizar. Madrid, Octubre de 2012 IV Improving energy efficiency and reducing the failure rate in lubricated contacts are issues that are of great interest in many sectors of industry, and right now posed operational difficulties and new challenges for the near future. Technological advances have increased the technical demands required to oils to fulfil its role by extending its operational variables to a wider range of applications, both operating conditions and to the wide variety of new materials which constitute the gear in which must be used. For this reason, has being encouraged currently to develop new procedures to understand the behaviour of this type of lubricated contacts, in order to achieve improvements in design techniques and the correct oil selection. In this Thesis we present a numerical methodology to simulate the puntual elastohydrodynamic contact behaviour (EHD), such as a roller bearing. The resolution of this problem presents various mathematical complexities and requires the development of an elaborate calculation procedure based on multilevel techniques. To make the procedure a valid tool in a wide range of operating conditions and types of lubricants, has been taken into account in calculating the possible occurrence of non-Newtonian behaviour of the lubricant and phenomena of generation and dissipation of heat, caused by the fluid relative motion and contacting surfaces. For the validation of the method, we have compared the numerical results obtained with our method with numerical and experimental results published by other authors also with own experimental values measured on point-contact test equipment MTM. The development of this program has provided the Machines Engineering Division of a tool that has allowed, and especially will allow to evaluate the importance of each of the rheological parameters on the various problems that will have to be addressed, evaluation performed hitherto described methods that phenomenology approximated with much less accuracy. When using our numerical procedure to simulate real situations we have encountered the obstacle that is very difficult to find, in the literature and database, parameters characterizing the rheological behaviour of the lubricant in the usual conditions of pressure, temperature and shear rate in which you work in this type of contact, and the few measures that exist for these operating conditions are unreliable. Thus in addition to the main objective of this thesis, we have developed a methodology to characterize the lubricants in these extreme conditions. This methodology is based on the good description, which makes our program, of the coefficient of friction, that allowed us to obtain the lubricant rheological parameters from experimental measurements of the friction coefficient generated on lubricated MTM equipment with the lubricant to be characterized.